Extron electronics DMP 128 Plus User Manual page 59

Command
Audio Group Master Commands
NOTES:
•
For information on configuring groups, see the DSP Configurator Help File.
•
A group must have assigned members for these commands to have an effect.
• X6@
For , a positive (+) value is assumed unless a negative (-) value is specified.
• X6@
If entering an
parameter).
• X6@ X6# X6$
, , and
Set a group fader value
Example:
Increment a group fader
value
Example:
Decrement a group
fader value
View the group fader
value
Mute a group
Unmute a group
View a group mute
value
Set soft limits
Example:
View soft limits
X6@
KEY: = Mute status:
X6#
= Group master group number:
X6$
= Group fader setting:
X6%
= Group fader increment/decrement:
X6^
= Group fader soft limit:
ASCII command
(host to device)
value outside the valid range for the group or outside the soft limits, the DMP 128 responds with an
values can be sent without leading zeroes.
E X6# X6$ }
D * GRPM
}
E D2*-239GRPM
X6# X6% }
E D * +GRPM
}
E D2*30+GRPM
X6# X6% }
E D * -GRPM
X6# }
E D GRPM
X6# }
E D *1GRPM
X6# }
E D *0GRPM
X6# }
E D GRPM
E X6# X6^
L * *
upper
X6^ }
GRPM
lower
E }
L2*60*-60GRPM
E X6# }
L GRPM
0
= Unmute
1
through
dB value in 0.1 dB steps, using negative numbers and eliminating decimal places using a
10x multiplier. -100.0dB to +80.0 dB is represented by
depends on the type of gain or trim block assigned to the group number (
dB value in 0.1 dB steps to raise or lower a group fader.
Gain uses 10x multiplier (+10 dB =
dB value in 0.1 dB steps. Gain uses 10x multiplier (+10 dB =
Response
(device to host)
X6# X6$]
GrpmD *
]
GrpmD2*-293
X6# X6$]
GrpmD *
]
GrpmD2*-263
X6# X6$]
GrpmD *
X6# X6$]
GrpmD *
X6# ]
GrpmD *1
X6# ]
GrpmD *0
X6# X6@]
GrpmD *
X6# X6^ X6^]
GrpmL * *
]
GrpmL2*60*-60
X6# X6^ X6^]
GrpmL * *
1
= Mute
64
100
+). + or - goes after the number.
DMP 128 Plus • SIS Configuration and Control
Additional description
E13
error (invalid
Set a group fader to a
X6$
value of .
Set group 2 fader control
to -29.3 dB.
X6#
Increase the level of by
X6%
dB.
Raise the group 2 fader
3 dB from -29.3 dB (set in
example above) to -26.3
dB.
Decrease the level of the
X6# X6%
group fader by
dB.
In verbose modes 0 and 1,
the response is simplified
X6$]
to .
Mute all blocks in group
X6#
.
Unmute all blocks in group
X6#
.
X6@
For group masters, is
always expressed as an
unsigned or negative value.
Set the groups soft limits to
X6^ X6^
and .
upper lower
Set the upper soft limit for
the group 2 fader to +6.0
dB and the lower limit to
-6.0 dB.
In verbose modes 0 and 1,
the response is simplified
X6^ X6^]
to * .
-1000 800
to . The valid range
X6#
).
100
+).
52