Buell XB 2008 Series Service Manual page 664

FASTENER
Cooling fan fasteners
Cooling fan fasteners
Countershaft retaining screw
Crankcase 5/16 in. fasteners
Crankcase 5/16 in. screws
Crank position sensor screw
Cylinder head screws (final tightening)
Cylinder head screws (final tightening)
Cylinder head screws (initial tightening)
Cylinder head screws (initial tightening)
Cylinder studs
damper rod jamnut
Deflector fasteners
Deflector jam nuts
Deflector pivot shaft risers
ECM fasteners
ECM fasteners, Ulysses
Electronic control module fasteners
Electronic control module fasteners,
Lightning
Electronic control module fasteners,
Ulysses
Engine oil drain plug
Engine shift lever pinch screw
Engine shroud air scoop fasteners
XII TORQUE VALUES
2008 Buell XB Models Service Manual
TORQUE VALUE
12-36 in-lbs
12-36 in-lbs
33-37 ft-lbs
15-19 ft-lbs
15-19 ft-lbs
80-100 in-lbs
13-15 ft-lbs
13-15 ft-lbs
96-120 in-lbs
96-120 in-lbs
10-20 ft-lbs
22-30 ft-lbs
24-36 in-lbs
39-48 in-lbs
43-49 in-lbs
36-60 in-lbs
36-60 in-lbs
72-96 in-lbs
48-72 in-lbs
36-60 in-lbs
26-29 ft-lbs
48-60 in-lbs
12-36 in-lbs
1.4-4.1 Nm 4.10 COOLING FAN, Installation
1.4-4.1 Nm 7.23 MAIN WIRE HARNESS, Installation
44.8-50 Nm 6.15 SHIFTER SHAFT, Installation / LOCTITE 271
(red)
20.3-25.0 Nm 6.14 TRANSMISSION INSTALLATION, Installing
Right Crankcase / Apply several drops of LOCTITE
271 (red) to last few threads.
20-26 Nm 3.17 CRANKCASE, Assembly / LOCTITE 272
9.0-11.3 Nm 7.20 CRANKSHAFT POSITION SENSOR
(CKP), Installation
18-20 Nm 3.6 CYLINDER HEAD, Cylinder Head Installation /
Special procedure and pattern required for tight-
ening
18-20 Nm 3.6 CYLINDER HEAD, Cylinder Head Installation /
Special procedure and pattern required for tight-
ening
11-14 Nm 3.6 CYLINDER HEAD, Cylinder Head Installation /
Special procedure and pattern required for tight-
ening
11-14 Nm 3.6 CYLINDER HEAD, Cylinder Head Installation /
Special procedure and pattern required for tight-
ening
14-27 Nm 3.17 CRANKCASE, Assembly / Special method
required to tighten
30-41 Nm 2.17 FRONT FORK:
XB12STT/XB12X/XB12XT, Assembly
2.7-4.1 Nm 2.30 DEFLECTORS:
XB9SX/XB12STT/XB12X/XB12XT, Assembly and
Installation
4.4-5.4 Nm 2.30 DEFLECTORS:
XB9SX/XB12STT/XB12X/XB12XT, Assembly and
Installation
4.8-5.5 Nm 2.30 DEFLECTORS:
XB9SX/XB12STT/XB12X/XB12XT, Assembly and
Installation
4-6.7 Nm 2.45 LEFT TAIL SECTION AND BATTERY PAN:
XB12X/XB12XT, Assembly
4.0-6.8 Nm 2.47 RIGHT TAIL SECTION:
XB12X/XB12XT, Assembly
8-11 Nm 2.28 HEADLAMP ASSEMBLY AND SUPPORT
BRACKET, Installation: Firebolt
5.4-8 Nm 4.3 ELECTRONIC CONTROL MODULE
(ECM), Installation: Lightning
4-6.8 Nm 4.3 ELECTRONIC CONTROL MODULE
(ECM), Installation: Ulysses
35-39 Nm 1.5 ENGINE OIL AND FILTER, Change Engine Oil
and Filter / LOCTITE 565 THREAD SEALANT
5.4-6.8 Nm 2.27 CLUTCH CONTROL, Assembly and Installa-
tion
1-4 Nm 2.52 AIR SCOOPS, Engine Shroud Air Scoop
NOTES