Advertisement
Quick Links
DTP3 T/R 301 • Setup Guide
This guide provides quick start instructions for an experienced installer to set up
and operate the DTP3 T 301 transmitter and DTP3 R 301 receiver. These DTP3
digital video Extenders can extend the following up to 330 feet (100 meters), using shielded twisted pair cabling:
•
HDMI digital video signal to 4K @ 60 Hz (4:4:4) (can include embedded digital audio)
•
Optional analog audio
•
Bidirectional RS‑232 control
NOTE:
Maximum transmission distances vary with resolutions used, cable types, and environment (see the
DTP3 T/R 301 User Guide at
USB
Computer
4K/60
USB
HDMI
POWER
A
12V
2.8 MAX
AUDIO
HOST
HDMI
Extron
DTP3 T 301
Transmitter
Figure 1.
Typical DTP3 T/R 301 Transmitter and Receiver Application
Installation
Turn off and disconnect all equipment power sources and mount the transmitter and receiver Extender units as required. The
units can be mounted in a variety of locations using optional Extron mounting accessories (see
the compatible mounting options).
Rear Panel Connections
POWER
12V
2.8 A MAX
AUDIO
DTP3 T 301
G G G
B B B
POWER
12V
1.0 A MAX
DTP3 R 301
N N N
Figure 2.
DTP3 T/R 301 Rear Panel Connectors and Features
www.extron.com
for full specifications).
Table
Microphone
SIG
LINK
OVER DTP3
B
RS-232
R
DTP3 OUT
Tx Rx G
HDMI
CAT6A Cable
up to 330' (100 m)
HOST
HDMI
C C C
A A A
SIG
LINK
SEND
PWR
OFF
DTP3 IN
I I I
•
USB HID & 2.0
•
Remote power (receiver to transmitter)
4K/60
USB
HDMI
Extron
POWER
12V
1.0 A MAX
DTP3 R 301
Receiver
SIG
LINK
OVER DTP3
A
RS-232
Tx Rx G
DTP3 OUT
F F F
D D D
OVER DTP3
1
RS-232
2
Tx Rx G
HDMI
M M M
J J J
75" Touch Display
Extron
SB 33 A 75-80
Sound Bar
Audio
SIG
LINK
OVER DTP3
SEND
1
3
L
R
PWR
RS-232
R
2
4
OFF
DTP3 IN
Tx Rx G
HDMI
DEVICES
AUDIO
USB
POWER
STANDBY
Camera
www.extron.com
to determine
B
HDMI
E E E
H H H
3
L
R
4
DEVICES
AUDIO
L L L
K K K
O O O
R
R
1
Advertisement
Related Manuals for Extron electronics DTP3 T/R 301
Summary of Contents for Extron electronics DTP3 T/R 301
- Page 1 STANDBY Camera Figure 1. Typical DTP3 T/R 301 Transmitter and Receiver Application Installation Turn off and disconnect all equipment power sources and mount the transmitter and receiver Extender units as required. The units can be mounted in a variety of locations using optional Extron mounting accessories (see www.extron.com...
- Page 2 Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises en garde dans la section « Power Supply » du DTP3 T/R 301 User Guide. RESET button and LED — This button initiates two levels of reset (see the DTP3 T/R 301 User Guide, at www.extron.com). Receiver Features...
- Page 3 Power Supply » du DTP3 T/R 301 User Guide. Reset button — This button initiates two levels of reset (see the DTP3 T/R 301 User Guide, at www.extron.com). LockIt™ Lacing Brackets Use an included LockIt lacing bracket to securely fasten an HDMI cable to each device as follows: Plug the HDMI cable into the panel connection.
- Page 4 F F F Figure 3. DTP3 T/R 301 Front Panel Features Power LED — The Extender is receiving power, either locally or remotely (via power‑over‑DTP — transmitter only). Configuration port — Connect to this USB mini‑C port (USB 2.0) for product configuration and firmware updates.