Sharp AR-BC260 Service Manual page 152

2 -3
Purpose Operation test/check
Function Used to check the operations of the motors,
(Purpose) solenoids, and the PS clutch in the document feeder
unit.
Section Automatic document feeder
Item Operation
Operation/ 1. The names of the loads that can be operated are
Procedure displayed. Select the load to be checked with the
key, and the selected load is highlighted.
2. Press the [EXECUTE] key.
[When RSPF is installed]
MOT Motor
PSOL Paper feed solenoid
RSOL Paper reverse solenoid
GSOL Paper exit fate solenoid
CLH PS clutch
3
3 -2
Purpose Operation test/check
Function Used to check the operations of the sensors and
(Purpose) detectors in the finisher and the related circuits.
Section Finisher
Item Operation
Operation/ The operating status of the sensors and detectors of
Procedure the finisher is displayed. The active sensor/detector
display is highlighted.
(Sensors to be detected)
FES Inlet sensor
FPHPS Paddle HP sensor
FARHPS Bundle roller HP sensor
FFJHPS Alignment HP sensor (F)
FRJHPS Alignment HP sensor (R)
FAS Alignment tray sensor
FOBHPS Paper exit belt HP sensor
FBES Tray paper sensor
FSLS Paper surface sensor
FFPS Binding position sensor
FFHPS Binding HP sensor
FFRHPS Binding roller HP sensor
FFES Binding paper sensor
FFE Binding clock sensor
FULS Lift upper limit sensor
FLLS Lift lower limit sensor
FLE Lift clock sensor
FSHPS Slide HP sensor
FSTHPS Stapler HP sensor
FSS Staple sensor
FSUC Stapler connection sensor
FMLS Lift middle sensor
FSPS Self prime sensor
FFDS Front door sensor
FCS Upper cover sensor
FFDSW Front door switch
FJS
FSSS
FPTS
FPSS1
FPSS2
FPSS3
FPSS4
FPDS
FPUC
FPSHPS
FPE
[When the finisher is installed]
SBPED
SLDHP
SGBHP
SBUHP
SPPD
SJSW
SPSW2
SPSW3
SDIPSW1
SDIPSW2
SDIPSW3
SDIPSW4
SDIPSW5
SDIPSW6
3 -3
Purpose
Function
(Purpose)
Section
Item
Operation/
Procedure
During the load operation, the [EXECUTE] key and the load key
are highlighted. Under this state, pressing the [EXECUTE] key
interrupts the load operation.
(Loads to be selected)
FFM Transport motor
FPM Paddle motor
FAM Bundle exit motor
FFJM Alignment motor (F) FPSM
FRJM Alignment motor (R) FFC
FSM Slide motor
(When the finisher is installed)
SBSM Bin unit shift motor
SPFM Transport motor
SGBM Guide bar drive motor
AR-BC260 SIMULATION 9 - 14
Joint switch
Stapler safety switch
Punch timing sensor
Punch side resist sensor 1
Punch side resist sensor 2
Punch side resist sensor 3
Punch side resist sensor 4
Punch dust sensor
Punch connection
Punch side resist home position
Punch motor encoder
Sensor in bin
Lead cam HP sensor
Guide bar HP sensor
Bin unit HP sensor
Paper exit sensor
Joint switch
Push switch 2
Push switch 3
DIP switch (SW1)
DIP switch (SW2)
DIP switch (SW3)
DIP switch (SW4)
DIP switch (SW5)
DIP switch (SW6)
Operation test/check
Used to check the loads in the finisher and the
control circuit.
Finisher
Operation
1. The names of the loads that can be checked are
displayed. Select a load to be checked with the
key.
2. Press the [EXECUTE] key. The selected load
operates.
FFSM Stapler motor
FLM Shift motor
FPNM Punch motor
Puncher side resist motor
Folding clutch