Mitsubishi Electric FX3G SERIES Programming Manual page 854

FX /FX /FX Series Programmable Controllers
3G 3U 3UC
Programming Manual - Basic & Applied Instruction Edition
Number and name
Timing Clock (Refer to Section 24.3 for details.) and Positioning [FX
D 8360 Lower [Y002] Current value register
D 8361 Upper
D 8362 [Y002] Bias speed Default: 0
D 8363 Lower [Y002] Maximum speed
D 8364 Upper
D 8365 [Y002] Creep speed Default: 1000
D 8366 Lower [Y002] Zero return speed
D 8367 Upper
D 8368 [Y002] Acceleration time Default: 100
D 8369 [Y002] Deceleration time Default: 100
D 8370 Lower [Y003] Current value register
D 8371 Upper
D 8372 [Y003] Bias speed Default: 0
D 8373 Lower [Y003] Maximum speed
D 8374 Upper
D 8375 [Y003] Creep speed Default: 1000
D 8376 Lower [Y003] Zero return speed
D 8377 Upper
D 8378 [Y003] Acceleration time Default: 100
D 8379 [Y003] Deceleration time Default: 100
[D]8380 to [D]8392 Not used
RS2 (FNC 87) [ch0] [FX PLCs] (Refer to Data Communication Edition for details.)
3G
RS2 (FNC 87) [ch0] Communication format setting
D 8370
D 8371 Not used
*1
RS2 (FNC 87) [ch0] Remaining points of transmit data
[D]8372
*1
RS2 (FNC 87) [ch0] Monitoring receive data points
[D]8373
D 8374
Not used
[D]8375 to [D]8378
D 8379 RS2 (FNC 87) [ch0] Time-out time setting
D 8380 RS2 (FNC 87) [ch0] Header 1 and 2 <Default: STX>
D 8381 RS2 (FNC 87) [ch1] Header 3 and 4
RS2 (FNC 87) [ch0] Terminator 1 and 2
D 8382
D 8383 RS2 (FNC 87) [ch0] Terminator 3 and 4
[D]8384 RS2 (FNC 87) [ch0] Receive sum (received data)
[D]8385 RS2 (FNC 87) [ch0] Receive sum (calculated result)
[D]8386 RS2 (FNC 87) [ch0] Send sum
[D] 8387 to [D] 8388 Not used
[D]8389 Operation mode display [ch0]
[D] 8390 to [D] 8392 Not used
*1. Cleared when the PLC switches from RUN to STOP.
*2. Available only when two FX
852
Content of register
Default: 0
Default: 100000
Default: 50000
Default: 0
Default: 100000
Default: 50000
<Default: ETX>
-2HSY-ADP adapters are connected to an FX
3U
37 Operation of Special Devices (M8000 -, D8000 -)
37.1 Special Device List (M8000 -, D8000 -)
FX FX FX
3G 3U 3UC
and FX PLCs] (Refer to Positioning Control Edition for details.)
3U 3UC
–
*2
–
–
*2
– –
–
*2
–
–
*2
– –
–
*2
–
–
*2
– –
*2
– –
– –
– –
– – –
– –
– –
– – –
– – –
– –
– –
– –
– –
– –
– –
– –
– –
– – –
– –
– – –
Applicable model
Correspond-
ing special FX FX FX FX
1S 1N 2N
device
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
– – – –
PLC.
3U
FX
1NC 2NC
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –