Installing Cisco San-Os Software From The Cli - Cisco 9134 - MDS Multilayer Fabric Switch Troubleshooting Manual

Chapter 2 Troubleshooting Installs, Upgrades, and Reboots
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
Note

Installing Cisco SAN-OS Software from the CLI

To perform an automated software upgrade on any switch from the CLI, follow these steps:
Step 1 Log into the switch through the console, Telnet, or SSH port of the active supervisor.
Step 2 Create a backup of your existing configuration file, if required.
Step 3 Perform the upgrade by issuing the install all command.
The example below demonstrates upgrading from SAN-OS 2.0(2b) to 2.1(1a) using the install all
command with the source images located on a SCP server.
Tip
ca-9506# install all system scp://testuser@dino/tftpboot/rel/qa/2_1_1a/final/m95
00-sf1ek9-mz.2.1.1a.bin kickstart scp://testuser@dino/tftpboot/rel/qa/2_1_1a/fin
al/m9500-sf1ek9-kickstart-mz.2.1.1a.bin
For scp://testuser@dino, please enter password:
For scp://testuser@dino, please enter password:
Copying image from scp://testuser@dino/tftpboot/rel/qa/2_1_1a/final/m9500-sf1ek9
-kickstart-mz.2.1.1a.bin to bootflash:///m9500-sf1ek9-kickstart-mz.2.1.1a.bin.
[####################] 100% -- SUCCESS
Copying image from scp://testuser@dino/tftpboot/rel/qa/2_1_1a/final/m9500-sf1ek9
-mz.2.1.1a.bin to bootflash:///m9500-sf1ek9-mz.2.1.1a.bin.
[####################] 100% -- SUCCESS
Verifying image bootflash:///m9500-sf1ek9-kickstart-mz.2.1.1a.bin
[####################] 100% -- SUCCESS
Verifying image bootflash:///m9500-sf1ek9-mz.2.1.1a.bin
[####################] 100% -- SUCCESS
Extracting "slc" version from image bootflash:///m9500-sf1ek9-mz.2.1.1a.bin.
[####################] 100% -- SUCCESS
Extracting "ips" version from image bootflash:///m9500-sf1ek9-mz.2.1.1a.bin.
[####################] 100% -- SUCCESS
Extracting "svclc" version from image bootflash:///m9500-sf1ek9-mz.2.1.1a.bin.
[####################] 100% -- SUCCESS
Extracting "system" version from image bootflash:///m9500-sf1ek9-mz.2.1.1a.bin.
OL-9285-05
Before exiting the session, be sure that the upgrade process is complete. The wizard displays
status messages as the upgrade proceeds. Check the lower left-hand corner of the wizard for the
status messages. First, the wizard displays the message
by . Then the wizard displays a second message
InProgress Polling
the final
Upgrade Finished
Always carefully read the output of install all compatibility check. This compatibility check
tells you exactly what needs to be upgraded (BIOS, loader, firmware) and what modules are not
hitless. If there are any questions or concerns about the results of the output, select n to stop the
installation and contact the next level of support.
Troubleshooting Cisco SAN-OS Software Upgrades and Downgrades
.
Cisco MDS 9000 Family Troubleshooting Guide, Release 3.x
followed a few seconds later
Success
before displaying
Success
2-11