Ricoh J-P3 Service Manual page 109

20 February 2004
1913 [Temp. Cor. 1] Fusing Temperature Correction (Correction Timing)
Specifies the number of sheets to determine whether or not to apply the fusing
temperature correction. During a multi print job, the fusing temperature tends to
slightly overshoot around the 10th sheet and then stabilize. Temperature
overshooting may cause the glossiness to increase. To minimize the overshooting,
both fusing and pressure roller temperatures are decreased by the amount specified
in SP1-914 at the number of sheets specified in this SP mode, until the end of the
job. The temperatures are decreased in two steps.
Example: 162 mm/s line speed
First step (also called 'Mode 1'): After 5 sheets (SP 1-913-2), temperature drops by
5°C (SP 1-914-2).
Second step (also called 'Mode 2'): After 20 sheets (SP 1-913-7), temperature drops
by 10°C (SP 1-914-7).
Narrow: LT/A4 SEF width or less
Wide: Wider than LT/A4 SEF
1912 001 Mode 1: H
1912 002 Mode 1: M
1912 003 Mode 1: L
1912 004 Mode 1 OHP narrow
1912 005 Mode 1: H: wide
1912 006 Mode 2: H
1912 007 Mode 2: M
1912 008 Mode 2: L
1912 009 Mode 2: H: narrow
1912 010 Mode 2: H: wide
1914 [Temp. Cor. 2] Fusing Temperature Correction (Temperature Setting)
Specifies the temperature to be subtracted from the target temperatures specified in
SP1-105-4 to-24.
Narrow: LT/A4 SEF width or less
Wide: Wider than LT/A4 SEF
1914 001 Temp 1:H
1914 002 Temp 1:M
1914 003 Temp 1:L
1914 004 Temp 1 OHP narrow
1914 005 Temp 1 OHP wide
1914 006 Temp 2:H
1914 007 Temp 2:M
1914 008 Temp 2:L
1914 009 Temp 2 OHP narrow
1914 010 Temp 2 OHP wide
1915 [Stand-by Time]
1915 001 Job Receiving
Specifies the time to shift the machine into the stand-by mode when not receiving a
print start command after receiving a print preparation command.
1915 002 Job End
Specifies the time to shift the machine into the stand-by mode after the last job is
completed.
*BCU [1 to 255 / 5 / 1 sheet/step]
*BCU
*BCU
*BCU
*BCU [1 to 255 / 10 / 1 sheet/step]
*BCU [1 to 255 / 20 / 1 sheet/step]
*BCU [1 to 255 / 20 / 1 sheet/step]
*BCU [1 to 255 / 20 / 1 sheet/step]
*BCU [1 to 255 / 10 / 1 sheet/step]
*BCU [1 to 255 / 20 / 1 sheet/step]
*BCU [0 to 20 / 0 / 5°C /step]
*BCU [0 to 20 / 5 / 5°C /step]
*BCU [0 to 20 / 0 / 5°C /step]
*BCU [0 to 20 / 5 / 5°C /step]
*BCU [0 to 20 / 5 / 5°C /step]
*BCU [0 to 20 / 10 / 5°C /step]
*BCU [0 to 20 / 10 / 5°C /step]
*BCU [0 to 20 / 10 / 5°C /step]
*BCU [0 to 20 / 5 / 5°C /step]
*BCU [0 to 20 / 5 / 5°C /step]
*BCU [0 to 180 / 60 / 10 seconds/step]
0: The machine does not shift to the stand-by
mode.
*BCU [0 to 180 / 30 / 10 seconds/step]
0: The machine does not shift to the stand-by
mode.
5-13
ENGINE SERVICE MODE