Sharp AR-BC260 Service Manual page 163

Main Sub
code code
F2 73 Developing unit improper cartridge detection
(Yellow)
74 Developing unit CRUM trouble (Black)
75 Developing unit CRUM trouble (Cyan)
76 Developing unit CRUM trouble (Magenta)
77 Developing unit CRUM trouble (Yellow)
78 Registration trouble
80 Half-tone process control 1st batch error (Black)
81 Half-tone process control 1st batch error (Cyan)
82 Half-tone process control 1st batch error (Magenta)
83 Half-tone process control 1st batch error (Yellow)
84 Half-tone process control 2nd batch error (Black)
85 Half-tone process control2nd batch error (Cyan)
86 Half-tone process control 2nd batch error (Magenta)
87 Half-tone process control 2nd batch error (Yellow)
90 Half-tone process control limit error
F3 12 Cassette 1 lift-up trouble
F6 00 ICU-FAX communication trouble
01 FAX expansion flash memory error
04 FAX MODEM operation error
20 FAX write protect cancel
21 Combination error between the TEL/LIU PWB and
the FAX soft switch
97 The FAX-BOX PWB is not one for the AR-BC260.
(FAX detection)
98 Combination error between the FAX-BOX
destination information and the main unit destination
information.
F7 01 FAX board EEPROM read/write error
F9 00 ICU-PRT communication trouble (ICU detection)
01 PRT DRAM trouble
03 NIC port check error
20 HDD trouble (PRT controller detection)
H2 00 Thermistor open (HL1)
01 Thermistor open (HL2)
H3 00 Fusing section high temperature trouble (HL1)
01 Fusing section high temperature trouble (HL2)
H4 00 Fusing section low temperature trouble (HL1)
01 Fusing section low temperature trouble (HL2)
H5 01 5 continuous detections of POD1 not-reached jam
L1 00 Mirror feed trouble
L3 00 Mirror return trouble
L4 02 Paper feed motor lock trouble
06 Transfer belt lift motor trouble
07 Transfer belt motor trouble
11 Shift motor trouble
L8 01 No full wave signal
02 Full wave signal width abnormality
04 Main switch abnormality detection
PF 00 RIM copy inhibit signal reception
U0 00 ICU-OPE communication trouble (ICU/OPE
detection)
U1 01 FAX battery trouble
02 RTC read trouble
U2 00 EEPROM read/write error (SCN detection)
11 EEPROM check sum error (SCN detection)
22 SRAM memory check sum error
30 Manufacturing No. data discrepancy (ICU
80 EEPROM read/write error (SCN detection)
81 EEPROM check sum error (SCN detection)
90 EEPROM read/write error (PCU detection)
91 EEPROM check sum error (PCU detection)
U4 02 ADU alignment plate operation abnormality
Content
⇔
PCU)
AR-BC260 SIMULATION 9 - 25
Main Sub
code code
U6 00 Desk communication trouble
01 Desk tray 1 lift motor trouble
02 Desk tray 2 lift motor trouble
03 Desk tray 3 lift motor trouble
09 LCC lift motor trouble
10 Desk transport motor trouble
20 LCC communication trouble
21 LCC transport motor trouble
22 LCC 24V power abnormality
50 Desk incompatible trouble
51 LCC incompatible trouble
U7 00 RIC communication trouble
UC 02 CPT-ASIC trouble (MFP PWB trouble)
22 -5
Purpose Others
Function Used to check the ROM version of each unit
(Purpose) (section).
Item Software
Operation/ If there is any problem in the software, check the
Procedure ROM version of each section with this simulation
and replace with a new version if necessary.
(Sections to be displayed)
ICU ICU control
PCU Engine control section
SCANNER Scanner control section
COL REV DATA Color correction ROM
OPE PROG OPE control section
PRT BOOT PRT boot
PRT PROG PRT control section
FAX FAX control section
FIN-SORTER Finisher/Sorter
PUNCH Punch unit
DESK Desk
LCC Large capacity cassette
NIC NIC
PS PostScript
∗
The serial No. is entered in the title.
If the serial No. is invalid, "∗∗∗∗∗∗∗∗" is displayed.
Content