Monitor Port-Channels - Dell Force10 S4810P Configuration Manual
High-density, 1ru 48-port 10gbe switch
Hide thumbs
Also See for Force10 S4810P:
- Manual (60 pages) ,
- Quick start manual (27 pages) ,
- Reference manual (1637 pages)
Table of Contents
Advertisement
Figure 46-28. Binary Representation of Interface Index
For interface indexing, slot and port numbering begins with the binary one. If the Dell Force10 system
begins slot and port numbering from 0, then the binary 1 represents slot and port 0. For example, the index
number in
Figure 46-28
belongs to Slot 1. This is because the port for this example is on an E-Series which begins numbering slots
from 0. You must subtract 1 from the slot number 2, which yields 1, the correct slot number for interface 1/
21.
Note that the interface index does not change if the interface reloads or fails over. On the S-Series, if the
unit is renumbered (for any reason) the interface index will change during a reload.
Monitor Port-channels
To check the status of a Layer 2 port-channel, use f10LinkAggMib (.1.3.6.1.4.1.6027.3.2). Below , Po 1 is a
switchport and Po 2 is in Layer 3 mode.
[senthilnathan@lithium ~]$ snmpwalk -v 2c -c public 10.11.1.1 .1.3.6.1.4.1.6027.3.2.1.1
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.1.1 = INTEGER: 1
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.1.2 = INTEGER: 2
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.2.1 = Hex-STRING: 00 01 E8 13 A5 C7
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.2.2 = Hex-STRING: 00 01 E8 13 A5 C8
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.3.1 = INTEGER: 1107755009
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.3.2 = INTEGER: 1107755010
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.4.1 = INTEGER: 1
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.4.2 = INTEGER: 1
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.5.1 = Hex-STRING: 00 00
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.5.2 = Hex-STRING: 00 00
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.6.1 = STRING: "Gi 5/84 " << Channel member for Po1
SNMPv2-SMI::enterprises.6027.3.2.1.1.1.1.6.2 = STRING: "Gi 5/85 " << Channel member for Po2
dot3aCommonAggFdbIndex
SNMPv2-SMI::enterprises.6027.3.2.1.1.6.1.1.1107755009.1 = INTEGER: 1107755009
dot3aCommonAggFdbVlanId
SNMPv2-SMI::enterprises.6027.3.2.1.1.6.1.2.1107755009.1 = INTEGER: 1
dot3aCommonAggFdbTagConfig
SNMPv2-SMI::enterprises.6027.3.2.1.1.6.1.3.1107755009.1 = INTEGER: 2 (Tagged 1 or Untagged 2)
dot3aCommonAggFdbStatus
gives the binary 2 for the slot number, though interface GigabitEthernet 1/21
Simple Network Management Protocol (SNMP) | 969
Advertisement
Table of Contents
Troubleshooting
