B. Simulation List - Sharp AR-BC260 Service Manual

B. Simulation list

(1) Main/ Sub
Code
Function (Purpose)
Main Sub
1 1 Used to check the operations of the
scanner unit and its control circuit.
2 Used to check the sensors and
detectors in the scanner section and
the related circuits.
5 Used to check the scanner
(scanning) unit and its control circuit.
2 2 Used to check the operations of the
sensors and detectors in the
document feeder unit and their
related circuits.
3 Used to check the operations of the
motors, solenoids, and the PS clutch
in the document feeder unit.
3 2 Used to check the operations of the
sensors and detectors in the finisher
and the related circuits.
3 Used to check the loads in the
finisher and the control circuit.
10 Used to adjust the sections in the
finisher.
4 2 Used to check the operations of the
desk/large capacity tray sensors and
detectors and the related circuits.
3 Used to check the operations of the
desk/large capacity tray loads and
the control circuit.
5 Used to check the operations of the
clutch TRC and the monitor.
5 1 Used to check the operations of the
display lamp (LED)/LCD on the
operation panel and the control
circuits.
2 Used to check the operations of the
heater lamp and its control circuit.
3 Used to check the operations of the
scanner lamp and its control circuit.
4 Used to check the operations of the
discharge lamp and its control circuit.
6 1 Used to check the operations of the
loads (clutches and solenoids) in the
paper transport system, transfer, and
fusing, and the control circuit.
2 Used to check the operations of the
fan motors and the control circuits.
7 1 Used to set the aging conditions.
6 Used to set the cycle of intermittent
aging.
8 Used to set Yes/No of warm-up time
display.
9 Used to check the image quality and
operations of each color.
8 1 Used to check and adjust the
operations of the developing bias
voltage of each color and the control
circuit.
2 Used to check and adjust the
operation of each print mode main
charger grid voltage and the control
circuit.
6 Used to check and adjust the
operation of the transfer charger
current and the control circuit.
9 2 Used to check the operation of the
sensors and detectors in the inverter/
duplex section and the control circuit.
3 Used to check the operations of the
loads (motor, clutch, solenoid) in the
inverter/duplex section and the
control circuits.
Purpose
Operation test/check Scanner (reading)
Operation test/check Scanner (reading)
Operation test/check Scanner (reading)
Operation test/check Automatic document
feeder
Operation test/check Automatic document
feeder
Operation test/check Finisher
Operation test/check Finisher
Operation test/check Finisher
Operation test/check Paper feed
Operation test/check Paper feed
Operation test/check Paper feed
Operation test/check Operation (Display,
procedure)
Operation test/check Fusing
Operation test/check Scanner (reading)
Operation test/check Process
(Photoconductor,
developing, transfer,
cleaning)
Operation test/check Paper transport (paper
exit, switchback,
transport), transfer,
fusing
Operation test/check Others
Setting/Operation test/
check
Setting/Operation test/
check
Setting/Operation test/
check
Operation test/check Others
Adjustment/Operation Process
test/check (Photoconductor,
developing, transfer,
cleaning)
Adjustment/Operation Process
test/check (Photoconductor,
developing, transfer,
cleaning)
Adjustment/Operation Process
test/check (Photoconductor,
developing, transfer,
cleaning)
Operation test/check Inverter/Duplex
Operation test/check Inverter/Duplex
AR-BC260 SIMULATION 9 - 3
Section
Operation
Operation
Operation
Operation
Operation
Operation
Operation
Operation
Operation
Operation
Operation
Operation
Operation
Operation
Others Operation
Operation
Operation
Operation
Operation
Operation
Picture quality
Transfer
Operation
Operation
Item