IBM System x iDataPlex dx360 M2 Problem Determination And Service Manual page 7

2
Removing an I C multiplexer card . . . . . . . . . . . . . . . . 162
2
Installing an I C multiplexer card . . . . . . . . . . . . . . . . . 163
Removing a memory module . . . . . . . . . . . . . . . . . . 163
Installing a memory module . . . . . . . . . . . . . . . . . . . 164
Removing and installing a one-bay or four-bay hard disk drive bracket and
cable assembly . . . . . . . . . . . . . . . . . . . . . . 168
Removing a PCIe riser-card assembly from the system-board tray . . . . 171
Installing a PCIe riser-card assembly in the system-board tray . . . . . . 172
Removing a power supply from a 2U chassis . . . . . . . . . . . . 173
Installing a power supply in a 2U chassis . . . . . . . . . . . . . . 174
Removing a power supply from a 3U chassis . . . . . . . . . . . . 174
Installing a power supply in a 3U chassis . . . . . . . . . . . . . . 176
Removing a power-supply paddle card from an expansion enclosure
Installing a power-supply paddle card in an expansion enclosure . . . . . 179
Removing a storage enclosure
Installing a storage enclosure . . . . . . . . . . . . . . . . . . 181
Removing a storage-riser-card assembly, ServeRAID SAS controller, and
battery cable interposer card from a 3U chassis . . . . . . . . . . 181
Installing a storage-riser-card assembly, ServeRAID SAS controller, and
battery cable interposer card in a 3U chassis . . . . . . . . . . . 183
Removing and replacing FRUs
Removing a 2x2 2.5-inch SAS/SATA backplane . . . . . . . . . . . 185
Installing a 2x2 2.5-inch SAS/SATA backplane . . . . . . . . . . . . 185
Removing the 2U chassis from a Type 7825 iDataPlex rack . . . . . . . 186
Installing the 2U chassis in a Type 7825 iDataPlex rack . . . . . . . . 187
Removing the 3U chassis hard disk drive backplane
Installing the 3U chassis hard disk drive backplane . . . . . . . . . . 189
Removing a 3U chassis from a Type 7825 iDataPlex rack
Installing a 3U chassis in a Type 7825 iDataPlex rack . . . . . . . . . 191
Removing a front-panel assembly . . . . . . . . . . . . . . . . 192
Installing a front-panel assembly . . . . . . . . . . . . . . . . . 193
Removing an I/O enclosure configured with 2.5-inch hot-swap hard disk
drives . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Installing an I/O enclosure configured with 2.5-inch hot-swap hard disk
drives . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Removing an I/O enclosure configured with 3.5-inch simple-swap hard disk
drives . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Installing an I/O enclosure configured with 3.5-inch hot-swap hard disk
drives . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Removing a microprocessor and heat sink . . . . . . . . . . . . . 197
Installing a microprocessor and heat sink . . . . . . . . . . . . . . 199
Removing a PCIe riser-card assembly from the I/O enclosure . . . . . . 203
Installing a PCIe riser-card assembly in the I/O enclosure. . . . . . . . 203
Removing a power-supply paddle card from the system-board tray . . . . 204
Installing a power-supply paddle card in the system-board tray . . . . . . 205
Removing a power-supply paddle card from a 3U chassis
Installing a power-supply paddle card in a 3U chassis . . . . . . . . . 207
Removing the system-board tray . . . . . . . . . . . . . . . . . 208
Installing the system-board tray . . . . . . . . . . . . . . . . . 210
Chapter 6. Configuration information and instructions
Firmware updates . . . . . . . . . . . . . . . . . . . . . . . 213
Using the Setup utility . . . . . . . . . . . . . . . . . . . . . . 214
Starting the Setup utility . . . . . . . . . . . . . . . . . . . . 214
Setup utility menu choices . . . . . . . . . . . . . . . . . . . 214
Passwords . . . . . . . . . . . . . . . . . . . . . . . . . 217
. . . . . . . . . . . . . . . . . 180
. . . . . . . . . . . . . . . . . . 184
. . . 178
. . . . . . . . . 188
. . . . . . . 190
. . . . . . . 206
. . . . . . . . 213
Contents
v