Toyota 1PZ Repair Manual page 320

Specification (Cont'd)
Engine tune-up
Valve clearance
(cont'd)
New valve adjusting shim thickness
Injection timing
Plunger stroke
Idle speed
Maximum speed
A/C idle-up setting speed
Injection order
Compression Engine revolution at 250 rpm
pressure 1PZand1HZ
1HD-T
Difference of pressure between each cylinder
Idler pulley Free length
tension spring
Installed load
Timing gear
Idler gear inside diameter
Idler gear shaft diameter
Idler gear oil clearance
Gear backlash
Idler gear thrust clearance
SERVICE SPECIFICATIONS - Engine Mechanical
Intake
Exhaust
1 PZ
1HZ
1HD-T
1 PZ
1HZ (M/T)
1 HZ (A/T)
1HD-T(M/T)
1HD-T (A/T)
1 PZ and 1 HZ
1HD-T
1 PZ
1 HZ and 1HD-T
at 90.1 mm (3.547 in.)
0.1 5 - 0.25 mm
0.35 - 0.45 mm
2.35 mm
2.40 mm
2.45 mm
2.50 mm
2.55 mm
2.60 mm
2.65 mm
2.70 mm
2.75 mm
2.80 mm
2.85 mm
2.90 mm
2.95 mm
3.00 mm
3.05 mm
3.10 mm
3.15 mm
3.20 mm
3.25 mm
3.30 mm
0.82 - 0.88 mm
1.03-1.09 mm
1.29-1.35 mm
650 rpm
650 rpm
710 rpm
650 rpm
800 rpm
4,600 rpm
4,400 rpm
950 rpm
1 - 2 - 4 - 5 - 3
1 _ 4 _ 2 - 6 - 3 - 5
2
STD 37.0 kg/cm (526 psi, 3,628 kPa) or more
2
Limit 27.0 kg/cm (384 psi, 2,648 kPa)
2
STD 35.0 kg/cm (498 psi, 3,432 kPa) or more
2
25.0 kg/cm (356 psi, 2,452 kPa)
Limit
2
5.0 kg/cm (71 psi, 490 kPa) or less
72.7 mm
23 - 28 kg (50.7 - 61.7 Ib, 225 - 275 N)
45.000-45.025 mm
44.950 - 44.975 mm
0.025 - 0.075 mm
STD
Limit 0.20 mm
STD 0.05 - 0.1 5 mm
Limit 0.30 mm
STD 0.05 - 0.1 5 mm
Limit 0.30 mm
A-3
0.006 - 0.010 in.
0.014 - 0.018 in.
0.0925 in.
0.0945 in.
0.0965 in.
0.0984 in.
0.1004 in.
0.1024 in.
0.1043 in.
0.1063 in.
0.1083 in.
0.1102 in.
0.1122 in.
0.1142 in.
0.1161 in.
0.1181 in.
0.1201 in.
0.1220 in.
0.1240 in.
0.1260 in.
0.1280 in.
0.1299 in.
0.0323 - 0.0346 in.
0.0406-0.0429 in.
0.0508-0.0531 in.
2.862 in.
1.7717 - 1.7726 in.
1.7679 - 1.7707 in.
0.0010 - 0.0030 in.
0.0079 in.
0.0020 - 0.0059 in.
0.0118 in.
0.0020 - 0.059 in.
0.0118 in.