Page 1 WS2000 Wireless Switch CLI Reference Guide...
Page 2 © 2009 Motorola, Inc. All rights reserved. MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. Symbol is a registered trademark of Symbol Technologies, Inc. All other product or service names are the property of their respective owners.
Page 3: Table Of Contents
Contents Chapter 1: Product Overview 1.1 WS2000 Wireless Switch CLI Reference Guide............1-1 1.2 System Overview .
Page 4 TOC-2 WS2000 Wireless Switch CLI Reference Guide show ..................3-21 3.4 Network AP Test Commands .
Page 5 TOC-3 3.13 Network Firewall Policy Commands..............3-64 policy .
Page 6 TOC-4 WS2000 Wireless Switch CLI Reference Guide show ..................3-108 3.21 Network Router Commands .
Page 7 TOC-5 3.30 Network WAN NAT Commands ..............3-150 nat .
Page 8 TOC-6 WS2000 Wireless Switch CLI Reference Guide show ..................3-200 3.37 Network WLAN Rogue AP Roguelist Commands.
Page 9 TOC-7 set ..................3-239 add .
Page 10 TOC-8 WS2000 Wireless Switch CLI Reference Guide delete ..................3-281 show .
Page 11 TOC-9 show ..................4-36 4.8 System RADIUS Client Commands.
Page 12 TOC-10 WS2000 Wireless Switch CLI Reference Guide show ..................4-77 4.18 System SNMP Traps Commands .
Page 13 TOC-11 show ..................4-126 4.27 System Test Commands .
Page 14 TOC-12 WS2000 Wireless Switch CLI Reference Guide...
Page 15: Chapter 1: Product Overview
Product Overview 1.1 WS2000 Wireless Switch CLI Reference Guide This guide is intended to support administrators responsible for understanding, configuring and maintaining the Wireless Switch. This document provides information for the system administrator to use the command line interface during the initial setup and configuration of the system. It also serves as a reference guide for the administrator to use while updating or maintaining the system.
Page 16: Document Conventions
1-2 WS2000 Wireless Switch CLI Reference Guide 1.1.2 Document Conventions Notes and Warnings NOTE: Indicates special tips or requirements CAUTION: Indicates a condition that can cause equipment damage or data loss WARNING! Indicates a condition or procedure that could result in personal injury or equip- ment damage CLI Conventions command / keyword...
Page 17 Product Overview The pipe symbol. This is used to separate the variables/keywords in a list. For example, the command admin(network.wan.vpn)> set ..is documented as set [ike|type|sub|remip|..] where: • set – The command • [ike|type|sub|remip|...] – Indicates the different commands that can be combined with the set command.
Page 18: System Overview
1-4 WS2000 Wireless Switch CLI Reference Guide 1.2 System Overview The WS2000 Wireless Switch provides a low-cost, feature-rich option for sites with one to six Access Ports. The WS2000 Wireless Switch works at the center of a network’s infrastructure to seamlessly and securely combine wireless LANs (WLANs) and wired networks.
Page 19: Hardware Overview
Product Overview 1.3 Hardware Overview The WS2000 Wireless Switch provides a fully integrated solution for managing every aspect of connecting wireless LANs (WLANs) to a wired network. This wireless switch can connect directly to a cable or DSL modem, and can also connect to other wide area networks through a Layer 2/3 device (such as a switch or router).
Page 20: Ws 2000 Wireless Switch Led Functions
1-6 WS2000 Wireless Switch CLI Reference Guide 1.3.2 WS 2000 Wireless Switch LED Functions The switch has a large blue LED on the right front that indicates that the switch is powered on. Each port on the WS 2000 Wireless Switch has either two or three LEDs that indicate the status of the port. Ports 1-4, which supply 802.3af Power over Ethernet (PoE), have three LEDs.
Page 21: Software Overview
Product Overview 1.4 Software Overview The WS2000 Wireless Switch software provides a fully integrated solution for managing every aspect of connecting Wireless LANs (WLANs) to a wired network, and includes the following components: 1.4.1 Operating System (OS) Services Operating System (OS) Services determine how the WS2000 Wireless Switch communicates with existing network and operating system-centric software services, including: •...
Page 22 1-8 WS2000 Wireless Switch CLI Reference Guide...
Page 23: Chapter 2: Admin And Common Commands
Admin and Common Commands The term Common Commands is used to indicate that these commands are available through the WS2000 Wireless Switch’s CLI. These commands provide easy access to help, navigation, and to save configuration changes. This chapter also lists of commands available at the admin menu. •...
Page 24: Common Commands
2-2 WS2000 Wireless Switch System Reference Guide 2.1 Common Commands Admin and Common Commands The following commands are available through the WS2000 CLI. Command Description Ref. Displays the list of commands in the current menu. page 2-3 help Displays general user interface help. page 2-4 save Saves the configuration to the system flash.
Page 25 Admin and Common Commands 2.1.1 ? Command Common Commands Displays the commands available under the admin menu. Syntax Parameters None Example admin> ? admin>? help : display general user interface help passwd : change password summary : show system summary network : go to network sub menu stats...
Page 26: Help
2-4 WS2000 Wireless Switch System Reference Guide 2.1.2 help Command help Common Commands Displays general CLI user interface help. Syntax help Parameters None Example admin>help : display command help - Eg. ?, show ?, s? <ctrl-q> : go backwards in command history <ctrl-p>...
Page 27: Quit
Admin and Common Commands 2.1.3 quit Command quit Common Commands Quits the command line interface. Requires you to logon again. This command appears in all the submenus under menu. In each case, it has the same function, to exit admin out of the CLI.
Page 28: Save
2-6 WS2000 Wireless Switch System Reference Guide 2.1.4 save Command save Common Commands Saves the configuration to system flash. This command appears in all of the submenus under admin. In each case, it has the same function, to save the configuration. The save command must be issued before leaving the CLI for the settings to be retained. Syntax save Parameters...
Page 29 Admin and Common Commands 2.1.5 .. Command Common Commands Displays the parent menu of the current menu. This command appears in all of the submenus under admin. In each case, it has the same function, to move up one level in the directory structure. Syntax Parameters None...
Page 30 2-8 WS2000 Wireless Switch System Reference Guide 2.1.6 / Command Common Commands Displays the root menu, that is, the top-level CLI menu. This command appears in all of the submenus under admin. In each case, it has the same function, to move up to the top level in the directory structure.
Page 31: Admin Menu Commands
Admin and Common Commands 2.2 Admin Menu Commands Admin and Common Commands The following commands are only available at the admin menu. Command Description Ref. passwd Changes the admin password. page 2-10 summary Displays a system summary. page 2-11 network Goes to the network menu.
Page 32: Passwd
2-10 WS2000 Wireless Switch System Reference Guide 2.2.1 passwd Command passwd Admin Menu Commands Changes the password for the administrative logins - admin, guest-admin, and manager. Syntax passwd [admin|manager|guest-admin] Parameters passwd Passwords for the Administrator, Guest-admin, and Manager accounts [admin|manager|guest-admin] can be changed.
Page 33: Summary
2-11 Admin and Common Commands 2.2.2 summary Command summary Admin Menu Commands Displays system summary for the WS2000 Wireless Switch. The information displayed includes high-level characteristics and settings for WAN, subnet, and WLAN. Syntax summary Parameters None Example admin> summary System Information WS2000 firmware version : 2.4.0.0-005X...
Page 34 2-12 WS2000 Wireless Switch System Reference Guide WLAN 5 Information ess identifier : 105 wlan mode : disable vlan_id enc type : none auth type : none WLAN 6 Information ess identifier : 106 wlan mode : disable vlan_id enc type : none auth type : none...
Page 35 2-13 Admin and Common Commands Subnet 3 Information subnet interface : disable ip address : 192.168.2.1 network mask : 255.255.255.0 dhcp mode : server default gateway : 192.168.2.1 ports wlan : wlan3 Subnet 4 Information subnet interface : disable ip address : 192.168.3.1 network mask : 255.255.255.0...
Page 36 2-14 WS2000 Wireless Switch System Reference Guide...
Page 37: Chapter 3: Network Cli Commands Reference
Network CLI Commands Reference Network commands are used to configure the different network parameters of the WS2000 Wireless Switch. 3.1 network Admin Menu Commands Use the command to go the Network menu. network admin> network admin(network)> The following commands are available under the Network menu: Command Description Ref.
Page 38 3-2 WS2000 Wireless Switch System Reference Guide...
Page 39: Network Ap Commands
Network CLI Commands Reference 3.2 Network AP Commands network Displays the Access Port submenu. The functionality provided by this menu is supplied by various screen under the Wireless menu item of the Web interface. Syntax admin(network)> ap admin(network.ap)> The items available under this command are shown below. Command Description Adds entries to the Access Port adoption list.
Page 40: Add
3-4 WS2000 Wireless Switch System Reference Guide 3.2.1 Network AP add Command Network AP Commands Adds entries to the Access Port adoption list. This allows the Access Ports with the MAC addresses specified in the command to associate with the specified WLAN. Performs functionality available in the Access Port Adoption List area of the Wireless screen.
Page 41: Copydefaults
Network CLI Commands Reference 3.2.2 Network AP copydefaults Command copydefaults Network AP Commands Copies default Access Port settings to a connected Access Port. In the Web interface, the defaults are set on the Wireless, default AP screens (one for each radio type). Syntax copydefault <idx>...
Page 42: Delete
3-6 WS2000 Wireless Switch System Reference Guide 3.2.3 Network AP delete Command delete Network AP Commands Deletes entries from the Access Port adoption list. In the Web interface, this functionality is found on the Wireless screen in the Access Port Adoption list area. Syntax delete <idx>...
Page 43: Forget
Network CLI Commands Reference 3.2.4 Network AP forget Command forget Network AP Commands Forgets the AP parameters at a particular index specified by the <idx> value. Syntax forget [<idx>|all] Parameters <idx>|all <idx> – The index to remove the AP parameters. all –...
Page 44: List
3-8 WS2000 Wireless Switch System Reference Guide 3.2.5 Network AP list Command list Network AP Commands Displays entries in the Access Port adoption list for a specified wireless LAN. Syntax list <idx> Parameters <idx> Lists the Access Port adoption entries for WLAN <idx> (1-8). Example The following example shows the access port adoption list for WLAN 1.
Page 45: Remap
Network CLI Commands Reference 3.2.6 Network AP remap Command remap Network AP Commands Remaps the channels for a radio at index specified by <idx>. Syntax remap [<idx>|all] Parameters <idx>|all <idx> – Remaps all channels for a radio specified by the index <idx> –...
Page 46: Reset
3-10 WS2000 Wireless Switch System Reference Guide 3.2.7 Network AP reset Command reset Network AP Commands Resets an Access Port. Syntax reset ap <idx> Parameters ap <idx> <idx> – Resets the Access Port with index <idx> in the Access Port Adoption list. Example --------------------------------------- index...
Page 47: Revert
3-11 Network CLI Commands Reference 3.2.8 Network AP revert Command revert Network AP Commands Reverts an Access Port to an Access Point (Only on AP4131 or AP4121). Syntax revert ap <idx> Parameters ap <idx> <idx> – Reverts the Access Port with index <idx> to an Access Point. Only on AP4131 and AP 4121.
Page 48: Set
3-12 WS2000 Wireless Switch System Reference Guide 3.2.9 Network AP set Commands Network AP Commands Sets Access Port parameters. Syntax set [beacon|ch_mode|div|dtim|loc|name|primary|rate| reg|rts|short-pre|802.1x|ap_scan|mac|radio_type| ap_type|sip_cac_mode|allowed_sip_session] Parameters beacon intvl Sets the beacon interval for Access Port <idx> (1–12) to <interval> in K-us (50– <idx>...
Page 49: Rts Threshold
3-13 Network CLI Commands Reference short-pre <idx> Enables or disables the short preamble mode for Access Port <idx> (1-12) [enable|disable] 802.1x <username> Sets the 802.1x username and password on AP 300 Access Ports. Both <password> parameters can be up to 64 characters long. mac <idx>...
Page 50 3-14 WS2000 Wireless Switch System Reference Guide beacon interval : 100 dtim period : 25 short preamble : enable security beacon (hide ess) : disable primary wlan index : wlan1 admin(network.ap)>...
Page 51: Show
3-15 Network CLI Commands Reference 3.2.10 Network AP show Command show Network AP Commands Shows Access Port parameters. Syntax show [ap|status|sip|legacy-mode] Parameters ap <idx> Shows Access Port <idx> (1-12) radio parameters. status Shows a list of Access Ports and their status. sip <idx>...
Page 52 3-16 WS2000 Wireless Switch System Reference Guide ap status : not connected ap index ap status : not connected ap status : not connected ap index ap status : not connected ap index ap status : not connected ap index ap status : not connected ap index...
Page 53: Network Ap Default Commands
3-17 Network CLI Commands Reference 3.3 Network AP Default Commands default Network AP Commands Displays the default Access Port (AP) submenu. Use these commands to set the default values for all APs. Syntax admin(network.ap)> default The items available under this command are shown below. Command Description Sets default Access Port parameters.
Page 54: Set
3-18 WS2000 Wireless Switch System Reference Guide 3.3.1 Network AP Default set Command Network AP Default Commands Sets the default Access Port parameters. Syntax set [beacon|ch_mode|div|dtim|primary|reg|rate|rts|short-pre|sensor-img| ap4131-img|ap4121-img] Parameters beacon intvl <type> Sets the default beacon interval for specified radio type <type> (one of <interval>...
Page 55 3-19 Network CLI Commands Reference short-pre <type> By default, enables or disables the short preamble mode for radios of [enable|disable] specified <type> (one of 802.11a, 802.11b, or 802.11b/g). sensor-img <loc> Sets the default location of the sensor image. Location is specified in the <loc>...
Page 56: Loadfromcf
3-20 WS2000 Wireless Switch System Reference Guide 3.3.2 Network AP Default loadfromcf Command loadfromcf Network AP Default Commands Immediately loads configured images from the CF card. Syntax loadfromcf Parameters None Example admin(network.ap.default)>loadfromcf...
Page 57: Show
3-21 Network CLI Commands Reference 3.3.3 Network AP Default show Command show Network AP Default Commands Shows the default Access Port parameters for a particular radio type. Syntax show [default|img-location] Parameters default <type> Shows the default Access Port parameters for radio type <type> (802.11a, 802.11b, 802.11bg).
Page 58: Network Ap Test Commands
3-22 WS2000 Wireless Switch System Reference Guide 3.4 Network AP Test Commands test Network AP Commands Displays the test submenu. Syntax admin(network.ap)> test admin(network.ap.test)> The items available under this command are shown below Command Description Ref. Switches the Access Port to a new channel. page 3-23 quit Quits the CLI.
Page 59: New
3-23 Network CLI Commands Reference 3.4.1 Network AP Test new Command Network AP Test Commands Switches the specified Access Port to a new channel. Syntax new <idx> <ch> Parameters <idx> <ch> Switches the Access Port indexed with <idx> (1–12) to channel <ch> (which must be a valid channel for the specified Access Port.
Page 60: Network Ap Selfheal Commands
3-24 WS2000 Wireless Switch System Reference Guide 3.5 Network AP Selfheal commands selfheal Network AP Commands Displays the selfheal submenu. Syntax admin(network.ap)> selfheal The items available under this menu are shown below. Command Description Ref. Sets self-heal parameters page 3-25 detect-neighbor Detects neighbors and prepares the neighbors list automatically page 3-26...
Page 61: Network Ap Selfheal Commands
3-25 Network CLI Commands Reference 3.5.1 Network AP Selfheal set Command Network AP Selfheal commands Sets the different self-heal parameters. Syntax set [interference-avoidance|neighbor-recovery] Parameters interference-avoidance • mode [enable|disable] – Sets the self-healing interference mode. Can be [mode one of enable or disable.
Page 62: Detect-Neighbor
3-26 WS2000 Wireless Switch System Reference Guide 3.5.2 Network AP Selfheal detect-neighbor Command detect-neighbor Network AP Selfheal commands Detects the neighbor devices. Syntax detect-neighbor Parameters None Example admin(network.ap.selfheal)>detect-neighbor admin(network.ap.selfheal)>...
Page 63: Add
3-27 Network CLI Commands Reference 3.5.3 Network AP Selfheal add Command Network AP Selfheal commands Adds entries into the selfheal AP-AP neighbor table. Syntax add <from-ap> <to-ap> Parameters <from-ap> <to-ap> Adds the specified APs into the neighbor-recovery table. <from-ap> and <to- ap>...
Page 64: Del
3-28 WS2000 Wireless Switch System Reference Guide 3.5.4 Network AP Selfheal del Command Network AP Selfheal commands Deletes entries from the selfheal AP-AP neighbor table. Syntax del <from-ap> <to-ap> Parameters <from-ap> <to-ap> Removes the specified APs from the neighbor-recovery table. <from-ap> and <to-ap>...
Page 65: Show
3-29 Network CLI Commands Reference 3.5.5 Network AP Selfheal show Command show Network AP Selfheal commands Shows the selfheal parameter details. Syntax show Parameters None Example admin(network.ap.selfheal)>show Interference Avoidance Mode : disable Retry Count : 14 Hold Time : 3600 Neighbor Recovery Mode : disable PORTAL-IDX...
Page 66: Network Ap Denyap Commands
3-30 WS2000 Wireless Switch System Reference Guide 3.6 Network AP Denyap Commands denyap Network AP Commands Displays the denyap submenu. Use the denyap submenu to manage APs that have been denied access to the switch. Syntax admin(network.ap)> denyap admin(network.ap.denyap)> The items available under this menu are shown below. Command Description Ref.
Page 67: Add
3-31 Network CLI Commands Reference 3.6.1 Network AP Denyap add Command Network AP Denyap Commands Add entries to the Access Port Deny List. Syntax add <mac> Parameters <mac> Adds the MAC specified in the <mac> parameter to the Access Port Deny List. MAC entries are to be entered without the ‘:’.
Page 68: Delete
3-32 WS2000 Wireless Switch System Reference Guide 3.6.2 Network AP Denyap delete Command delete Network AP Denyap Commands Deletes an entry in the Access Port Deny List. Syntax delete [<mac>|all] Parameters <mac> Deletes the MAC specified in the <mac> parameter from the Access Port Deny List. Deletes all the entries in the Access Port Deny List Example admin(network.ap.denyap)>show...
Page 69: Show
3-33 Network CLI Commands Reference 3.6.3 Network AP Denyap show Command show Network AP Denyap Commands Displays the Access Port Deny List. Syntax show Parameters None Example admin(network.ap.denyap)>show ---------------------------------------------------------------------- AP NIC MAC ---------------------------------------------------------------------- 00b4c2114535 00b4c2114534...
Page 70: Network Ap Smartscan Commands
3-34 WS2000 Wireless Switch System Reference Guide 3.7 Network AP Smartscan Commands smartscan Network AP Commands Displays the smartscan submenu. Syntax admin(network.ap)> smartscan admin(network.ap.smartscan)> The items available under this menu are shown below. Command Description Ref. Sets smartscan channels page 3-35 delete Removes smartscan channels page 3-36...
Page 71: Set
3-35 Network CLI Commands Reference 3.7.1 Network AP Smartscan set Command Network AP Smartscan Commands Sets the smartscan channels. These channels are the ones that are scanned for presence of WLANs. Syntax set [11a <11a>|11bg <11bg>] Parameters 11a <11a> Sets the smart scan channel list for the 5 GHz band. Channel list <11a> should be a comma separated list.
Page 72: Delete
3-36 WS2000 Wireless Switch System Reference Guide 3.7.2 Network AP Smartscan delete Command delete Network AP Smartscan Commands Deletes all the channels in the smartscan list for a specific radio. Syntax delete [11a <11a>|11bg <11bg>] Parameters 11a <11a> Sets the smart scan channel list for the 5 GHz band. Channel list <11a> should be a comma separated list.
Page 73: Show
3-37 Network CLI Commands Reference 3.7.3 Network AP Smartscan show Command show Network AP Smartscan Commands Displays the list of channels used for smartscan for the different radios. Syntax show [all] Parameters Shows the list of channels in the smartscan list. Example admin(network.ap.smartscan)>...
Page 74: Network Ap Test Commands
3-38 WS2000 Wireless Switch System Reference Guide 3.8 Network AP Test Commands test Network AP Commands Displays the test submenu. Use this submenu commands to test APs. Syntax admin(network.ap)> test admin(network.ap.test)> The items available under this command are shown below. Command Description Switches the AP to a new channel...
Page 75: New
3-39 Network CLI Commands Reference 3.8.1 Network AP Test new Command Network AP Test Commands Switches AP to a new channel. Syntax test <idx> <ch> Parameters <idx> The access port index for which the channel has to be changed <ch> The channel to change to.
Page 76: Network Ap Mesh Commands
3-40 WS2000 Wireless Switch System Reference Guide 3.9 Network AP Mesh Commands mesh Network AP Commands Displays the mesh submenu. Use this menu to configure the different Mesh Network parameters. Syntax admin(network.ap)> mesh admin(network.ap.mesh)> The items available under this command are shown below. Command Description Sets mesh parameters...
Page 77: Set
3-41 Network CLI Commands Reference 3.9.1 Network AP Mesh set Command Network AP Mesh Commands Sets the mesh related parameters. Syntax set [client|vlan|auto|base|max-clients] Parameters client <radio-idx> Enables or disables the mesh client for the radio with the index [enable|disable] <radio-idx> (1-12). wlan <radio-idx>...
Page 78 3-42 WS2000 Wireless Switch System Reference Guide admin(network.ap.mesh)> set auto 1 disable admin(network.ap.mesh)> show 1 ------------------------------------------------------------------------- "Mode" "WLAN" "Base Auto Selection" "Max Clients" ------------------------------------------------------------------------- Base and Client WLAN3 Disabled admin(network.ap.mesh)>...
Page 79: Add
3-43 Network CLI Commands Reference 3.9.2 Network AP Mesh add Command Network AP Mesh Commands Adds a preferred base to the device’s Preferred Base Bridge List. Syntax add <radio-idx> <mac> Parameters <radio-idx> Adds the base to the device’s Preferred Base Bridge List. The <radio-idx> (1-12) is the <mac>...
Page 80: Del
3-44 WS2000 Wireless Switch System Reference Guide 3.9.3 Network AP Mesh del Command Network AP Mesh Commands Removes a Mesh Base from the device’s Preferred Base Bridge List. Syntax del [<radio-idx>] [all|<index>] Parameters <radio-idx> • Removes all preferred bases from the device’s Preferred Base Bridge List for the [all|<index>] radio specified by the <radio-idx>...
Page 81: Preferred-List
3-45 Network CLI Commands Reference 3.9.4 Network AP Mesh preferred-list Command preferred-list Network AP Mesh Commands Displays the Preferred Base Bridge List for the device Syntax preferred-list <radio-idx> Parameters <radio-idx> Displays the selected radio’s (<radio-idx> (1-12)) Preferred Base Bridge List. Example admin(network.ap.mesh)>...
Page 82: Available-List
3-46 WS2000 Wireless Switch System Reference Guide 3.9.5 Network AP Mesh available-list Command available-list Network AP Mesh Commands Displays the list of available base bridges along with their MAC addresses and the RSSI. Syntax available-list <radio-idx> Parameters <radio-idx> Displays the available base bridges for a particular radio indicated by the <radio-idx> (1-12) value.
Page 83: Show
3-47 Network CLI Commands Reference 3.9.6 Network AP Mesh show Command show Network AP Mesh Commands Displays the mesh details for a particular radio. Syntax show <radio-idx> Parameters <radio-idx> Displays the mesh configuration information for the radio indicated by the <radio-idx>...
Page 84: Network Dchp Commands
3-48 WS2000 Wireless Switch System Reference Guide 3.10 Network DCHP Commands dhcp network Displays the DHCP submenu. Syntax admin(network)> dhcp admin(network.dhcp)> The items available under this command are shown below. Command Description Ref. Sets system updated flags. page 3-49 show Shows system updated flags.
Page 85 3-49 Network CLI Commands Reference 3.10.1 Network DHCP set Command Network DCHP Commands Sets parameters for automated firmware and configuration upgrades. Syntax set [firmwareupgrade|configureupgrade|interface| dhcpvendorclassid|autoupgradeinterval] firmwareupgrade [0|1] Enables (1) or disables (0) automatic switch firmware upgrade. configupgrade [0|1] Enables (1) or disables (0) automatic switch configuration update. interface <iface>...
Page 86: Set
3-50 WS2000 Wireless Switch System Reference Guide 3.10.2 Network DHCP show Command show Network DCHP Commands Displays system updated flags. Syntax show all Parameters Displays all of the DHCP-related system update parameters. Example admin(network.dhcp)>show all Auto Firmware upgrade flag Auto Config upgrade flag Interface Dhcp Vendor Class Id : SymbolWS.WS2K-V2-0...
Page 87 3-51 Network CLI Commands Reference 3.11 Network Firewall Commands network Displays the firewall submenu. Syntax admin(network)> fw admin(network.fw)> The items available under this command are shown below. Command Description Ref. Sets firewall parameters. page 3-52 show Shows firewall parameters. page 3-54 submap Goes to the subnet mapping submenu.
Page 88: Network Firewall Commands
3-52 WS2000 Wireless Switch System Reference Guide 3.11.1 Network Firewall set Command Network Firewall Commands Sets firewall parameters. In the Web interface, this functionality is provide by the Network->Firewall screen. Syntax set [mode|override|ftp|ip|seq|src|syn|win|spoof|rst| range|netbios-alg] [enable|disable] set mime [filter|hdr|len] set mime filter [enable|disable] set mime hdr <count>...
Page 89 3-53 Network CLI Commands Reference ftp bounce attack filter : enable syn flood attack filter : enable unaligned ip timestamp filter : enable source routing attack filter : enable winnuke attack filter : enable seq num prediction attack filter : enable mime flood attack filter : enable max mime header length...
Page 90: Show
3-54 WS2000 Wireless Switch System Reference Guide 3.11.2 Network Firewall show Command show Network Firewall Commands Displays the firewall parameters. Syntax show all Parameters Shows all firewall settings. Example admin(network.fw)>show all Firewall Status : enable Subnet Access Override : disable Configurable Firewall Filters ftp bounce attack filter : enable...
Page 91: Timeradd
3-55 Network CLI Commands Reference 3.11.3 Network Firewall timeradd Command timeradd Network Firewall Commands Adds a new named timeout value. Syntax timeradd <name> <protocol> <port> <value> Parameters timeradd <name> Adds a new named timeout value. <protocol> • <name> is the name of the time out value (1-15 characters) <port>...
Page 92: Timerdel
3-56 WS2000 Wireless Switch System Reference Guide 3.11.4 Network Firewall timerdel Command timerdel Network Firewall Commands Deletes a named timeout value. Syntax timerdell <timer name> Parameters timerdel <timername> Deletes a timer named <timer name>. Example admin(network.fw)>timeradd newudp udp 21 4500 admin(network.fw)>timerlist ----------------------------------------------------------- Name...
Page 93: Timerlist
3-57 Network CLI Commands Reference 3.11.5 Network Firewall timerlist Command timerlist Network Firewall Commands Displays all named time outs. Syntax timerlist Parameters None Example admin(network.fw)>timerlist ----------------------------------------------------------- Name Protocol Port Timeout ( Secs ) ----------------------------------------------------------- newtcp 4500 newudp 4500 admin(network.fw)
Page 94: Timerset
3-58 WS2000 Wireless Switch System Reference Guide 3.11.6 Network Firewall timerset Command timerset Network Firewall Commands Sets the timeout value for a named timer. Syntax timerset <timer name> <value> Parameters timerset <timer name> Sets the timer value <value> (60-268400000) for a timer named <value>...
Page 95: Network Firewall Intrusion Prevention System Commands
3-59 Network CLI Commands Reference 3.12 Network Firewall Intrusion Prevention System Commands Network Firewall Commands Displays the firewall Intrusion Prevention System (IPS) submenu. Syntax admin(network.fw)> ips admin(network.fw.ips)> The items available under this command are shown below. Command Description Ref. Sets the IPS parameters page 3-60 show Displays the IPS settings...
Page 96: Set
3-60 WS2000 Wireless Switch System Reference Guide 3.12.1 Network Firewall IPS set Command Network Firewall Intrusion Prevention System Commands Sets the Intrusion Prevention System (IPS) parameters. Syntax set [mode|anomaly-config|signature-categories|direction] set mode [enable|disable] set signature-categorises <category-list> set direction [default|bi-directional] set anomaly-config[-sl <smtplen>|-ml <mimelen>|-md <mimedepth>| -hl <httpline>|-hz <httpsize>|-hlz <httplinesize>| -huz <httpurisize>] mode [enable|disable]...
Page 97 3-61 Network CLI Commands Reference HTTP URI size : 3072 Loaded Signature Categories : TELNET POP3 TCP UDP IMAP HTTP SMTP Packet Direction of signatures : default admin(network.fw.ips)>...
Page 98: Show
3-62 WS2000 Wireless Switch System Reference Guide 3.12.2 Network Firewall IPS show Command show Network Firewall Intrusion Prevention System Commands Displays the Intrusion Prevention System (IPS) configurations. Syntax show all Parameters Displays the IPS configuration. Example admin(network.fw.ips)>show all IPS mode : enable SMTP Header length : 1024...
Page 99 3-63 Network CLI Commands Reference NetBIOS alg : disable HTTP alg : enable admin(network.fw)>...
Page 100: Network Firewall Policy Commands
3-64 WS2000 Wireless Switch System Reference Guide 3.13 Network Firewall Policy Commands policy Network Firewall Commands Displays the firewall policy submenu. Syntax admin(network.fw)> policy admin(network.fw.policy)> NOTE: The Policy menu can only be accessed when Subnet Access Override mode is enabled. To enable Subnet Access Override use the command admin(network.fw)>...
Page 101: Import
3-65 Network CLI Commands Reference 3.13.1 Network Firewall Policy import command import Network Firewall Policy Commands Imports subnet access rules from current subnet access settings created in the GUI interface (Network-> Firewall -> Subnet Access menu item) or using the CLI submap menu commands. Previously set outbound firewall policies will be deleted.
Page 102: Network Firewall Policy Inbound Commands
3-66 WS2000 Wireless Switch System Reference Guide 3.14 Network Firewall Policy Inbound Commands inbound Network Firewall Policy Commands Displays the inbound policy submenu. Syntax admin(network.fw.policy)> inb admin(network.fw.policy.inb)> The items available under this command are shown below. Command Description Ref. Adds a firewall policy. page 3-67 Sets firewall policy parameters.
Page 103: Add
3-67 Network CLI Commands Reference 3.14.1 Network Firewall Policy Inbound add Command Network Firewall Policy Inbound Commands Adds an inbound firewall policy. Syntax add <sip> <netmask> <dip> <dnetmask> Parameters <sip> <netmask> Adds a firewall policy to be effective on communications between a source site <dip>...
Page 104: Delete
3-68 WS2000 Wireless Switch System Reference Guide 3.14.2 Network Firewall Policy Inbound delete Command delete Network Firewall Policy Inbound Commands Deletes a firewall policy. Syntax delete [all|<idx>] Parameters <idx> Deletes inbound firewall policy <idx> from the policy list. Deletes all inbound firewall policies. Example admin(network.fw.policy.inb)>list -------------------------------------------------------------------------...
Page 105: Insert
3-69 Network CLI Commands Reference 3.14.3 Network Firewall Policy Inbound insert Command insert Network Firewall Policy Inbound Commands Inserts a new firewall policy before an existing policy. Syntax insert <idx> <sip> <snetmask> <dip> <dnetmask> Parameters <idx> <sip> Inserts a new policy into the inbound firewall policy list at a specified index. <snetmask>...
Page 106: List
3-70 WS2000 Wireless Switch System Reference Guide 3.14.4 Network Firewall Policy Inbound list Command list Network Firewall Policy Inbound Commands Lists inbound firewall policies. Syntax list {<idx>} Parameters <idx> Displays firewall policy with number <idx>. Example: admin(network.fw.policy.inb)>add 192.168.24.0 255.255.255.0 209.239.170.45 255.255.255.224 Inbound Policy Successfully added at index 1 admin(network.fw.policy.inb)>list -------------------------------------------------------------------------...
Page 107: Move
3-71 Network CLI Commands Reference 3.14.5 Network Firewall Policy Inbound move Command move Network Firewall Policy Inbound Commands Moves a firewall policy to a different position in the list and renumbers all affected items in the list. Syntax move [up|down] <idx> Parameters [up|down] <idx>...
Page 108: Set
3-72 WS2000 Wireless Switch System Reference Guide 3.14.6 Network Firewall Policy Inbound set Command Network Firewall Policy Inbound Commands Sets inbound firewall policy parameters. Syntax set [saddr|daddr|tp|sport}dport|rnat|rport|action|logging] Parameters saddr <idx> <Ip Addr> Sets source IP address <Ip Addr> and IP netmask <netmask> for inbound <netmask>...
Page 109: Network Firewall Policy Outbound Commands
3-73 Network CLI Commands Reference 3.15 Network Firewall Policy Outbound Commands outbound Network Firewall Policy Commands Displays the outbound policy submenu. Syntax admin(network.fw.policy)> outbound admin(network.fw.policy.outbound)> The items available under this command are shown below. Command Description Ref. Adds a firewall policy. page 3-74 Sets firewall policy parameters.
Page 110: Network Firewall Policy Outbound Commands
3-74 WS2000 Wireless Switch System Reference Guide 3.15.1 Network Firewall Policy Outbound add Command Network Firewall Policy Outbound Commands Adds an outbound firewall policy. Syntax add <sip> <netmask> <dip> <netmask> Parameters <sip> <netmask> Adds a firewall policy to be effective on communications between a source site <dip>...
Page 111 3-75 Network CLI Commands Reference 3.15.2 Network Firewall Policy Outbound delete Command delete Network Firewall Policy Outbound Commands Deletes an outbound firewall policy. Syntax delete [all|<idx>] Parameters <idx> Deletes inbound firewall policy <idx> from the policy list. Deletes all outbound firewall policies. Example admin(network.fw.policy.outb)>list -------------------------------------------------------------------------...
Page 112: Insert
3-76 WS2000 Wireless Switch System Reference Guide 3.15.3 Network Firewall Policy Outbound insert Command insert Network Firewall Policy Outbound Commands Inserts a new outbound firewall policy before an existing policy. Syntax insert <idx> <sip> <netmask> <dip> <netmask> Parameters <idx> <sip> Inserts a new policy into the outbound firewall policy list at a specified index.
Page 113: List
3-77 Network CLI Commands Reference 3.15.4 Network Firewall Policy Outbound list Command list Network Firewall Policy Outbound Commands Lists outbound firewall policies. Syntax list {<idx>} Parameters <idx> Displays firewall outbound policy with number <idx>. Example admin(network.fw.policy.outb)>add 192.168.24.0 255.255.255.0 209.239.170.45 255.2 55.255.224 Inbound Policy Successfully added at index 1 admin(network.fw.policy.outb)>list -------------------------------------------------------------------------...
Page 114: Move
3-78 WS2000 Wireless Switch System Reference Guide 3.15.5 Network Firewall Policy Outbound move Command move Network Firewall Policy Outbound Commands Moves an outbound firewall policy up or down in the policy list and renumbers the policy affected by the move. Syntax move [up|down] <idx>...
Page 115: Set
3-79 Network CLI Commands Reference 3.15.6 Network Firewall Policy Outbound set Command Network Firewall Policy Outbound Commands Sets firewall policy parameters. Syntax set [saddr|daddr|tp|sport|dport|nat|action|logging] Parameters saddr <idx> <Ip Addr> Sets source IP address <Ip Addr> and IP netmask <netmask> for outbound <netmask>...
Page 116: Network Firewall Submap Commands
3-80 WS2000 Wireless Switch System Reference Guide 3.16 Network Firewall Submap Commands submap Network Firewall Commands Displays the subnet mapping submenu. Syntax admin(network.fw)> submap admin(network.fw.submap)> NOTE: The submap menu can only be accessed when Subnet Access Override mode is disabled. To disable Subnet Access Override use the command admin(network.fw)>...
Page 117: Add
3-81 Network CLI Commands Reference 3.16.1 Network Firewall Submap add Command Network Firewall Submap Commands Adds subnet access exception rules. Syntax add <from> <to> <name> <tran> <port1> <port2> Parameters add <from> <to> Adds a subnet access exception rule for communication. <name>...
Page 118 3-82 WS2000 Wireless Switch System Reference Guide admin(network.fw.submap)>list s2 ------------------------------------------------------------------------- index from name prot start port end port ------------------------------------------------------------------------- subnet2 subnet3 test3 admin(network.fw.submap)>delete s2 all admin(network.fw.submap)>list s2 ------------------------------------------------------------------------- index from name prot start port end port -------------------------------------------------------------------------...
Page 119: Delete
3-83 Network CLI Commands Reference 3.16.2 Network Firewall Submap delete Command delete Network Firewall Submap Commands Deletes subnet access exception rules. Syntax delete <from> [<idx>|all] Parameters <from> [<idx>|all] • <idx> – Deletes access exception rule entry <idx> from subnet <from> (one = subnet1, = subnet2, = subnet3,...
Page 120: List
3-84 WS2000 Wireless Switch System Reference Guide 3.16.3 Network Firewall Submap list Command list Network Firewall Submap Commands Lists subnet access exception rules. Syntax list <from> Parameters <from> Lists the access exception entries for <from> (one of = subnet1, = subnet2, = subnet3, = subnet4, = subnet5,...
Page 121: Set
3-85 Network CLI Commands Reference 3.16.4 Network Firewall Submap set Command Network Firewall Submap Commands Sets a default subnet access rule to allow or deny communication. Syntax set [default|subnet-logging|logging] Parameters default <from> Sets the default subnet access rule. <to> <rule> •...
Page 122: Show
3-86 WS2000 Wireless Switch System Reference Guide 3.16.5 Network Firewall Submap show Command show Network Firewall Submap Commands Displays default subnet access exception rules for indicated subnet. Syntax show default <from> Parameters default <from> Shows all default access exception rules for subnet <from> (one of = subnet1, subnet2, = subnet3,...
Page 123: Network Lan Commands
3-87 Network CLI Commands Reference 3.17 Network LAN Commands network Displays the LAN submenu. Syntax admin(network)>lan admin(network.lan)> The items available under this command are shown below. Command Description Ref. dhcp Goes to the DHCP submenu. page 3-93 Sets LAN parameters. page 3-88 show Shows LAN parameters.
Page 124: Set
3-88 WS2000 Wireless Switch System Reference Guide 3.17.1 Network LAN set Command Network LAN Commands Sets the LAN parameters for the six subnets. Syntax set [ipadr|mask|dgw|mode|name|port|wlan|stp] set ipadr <idx> <ip> set mask <idx> <netmask> set dgw <idx> <ip> set mode [enable|disable] set name <idx>...
Page 125 3-89 Network CLI Commands Reference admin(network.lan)>set name 1 NewName admin(network.lan)>set port 4 none admin(network.lan)>set wlan 2 s1 admin(network.lan)>show lan 1 subnet name : OfficeN subnet interface : enable ip address : 192.168.0.1 network mask : 255.255.255.0 default gateway : 192.168.0.1 ports : port1 port2 port3 port4 port5 wlan...
Page 126: Show
3-90 WS2000 Wireless Switch System Reference Guide 3.17.2 Network LAN show Command show Network LAN Commands Shows the LAN parameters. Syntax show [lan|stp] Parameters lan <idx> Shows the settings for the subnet <idx> (1–4). Shows the STP status for the device Example admin(network.lan)>show lan 1 subnet name...
Page 127: Updatedns
3-91 Network CLI Commands Reference 3.17.3 Network LAN updateDNS Command updateDNS Network LAN Commands Updates the DNS for the selected subnet. Syntax updateDNS <idx> Parameters <idx> The subnet ID (1-6) Example admin(network.lan)>updateDNS 1 admin(network.lan)> Related Commands updateAllDNS Updates the DNS for all subnets.
Page 128: Updatealldns
3-92 WS2000 Wireless Switch System Reference Guide 3.17.4 Network LAN updateAllDNS Command updateAllDNS Network LAN Commands Updates the DNS for all the active subnets. Syntax updateAllDNS Parameters None Example admin(network.lan)> updateAllDNS admin(network.lan)> Related Commands updateDNS Updates the DNS for a selected subnet.
Page 129: Network Lan Dhcp Commands
3-93 Network CLI Commands Reference 3.18 Network LAN DHCP Commands dhcp Network LAN Commands Displays the DHCP submenu. Syntax admin(network.lan)> dhcp admin(network.lan.dhcp)> The items available under this command are shown below. Command Description Ref. Adds static DHCP address assignments. page 3-94 delete Deletes static DHCP address assignments.
Page 130: Network Lan Dhcp Commands
3-94 WS2000 Wireless Switch System Reference Guide 3.18.1 Network LAN DHCP add Command Network LAN DHCP Commands Adds static DHCP address assignments. Syntax add <idx> <mac> <ip> Parameters <idx> <mac> <ip> Adds a static DHCP address assignment for subnet <idx> (1-6) where the device with the MAC address <mac>...
Page 131 3-95 Network CLI Commands Reference 3.18.2 Network LAN DHCP delete Command delete Network LAN DHCP Commands Deletes static DHCP address assignments. Syntax delete <idx> [<entry>|all] Parameters <idx> [<entry>|all] Deletes static DHCP assignment entries. • <idx> – The subnet index (1-6) •...
Page 132 3-96 WS2000 Wireless Switch System Reference Guide 3.18.3 Network LAN DHCP list Command list Network LAN DHCP Commands Lists static DHCP address assignments. Syntax list <idx> Parameters <idx> Lists the static DHCP address assignments for subnet <idx> (1–6). Example admin(network.lan.dhcp)>add 1 00A0F8F01234 192.168.63.5 admin(network.lan.dhcp)>list 1 ------------------------------------------------------------------------- index mac address...
Page 133: Set
3-97 Network CLI Commands Reference 3.18.4 Network LAN DHCP set Command Network LAN DHCP Commands Sets DHCP parameters for the subnets. Syntax set [dgw|dns|wins|lease|domain|mode|range| relayserverip|ddnsmode|fwdzone|ddnsusrcls| tftp-server|bootfile|option-189|option-43] Parameters dgw <idx> <a.b.c.d> Sets the default gateway for subnet <idx> (1–6) to the IP address <a.b.c.d>.
Page 134 3-98 WS2000 Wireless Switch System Reference Guide option-189 <idx> <ip list> Sets the IP addresses and ports numbers for WIAP enabled switches for the subnet <idx> (1-6). <ip-list> (max 63 characters) must be in the format a.b.c.d:xx and multiple addresses must be separated by comma. option-43 <idx>...
Page 135: Show
3-99 Network CLI Commands Reference 3.18.5 Network LAN DHCP show Command show Network LAN DHCP Commands Shows DHCP parameter settings for specified subnets. Syntax show dhcp <idx> Parameters show dhcp <idx> Displays the DHCP parameter settings for subnet <idx> (1–6). These parameters are set with the set command.
Page 136: Renew
3-100 WS2000 Wireless Switch System Reference Guide 3.18.6 Network LAN DHCP renew Command renew Network LAN DHCP Commands Renews the IP address assigned by DHCP. Syntax renew Parameters None Example admin(network.lan.dhcp)> renew...
Page 137: Network Lan Bridge Commands
3-101 Network CLI Commands Reference 3.19 Network LAN Bridge commands bridge Network LAN Commands Displays the Bridge submenu. Syntax admin(network.lan)> bridge admin(network.lan.bridge)> The items available under this command are shown below. Command Description Ref. show Shows the bridge configuration parameters page 3-102 Sets bridge configuration parameters page 3-104...
Page 138: Show
3-102 WS2000 Wireless Switch System Reference Guide 3.19.1 Network LAN Bridge show Command show Network LAN Bridge commands Displays the bridge configuration parameters. Syntax show Parameters None Example admin(network.lan.bridge)> show admin(network.lan.bridge)>show ** LAN1 Bridge Configuration ** Bridge Priority : 32768 Hello Time (seconds) Message Age Time (seconds) : 20...
Page 139 3-103 Network CLI Commands Reference ** LAN5 Bridge Configuration ** Bridge Priority : 32768 Hello Time (seconds) Message Age Time (seconds) : 20 Forward Delay Time (seconds) : 15 Entry Ageout Time (seconds) : 300 Wireless Trunking : disable ** LAN6 Bridge Configuration ** Bridge Priority : 32768 Hello Time (seconds)
Page 140: Set
3-104 WS2000 Wireless Switch System Reference Guide 3.19.2 Network LAN Bridge set Command Network LAN Bridge commands Sets the bridge configuration parameters. Syntax set [priority|hello|msgage|fwddelay|ageout|wireless-trunking] Parameters priority <LAN-idx> <priority> Sets the bridge priority to <priority> (0-65535) for the lan <LAN- idx>...
Page 141: Network Qos Commands
3-105 Network CLI Commands Reference 3.20 Network QoS Commands network Displays the quality of service (QoS) submenu. Syntax admin(network)> qos admin(network.qos)> The items available under this command are shown below. Command Description Ref. clear Clears QoS parameters. page 3-106 Sets QoS parameters. page 3-107 show Shows QoS parameters.
Page 142: Clear
3-106 WS2000 Wireless Switch System Reference Guide 3.20.1 Network QOS clear Command clear Network QoS Commands Clears QoS radio statistics. Syntax clear queuing Parameters None Example admin(network.qos)>clear queue Related Commands Sets the QoS parameters. show Shows the QoS parameters and the QoS queuing statistics.
Page 143: Set
3-107 Network CLI Commands Reference 3.20.2 Network QOS set Command Network QoS Commands Sets QoS parameters. Syntax set bw-share [mode|weight|threshold] Parameters mode <mode> Set bandwidth share mode <mode> (none, static, weighted or rate-limit) weight <idx> <weight> Set the weight for WLAN <idx> (1–8) to <weight> (1–10).
Page 144: Show
3-108 WS2000 Wireless Switch System Reference Guide 3.20.3 Network QOS show Command show Network QoS Commands Shows QoS parameters and queuing statistics. Syntax show [bw-sharing|queuing] Parameters bw-share Shows the bandwidth sharing settings. queuing Displays the radio QoS queuing statistics. Example admin(network.qos)>show bw BW Share Mode:static admin(network.qos)>show qu 1...
Page 145: Network Router Commands
3-109 Network CLI Commands Reference 3.21 Network Router Commands router network Displays the router submenu. Syntax admin(network)> router admin(network.router)> The items available under this command are shown below. Command Description Ref. Adds user-defined routes. page 3-110 delete Deletes user-defined routes. page 3-111 list Lists user-defined routes.
Page 146: Add
3-110 WS2000 Wireless Switch System Reference Guide 3.21.1 Network Router add Command Network Router Commands Adds user-defined routes. Syntax add <dest> <netmask> <gw> <iface> <metric> Parameters <dest> <netmask> <gw> Adds a route with destination IP address <dest>, IP netmask <iface> <metric> <netmask>, gateway IP address <gw>, interface subnet or WAN set to <iface>...
Page 147: Delete
3-111 Network CLI Commands Reference 3.21.2 Network Routes delete Command delete Network Router Commands Deletes user-defined routes. Syntax delete [all|<idx>] Parameters <idx> Deletes the user-defined route <idx> (1–20) from the list. Deletes all user-defined routes. Example admin(network.router)>list ------------------------------------------------------------------ index destination netmask gateway interface metric ------------------------------------------------------------------ 1 202.57.42.6 255.255.255.224 202.57.42.1 subnet2 3 2 234.44.33.212 255.255.255.234 234.44.33.2 subnet3 5...
Page 148: List
3-112 WS2000 Wireless Switch System Reference Guide 3.21.3 Network Router list Command list Network Router Commands Lists user-defined routes. Syntax list Parameters None Example admin(network.router)>add 234.44.33.212 255.255.255.234 234.44.33.2 s3 5 admin(network.router)>list ------------------------------------------------------------------------- index destination netmask gateway interface metric ------------------------------------------------------------------------- 1 202.57.42.6 255.255.255.224 202.57.42.1 subnet2 3 2 234.44.33.212 255.255.255.234 234.44.33.2 subnet3 5...
Page 149: Set
3-113 Network CLI Commands Reference 3.21.4 Network Router set Command Network Router Commands Sets routing information protocol (RIP) parameters. Syntax set [auth|dir|id|key|passwd|type|dgw-if] Parameters auth <auth> Sets RIP authentication type to <auth> to one of none, simple, or dir <dir> Sets RIP direction to <dir> to one of = receive, = transmit, or both).
Page 150: Show
3-114 WS2000 Wireless Switch System Reference Guide 3.21.5 Network Router show Command show Network Router Commands Shows connected routes and routing information protocol (RIP) parameters. Syntax show [rip|routes] Parameters Shows RIP parameters. routes Shows connected routes. Example admin(network.router)>show rip rip type : off rip direction : both rip authentication type : md5 rip simple auth password : ********...
Page 151: Network Vlan Commands
3-115 Network CLI Commands Reference 3.22 Network VLAN Commands vlan network Displays the VLAN submenu. Syntax admin(network)> vlan admin(network.vlan)> The items available under this command are shown below. Command Description Ref. Sets VLAN parameters. page 3-116 show Shows VLAN parameters. page 3-117 quit Quits the CLI.
Page 152: Set
3-116 WS2000 Wireless Switch System Reference Guide 3.22.1 Network VLAN set Command Network VLAN Commands Sets VLAN parameters. Syntax set [assign-mode|default|vlan-id|trunk-port|allow] Syntax: assign-mode <mode> Assigns the VLAN assignment mode <mode> to one of user or port. default <vlan_id> Assigns the default VLAN ID to <vlan_id>, which is a number between and 4094.
Page 153: Show
3-117 Network CLI Commands Reference 3.22.2 Network VLAN show Command show Network VLAN Commands Shows VLAN parameters. Syntax show [vlan|trunk] Parameters vlan <id> Displays the VLAN settings for the VLAN specified by <id> (1–4094). trunk Displays the Trunk settings. Example admin(network.vlan)>show vlan 3 VLAN assignment mode : user...
Page 154 3-118 WS2000 Wireless Switch System Reference Guide 3.23 Network WAN Commands network Displays the WAN submenu. Syntax admin(network)> wan admin(network.wan)> The items available under this command are shown below. Command Description Ref. Goes to the VPN submenu. page 3-144 Goes to the NAT submenu. page 3-138 Goes to the outbound content filtering submenu.
Page 155: Network Wan Commands
3-119 Network CLI Commands Reference 3.23.1 Network WAN renew Command renew Network WAN Commands Renews the IP address. Syntax renew Parameters None Example admin(network.wan)>renew admin(network.wan)>...
Page 156: Set
3-120 WS2000 Wireless Switch System Reference Guide 3.23.2 Network WAN set Command Network WAN Commands Sets the WAN parameters. In the Web interface, this functionality if provided by the Network->WAN screen. Syntax set [dhcp|dgw|dns|ipadr|mask|mode|ppope|mtu] Parameters dhcp <mode> Enables or disables the switch as a DHCP client. <mode> can be one of enable or disable.
Page 157 3-121 Network CLI Commands Reference admin(network.wan)>set pppoe keepalive enable Related Commands show ip Shows the IP settings for the WAN. show pppoe Shows the PPPoE settings for the WAN.
Page 158: Show
3-122 WS2000 Wireless Switch System Reference Guide 3.23.3 Network WAN show Command show Network WAN Commands Shows the WAN parameters. Syntax show [ip|pppoe|mtuc] Parameters ip <idx> Shows the general IP parameters for the WAN along with settings for the WAN interface associated with <idx>...
Page 159: Network Wan App Commands
3-123 Network CLI Commands Reference 3.24 Network WAN App Commands Network WAN Commands Displays the outbound content filtering submenu. Syntax admin(network.wan)> app admin(network.wan.app)> The items available under this command are shown below. Command Description Ref. addcmd Adds app control commands to the deny list. page 3-124 delcmd Deletes app control commands from the deny list.
Page 160: Addcmd
3-124 WS2000 Wireless Switch System Reference Guide 3.24.1 Network WAN APP addcmd Command addcmd Network WAN App Commands Adds app control commands to the deny list. Syntax addcmd [web|ftp|smtp] Parameters web [file Denies access to the specified web files. <filename>.<ext>| •...
Page 161 3-125 Network CLI Commands Reference admin(network.wan.app)>addcmd ftp put admin(network.wan.app)>addcmd ftp cd admin(network.wan.app)>addcmd ftp pasv admin(network.wan.app)>list ftp FTP Commands Storing Files : deny Retrieving Files : allow Directory List : allow Create Directory : allow Change Directory : deny Passive Operation : deny admin(network.wan.app)>addcmd smtp helo admin(network.wan.app)>addcmd smtp vrfy...
Page 162: Delcmd
3-126 WS2000 Wireless Switch System Reference Guide 3.24.2 Network WAN APP delcmd Command delcmd Network WAN App Commands Deletes application control commands from the deny list. Syntax delcmd [web|ftp|smtp] Parameters web [file Deletes the specified web files from the access denied list. <filename>.<ext>| •...
Page 163 3-127 Network CLI Commands Reference Passive Operation : deny admin(network.wan.app)>delcmd ftp put admin(network.wan.app)>delcmd ftp cd admin(network.wan.app)>list ftp FTP Commands Storing Files : allow Retrieving Files : allow Directory List : allow Create Directory : allow Change Directory : allow Passive Operation : deny admin(network.wan.app)>list smtp SMTP Commands...
Page 164: List
3-128 WS2000 Wireless Switch System Reference Guide 3.24.3 Network WAN APP list Command list Network WAN App Commands Lists the app control records. Syntax list [web|ftp|smtp] Parameters Lists Web/HTTP app control settings. Lists FTP app control settings. smtp Lists SMTP app control record. Example admin(network.wan.app)>list web HTTP Files/Commands...
Page 165: Network Wan Dyndns Commands
3-129 Network CLI Commands Reference 3.25 Network WAN DynDNS Commands dyndns Network WAN Commands Displays the Dynamic DNS menu. DynDNS provides a facility to update the domain name information when the IP address associated with the domain name changes. Syntax admin(network.wan)>...
Page 166: Set
3-130 WS2000 Wireless Switch System Reference Guide 3.25.1 Network WAN DynDNS set Command Network WAN DynDNS Commands Sets the DynDNS parameters Syntax set [mode|username|password|hostname] set mode <mode> set username <username> set password <password> set hostname <hostname> Parameters mode <mode> Enables or disables DynDNS. <mode> can be enable or disable.
Page 167: Show
3-131 Network CLI Commands Reference 3.25.2 Network WAN DynDNS show Command show Network WAN DynDNS Commands Displays the Dynamic DNS parameter information and the current status. Syntax show Parameters None Example admin(network.wan.dyndns)>show DynDNS Configuration Mode : enable Username : JohnDoe Password : ******** Hostname...
Page 168: Update
3-132 WS2000 Wireless Switch System Reference Guide 3.25.3 Network WAN DynDNS update Command update Network WAN DynDNS Commands Manually updates the Dynamic DNS information. Syntax update Parameters None Example admin(network.wan.dyndns)>update IP Address : 192.168.10.1 Hostname : motPropServ...
Page 169: Set
3-133 Network CLI Commands Reference 3.26 Network WAN TrunkIPFPolicy Commands trunkipfpolicy Network WAN Commands Displays the Trunk IP Filter Policy submenu. Syntax admin(network.wan)>trunkipfpolicy admin(network.wan.trunkipfpolicy)> The items available under this command are shown below. Command Description Ref. Adds Trunk Port IP Filter association table entry page 3-134 Removes Trunk Port IP Filter association table entry page 3-135...
Page 170: Add
3-134 WS2000 Wireless Switch System Reference Guide 3.26.1 Network WAN TrunkIPFPolicy add Command Network WAN TrunkIPFPolicy Commands Adds a Trunk Port IP Filter association table entry. Syntax add <filter-name> <direction> <action> Parameters <filter-name> Name of the Trunk Port Filter entry <direction>...
Page 171: Del
3-135 Network CLI Commands Reference 3.26.2 Network WAN TrunkIPFPolicy del Command Network WAN TrunkIPFPolicy Commands Deletes an entry from the Trunk Port IP Filter association table. Syntax del [all|<index>] Parameters Removes all trunk port IP filter association table entries. <index> Remove trunk port ip filter association table entry at the index <index>.
Page 172: Set
3-136 WS2000 Wireless Switch System Reference Guide 3.26.3 Network WAN TrunkIPFPolicy set Command Network WAN TrunkIPFPolicy Commands Sets the different Trunk Port IP Filter Policy configuration settings Syntax set [ipf-mode|default] set ipf-mode <mode> set default [incoming|outgoing] [allow|deny] Parameters ipf-mode <mode> Enables or disables the Trunk Port IP Filtering default Sets the default properties for incoming and outgoing direction to either allow or...
Page 173: Show
3-137 Network CLI Commands Reference 3.26.4 Network WAN TrunkIPFPolicy show Command show Network WAN TrunkIPFPolicy Commands Displays the Trunk Port IP Filter policy configuration information. Syntax show Parameters None Example admin(network.wan.trunkipfpolicy)>show ---------------------------------------------------- Filter-Name Direction Action ---------------------------------------------------- IP Filter Mode : enable Default Incoming Action : allow Default Outgoing Action...
Page 174 3-138 WS2000 Wireless Switch System Reference Guide 3.27 Network WAN NAT Commands Network WAN Commands Displays the nat submenu. Syntax admin(network.wan)> nat admin(network.wan.nat)> The items available under this command are shown below. Command Description Ref. Adds NAT records. page 3-139 delete Deletes NAT records.
Page 175: Network Wan Nat Commands
3-139 Network CLI Commands Reference 3.27.1 Network WAN NAT add Command Network WAN NAT Commands Adds NAT records. Syntax add inb <idx> <name> <tran> <port1> <port2> <ip> <dst_port> Parameters inb <idx> <name> Sets an inbound Network Address Translation (NAT) entry. <tran>...
Page 176: Delete
3-140 WS2000 Wireless Switch System Reference Guide 3.27.2 Network WAN NAT delete Command delete Network WAN NAT Commands Deletes NAT records. Syntax delete inb <idx> [<entry>|all] Syntax: inb <idx> [<entry>|all] Deletes a NAT table entry. • <idx> – The WAN index (1–8) •...
Page 177: List
3-141 Network CLI Commands Reference 3.27.3 Network WAN NAT list Command list Network WAN NAT Commands Lists NAT records. Syntax list inb <idx> Parameters list inb <idx> Lists the inbound NAT entries associated with WAN port <idx> (1–8). Example admin(network.wan.nat)>add inb 2 special tcp 20 21 192.168.42.16 21 admin(network.wan.nat)>list inb 2 ------------------------------------------------------------------------- index...
Page 178: Set
3-142 WS2000 Wireless Switch System Reference Guide 3.27.4 Network WAN NAT set Command Network WAN NAT Commands Sets NAT inbound and outbound parameters. Syntax set [inb|outb|type] Parameters inb [mode|ip] Sets the inbound NAT parameters. • mode <idx> <mode> – Sets the inbound NAT mode for the WAN with index <idx> (1–8).
Page 179: Show
3-143 Network CLI Commands Reference 3.27.5 Network WAN NAT show Command show Network WAN NAT Commands Shows NAT parameters. Syntax show nat <idx> Parameters <idx> show Shows NAT settings for WAN <idx> (1–8). Example admin(network.wan.nat)>set inb mode 1 enable admin(network.wan.nat)>show nat 1 nat type : 1-to-1 one to one nat ip address...
Page 180: Vpn
3-144 WS2000 Wireless Switch System Reference Guide 3.28 Network WAN VPN Commands Network WAN Commands Displays the VPN submenu. Syntax admin(network.wan)> vpn admin(network.wan.vpn)> The items available under this command are shown below. Command Description Ref. cmgr Goes to the cmgr (Certificate Manager) submenu. page 3-156 Adds an security policy database (SPD) entry.
Page 181: Add
3-145 Network CLI Commands Reference 3.28.1 Network WAN VPN add Command Network WAN VPN Commands Adds a security policy database (SPD) entry. Syntax add <name> <LSubnet> <LWANIP> <RSubnetIP> <RSubnetMask> <RGatewayIP> Parameters <name> <LSubnet> <LWanIP> <RSubnetIP> <RSubnetMask> <RGatewayIP> Creates a tunnel named <name> characters) to gain access to local subnet <LSubnet>...
Page 182: Delete
3-146 WS2000 Wireless Switch System Reference Guide 3.28.2 Network WAN VPN delete Command delete Network WAN VPN Commands Deletes security policy database (SPD) entries. Syntax delete [*|<name>] Parameters Deletes all SPD entries. <name> Deletes SPD entries named <name>. Example admin(network.wan.vpn)>list ------------------------------------------------------------------------- Tunnel Name Type...
Page 183: Ikestate
3-147 Network CLI Commands Reference 3.28.3 Network WAN VPN ikestate Command ikestate Network WAN VPN Commands Displays statistics for all active tunnels using Internet Key Exchange (IKE). In particular, the table indicates whether IKE is connected for any of the tunnels, it provides the destination IP address, and the remaining lifetime of the IKE key.
Page 184: List
3-148 WS2000 Wireless Switch System Reference Guide 3.28.4 Network WAN VPN list Command list Network WAN VPN Commands Lists security policy database (SPD) entries. Syntax list {<name>} Parameters Lists all tunnel entries. <name> Lists detailed information about tunnel named <name>. Note that the <name> must match case with the name in the SPD entry.
Page 185: Reset
3-149 Network CLI Commands Reference 3.28.5 Network WAN VPN reset Command reset Network WAN VPN Commands Resets all VPN tunnels. Syntax reset Parameters None Example admin(network.wan.vpn)>reset VPN tunnels reset. admin(network.wan.vpn)>...
Page 186: Set
3-150 WS2000 Wireless Switch System Reference Guide 3.28.6 Network WAN VPN set Command Network WAN VPN Commands Sets security policy database (SPD) entry parameters. Syntax [ike|type|sub|remip|remmask|remgw|authalgo|espauthalgo|enckey|espauthkey| spi| localgw|usepfs|pfsgrp|salife|ipsecdel|auto-initiation| auto-initiate-interval] set ike [myidtype|remidtype|myiddata|opmode|authtype|authalgo|psk| encalgo|lifetime|group] set ike myidtype <name> <idtype> set ike remidtype <name> <idtype> set ike myiddata <name>...
Page 187 3-151 Network CLI Commands Reference set ipsecdel <name> <mode> set auto-initiation <name> <mode> set auto-initiate-interval <interval> Parameters ike myidtype <name> Sets the Local ID type for IKE authentication for SPD <name> characters) <idtype> to <idtype> (one of IP, FQDN, or UFQDN). ike remidtype <name>...
Page 188 3-152 WS2000 Wireless Switch System Reference Guide authkey <name> Sets the AH authentication key (if SPD type is Manual) for tunnel <name> <direction> <authkey> characters) with the direction <direction> set to or OUT, and the manual authentication key set to <authkey>. (The key size is 32 hex characters for MD5, and 40 hex characters for SHA1).
Page 189 3-153 Network CLI Commands Reference Tunnel Type : Manual Remote IP : 206.107.22.45 Remote IP Mask : 255.255.255.224 Remote Security Gateway : 206.107.22.2 Local Security Gateway : 209.239.160.55 AH Algorithm : None Encryption Type : ESP Encryption Algorithm : DES ESP Inbound SPI : 0x00000100 ESP Outbound SPI...
Page 190 3-154 WS2000 Wireless Switch System Reference Guide Detail listing of VPN entry: ------------------------------------------------------------------------ Name : Bob Local Subnet Tunnel Type : Manual Remote IP : 206.107.22.45 Remote IP Mask : 255.255.255.224 Remote Security Gateway : 206.107.22.2 Local Security Gateway : 209.239.160.55 AH Algorithm : MD5 Encryption Type...
Page 191: Stats
3-155 Network CLI Commands Reference 3.28.7 Network WAN VPN stats Command stats Network WAN VPN Commands Lists statistics for all active tunnels. Syntax stats Parameters None Example admin(network.wan.vpn)>stats ------------------------------------------------------------------------ Tunnel Name Status SPI(OUT/IN) Life Time Bytes(Tx/Rx) ------------------------------------------------------------------------ Eng2EngAnnex Not Active Not Active...
Page 192: Network Wan Vpn Cmgr Commands
3-156 WS2000 Wireless Switch System Reference Guide 3.29 Network WAN VPN Cmgr Commands cmgr Network WAN VPN Commands Displays to the Certificate Manager submenu. Syntax admin(network.wan.vpn)> cmgr admin(network.wan.vpn.cmgr)> The items available under this command are shown below. Command Description Ref. genreq Generates a Certificate Request.
Page 193: Delca
3-157 Network CLI Commands Reference 3.29.1 Network WAN VPN Cmgr delca Command delca Network WAN VPN Commands Deletes a trusted certificate. Syntax delca <IDname> Parameters <IDname> Deletes the trusted certificate <IDname>. Example admin(network.wan.vpn.cmgr)>delca CAfinance admin(network.wan.vpn.cmgr)>...
Page 194: Delprivkey
3-158 WS2000 Wireless Switch System Reference Guide 3.29.2 Network WAN VPN Cmgr delprivkey Command delprivkey Network WAN VPN Commands Deletes a private key. Syntax delprivkey <IDName> Parameters <IDname> The key name to be deleted. Example admin(network.wan.vpn.cmgr)>delprivkey <IDname> admin(network.wan.vpn.cmgr)>...
Page 195: Delself
3-159 Network CLI Commands Reference 3.29.3 Network WAN VPN Cmgr delself Command delself Network WAN VPN Cmgr Commands Deletes a self certificate. Syntax delself <IDName> Parameters <IDname> The name of the self certificate to be deleted. Example admin(network.wan.vpn.cmgr)>delself<IDname> admin(network.wan.vpn.cmgr)>...
Page 196: Expcert
3-160 WS2000 Wireless Switch System Reference Guide 3.29.4 Network WAN VPN Cmgr expcert Command expcert Network WAN VPN Cmgr Commands Exports the certificate file. Syntax expcert [ftp|tftp] <filename> Parameters [ftp|tftp] <file name> Exports the certificate with specified filename <file name> by either or tftp.
Page 197: Export-Req
3-161 Network CLI Commands Reference 3.29.5 Network WAN VPN Cmgr export-req Command export-req Network WAN VPN Cmgr Commands Exports the private key ID name to a file. The exported file will be in the same directory as used for importing or exporting configuration files.
Page 198: Genreq
3-162 WS2000 Wireless Switch System Reference Guide 3.29.6 Network WAN VPN Cmgr genreq Command genreq Network WAN VPN Cmgr Commands Generates a Certificate Request. Syntax genreq <IDName> <subject> {-ou <Organization Unit>} {-on <Organization Name>} {-cn <City Name>} {-st <State>} {-p <Postal Code>} {-cc <Country Code>} {-e <Email Address>} { -d <Domain Name>} {-i <IP Address>} {-sa <Signature Algorithm>} {-k <Key Size>} Syntax:...
Page 199: Network Wan Vpn Cmgr Impcert Command
3-163 Network CLI Commands Reference 3.30 Network WAN VPN Cmgr impcert Command impcert Network WAN VPN Cmgr Commands Imports the certificate file. Syntax impcert <type> <filename> Parameters [ftp|tftp] <filename> Imports the certificate with specified filename <file name> by either or tftp. tftp options for this file transfer will use the settings for the configuration file settings.
Page 200: Listca
3-164 WS2000 Wireless Switch System Reference Guide 3.30.1 Network WAN VPN Cmgr listca Command listca Network WAN VPN Cmgr Commands Lists the loaded trusted certificate. Syntax listca Parameters None Example admin(network.wan.vpn.cmgr)>listca Trusted Certificate List:...
Page 201: Listprivkey
3-165 Network CLI Commands Reference 3.30.2 Network WAN VPN Cmgr listprivkey Command listprivkey Network WAN VPN Cmgr Commands Lists the names of private keys. Syntax listprivkey Parameters None Example admin(network.wan.vpn.cmgr)>listprivkey ------------------------------------------------------------------------- Private Key Name Certificate Associated -------------------------------------------------------------------------...
Page 202: Listself
3-166 WS2000 Wireless Switch System Reference Guide 3.30.3 Network WAN Vpn Cmgr listself Command listself Network WAN VPN Cmgr Commands Lists the loaded self certificates. Syntax listself Parameters None Example admin(network.wan.vpn.cmgr)>listself Self Certificate List:...
Page 203: Loadca
3-167 Network CLI Commands Reference 3.30.4 Network WAN VPN Cmgr loadca Command loadca Network WAN VPN Cmgr Commands Loads a trusted certificate from the Certificate Authority. Syntax loadca {ftp <filename>} Parameters loadca Loads the trusted certificate (in PEM format) that is pasted into the command line. ftp <filename>...
Page 204: Loadself
3-168 WS2000 Wireless Switch System Reference Guide 3.30.5 Network WAN VPN Cmgr loadself Command loadself Network WAN VPN Cmgr Commands Loads a self certificate signed by the Certificate Authority. Syntax loadself [<IDname>|ftp <IDname> <filename>] Parameters <IDname> Loads the self certificate signed by the CA with name <IDname>. ftp <IDname>...
Page 205: Showreq
3-169 Network CLI Commands Reference 3.30.6 Network WAN VPN Cmgr showreq Command showreq Network WAN VPN Cmgr Commands Displays a certificate request in PEM format. Syntax showreq <IDname> Parameters showreq Displays a certificate request named <IDname> generated from the genreq command. <IDname>...
Page 206 3-170 WS2000 Wireless Switch System Reference Guide 3.31 Network WLAN Commands wlan network Displays the WLAN submenu. Syntax admin(network)> wlan admin(network.wlan)> The items available under this command are shown below. Command Description Ref. Adds MU access control list entries. page 3-171 delete Deletes MU access control list entries.
Page 207: Network Wlan Commands
3-171 Network CLI Commands Reference 3.31.1 Network WLAN add Command Network WLAN Commands Adds entries to the mobile unit (MU) access control list. Syntax add <idx> <mac1> <mac2> <name> Parameters <idx> <mac1> <mac2> Adds an entry to the MU access control list, where <idx> is the WLAN <name>...
Page 208: Delete
3-172 WS2000 Wireless Switch System Reference Guide 3.31.2 Network WLAN delete Command delete Network WLAN Commands Deletes specified entry or entries from mobile unit (MU) access control list. Syntax delete <idx> [<entry>|all] Parameters <idx> [<entry>|all] Deletes MU ACL entries. • <entry> – Deletes MU access control list entry <entry> (1–30) for WLAN <idx>...
Page 209: List
3-173 Network CLI Commands Reference 3.31.3 Network WLAN list Command list Network WLAN Commands Lists the entries in the mobile unit (MU) access control list. Syntax list <idx> Parameters list <idx> Displays the entries in the MU access control list for WLAN <idx> (1–8). Example admin(network.wlan)>list 1 -------------------------------------------------------------------------...
Page 210: Set
3-174 WS2000 Wireless Switch System Reference Guide 3.31.4 Network WLAN set Command Network WLAN Commands Sets WLAN parameters. Syntax set [acl|adopt|auth|bcast|eap|enc|ess|kerb|mcast|mode|name| vlan-id|no-mu-mu|vop|tkip|ccmp|wep-mcm|mu-inact|wep_shared| handshake-timeout|handshake-retry-count|secure-beacon|enforce-pmk- validation|wireless-stp] set [acl|adopt|bcast] <idx> <mode> set auth <idx> <type> set eap [adv|server|port|syslog|rad-acct|reauth|secret| rad-bind-interface] set eap adv [mu-quite|mu-tx|mu-timeout|mu-retry| server-timeout|server-retry] set eap adv [mu-quite|mu-tx] <idx>...
Page 211 3-175 Network CLI Commands Reference set tkip [key|type|phrase|rotate-mode|interval|wpa2|preauth|pmk] set tkip key <idx> <key> set tkip type <idx> <type> set tkip phrase <idx> <phrase> set tkip [rotate-mode|wpa2|preauth|pmk] <idx> <mode> set tkip interval <idx> <interval> set ccmp [key|type|phrase|rotate-mode|interval|mixed-mode|preauth|opp- pmk] set ccmp key <idx> <key> set ccmp type <idx>...
Page 212 3-176 WS2000 Wireless Switch System Reference Guide eap server <idx> <rsidx> <ip> Sets the RADIUS server <rsidx> (1-primary or 2-secondary) for WLAN <idx> (1–8) to IP address <ip>. eap port <idx> <rsidx> <port> Sets the RADIUS server <rsidx> (1-primary or 2-secondary) for WLAN <idx>...
Page 213 3-177 Network CLI Commands Reference no-mu-mu <idx> <mode> Enables or disables the stoppage of MU-to-MU communication for WLAN <idx> (1–8). vop <idx> <mode> Enables or disables the voice priority mode for WLAN <idx> (1–8). tkip key <idx> <key> Sets the TKIP key to <key> (1–64 hex digits) for WLAN <idx> (1–8). tkip type <idx>...
Page 214 3-178 WS2000 Wireless Switch System Reference Guide handshake-retry-count <idx> Sets the 802.11i handshake retry count to <retry-count> (1-10) for the <retry-count> WLAN <idx> (1–8). This in conjunction with the handshake-timeout command controls the handshake retry time and retry count for those MUs that do not receive EAPOL messages.
Page 215: Show
3-179 Network CLI Commands Reference 3.31.5 Network WLAN show Command show Network WLAN Commands Displays the WLAN parameters. Syntax show [eap|kerb|tkip|ccmp|wep-mcm|wlan|mu-inact|wep_shared|enforce-pmk- validation|wireless-stp] <idx> Syntax: eap <idx> Shows the EAP parameters for WLAN <idx> (1–8). kerb <idx> Shows the Kerberos parameters for WLAN <idx> (1–8). tkip <idx>...
Page 216 3-180 WS2000 Wireless Switch System Reference Guide admin(network.wlan)>show wlan 1 wlan name : WLAN1 ess identifier : 101 wlan mode : enable enc type : none auth type : none voice prioritization : enable disallow mu to mu : disable answer broadcast ess : disable default mu acl mode...
Page 217 3-181 Network CLI Commands Reference 3.32 Network WLAN Rogue AP Commands rogueap Network WLAN Commands Displays the rogue AP submenu. Syntax admin(network.wlan)> rogueap admin(network.wlan.rogueap)> The items available under this command are shown below. Command Description Ref. show Shows current rogue AP configuration. page 3-183 Sets rogue AP parameters.
Page 218: Network Wlan Rogue Ap Commands
3-182 WS2000 Wireless Switch System Reference Guide 3.32.1 Network WLAN Rogueap set Command Network WLAN Rogue AP Commands Sets rogue access point parameters. Syntax set [muscan|apscan|detscan|fullapscan] [mode <mode>|interval <interval>] Parameters [muscan|apscan|detscan|fullapscan] [mode Sets the different Rogue AP parameters <mode>|interval <interval> •...
Page 219: Show
3-183 Network CLI Commands Reference 3.32.2 Network WLAN Rogueap show Command show Network WLAN Rogue AP Commands Shows the current rogue AP configuration. Syntax show Parameters None Example admin(network.wlan.rogueap)>show mu scan : disabled mu scan interval : 60 minutes ap scan : disabled ap scan interval : 60 minutes...
Page 220: Approvedlist
3-184 WS2000 Wireless Switch System Reference Guide 3.33 Network WLAN Rogue AP Approvedlist Commands approvedlist Network WLAN Rogue AP Commands Displays the approved AP list submenu. Syntax admin(network.wlan.rogueap)> approvedlist admin(network.wlan.rogueap.approvedlist)> The items available under this command are shown below. Command Description Ref.
Page 221: Network Wlan Rogue Ap Approvedlist Commands
3-185 Network CLI Commands Reference 3.33.1 Network WLAN Rogueap Approvedlist ageout Command ageoute Network WLAN Rogue AP Approvedlist Commands Displays ageout time for an approved list entry. Syntax ageout <interval> Parameters ageout <interval> Sets the number of minutes, the <interval> (0–1000), before an entry in the approved list is automatically removed.
Page 222: Approve
3-186 WS2000 Wireless Switch System Reference Guide 3.33.2 Network WLAN Rogueap Approvedlist approve Command approve Network WLAN Rogue AP Approvedlist Commands Approves an AP. Syntax approve [<index>|all] Parameters approve • approve <index> – Approves an access point from the list based on the location [<index>|all] specified by <index>.
Page 223: Erase
3-187 Network CLI Commands Reference 3.33.3 Network WLAN Rogueap Approvedlist erase Command erase Network WLAN Rogue AP Approvedlist Commands Erases the approved AP list. Syntax erase all Parameters none Example admin(network.wlan.rogueap.approvedlist)>erase all admin(network.wlan.rogueap.approvedlist)>show approved ap list ++++++++++++++++ approved list ageout : 30 minutes index essid...
Page 224: Show
3-188 WS2000 Wireless Switch System Reference Guide 3.33.4 Network WLAN Rogueap Approvedlist show Command show Network WLAN Rogue AP Approvedlist Commands Shows the approved AP list. Syntax show Parameters None Example admin(network.wlan.rogueap.approvedlist)>show approved ap list ++++++++++++++++ approved list ageout : 30 minutes index essid -----...
Page 225: Network Wlan Rogue Ap Roguelist Commands
3-189 Network CLI Commands Reference 3.34 Network WLAN Rogue AP Roguelist Commands roguelist Network WLAN Rogue AP Commands Displays the rogue AP list submenu. Syntax admin(network.wlan.rogueap)> roguelist admin(network.wlan.rogueap.roguelist)> The items available under this command are shown below. Command Description Ref. show Displays the rogue list entries.
Page 226: Ageout
3-190 WS2000 Wireless Switch System Reference Guide 3.34.1 Network WLAN Rogue AP Roguelist ageout Command ageout Network WLAN Rogue AP Commands Displays the ageout time for a rogue list entry. Syntax ageout <time> Parameters ageout <time> Sets the ageout time for the entry associated to <time> (1–1000) minutes. Example admin(network.wlan.rogueap.roguelist)>ageout 50 Related Commands...
Page 227: Approve
3-191 Network CLI Commands Reference 3.34.2 Network WLAN Rogue AP Roguelist approve Command approve Network WLAN Rogue AP Commands Moves a rogue AP into the approved AP list. Syntax approve [<index>|all] Parameters approve • approve <index> – Puts the rogue AP <index> into the approved AP list. [<index>|all] •...
Page 228: Erase
3-192 WS2000 Wireless Switch System Reference Guide 3.34.3 Network WLAN Rogue AP Roguelist erase Command erase Network WLAN Rogue AP Commands Erases the rogue AP list. Syntax erase all Parameters None Example admin(network.wlan.rogueap.roguelist)>erase all Example show Lists all entries in the rogue AP list.
Page 229: Show
3-193 Network CLI Commands Reference 3.34.4 Network WLAN Rogue AP Roguelist show Command show Network WLAN Rogue AP Commands Displays the rogue list entries. Syntax show [all|<index>|deauth-list] Parameters show Displays Rogue AP lists. [all|<index>|deauth- • all – Displays the complete list of rogue APs. list] •...
Page 230: Set
3-194 WS2000 Wireless Switch System Reference Guide 3.34.5 Network WLAN Rogue AP Roguelist set Command Network WLAN Rogue AP Commands Sets rogue list parameters. Syntax set [rap-containment|deauth-interval|deauth-all] set RAP-Containment <mode> set deauth-interval <interval> set dauth-all <mode> Syntax: RAP-Containment • Enables disables Rogue AP Containment feature.
Page 231: Deauth
3-195 Network CLI Commands Reference 3.34.6 Network WLAN Rogue AP Roguelist deauth Command deauth Network WLAN Rogue AP Commands Manages the Rogue AP Containment list by adding APs, their MAC address to the list and deleting APs from the list. Syntax deauth [add-to-list|add-mac-to-list|remove-from-list] <index>...
Page 232: Network Wlan Rogue Ap Rogue List Locate Commands
3-196 WS2000 Wireless Switch System Reference Guide 3.35 Network WLAN Rogue AP Rogue List Locate Commands locate Network WLAN Rogue AP Roguelist Commands Displays the locate submenu. Syntax admin(network.wlan.rogueap.roguelist)> locate admin(network.wlan.rogueap.roguelist.locate)> The items available under this command are shown below. Command Description Ref.
Page 233: List
3-197 Network CLI Commands Reference 3.35.1 Network WLAN Rogue AP Rogue List Locate list Command list Network WLAN Rogue AP Rogue List Locate Commands Lists the results of the locate rogue AP scan. Syntax list Parameters None Example admin(network.wlan.rogueap.roguelist.locate)>list Related Commands start Starts the rogue AP location process.
Page 234: Start
3-198 WS2000 Wireless Switch System Reference Guide 3.35.2 Network WLAN Rogue AP Rogue List Locate start Command start Network WLAN Rogue AP Rogue List Locate Commands Locates a rogue AP. Syntax start <MAC> <ESSID> Parameters start <MAC> <ESSID> Starts locating a rogue AP where <MAC> is the MAC address (or BSSID) of the rogue AP, and <essid>...
Page 235: Network Wlan Rogue Ap Rogue List Mu Scan Commands
3-199 Network CLI Commands Reference 3.36 Network WLAN Rogue AP Rogue List MU Scan Commands muscan Network WLAN Rogue AP Roguelist Commands Displays the MU scan submenu. Syntax admin(network.wlan.rogueap.roguelist)> muscan admin(network.wlan.rogueap.roguelist.muscan)> The items available under this command are shown below. Command Description Ref.
Page 236: List
3-200 WS2000 Wireless Switch System Reference Guide 3.36.1 Network WLAN Rogue AP Rogue List MU Scan list Command list Network WLAN Rogue AP Roguelist Commands Lists the results of the locate rogue AP scan. Syntax list Parameters None Example admin(network.wlan.rogueap.roguelist.muscan)>list Related Commands start Starts the MU scan process.
Page 237: Start
3-201 Network CLI Commands Reference 3.36.2 Network WLAN Rogue AP Rogue List MU Scan start Command start Network WLAN Rogue AP Roguelist Commands Starts an on-demand MU polling for rogue APs. Syntax start <MAC> <ESSID> Parameters start <MAC> <ESSID> Starts locating a rogue AP where <MAC> is the MAC address (or BSSID) of the rogue AP, and <ESSID>...
Page 238 3-202 WS2000 Wireless Switch System Reference Guide 3.37 Network WLAN Rogue AP Rule List Commands rulelist Network WLAN Rogue AP Commands Displays the rule list submenu. Syntax admin(network.wlan.rogueap)> rulelist admin(network.wlan.rogueap.rulelist)> The items available under this command are shown below. Command Description Ref.
Page 239: Network Wlan Rogue Ap Rule List Commands
3-203 Network CLI Commands Reference 3.37.1 Network WLAN Rogue AP Rule List add Command Network WLAN Rogue AP Rule List Commands Adds an entry to the rule list. Syntax add <MAC> <ESSID> Parameters add <MAC> <ESSID> Adds an entry into the rule list to allow an AP with the mac address <MAC> and the ESSID <ESSID>.
Page 240: Authsymbolap
3-204 WS2000 Wireless Switch System Reference Guide 3.37.2 Network WLAN Rogue AP Rule List authsymbolap Command authsymbolap Network WLAN Rogue AP Rule List Commands Authorizes all Symbol APs. Syntax authsymbolap <mode> Parameters authsymbolap <mode> Enables or disables automatic authorization of all Symbol APs. <mode> can be enable or disable.
Page 241: Delete
3-205 Network CLI Commands Reference 3.37.3 Network WLAN Rogue AP Rule List delete Command delete Network WLAN Rogue AP Rule List Commands Deletes an entry from the rule list. Syntax delete [all|<idx>] Parameters delete [all|<idx>] Deletes entries in the rule list. •...
Page 242: Show
3-206 WS2000 Wireless Switch System Reference Guide 3.37.4 Network WLAN Rogue AP Rule List show Command show Network WLAN Rogue AP Rule List Commands Displays the rule list. Syntax show Parameters None Example admin(network.wlan.rogueap.rulelist)>show rule list +++++++++ symbol ap authorization : enabled index essid...
Page 243: Network Wlan Enhanced Rogue Ap Commands
3-207 Network CLI Commands Reference 3.38 Network WLAN Enhanced Rogue AP Commands enhancedrogueap Network WLAN Commands Displays the Enhanced Rogue AP detection submenu. Syntax admin(network.wlan)> enhancedrogueap admin(network.wlan.enhancedrogueap)> The items available under this command are shown below. Command Description Ref. show Displays the Enhanced Rogue AP parameters.
Page 244: Show
3-208 WS2000 Wireless Switch System Reference Guide 3.38.1 Network WLAN Enhanced Rogue AP show Command show Network WLAN Enhanced Rogue AP Commands Displays the Enhanced Rogue AP parameters. Syntax show Parameters None Example admin(network.wlan.enhancedrogueap)>show Enhanced RAP mode : disabled ERAP scan interval : 10 seconds ERAP scan duration : 100 milli seconds...
Page 245: Set
3-209 Network CLI Commands Reference 3.38.2 Network WLAN Enhanced Rogue AP set Command Network WLAN Enhanced Rogue AP Commands Sets the Enhanced Rogue AP parameters. Syntax set [mode|scaninterval|scanduration|A_channels|BG_channels|erase] set mode <mode> set scaninterval <scaninterval> set scanduration <scanduration> set A_channel {channelset} set BG_channel {channelset} set erase Parameters...
Page 246: Muprobe
3-210 WS2000 Wireless Switch System Reference Guide 3.39 Network WLAN MU Probe Commands muprobe Network WLAN Commands Displays the MU Probe sub menu. Syntax admin(network.wlan)> muprobe admin(network.wlan.muprobe)> The items available under this menu are shown below. Command Description Ref. show Shows the MU Probe Table configuration page 3-211 Sets the MU Probe Table configuration...
Page 247: Show
3-211 Network CLI Commands Reference 3.39.1 Network WLAN MU Probe show Command show Network WLAN MU Probe Commands Displays the MU Probe Table configuration information. Syntax show Parameters None Example admin(network.wlan.muprobe)> show mu probe table : disabled mu probe table size : 200 MUs (number of rows could be more) mu probe window : 30 seconds...
Page 248: Set
3-212 WS2000 Wireless Switch System Reference Guide 3.39.2 Network WLAN MU Probe set Command Network WLAN MU Probe Commands Sets the different MU Probe Table configurations. Syntax set [mode|size|erase|windows] set mode <mode> set size <size> set erase set window <value> Parameters mode <mode>...
Page 249 3-213 Network CLI Commands Reference 3.40 Network WLAN Hotspot Commands hotspot Network WLAN Commands Displays the Hotspot sub menu. Syntax admin(network.wlan)> hotspot admin(network.wlan.hotspot)> The items available under this menu are shown below. Command Description Ref. Sets the hotspot parameters page 3-214 show Displays the hotspot parameters page 3-216...
Page 250: Network Wlan Hotspot Commands
3-214 WS2000 Wireless Switch System Reference Guide 3.40.1 Network WLAN Hotspot set Command Network WLAN Hotspot Commands Sets the different Hotspot parameters. Syntax set [mode|page-loc|exturl|http-mode|hotspot-session-timeout| hotspot-cred-cache] set mode <idx> <mode> set page-loc <idx> <page-loc> set exturl <idx> <page> <url> set http-mode <idx> <http-mode> set hotspot-session-timeout <timeout>...
Page 251 3-215 Network CLI Commands Reference External Fail URL Http Mode : https admin(network.wlan.hotspot)> set mode 1 enable admin(network.wlan.hotspot)> set page-loc 1 url admin(network.wlan.hotspot)> set exturl 1 login //192.168.1.10/wlan1/ hotspt/login.htm admin(network.wlan.hotspot)> set exturl 1 welcome //192.168.1.10/wlan1/ hotspt/welcome.htm admin(network.wlan.hotspot)> set exturl 1 fail //192.168.1.10/wlan1/ hotspt/fail.htm admin(network.wlan.hotspot)>...
Page 252: Show
3-216 WS2000 Wireless Switch System Reference Guide 3.40.2 Network WLAN Hotspot show Command show Network WLAN Hotspot Commands Displays the different hotspot configuration settings. Syntax show [hotspot|white-list|hs-session-timeout|hs-cred-cache] show hotspot <idx> show white-list <idx> Parameters hotspot <idx> Displays the hotspot configuration settings. white-list <idx>...
Page 253: Import
3-217 Network CLI Commands Reference 3.40.3 Network WLAN Hotspot Import Command import Network WLAN Hotspot Commands Imports the html pages for the welcome, login, and fail screens. Syntax import <idx> <page> Parameters import <idx> <page> Imports the specified page for the WLAN with index <idx> (1-8). <page> must be one of login, welcome, or fail.
Page 254: Network Wlan Hotspot Radius Commands
3-218 WS2000 Wireless Switch System Reference Guide 3.41 Network WLAN Hotspot RADIUS commands radius Network WLAN Hotspot Commands Displays the RADIUS server commands for hotspot. RADIUS is used to authenticate hotspot users. Syntax admin(network.wlan.hotspot)> radius admin(network.wlan.hotspot.radius)> The items available under this command are shown below. Command Description Ref.
Page 255: Show
3-219 Network CLI Commands Reference 3.41.1 Network WLAN Hotspot RADIUS show Command show Network WLAN Hotspot RADIUS commands Displays the RADIU ?S server information for each hotspot. Syntax show radius <idx> Parameters show radius <idx> Displays the RADIUS information for the WLAN with the index <idx> (1-8). Example admin(network.wlan.hotspot.radius)>...
Page 256: Set
3-220 WS2000 Wireless Switch System Reference Guide 3.41.2 Network WLAN Hotspot RADIUS set Command Network WLAN Hotspot RADIUS commands Configures the RADIUS server information for hotspots for each WLAN. Syntax set [server|port|secret|acct-mode|acct-timeout|acct-retry| bind-interface|auth-mode] set server <idx> <srvr_type> <ipadr> set port <idx> <srvr_type> <port> set secret <idx>...
Page 257 3-221 Network CLI Commands Reference admin(network.wlan.hotspot.radius)> set secret 1 secondary hello2 admin(network.wlan.hotspot.radius)> set acct-mode 1 enable admin(network.wlan.hotspot.radius)> set acct-timeout 1 90 admin(network.wlan.hotspot.radius)> set acct-retry 1 8 admin(network.wlan.hotspot.radius)> set bind-interface 1 primary s1 admin(network.wlan.hotspot.radius)> set auth-mode 1 PAP admin(network.wlan.hotspot.radius)>show radius 1 Primary Server Ip adr : 192.168.1.222 Primary Server Port...
Page 258: Network Wlan Hotstpot White-List Commands
3-222 WS2000 Wireless Switch System Reference Guide 3.42 Network WLAN Hotstpot White-list Commands white-list Network WLAN Hotspot Commands Displays the White-list submenu. White-list is a list of devices that can use the hotspot. Syntax admin(network.wlan.hotspot)> white-list admin(network.wlan.hotspot.whitelist)> The items available under this command are shown below. Command Description Ref.
Page 259 3-223 Network CLI Commands Reference 3.42.1 Network WLAN Hotspot White-list add Command Network WLAN Hotstpot White-list Commands Adds an entry to the WLAN hotspot white-list. White-list is a list of devices that can access the hotspot. Syntax add rule <wlan_idx> <ipadr> Parameters add rule <wlan_idx>...
Page 260: Clear
3-224 WS2000 Wireless Switch System Reference Guide 3.42.2 Network WLAN Hotspot White-list clear Command clear Network WLAN Hotstpot White-list Commands Clears or deletes the WLAN hotspot white-list entries. Syntax clear rule [all|<wlan_idx> [all|<ipadr>]] clear rule all clear rule <wlan_idx> all clear rule <wlan_idx>...
Page 261: Show
3-225 Network CLI Commands Reference 3.42.3 Network WLAN Hotspot White-list show Command show Network WLAN Hotstpot White-list Commands Displays the WLAN hotspot white-list entries. Syntax show white-rules <idx> Parameters show white-rules <idx> Displays the hotspot white-list for the WLAN with the index <idx> (1-8). Example admin(network.wlan.hotspot.whitelist)>...
Page 262 3-226 WS2000 Wireless Switch System Reference Guide 3.43 Network WLAN WLAN IP Fiter Policy Commands wlanipfpolicy Network WLAN Commands Displays the WLAN IP Filter Policy submenu. Syntax admin(network.wlan)> wlanipfpolicy admin(network.wlan.wlanipfpolicy)> The items available under this command are shown below. Command Description Ref.
Page 263: Network Wlan Wlan Ip Fiter Policy Commands
3-227 Network CLI Commands Reference 3.43.1 Network WLAN WLAN IP Filter Policy set Command Network WLAN WLAN IP Fiter Policy Commands Sets the WLAN IP filter policy configuration. IP Filters have to be set up through the Network > IPFilter menu. Syntax set [ipf-mode|default] set ipf-mode <wlan-idx>...
Page 264: Add
3-228 WS2000 Wireless Switch System Reference Guide 3.43.2 Network WLAN WLAN IP Filter Policy add Command Network WLAN WLAN IP Fiter Policy Commands Adds a new IP Filter association table entry. IP Filters have to be set up through the Network > IPFilter menu. Syntax add <wlan-idx>...
Page 265: Del
3-229 Network CLI Commands Reference 3.43.3 Network WLAN WLAN IP Filter Policy del Command Network WLAN WLAN IP Fiter Policy Commands Deletes a entry from the IP Filter association table. Syntax del <wlan-idx> [all|<index>] Syntax: delete <wlan-idx> Deletes an IP Filter association table entry. The WLAN is specified by the [all|<index>] <wlan-idx>...
Page 266: Show
3-230 WS2000 Wireless Switch System Reference Guide 3.43.4 Network WLAN WLAN IP Filter Policy show Command show Network WLAN WLAN IP Fiter Policy Commands Displays the contents of the IP Filter association table. Syntax show <wlan-idx> Parameters show <wlan-idx> Displays the IP filter association table for the WLAN with the index <wlan-idx> (1-8). Example admin(network.wlan.wlanipfpolicy)>...
Page 267: Network Port Commands
3-231 Network CLI Commands Reference 3.44 Network Port Commands port network Displays the port configuration submenu. Syntax admin(network)>port admin(network.port)> The items available under this command are shown below. Command Description Ref. show Shows the port configuration settings. page 3-233 Sets the port configuration page 3-232 quit Quits the CLI.
Page 268: Set
3-232 WS2000 Wireless Switch System Reference Guide 3.44.1 Network Port set Command Network Port Commands Sets the port configuration parameters. Syntax set [auto-negotiation|speed|duplex] set auto-negotiation <idx> <auto-negotiation> set speed <idx> <speed> set duplex <idx> <duplex> Parameters auto-negotiation Enables or disables auto negotiation. When enabled, the port negotiates the speed <idx>...
Page 269: Show
3-233 Network CLI Commands Reference 3.44.2 Network Port show Command show Network Port Commands Displays the port configuration parameters. Syntax show <idx> Parameters show <idx> Displays the port configuration settings for the port <idx> (port1-port6, wan). Example admin(network.port)> show port1 auto-negotiation : enable speed...
Page 270: Network Ip Filter Commands
3-234 WS2000 Wireless Switch System Reference Guide 3.45 Network IP Filter Commands ipfilter network Displays the IP Filter submenu. IP based filtering allows administrators to configure Incoming and Outgoing IP filtering policies on packets within the same Subnet / WLAN and between wired and wireless hosts. Filters can be set up based on IP Address or as a default rule for all IPs in a given direction.
Page 271: Add
3-235 Network CLI Commands Reference 3.45.1 Network IP Filter add Command Network IP Filter Commands Adds an entry into the global IP Filter table. Syntax add <filter-name> <protocol> <port> <start-src-address> <end-src-address> <start-dest-address> <end-dest-address> Parameters add <filter-name> <protocol> <port> <start-src-address> <end-src-address> <start-dest-address> <end- dest-address>...
Page 272: Del
3-236 WS2000 Wireless Switch System Reference Guide 3.45.2 Network IP Filter del Command Network IP Filter Commands Deletes an entry from the global IP Filter table. Syntax del [all|<idx>] Parameters del [all|<index>] Deletes IP Filter table entries. • del <index> – Deletes the global IP Filter table entry at <index>. •...
Page 273: Show
3-237 Network CLI Commands Reference 3.45.3 Network IP Filter Shlow Command show Network IP Filter Commands Displays the global IP Filter table. Syntax show Parameters None Example admin(network.ipfilter)> show ------------------------------------------------------------------------- Filter-Name Protocol-Port Start-End-Src-IP Start-End-Dst-IP In-Use ------------------------------------------------------------------------- allow_tcp 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 allow_udp 0.0.0.0...
Page 274 3-238 WS2000 Wireless Switch System Reference Guide 3.46 Network WIPS Command wips network Description: Displays the Wireless Intrusion Protection System (WIPS) submenu. Syntax admin(network)> wips admin(network.wips)> The items available under this command are shown below. Command Description Ref. Sets WIPS parameters. page 3-239 show Displays WIPS parameters...
Page 275: Network Wips Command
3-239 Network CLI Commands Reference 3.46.1 Network WIPS set Command Network WIPS Command Enables or disables WIPS. Syntax set mode <mode> Parameters set mode <mode> Enables or disables WIPS. <mode> can be either enable or disable. Example admin(network.wips)> set mode enable admin(network.wips)>...
Page 276: Show
3-240 WS2000 Wireless Switch System Reference Guide 3.46.2 Network WIPS show Command show Network WIPS Command Displays the WIPS parameters. Syntax show [mode|sensor] Parameters mode Enables or disables WIPS mode sensor <mac> Shows sensor configuration <mac> – Shows mac-Sensor MAC address Example admin(network.wips)>...
Page 277: List
3-241 Network CLI Commands Reference 3.46.3 Network WIPS list Command list Network WIPS Command Lists the adopted APs and detected sensors for WIPS. Syntax list [sensors|aps] Parameters list [sensors|aps] • list aps – Lists the sensor APs • list sensors – Lists the discovered APs Example admin(network.wips)>...
Page 278: Convert
3-242 WS2000 Wireless Switch System Reference Guide 3.46.4 Network WIPS convert Command convert Network WIPS Command Converts an existing AP to a dedicated Sensor device. This command is only valid for Motorola AP300. Syntax convert <mac1> <mac2> ... Parameters convert <mac1> <mac2>...
Page 279: Revert
3-243 Network CLI Commands Reference 3.46.5 Network WIPS revert Command revert Network WIPS Command Reverts a dedicated Sensor device to an AP. This command is only valid for Motorola AP300. Syntax revert <mac1> <mac2> ... Syntax: revert <mac1> <mac2> Converts the list of Sensors represented by their MAC addresses <mac1>...
Page 280: Update
3-244 WS2000 Wireless Switch System Reference Guide 3.46.6 Network WIPS update Command update Network WIPS Command Sends configuration information to dedicated sensor devices. Syntax update <mac> <dhcp_mode> <ipaddr> <mask> <dgw> <pwips> {<swips>} Parameters update <mac> <dhcp_mode> <ipaddr> <mask> <dgw> <pwips> {<swips>} Sends the configuration information to the sensor device, where: <mac>...
Page 281: Network Wips Default Commands
3-245 Network CLI Commands Reference 3.47 Network WIPS Default commands defaults Network WIPS Command Goes to the WIPS default configuration menu. Syntax admin(network.wips)>defaults admin(network.wips.defaults)> The items available under this command are shown below. Default Description Ref. show Shows the WIPS default configuration settings. page 3-247 Sets the Sensor default configuration for WIPS.
Page 282: Set
3-246 WS2000 Wireless Switch System Reference Guide 3.47.1 Network WIPS set Command Network WIPS Default commands Sets the default WIPS configuration settings. These settings are used when WIPS configurations are not changed. Syntax set mode <mode> set [ipaddr|mask|dgw|pwips|swips] <a.b.c.d> Syntax: mode <mode>...
Page 283: Show
3-247 Network CLI Commands Reference 3.47.2 Network WIPS show Command show Network WIPS Default commands Displays the default WIPS configuration. Syntax show Parameters None Example admin(network.wips.default)> show DHCP Mode : client IP Address : 192.168.0.10 IP Mask : 255.255.255.0 Default Gateway : 192.168.0.1 Primary WIPS Server : 192.168.0.20...
Page 284: Network Wids Commands
3-248 WS2000 Wireless Switch System Reference Guide 3.48 Network WIDS Commands wids network Displays the Wireless Intrusion Detection System (WIDS) commands. Syntax admin(network)>wids admin(network.wids)> The items available under this command are shown below. Command Description Ref. show Shows WIDS status and statistics page 3-254 Sets WIDS parameters page 3-250...
Page 285: Delete
3-249 Network CLI Commands Reference 3.48.1 Network WIDS delete Command delete Network WIDS Commands Deletes WIDS MU list entries. Syntax delete [all|<idx>] Parameters delete [all|<idx>] • all – Deletes all the MU from the list. • <idx> – Deletes MU list entry at the index <idx>. Example admin(network.wids)>...
Page 286: Set
3-250 WS2000 Wireless Switch System Reference Guide 3.48.2 Network WIDS set Command Network WIDS Commands Sets the WIDPS parameters. Syntax set [mode|detect-window|anomaly-detect|excess-op] set mode <mode> set detect-window <detect-window> set anomaly-mode [mode|filter-ageout] set anomaly-mode mode <violation-type> <mode> set anomaly-mode filter-ageout <type> <filter-ageout> set excess-op [threshold|filter-ageout] set excess-op threshold [mu|radio|switch] <type>...
Page 287 3-251 Network CLI Commands Reference anomaly-detect Configures the anomaly detection mode. [mode|filter- • mode <violation-type> <mode> – Enables or disables anomaly detection for each ageout] violation type <violation-type>. <mode> can be enable or disable. • <violation-type> can be one of the following: •...
Page 288 3-252 WS2000 Wireless Switch System Reference Guide excess-op Sets the threshold of events allowed in the detection window per MU. [threshold|filter- • threshold [mu|radio|switch] <type> <threshold> – Sets the threshold values for mu, ageout] radio, or switch. • <type> is the violation type and can be one of: •...
Page 289 3-253 Network CLI Commands Reference crypto-replay-fails 80211-replay-fails decrypt-fails unassoc-frames eap-starts Anomaly Analysis Status Filter-Ageout (Secs) ---------------- null-dst enabled same-src-dst enabled mcast-src enabled weak-wep-iv enabled tkip-cntr-meas enabled invalid-frame-len enabled...
Page 290: Show
3-254 WS2000 Wireless Switch System Reference Guide 3.48.3 Network WIDS show Command show Network WIDS Commands Displays the default WIDS configuration settings Syntax show [wids|filter] Parameters show [wids|filter] • wids – Displays the default WIDS configuration values. • filter – Displays the filter configuration values. Example admin(network.wids)>...
Page 291 3-255 Network CLI Commands Reference 3.49 Network URL Filter Commands urlfilter network Displays the URL Filter commands Syntax admin(network)> urlfilter admin(network.urlfilter)> The items available under this command are shown below. Command Description Ref. keyword Goes to the Keyword submenu page 3-258 whitelist Goes to the Whitelist submenu page 3-263...
Page 292: Network Url Filter Commands
3-256 WS2000 Wireless Switch System Reference Guide 3.49.1 Network URL Filter set Command Network URL Filter Commands Sets URL FIlter parameters. Syntax set [mode|tcp-port|error-msg|action] set mode <mode> set tcp-port <tcp-port> set error-msg <error-msg> set action <action> Parameters mode <mode> Sets the URL Filter mode. <mode> can be enable or disable.
Page 293: Show
3-257 Network CLI Commands Reference 3.49.2 Network URL Filter show Command show Network URL Filter Commands Displays URL Filter configuration information. Syntax show Parameters None Example admin(network.urlfilter)>show URL Filter Mode : Disable TCP Port Number : 80 Error Message : policies of your service provider Action on DNSRD reply failure : deny...
Page 294 3-258 WS2000 Wireless Switch System Reference Guide 3.50 Network URL Filter Keyword Commands keyword Network URL Filter Commands Displays the URL Filter Keyword commands. Syntax admin(network.urlfilter)> keyword admin(network.urlfilter.keyword)> The items available under this command are shown below. Command Description Ref. Adds a new keyword and action to the keyword filter table page 3-259 delete...
Page 295: Network Url Filter Keyword Commands
3-259 Network CLI Commands Reference 3.50.1 Network URL Filter Keyword add Command Network URL Filter Keyword Commands Adds a new keyword and action to the keyword filter table. Syntax add <keyword> <action> Parameters add <keyword> Adds a filter to the keyword filter table. <action>...
Page 296: Delete
3-260 WS2000 Wireless Switch System Reference Guide 3.50.2 Network URL Filter Keyword delete Command delete Network URL Filter Keyword Commands Deletes a keyword from the keyword table. Syntax delete <keyword> Parameters delete <keyword> Deletes the keyword <keyword> from the URL Filter keyword table. Example admin(network.urlfilter.keyword)>show --------URL FILTERING KEYWORD DETAILS---------...
Page 297: Removeall
3-261 Network CLI Commands Reference 3.50.3 Network URL Filter Keyword removeall Command removeall Network URL Filter Keyword Commands Removes all entries from the Keyword Table. Syntax removeall Parameters None Example admin(network.urlfilter.keyword)>show --------URL FILTERING KEYWORD DETAILS--------- KeyWord Action share Deny trading Deny stocks Deny...
Page 298: Show
3-262 WS2000 Wireless Switch System Reference Guide 3.50.4 Network URL Filter Keyword show Command show Network URL Filter Keyword Commands Displays the URL filter keyword table entries. Syntax show Parameters None Example admin(network.urlfilter.keyword)>show --------URL FILTERING KEYWORD DETAILS--------- KeyWord Action share Deny trading Deny...
Page 299: Network Url Filter White List Commands
3-263 Network CLI Commands Reference 3.51 Network URL Filter White list Commands whitelist Network URL Filter Commands Displays the whitelist URLs commands. Syntax admin(network.urlfilter)> whitelist admin(network.urlfilter.whitelist)> The items available under this command are shown below. Command Description Ref. Adds a whitelist entry to the URL whitelist table. page 3-264 delete Deletes a whitelist entry from the URL whitelist table.
Page 300: Add
3-264 WS2000 Wireless Switch System Reference Guide 3.51.1 Network URL Filter White List add Command Network URL Filter White list Commands Adds a new whitelist entry to the whitelist table. Syntax add <whitelist> Parameters add <whitelist> Adds a whitelist entry into the whitelist table. <whitelist> is an URL to be added. Example admin(network.urlfilter.whitelist)>show --------URL FILTERING WHITE LIST DETAILS---------...
Page 301: Delete
3-265 Network CLI Commands Reference 3.51.2 Network URL Filter White List delete Command delete Network URL Filter White list Commands Deletes a whitelist entry from the whitelist table. Syntax delete [<whitelist>|all] Parameters delete Deletes the entries from the URL whitelist table. [<whitelist>|all] <whitelist>...
Page 302: Show
3-266 WS2000 Wireless Switch System Reference Guide 3.51.3 Network URL Filter White List show Command show Network URL Filter White list Commands Displays the URL filter whitelist table entries. Syntax show Parameters None Example admin(network.urlfilter.whitelist)>show --------URL FILTERING WHITE LIST DETAILS--------- mot.com moto.com admin(network.urlfilter.whitelist)>...
Page 303 3-267 Network CLI Commands Reference 3.52 Network URL Filter Black List Commands blacklist Network URL Filter Commands Displays the URL Filter black list URLs commands. Syntax admin(network.urlfilter)> blacklist admin(network.urlfilter.blacklist)> The items available under this command are shown below. Command Description Ref.
Page 304: Network Url Filter Black List Commands
3-268 WS2000 Wireless Switch System Reference Guide 3.52.1 Network URL Filter Black List add Command Network URL Filter Black List Commands Adds a new blacklist entry to the blacklist table. Syntax add <blacklist> Parameters add <blacklist> Adds a blacklist entry into the blacklist table. <blacklist> is an URL. Example admin(network.urlfilter.blacklist)>show --------URL Filtering BLACK LIST DETAILS---------...
Page 305: Delete
3-269 Network CLI Commands Reference 3.52.2 Network URL Filter Black List delete Command delete Network URL Filter Black List Commands Deletes a blacklist entry from the blacklist table. Syntax delete [<blacklist>|all] Parameters Deletes the entries from the URL blacklist table. [<blacklist>|all] <blacklist>...
Page 306: Show
3-270 WS2000 Wireless Switch System Reference Guide 3.52.3 Network URL Filter Black List show Command show Network URL Filter Black List Commands Displays the URL filter blacklist table entries. Syntax show Parameters None Example admin(network.urlfilter.blacklist)>show --------URL Filtering BLACK LIST DETAILS--------- shares.com trading.com admin(network.urlfilter.blacklist)>...
Page 307: Network Url Filter Trusted Ip Commands
3-271 Network CLI Commands Reference 3.53 Network URL Filter Trusted IP Commands trustip Network URL Filter Commands Displays the URL Trusted IP commands. Syntax admin(network.urlfilter)> trustip admin(network.urlfilter.trustip)> The items available under this command are shown below. Command Description Ref. Adds an IP to the trusted IP list page 3-272 delete Deletes an IP from the trusted IP list...
Page 308: Add
3-272 WS2000 Wireless Switch System Reference Guide 3.53.1 Network URL Filter Trusted IP add Command Network URL Filter Trusted IP Commands Adds a new IP into the trusted IP table. add <trustip> Parameters add <trustip> Adds an IP address <trustip> into the trusted IPs list. Example admin(network.urlfilter.trustip)>show --------URL FILTERING TRUST IP---------...
Page 309: Delete
3-273 Network CLI Commands Reference 3.53.2 Network URL Filter Trusted IP delete Command delete Network URL Filter Black List Commands Deletes an entry from the trusted IPs list. Syntax delete [<trustip>|all] Parameters del [<trustip>|all] Deletes trusted IP entries from the trusted IP list. <trustedip>...
Page 310: Show
3-274 WS2000 Wireless Switch System Reference Guide 3.53.3 Network URL Filter Trusted IP show Command show Network URL Filter Trusted IP Commands Displays the trusted IPs list Syntax show Parameters None Example admin(network.urlfilter.trustip)>show --------URL FILTERING TRUST IP--------- 192.168.10.20 192.168.10.10 admin(network.urlfilter.trustip)>...
Page 311: Chapter 4: System Cli Commands Reference
System CLI Commands Reference System commands are used to set the system parameters for the WS 2000 Wireless Switch. 4.1 system Admin Menu Commands Use the command to go to the System menu. system admin> system admin(system)> The following commands are available under the System menu: Command Description Ref.
Page 312: Lastpw
4-2 WS2000 Wireless Switch System Reference Guide 4.1.1 System lastpw Command lastpw system This command displays the MAC address for the switch, the previous admin password for the switch, and the number of times the current admin password has been used along with how many more times it will be valid.
Page 313: Exec
System CLI Commands Reference 4.1.2 System exec Command exec system Executes a linux command Syntax exec <command> Parameters exec <command> Executes a linux command <command>. Example admin(system)> exec df -h /mnt Filesystem Size Used Avail Use% Mounted on automount(pid153) /mnt...
Page 314: System Authentication Commands
4-4 WS2000 Wireless Switch System Reference Guide 4.2 System Authentication Commands authentication system Displays the authentication submenu. Syntax admin(system)> authentication admin(system.authentication)> The items available under this command are shown below. Command Description Ref. radius Goes to the RADIUS submenu. page 4-7 Sets the mode.
Page 315: Set
System CLI Commands Reference 4.2.1 System Authentication set Command System Authentication Commands Sets the parameter that specifies how user authentication is taking place. Syntax set [mode|auth-loc] [local|radius] Syntax: set mode [local|radius] Sets the authentication mode. If set to local, the internal User Database will serve as the data source.
Page 316: Show
4-6 WS2000 Wireless Switch System Reference Guide 4.2.2 System Authentication show Command show System Authentication Commands Shows the main user authentication parameters. Syntax show all Parameters None Example admin(system.authentication)>set mode local admin(system.authentication)>show all authentication mode : local radius user location and type : radius admin(system.authentication)>...
Page 317: System Authentication Radius Commands
System CLI Commands Reference 4.3 System Authentication RADIUS Commands radius System Authentication Commands Displays the RADIUS submenu. Syntax admin(system.authentication)> radius admin(system.authentication.radius)> The items available under this command are shown below. Command Description Ref. Sets the RADIUS authentication parameters. page 4-8 show Shows the RADIUS authentication parameters.
Page 318: Set
4-8 WS2000 Wireless Switch System Reference Guide 4.3.1 System Authentication RADIUS set Command System Authentication RADIUS Commands Sets the RADIUS proxy server authentication parameters. Syntax set [auth-server-ip|auth-server-port|shared-secret] set auth-server-ip <IP> set auth-server-port <port> set shared-secret <password> Parameters set auth-server-ip <IP> Sets the IP address for the RADIUS authentication proxy server to the IP address <IP>.
Page 319: Show
System CLI Commands Reference 4.3.2 System Authentication RADIUS show Command show System Authentication RADIUS Commands Shows the RADIUS authentication parameters. Syntax show all Parameters None Example admin(system.authentication.radius)> set auth-server-ip 192.168.0.4 admin(system.authentication.radius)> set auth-server-port 1812 admin(system.authentication.radius)> set shared mysecret admin(system.authentication.radius)>show all radius server ip : 192.168.0.4 radius server port...
Page 320 4-10 WS2000 Wireless Switch System Reference Guide 4.4 System Configuration Commands config system Displays the config submenu. Syntax admin(system)> config admin(system.config)> The items available under this command are shown below. Command Description Ref. default Restores default configuration page 4-11 export Exports configuration from the system page 4-12 import...
Page 321: System Configuration Commands
4-11 System CLI Commands Reference 4.4.1 System Config default Command default System Configuration Commands Restores the switch to the factory default configuration. Syntax default Parameters None Example admin(system.config)>default Are you sure you want to default the configuration? (yes/no):yes ************************************************************************* System will now restore default configuration. You will need to set the country code for correct operation.
Page 322: Export
4-12 WS2000 Wireless Switch System Reference Guide 4.4.2 System Config export Command export System Configuration Commands Exports the configuration from the system. Syntax export [ftp|tftp|terminal|sftp] Syntax: export Exports the system configuration. [ftp|tftp|terminal • ftp – Exports the configuration to the FTP server. Use the set command to set the sftp] server, user, password, and file name before using this command.
Page 323 4-13 System CLI Commands Reference // WS2000 menu set name WS2000 set loc Extra\20office set email fred@symbol.com set cc us set airbeam mode disable set airbeam enc-passwd a11e00942773 set applet lan enable set applet wan enable set applet slan enable set applet swan enable set cli lan enable set cli wan enable...
Page 324: Import
4-14 WS2000 Wireless Switch System Reference Guide 4.4.3 System Config import Command import System Configuration Commands Imports the configuration to the system. Syntax import [ftp|tftp|sftp] {default-and-apply} Parameters import [ftp|tftp] Imports configuration from external devices. {default-and-apply} • ftp – Imports the configuration from the FTP server. Use the set command to set the server, user, password, and file.
Page 325: Partial
4-15 System CLI Commands Reference 4.4.4 System Config partial Command partial System Configuration Commands Resets the switch's configuration to the factory default settings for all settings except the WAN and some SNMP related settings. The following settings will remain intact when using Restore Partial Default Configuration: •...
Page 326: Set
4-16 WS2000 Wireless Switch System Reference Guide 4.4.5 System Config set Command System Configuration Commands Sets the import/export parameters. Syntax set [server|user|passwd|file|cfgpath|fw|sensor-fw|import-enc-password| bind-interface|ap300] set server <IP> set user <username> set passwd <password> set file <filename> set cfgpath <filepath> set fw [file|path|boot|active-partition] set fw file <filename>...
Page 327 4-17 System CLI Commands Reference sensor-fw [ Sets sensor firmware information. file <filename>| • file <filename> – Sets the sensor firmware file name to <filename> (up to path <path| characters). max-size <size>] • path <path> – Sets the firmware file path for the sensor to <path> (up to characters).
Page 328: Show
4-18 WS2000 Wireless Switch System Reference Guide 4.4.6 System Config show Command show System Configuration Commands Shows the import/export parameters. Syntax show all Parameters None Example admin(system.config)> show all ftp/tftp server ip address : 157.235.208.196 ftp user name : admin ftp password : ******** cfg filename...
Page 329: Update
4-19 System CLI Commands Reference 4.4.7 System Config update Command update System Configuration Commands Performs a firmware update. Syntax update <mode> {<interface>} update [tftp|ftp|sftp] <interface> update cf Parameters update [tftp|ftp|sftp] Sets how firmware updates will occur. Select between ftp, sftp and tftp.
Page 330: Sensor-Fw-Update
4-20 WS2000 Wireless Switch System Reference Guide 4.4.8 System Config sensor-fw-update Command sensor-fw-update System Configuration Commands Performs firmware update for the sensors. When sensor firmware update is done, • No restart is required. • New sensors receive the updated firmware. •...
Page 331: Loadtocf
4-21 System CLI Commands Reference 4.4.9 System Config loadtocf Command loadtocf System Configuration Commands This command loads and updates the firmware to the CF card. This is used for dual boot. Syntax loadtocf [cf|ftp|tftp|sftp] <image-type> Syntax: cf <image-type> Loads the image to the CF card. The <image-type> (primary, secondary) is the target partition on the CF card to store the image on.
Page 332 4-22 WS2000 Wireless Switch System Reference Guide 4.5 System Logs Commands logs system Displays the logs submenu. Syntax admin(system)> logs admin(system.logs)> The items available under this command are shown below. Command Description Ref. delete Deletes core files. page 4-23 Sets log options and parameters. page 4-25 send Sends log and core files.
Page 333: System Logs Commands
4-23 System CLI Commands Reference 4.5.1 System Logs delete Command delete System Logs Commands Deletes the core log files. Syntax delete Parameters None Example admin(system.logs)>delete...
Page 334: Send
4-24 WS2000 Wireless Switch System Reference Guide 4.5.2 System Logs send Command send System Logs Commands Sends log and core files through FTP to a location specified with the command. Use the command to set the FTP login and site information first. Syntax send Parameters...
Page 335: Set
4-25 System CLI Commands Reference 4.5.3 System Logs set Command System Logs Commands Sets log options and parameters. Syntax set [ipadr|level|mode|cf_logging_mode|server|user|passwd] set ipadr <ip> set level <level> set mode <mode> set cf_logging_mode <mode> set server <ip> set user <username> set passwd <password> Parameters ipadr <ip>...
Page 336: Show
4-26 WS2000 Wireless Switch System Reference Guide 4.5.4 System Logs Show Command show System Logs Commands Shows logging options. Syntax show all Parameters None Example admin(system.logs)>set user user1 admin(system.logs)>set passwd hello admin(system.logs)>show all log level : L4 Warning ext syslog server logging : enable syslog server logging on CF : disable...
Page 337: View
4-27 System CLI Commands Reference 4.5.5 System Logs View Command view System Logs Commands Views the system log file. Syntax view Parameters None Example admin(system.logs)>view 7 16:14:00 (none) syslogd 1.4.1: restart (remote reception). 7 16:14:10 (none) klogd: :ps log:fc: queue maintenance 7 16:14:41 (none) klogd: :ps log:fc: queue maintenance 7 16:15:43 (none) last message repeated 2 times 7 16:16:01 (none) CC:...
Page 338 4-28 WS2000 Wireless Switch System Reference Guide 4.6 System NTP Commands system Displays the NTP submenu. Syntax admin(system)> ntp admin(system.ntp)> The items available under this command are shown below. Command Description Ref. show Shows NTP parameters settings. page 4-30 Sets NTP parameters. page 4-29 date-zone Shows the date, time and time zone...
Page 339: System Ntp Commands
4-29 System CLI Commands Reference 4.6.1 System NTP Set Command System NTP Commands Sets NTP parameters. Syntax set [mode|intrvl|server|port|time|zone] set mode <mode> set intrvl <interval> set server <idx> <ip/hostname> set port <idx> <port> set time <yyyy> <MM> <dd> <hh> <mm> <ss> set zone <zone-index>...
Page 340: Show
4-30 WS2000 Wireless Switch System Reference Guide 4.6.2 System NTP Show Command show System NTP Commands Shows all NTP server settings. Syntax show all Parameters None Example admin(system.ntp)>show all ntp mode : enable server ip 1 : 114.233.112.4 server ip 2 : 0.0.0.0 server ip 3 : 0.0.0.0...
Page 341: Date-Zone
4-31 System CLI Commands Reference 4.6.3 System NTP Date-zone Command date-zone System NTP Commands Shows the WS2000 date, time and time zone. Syntax date-zone Parameters None Example admin(system.ntp)> date-zone Date/Time : Thu 1970-Jan-01 05:53:25 +0530 IST Time Zone : Asia/Calcutta admin(system.ntp)>...
Page 342: Zone-List
4-32 WS2000 Wireless Switch System Reference Guide 4.6.4 System NTP zone-list Command zone-list System NTP Commands Displays the different time zones. Syntax zone-list Parameters None Example admin(system.ntp)>zone-list ---------------------------------------------- Index | TimeZone ---------------------------------------------- | Africa/Abidjan | Africa/Accra | Africa/Addis_Ababa | Africa/Algiers | Africa/Asmera | Africa/Bamako | Africa/Bangui...
Page 343: System Radius Commands
4-33 System CLI Commands Reference 4.7 System RADIUS Commands radius system Displays the RADIUS submenu. Syntax admin(system)> radius admin(system.radius)> The items available under this command are shown below. Command Description Ref. Goes to the EAP submenu. page 4-41 policy Goes to the access policy submenu. page 4-57 ldap Goes to the LDAP submenu.
Page 344: Generate-Dh-Param
4-34 WS2000 Wireless Switch System Reference Guide 4.7.1 System RADIUS generate-dh-param Command generate-dh-param System RADIUS Commands Generates the DH Params file for supporting Cipher Suit v 0x13 (TLS_DHE_DSS_WITH_3DES_EDE_CBC_SHA) for EAP-TLS./TTLS protocols. If this file does not exist when the WS2000 is booted, it is created. This command provides a facility to create the DH Params file as required.
Page 345: Set
4-35 System CLI Commands Reference 4.7.2 System RADIUS set Command System RADIUS Commands Sets the RADIUS database to either the local database or an LDAP server. Syntax set database [local|ldap|ldaps] Parameters set database Sets the RADIUS server to the local database (local) or an LDAP server (ldap) or [local|ldap|ldaps] a secured LDAP server (ldaps).
Page 346: Show
4-36 WS2000 Wireless Switch System Reference Guide 4.7.3 System RADIUS show Command show System RADIUS Commands Shows the RADIUS parameters. Syntax show all Parameters None Example admin(system.radius)>set database ldap admin(system.radius)>show all Database : ldap Related Commands Sets the RADIUS database source.
Page 347: System Radius Client Commands
4-37 System CLI Commands Reference 4.8 System RADIUS Client Commands client System RADIUS Commands Displays the client submenu. Syntax admin(system.radius)>client admin(system.radius.client)> The items available under this command are shown below. Command Description Ref. Adds a RADIUS client. page 4-38 Deletes a RADIUS client. page 4-39 show Displays a list of configured clients.
Page 348: Add
4-38 WS2000 Wireless Switch System Reference Guide 4.8.1 System RADIUS Client add Command System RADIUS Client Commands Adds a RADIUS client. Syntax add <ip> <mask> <secret> Parameters add <ip> <mask> <secret> Adds a RADIUS client with IP address <ip>, netmask <mask>, and shared secret <secret>.
Page 349: Del
4-39 System CLI Commands Reference 4.8.2 System RADIUS Client del Command System RADIUS Client Commands Deletes a RADIUS client with the provided IP address. Syntax del <ip> Parameters del <ip> Deletes the RADIUS client with IP address <ip>. Example admin(system.radius.client)>show List of Radius Clients ------------------------------------------------------------------------- Subnet/Host...
Page 350: Show
4-40 WS2000 Wireless Switch System Reference Guide 4.8.3 System RADIUS Client show Command show System RADIUS Client Commands Displays a list of configured RADIUS clients. Syntax show Parameters None Example admin(system.radius.client)>show List of Radius Clients ------------------------------------------------------------------------- Subnet/Host Netmask SharedSecret ------------------------------------------------------------------------- 192.168.46.4 225.225.225.0 ******...
Page 351 4-41 System CLI Commands Reference 4.9 System RADIUS EAP Commands System RADIUS Commands Displays the EAP submenu. Syntax admin(system.radius)> eap admin(system.radius.eap)> The items available under this command are shown below. Command Description Ref. peap Goes to the PEAP submenu. page 4-45 ttls Goes to the TTLS submenu.
Page 352: System Radius Eap Commands
4-42 WS2000 Wireless Switch System Reference Guide 4.9.1 System RADIUS EAP import Command import System RADIUS EAP Commands Imports the EAP certificates. Syntax import [server|cacert] <cert ID> Parameters server <cert id> Imports a server certificate with the certificate ID <cert id>. cacert <cert id>...
Page 353: Set
4-43 System CLI Commands Reference 4.9.2 System RADIUS EAP set Command System RADIUS EAP Commands Sets the EAP parameters. To configure each of the selected authentication types, go to the submenu associated with each type. Syntax set auth [peap|ttls|both] Parameters auth [peap|ttls|both] Sets the default authorization type to one of PEAP...
Page 354: Show
4-44 WS2000 Wireless Switch System Reference Guide 4.9.3 System RADIUS EAP show Command show System RADIUS EAP Commands Displays the EAP parameters. Syntax show [all|cert] Parameters show [all|cert] Displays EAP parameters • all – Displays the default EAP authentication settings. •...
Page 355: System Radius Eap Peap Commands
4-45 System CLI Commands Reference 4.10 System RADIUS EAP PEAP Commands peap System RADIUS EAP Commands Displays the PEAP submenu. Syntax admin(system.radius.eap)> peap admin(system.radius.eap.peap)> The items available under this command are shown below. Command Description Ref. Sets the PEAP authentication type. page 4-46 show Shows the PEAP authentication type.
Page 356: Set
4-46 WS2000 Wireless Switch System Reference Guide 4.10.1 System RADIUS EAP PEAP set Command System RADIUS EAP PEAP Commands Sets the PEAP authentication type. Syntax set auth <peap type> Parameters set auth <peap type> Sets the authentication type for PEAP to <peap type> (GTC or MTCHAPv2).
Page 357: Show
4-47 System CLI Commands Reference 4.10.2 System RADIUS EAP PEAP show Command show System RADIUS EAP PEAP Commands Displays the PEAP authentication type. Syntax show Parameters None Example admin(system.radius.eap.peap)>set auth gtc admin(system.radius.eap.peap)>show PEAP Auth Type : gtc Related Commands Sets the PEAP authentication type.
Page 358: System Radius Eap Ttls Commands
4-48 WS2000 Wireless Switch System Reference Guide 4.11 System RADIUS EAP TTLS Commands ttls System RADIUS EAP Commands Displays the TTLS submenu. Syntax admin(system.radius.eap)> ttls admin(system.radius.eap.ttls)> The items available under this command are shown below. Command Description Ref. Sets the TTLS authentication type. page 4-49 show Shows the TTLS authentication type.
Page 359: Set
4-49 System CLI Commands Reference 4.11.1 System RADIUS EAP TTLS set Command System RADIUS EAP TTLS Commands Sets the TTLS authentication type. Syntax set auth <ttls type> Parameters set auth <auth type> Sets the authentication type for TTLS to <auth type> (PAP, MD5, or MSCHAPv2).
Page 360: Show
4-50 WS2000 Wireless Switch System Reference Guide 4.11.2 System RADIUS EAP TTLS show Command show System RADIUS EAP TTLS Commands Shows the TTLS authentication type. Syntax show Parameters None Example admin(system.radius.eap.ttls)>set auth md5 admin(system.radius.eap.ttls)>show TTLS Auth Type : md5 Related Commands Sets the TTLS authentication type.
Page 361 4-51 System CLI Commands Reference 4.12 System RADIUS LDAP Commands ldap System RADIUS Commands Displays the LDAP submenu. Syntax admin(system.radius)> ldap admin(system.radius.ldap)> The items available under this command are shown below. Command Description Ref. Sets the LDAP parameters. page 4-52 show Shows the LDAP parameters.
Page 362: System Radius Ldap Commands
4-52 WS2000 Wireless Switch System Reference Guide 4.12.1 System RADIUS LDAP set Command System RADIUS LDAP Commands Sets the LDAP parameters. Syntax set [ipadr|domain|port|binddn|basedn|passwd|login|pass_attr| groupname|filter|membership|adagent|pri-domain|admin-uname|admin-pass] set ipadr <ip> set domain <domain> set port <port> set binddn <binddn> set basedn <basedn> set passwd <password>...
Page 363 4-53 System CLI Commands Reference Example admin(system.radius.ldap)>set ipadr 192.168.42.23 admin(system.radius.ldap)>set port 356 admin(system.radius.ldap)>show all LDAP Server IP : 192.168.42.23 LDAP Server Port : 56 LDAP Bind DN : dfkjkkj LDAP Base DN : o=mobion LDAP Login Attribute : (uid=%{Stripped-User-Name:-%{User- Name}}) LDAP Password Attribute : userPassword LDAP Group Name Attribute...
Page 364: Show
4-54 WS2000 Wireless Switch System Reference Guide 4.12.2 System RADIUS LDAP show Command show System RADIUS LDAP Commands Description: Displays the LDAP parameters. Syntax show all Parameters None Example admin(system.radius.ldap)>set ipadr 192.168.42.23 admin(system.radius.ldap)>set port 356 admin(system.radius.ldap)>show all LDAP Server IP : 192.168.42.23 LDAP Server Port : 56...
Page 365: Import
4-55 System CLI Commands Reference 4.12.3 System RADIUS LDAP import Command import System RADIUS LDAP Commands Imports Secure LDAP certificates. Syntax import [client|cacert] <cert-id> Parameters import Import Secure LDAP certificates. [client|cacert] • client – Imports self certificate <cert-id> <cert-id> • ca-cert – Imports the trusted certificate authority certificate <cert-id> Example admin(system.radius.ldap)>...
Page 366: Join
4-56 WS2000 Wireless Switch System Reference Guide 4.12.4 System RADIUS LDAP join Command join System RADIUS LDAP Commands Joins the device to the A D domain. Syntax join Parameters None Example admin(system.radius.ldap)> join...
Page 367: System Radius Policy Commands
4-57 System CLI Commands Reference 4.13 System RADIUS Policy Commands policy System RADIUS Commands Displays the policy submenu. Syntax admin(system.radius)> policy admin(system.radius.policy)> The items available under this command are shown below. Command Description Ref. Sets the group’s access policy. page 4-58 show Shows the group’s access policy.
Page 368: Set
4-58 WS2000 Wireless Switch System Reference Guide 4.13.1 System RADIUS Policy set Command System RADIUS Policy Commands Sets a group’s access to WLANs. Syntax set <group> <idx> Parameters set <group> <idx> Gives the group <group> access to WLAN with a list of indexes <idx>. The list <idx> can either be a single index or several indexes separated by spaces.
Page 369: Show
4-59 System CLI Commands Reference 4.13.2 System RADIUS Policy show Command show System RADIUS Policy Commands Displays the access policy details for all groups. Syntax show Parameters None Example admin(system.radius.policy)>set g1 2 3 4 admin(system.radius.policy)>show List of Access Policies : 2 3 4 : No Wlans Related Commands Sets the group WLAN access settings.
Page 370 4-60 WS2000 Wireless Switch System Reference Guide 4.14 System RADIUS Proxy Commands proxy System RADIUS Commands Displays the proxy submenu. Syntax admin(system.radius)> proxy admin(system.radius.proxy)> The items available under this command are shown below. Command Description Ref. Adds a proxy realm. page 4-61 Deletes a proxy realm.
Page 371: System Radius Proxy Commands
4-61 System CLI Commands Reference 4.14.1 System RADIUS Proxy add Command System RADIUS Proxy Commands Adds a proxy realm. Syntax add <name> <ip> <port> <secret> Parameters add <realm> <ip> <port> Add a proxy realm with realm name <realm>, RADIUS server IP address <ip>, port <port>, and shared secret <secret>.
Page 372: Del
4-62 WS2000 Wireless Switch System Reference Guide 4.14.2 System RADIUS Proxy del Command System RADIUS Proxy Commands Deletes a proxy realm. Syntax del <realm> Parameters del <realm> Deletes a proxy server realm with name <realm>. Example admin(system.radius.proxy)>add realm1 192.168.102.42 225 realmpass admin(system.radius.proxy)>show realm Proxy Realms -------------------------------------------------------------------------...
Page 373: Clearall
4-63 System CLI Commands Reference 4.14.3 System RADIUS Proxy clearall Command clearall System RADIUS Proxy Commands Clears all the proxy server records. Syntax clearall Parameters None Example admin(system.radius.proxy)> clearall...
Page 374: Set
4-64 WS2000 Wireless Switch System Reference Guide 4.14.4 System RADIUS Proxy set Command System RADIUS Proxy Commands Sets the proxy server parameters. Syntax set delay <delay> set count <count> Syntax: delay <delay> Sets the retry delay of the proxy server to <delay> minute (5–10). count <count>...
Page 375: Show
4-65 System CLI Commands Reference 4.14.5 System RADIUS Proxy show Command show System RADIUS Proxy Commands Shows the proxy server parameters. Syntax show [proxy|realm] Parameters show [proxy|realm] Displays proxy server parameters. • proxy – Displays the proxy server parameters. • realm – Displays proxy server realm information. Example admin(system.radius.proxy)>add realm1 192.168.102.42 225 realmpass admin(system.radius.proxy)>show realm...
Page 376: System Redundancy Commands
4-66 WS2000 Wireless Switch System Reference Guide 4.15 System Redundancy Commands redundancy system Displays the redundancy submenu. Syntax admin(system)> redundancy admin(system.redundancy)> The items available under this command are shown below. Command Description Ref. Sets redundancy parameters. page 4-67 show Shows redundancy settings. page 4-69 quit Quits the CLI...
Page 377: Set
4-67 System CLI Commands Reference 4.15.1 System Redundancy set Command System Redundancy Commands Sets the parameters for redundant switch mode. Syntax set [op_state|mode|heartbeat|revertdelay|redundancy|preempt|virtualip] set mode <mode> set op_state <state> set heartbeat <interval> set revertdelay <delay> set redundancy <subnet> <state> set preempt <mode> set virtualip <subnet>...
Page 378: Related Commands
4-68 WS2000 Wireless Switch System Reference Guide Related Commands show Displays the redundancy settings.
Page 379: Show
4-69 System CLI Commands Reference 4.15.2 System Redundancy show Command show System Redundancy Commands Displays the switch redundancy settings. Syntax show all Parameters None Example admin(system.redundancy)>show all redundancy configured mode : primary redundancy operational mode : VRRP daemon not running redundancy operational state : standalone heart beat interval...
Page 380: System Snmp Commands
4-70 WS2000 Wireless Switch System Reference Guide 4.16 System SNMP Commands snmp system Displays the SNMP submenu. Syntax admin(system)> snmp admin(system.snmp)> The items available under this command are shown below. Command Description Ref. access Goes to the SNMP access submenu. page 4-71 traps Goes to the SNMP traps submenu.
Page 381 4-71 System CLI Commands Reference 4.17 System SNMP Access Commands access System SNMP Commands Displays the SNMP access menu. Syntax admin(system.snmp)> access admin(system.snmp.access)> The items available under this command are shown below. Command Description Ref. Adds SNMP access entries. page 4-72 delete Deletes SNMP access entries.
Page 382: System Snmp Access Commands
4-72 WS2000 Wireless Switch System Reference Guide 4.17.1 System SNMP Access add Command System SNMP Access Commands Adds SNMP access list entries. Syntax add [acl|v1v2c|v3] add acl <ip1> <ip2> add v1v2c <comm> <access> [<oid>|all] add v3 <user> <access> [<oid>|all] <sec> <auth> <pass1> <priv> <pass2> Parameters add acl <ip1>...
Page 383 4-73 System CLI Commands Reference index username : fred access permission : read/write object identifier : 1.3.6.6 security level : none auth algorithm : md5 auth password : ******** privacy algorithm : des privacy password : ******** admin(system.snmp.access)>add v3 judy rw 1.3.6.1 auth/priv md5 changeme des changemetoo admin(system.snmp.access)>list v3 2 index...
Page 384: Delete
4-74 WS2000 Wireless Switch System Reference Guide 4.17.2 System SNMP Access delete Command delete System SNMP Access Commands Deletes SNMP access entries. Syntax delete [acl|v1v2c|v3] [<idx>|all] Parameters delete Deletes SNMP access entries. [acl|v1v2c|v3] • acl – Deletes SNMP access list entries [<idx>|all] •...
Page 385 4-75 System CLI Commands Reference admin(system.snmp.access)>delete v3 2 admin(system.snmp.access)>list v3 all index username : fred access permission : read/write object identifier : 1.3.6.6 security level : none auth algorithm : md5 auth password : ******** privacy algorithm : des privacy password : ******** admin(system.snmp.access)>...
Page 386: List
4-76 WS2000 Wireless Switch System Reference Guide 4.17.3 System SNMP Access list Command list System SNMP Access Commands Lists SNMP access entries. Syntax list [acl|v1v2c] list v3 [<idx>|all] Parameters list [acl|v1v2c] • acl – Lists SNMP access control list entries. •...
Page 387: Show
4-77 System CLI Commands Reference 4.17.4 System SNMP Access show Command show System SNMP Access Commands Displays the SNMP v3 engine ID. Syntax show eid Parameters None Example admin(system.snmp.access)>show eid WS2000 snmp v3 engine id : 0000018457D71CDFF86FD8FC admin(system.snmp.access)>...
Page 388 4-78 WS2000 Wireless Switch System Reference Guide 4.18 System SNMP Traps Commands traps System SNMP Commands Displays the SNMP traps submenu. Syntax admin(system.snmp)> traps admin(system.snmp.traps)> The items available under this command are shown below. Command Description Ref. Adds SNMP trap entries. page 4-79 delete Deletes SNMP trap entries.
Page 389: System Snmp Traps Commands
4-79 System CLI Commands Reference 4.18.1 System SNMP Traps add Command System SNMP Traps Commands Adds SNMP traps. Syntax add [v1v2c|v3] add v1v2c <ip> <port> <comm> <ver> add v3 <ip> <port> <user> <sec> <auth> <pass1> <priv> <pass2> Parameters v1v2c <ip> <port> Adds an SNMP v1/v2c trap entry.
Page 390 4-80 WS2000 Wireless Switch System Reference Guide admin(system.snmp.traps)>add v3 192.168.103.3 80 bomuser auth md5 bomuser1 admin(system.snmp.traps)>add v3 182.168.103.4 80 blistuser auth/priv md5 blistuser des listuser admin(system.snmp.traps)>list v3 all index destination ip : 192.168.103.3 destination port : 80 username : bomuser security level : auth auth algorithm...
Page 391: Delete
4-81 System CLI Commands Reference 4.18.2 System SNMP Traps delete Command delete System SNMP Traps Commands Deletes SNMP trap entries. Syntax delete [v1v2c|v3] [<idx>|all] Parameters delete Deletes SNMP access entries. [acl|v1v2c|v3] • acl – Deletes SNMP access list entries [<idx>|all] •...
Page 392: List
4-82 WS2000 Wireless Switch System Reference Guide 4.18.3 System SNMP Traps list Command list System SNMP Traps Commands Lists SNMP trap entries. Syntax list v1v2c list v3 [<idx>|all] Parameters list v1v2c Lists SNMP v1/v2c traps entries. list v3 [<idx>|all] Lists SNMP v3 traps definition with index <idx>. lists all SNMP v3 traps definitions.
Page 393: Set
4-83 System CLI Commands Reference 4.18.4 System SNMP Traps set Command System SNMP Traps Commands Sets SNMP trap parameters. Syntax set [cold|cfg|lowcf|port|dos-attack|snmp-auth|snmp-acl|mu-assoc| mu-unassoc|mu-deny-assoc|mu-deny-auth|ap-adopt|ap-unadopt| ap-denied-adopt|ap-radar|rogue-ap|hotspot-mu-state| user-login-failure|interface|admin-passwd-change|dyndns-update| wids-mu|wids-radio|wids-switch|ips] <mode> set cf-thresh <memory_kb> set min-pkt <pkt> set dos-rate-limit <seconds> set rate <rate> <scope> <value> Parameters set [cold|cfg|lowcf|port|dos-attack|snmp-auth|snmp-acl|mu-assoc|mu-unassoc| mu-deny-assoc|mu-deny-auth|ap-adopt|ap-unadopt|ap-denied-adopt|ap-radar|...
Page 394 4-84 WS2000 Wireless Switch System Reference Guide • admin-passwd-change – Admin password change trap • dyndns-update – Dynamic DNS update trap • wids-mu – WIDS MU event trap • wids-radio – WIDS radio event trap • wids-switch – WIDS switch event trap •...
Page 395 4-85 System CLI Commands Reference NOTE: <value> can be a number with up to two decimal places, except for assoc_mus, which must be an integer. Example admin(system.snmp.traps)>show trap SNMP System Traps snmp cold start : disable snmp config changed : disable low compact flash memory : disable SNMP Network Traps...
Page 396 4-86 WS2000 Wireless Switch System Reference Guide SNMP Network Traps physical port status change : enable denial of service : enable SNMP Traps snmp auth failure : disable snmp acl violation : disable SNMP MU Traps mu associated : disable mu unassociated : enable mu denied association...
Page 397: Show
4-87 System CLI Commands Reference 4.18.5 System SNMP Traps show Command show System SNMP Traps Commands Shows SNMP trap parameters. Syntax show [trap|rate-trap] Parameters show [trap|rate-trap] Displays trap settings. • trap – Displays SNMP trap parameter settings. • rate-trap – Shows SNMP rate-trap parameter settings. Example admin(system.snmp.traps)>show trap SNMP System Traps...
Page 398 4-88 WS2000 Wireless Switch System Reference Guide admin(system.snmp.traps)>show rate-trap SNMP Switch Rate Traps pkts/s greater than : disable throughput(Mbps) greater than : disable num of associated mu greater than : disable SNMP Wlan Rate Traps pkts/s greater than : disable throughput(Mbps) greater than : disable avg bit speed(Mbps) less than...
Page 399: System Ssh Commands
4-89 System CLI Commands Reference 4.19 System SSH Commands system Displays the secure shell (SSH) submenu. Syntax admin(system)> ssh admin(system.ssh)> The items available under this command are shown below. Command Description Ref. Sets SSH parameters page 4-90 show Shows SSH parameters. page 4-91 save Saves the configuration to system flash...
Page 400: Set
4-90 WS2000 Wireless Switch System Reference Guide 4.19.1 System SSH set Command System SSH Commands Sets secure shell parameters for system access. Syntax set auth-timeout <authentication timeout> set inactive-timeout <inactive timeout> Parameters auth-timeout Sets the maximum time <authentication timeout> (0–65535 seconds) allowed for <authentication SSH authentication to occur before executing a timeout.
Page 401: Show
4-91 System CLI Commands Reference 4.19.2 System SSH show Command show System SSH Commands Shows secure shell timeout parameters. Syntax show all Parameters None Example admin(system.ssh)>set auth-timeout 60 admin(system.ssh)>set inactiv 2000 admin(system.ssh)>show all Authentication Timeout : 60 SSH Client Inactivity Timeout : 2000 admin(system.ssh)>...
Page 402: System User Database Commands
4-92 WS2000 Wireless Switch System Reference Guide 4.20 System User Database Commands userdb system Displays the userdb submenu. Syntax admin(system)> userdb admin(system.userdb)> The items available under this command are shown below. Command Description Ref. user Goes to the user submenu. page 4-103 group Goes to the group submenu.
Page 403 4-93 System CLI Commands Reference 4.21 System User Database Group Commands group System User Database Commands Displays the group submenu. Syntax admin(system.userdb)> group admin(system.userdb.group)> The items available under this command are shown below. Command Description Ref. create Creates a new group. page 4-95 delete Deletes a group.
Page 404: System User Database Group Commands
4-94 WS2000 Wireless Switch System Reference Guide 4.21.1 System Userdb Group add Command System User Database Group Commands Adds a user to a group. Syntax add <userid> <group> Parameters add <userID> Adds the user specified by <userID> to the group <groupID>. <userID> must <groupID>...
Page 405: Create
4-95 System CLI Commands Reference 4.21.2 System Userdb Group create Command create System User Database Group Commands Creates a new group. Syntax create <group> <vlan-id> Parameters create <group> <vlan-id> Creates a new group with the ID <group>. <group> can be an alphanumeric string.
Page 406: Delete
4-96 WS2000 Wireless Switch System Reference Guide 4.21.3 System Userdb Group delete Command delete System User Database Group Commands Deletes a group from the database. Syntax delete <group> Parameters delete <groupID> Deletes the group <group> from the database. A warning occurs if there are still users assigned to that group.
Page 407 4-97 System CLI Commands Reference VanId Start Time : 0000 Expiry Time : 2359 Access on Days : All Related Commands Adds users to a group. show user Displays a list of users in a group.
Page 408: Clearall
4-98 WS2000 Wireless Switch System Reference Guide 4.21.4 System Userdb Group clearall Command clearall System User Database Group Commands Clears all the groups in the Groups list. Before clearing all the groups, ensure that no user account is associated to the groups. Syntax clearall Parameters...
Page 409: Remove
4-99 System CLI Commands Reference 4.21.5 System Userdb Group remove Command remove System User Database Group Commands Removes a user from a group. Syntax remove <userid> <group> Parameters remove <userid> Removes the user <userid> from the group <group>. <group> Example admin(system.userdb.group)>show users g1 List of Users of Group John...
Page 410: Set
4-100 WS2000 Wireless Switch System Reference Guide 4.21.6 System Userdb Group set Command System User Database Group Commands Sets the different group parameters. Syntax set [vlan|day-access|guest-group|start-time|end-time] set [start-time|end-time} <time> set vlan <group> <vlan> set day-access <group> [all|weekdays|<days>] set guest-group <group> Parameters vlan <group>...
Page 411 4-101 System CLI Commands Reference admin(system.userdb.group)> set guest-group Group1 admin(system.userdb.group)>set guest-group guests admin(system.userdb.group)>show groups List of Group Names Groupname : g1 Guest Group : NO VanId : 10 Start Time : 0000 Expiry Time : 2359 Access on Days : All Groupname : g2 Guest Group...
Page 412: Show
4-102 WS2000 Wireless Switch System Reference Guide 4.21.7 System Userdb Groups show Command show System User Database Group Commands Shows the existing groups. Syntax show [groups|users <group>] Parameters show [groups| Displays user database groups information. users <group>] • group – Displays a list of the defined groups. •...
Page 413 4-103 System CLI Commands Reference 4.22 System User Database User Commands user System User Database Commands Displays the user submenu. Syntax admin(system.userdb)> user admin(system.userdb.user)> The items available under this command are shown below. Command Description Ref. Adds a new user to the database. page 4-104 Deletes a user from the database.
Page 414: System User Database User Commands
4-104 WS2000 Wireless Switch System Reference Guide 4.22.1 System Userdb User add Command System User Database User Commands Adds a new user to the database. Syntax add <userid> <password> Parameters add <userid> <password> Adds a user to the database with the ID <userid> and password <password>...
Page 415: Del
4-105 System CLI Commands Reference 4.22.2 System Userdb User del Command System User Database User Commands Deletes a user from the database. Syntax del <userid> Parameters del <userid> Deletes the user with the ID <userid> from the database. Example admin(system.userdb.user)>show users List of User Ids Guest User John...
Page 416: Clearall
4-106 WS2000 Wireless Switch System Reference Guide 4.22.3 System Userdb User clearall Command clearall System User Database User Commands Clears all the users from the local database. Syntax clearall Parameters None Example admin(system.userdb.user)>show users List of User Ids Guest User John Jane Bill...
Page 417: Set
4-107 System CLI Commands Reference 4.22.4 System Userdb User set Command System User Database User Commands Sets the password for a user. Syntax set <userid> <password> Parameters set <userID> Resets the password for user with <userid> to <password>. <password> Example admin(system.userdb.user)>set fred frednew Related Commands Adds a new user.
Page 418: Show
4-108 WS2000 Wireless Switch System Reference Guide 4.22.5 System Userdb Users show Command show System User Database User Commands Shows a list of users and group membership for a particular user. Syntax show [groups <userid>|users] Parameters show Displays group membership and user information. [groups <userid>|users] •...
Page 419: System User Database User Guest Commands
4-109 System CLI Commands Reference 4.23 System User Database User Guest commands guest System User Database User Commands Displays the Guest submenu. Syntax admin(system.userdb.user)> guest admin(system.userdb.guest)> The items available under this command are shown below. Command Description Ref. Sets the parameters for guest users. page 4-110 show Shows the list of guest users...
Page 420: Set
4-110 WS2000 Wireless Switch System Reference Guide 4.23.1 System Userdb User Guest set Command System User Database User Commands Sets the parameters for guest users. Syntax set [guest-user|start-date|expiry-date] set guest-user <guest-user> <guest-group> set start-date <guest-user> <date-time> set expiry-date <guest-user> <date-time> Parameters guest-user Adds the guest user <guest-user>...
Page 421: Show
4-111 System CLI Commands Reference 4.23.2 System Userdb User Guest show Command show System User Database User Commands Displays information for guest users and guest user groups. Syntax show [groups|users] Parameters show [guests|users] Displays guest information. • groups – Displays the list of guest user groups •...
Page 422: Clear
4-112 WS2000 Wireless Switch System Reference Guide 4.23.3 System Usredb User Guest clear Command clear System User Database User Commands Clears all guest user and guest user groups from the local database. Syntax clear [guest-group|guest-user] clear guest-group <guest-group> clear guest-user <guest-user> Parameters guest-group Clears the guest group indicated by <guest-group>...
Page 423 4-113 System CLI Commands Reference 4.24 System WS2000 Commands WS2000 system Displays the WS 2000 submenu. Syntax admin(system)> ws2000 admin(system.ws2000)> The items available under this command are shown below. Command Description Ref. Adds an administrative user page 4-114 delete Removes an administrative user page 4-115 restart Restarts the WS 2000 Wireless Switch...
Page 424: System Ws2000 Commands
4-114 WS2000 Wireless Switch System Reference Guide 4.24.1 System WS2000 add Command System WS2000 Commands Adds a device that is allowed administrative access to the switch over WLAN. Syntax add administrator <ip> Parameters add administrator Adds the device specified by <ip> as an administrator for this device. <ip>...
Page 425: Delete
4-115 System CLI Commands Reference 4.24.2 System WS2000 delete Command delete System WS2000 Commands Removes a device that is allowed administrative access to the switch over WLAN. Syntax delete administrator [<ip>|all] Parameters delete administrator Removes the specified device that is allowed administrative access of the [<ip>|all] switch from WLAN .
Page 426: Restart
Parameters None Example admin(system.ws2000)>restart Restarting system. WS 2000 Wireless Switch 2.4.0.0-011B Copyright(c) Motorola Inc. 2003-2008. All rights reserved. Press escape key to run boot firmware ..Power On Self Test testing ram : pass testing nor flash : pass...
Page 427: Set
4-117 System CLI Commands Reference 4.24.4 System WS2000 set Command System WS2000 Commands Sets WS 2000 system parameters. Syntax set [airbeam|ftp|ssh|applet|cc|cli|email|loc|name|domain-name|snmp| timeout|limited-access|dns-ip|sslv2|support-sshv1|dns-relay-mode] set airbeam [mode|passwd|logging] set airbeam mode <mode> set airbeam passwd <password> set airbeam logging <mode> set [ftp|ssh|snmp] [lan|wan] [mode <mode>|logging <mode>] set [applet|cli] [lan|wan|slan|swan] [mode <mode>|logging <mode>] set email <email>...
Page 428 4-118 WS2000 Wireless Switch System Reference Guide cli [lan|wan|slan|swan] Configures access to the Command Line Interface (CLI). [mode <mode>| • lan mode <mode> – Enables/disables http applet access from LAN. logging <mode>] • wlan mode <mode> – Enables/disables http applet access from WAN. •...
Page 429 0 limit ws2000 access : disable System Wide DNS IP Address : 192.168.0.1 admin(system.ws2000)>set name BldgC admin(system.ws2000)>set email johndoe@motorola.com admin(system.ws2000)>set applet lan enable admin(system.ws2000)>set airbeam mode enable admin(system.ws2000)>set airbeam passwd changeme admin(system.ws2000)>show all system name...
Page 430 4-120 WS2000 Wireless Switch System Reference Guide http/s timeout interval in minutes: 0 limit ws2000 access : disable System Wide DNS IP Address : 192.168.0.1 admin(system.ws2000)>...
Page 431: Show
Example admin(system.ws2000)>show all system name : Atlanta1 system location : Atlanta Field Office system Domain Name : docteam.motorola.com admin email address : LeoExample@motorola.com system uptime : 0 days 4 hours 33 minutes WS2000 firmware version : 2.3.1.0-004X WS2000 firmware build time...
Page 432: System Cf Commands
4-122 WS2000 Wireless Switch System Reference Guide 4.25 System CF commands system Displays the CF submenu. Syntax admin(system)> cf admin(system.cf)> The items available under this command are shown below. Command Description Ref. Lists the content of the CF card page 4-123 quit Quits the CLI page 4-1...
Page 433 4-123 System CLI Commands Reference 4.25.1 System CF ls Command System CF commands Displays the CF card’s contents. Syntax ls {<directory-name>} Parameters ls <directory-name> Lists the contents of the CF card. The <directory-name> parameter is optional. Example admin(system.cf)> ls mf12.bin mf_02020200003R.bin admin(system.cf)>...
Page 434: System Http Commands
4-124 WS2000 Wireless Switch System Reference Guide 4.26 System HTTP commands http system Displays the http submenu. Syntax admin(system)> http admin(system.http)> The items available under this command are shown below. Command Description Ref. import Imports the Secured HTTP self certificate page 4-125 show Shows all the Secured HTTP certificates.
Page 435: Import
4-125 System CLI Commands Reference 4.26.1 System HTTP import Command import System HTTP commands Imports Secured HTTP self certificates. Syntax import self <cert-id> Parameters import self <cert-id> Imports the Secured HTTP Self Certificate identified by the ID <cert-id>. Example admin(system.http)> import self 1...
Page 436: Show
4-126 WS2000 Wireless Switch System Reference Guide 4.26.2 System HTTP show Command show System HTTP commands Displays all Secure HTTP certificates on this device. Syntax show all Parameters None Example admin(system.http)> show all http self certificate : default admin(system.http)>...
Page 437: System Test Commands
4-127 System CLI Commands Reference 4.27 System Test Commands test system Displays the test submenu. Syntax admin(system)> test admin(system.test)> The items available under this command are shown below. Command Description Ref. Sets the different test parameters page 4-128 show Displays the different test parameters and their set values. page 4-129 quit Quits the CLI...
Page 438: Set
4-128 WS2000 Wireless Switch System Reference Guide 4.27.1 System Test set Command System Test Commands Configures the different test parameters. Syntax set flow padding parp sip-portcheck weighted-wme int1 hosts mu_limit int4 str1 str2 str3 str4 interval...
Page 439: Show
4-129 System CLI Commands Reference 4.27.2 System Test show Command show System Test Commands Displays the test parameters. Syntax show all Parameters None Example admin(system.test)> show all admin(system.test)>show all half fc window for ap100 val [ 0x0000 ....0 ] broadcasts in psp val [ 0x0000 ..
Page 440 4-130 WS2000 Wireless Switch System Reference Guide...
Page 441: Chapter 5: Statistics Commands
Statistics Commands Statistics commands are used to view the different statistical information of the WS2000 Wireless Switch. 5.1 stats Admin Menu Commands Use the command to go to the Stats menu stats admin>stats admin(stats)> The following commands are available under the Stats menu: Command Description Ref.
Page 442: Stats Show Command
5-2 WS2000 Wireless Switch System Reference Guide 5.2 Stats Show Command show stats Displays the system status and statistics for either the specified subnet or the WAN. Syntax show [leases|subnet|wan|stp|ips] show leases show subnet <idx> show wan show stp <idx> show ips [global-stats|category-stats] show ips global-stats show ips category-stats <category-name>...
Page 443 Statistics Commands tx overruns : 0 tx carrier errors : 0 Port 1 link status : up speed : 100 Mbps Port 2 link status : up speed : 100 Mbps Port 3 link status : down Port 4 link status : down Port 5 link status : down Port 6...
Page 444 5-4 WS2000 Wireless Switch System Reference Guide show ips global-stats example. admin(stats)>show ips global-stats IPS GLOBAL STATISTICS ================================================ Number of Packets Received : 124832934 Number of Packets Processsed : 124832899 Number of Packets Dropped : 35 Number of Connecti ns Disconnected: 6 show ips category-stats example.
Page 445: Statistics Rf Commands
Statistics Commands 5.3 Statistics RF Commands stats Displays the RF statistics submenu. Syntax admin(stats)> rf admin(stats.rf)> The items available under this command are shown below. Command Description Ref. show Shows RF statistics. page 5-7 reset Resets/clears all RF statistics. page 5-6 quit Quits the CLI.
Page 446: Reset
5-6 WS2000 Wireless Switch System Reference Guide 5.3.1 Stats RF reset Command reset Statistics RF Commands Resets/clears all RF statistics. Syntax reset Parameters None Example admin(stats.rf)>reset admin(stats.rf)>...
Page 447 Statistics Commands 5.3.2 Stats RF show Command show Statistics RF Commands Shows radio frequency (RF) statistics. Syntax show [all|wlan|ap|mu|mesh-base|mesh-client|total] show all [wlan|ap|mu|mesh-base|mesh-client] show wlan <idx> show ap <idx> show mu <mu> show mesh-base <base> show mesh-client <client> show total Syntax: show all [wlan|ap|mu| Shows all statistics for: mesh-base|mesh-client]...
Page 448 5-8 WS2000 Wireless Switch System Reference Guide Name : WLAN4 Status : Disabled Index Name : WLAN5 Status : Disabled Index Name : WLAN6 Status : Disabled Index Name : WLAN7 Status : Disabled Index Name : WLAN8 Status : Disabled admin(stats.rf)>show wlan 1 Name : WLAN1...
Page 449 Statistics Commands ap index ap status : not connected ap index ap status : not connected ap index ap status : not connected ap index : 10 ap status : not connected ap index : 11 ap status : not connected ap index : 12 ap status...
Page 450 5-10 WS2000 Wireless Switch System Reference Guide...
Page 452 MOTOROLA INC. 1303 E. ALGONQUIN ROAD SCHAUMBURG, IL 60196 http://www.motorola.com 72E-132762-01 Revision A December 2009...

Motorola WS2000 - Wireless Switch - Network Management Device Cli Reference Manual

Table of Contents

Chapter 1: Product Overview

Chapter 2: Admin and Common Commands

Chapter 3: Network CLI Commands Reference

3.3 Network Ap Default Commands Default

3.9 Network Ap Mesh Commands Mesh

3.27 Network WAN Nat Commands Nat

Chapter 4: System CLI Commands Reference

Chapter 5: Statistics Commands

Quick Links

Chapters

Related Manuals for Motorola WS2000 - Wireless Switch - Network Management Device

Summary of Contents for Motorola WS2000 - Wireless Switch - Network Management Device