And Machine Operations - Sharp AR-BC260 Service Manual

3. Relationship of maintenance timing, consumable part life, display message, and
machine operations
A. Relationship of maintenance counter, display message, and machine operations
Counter name
Maintenance counter (Total)
Maintenance counter (Color)
Both of maintenance counter (Total) and
maintenance counter (Color)
Counter name
Maintenance counter (Total)
Maintenance counter (Color)
Both of maintenance counter (Total) and
maintenance counter (Color)
Message No.
1 (Now is maintenance timing. Code: Tx)
2 (Now is maintenance timing. Code: Cx)
3 (Now is maintenance timing. Code: Ax)
First digit of code: Kind of maintenance (T= Total, C= Color, A= Both)
Second digit of code: Maintenance cycle (A= 5K, B= 10K, C= 15K, D= 40K, E= 50K, F= 100K)
• Maintenance message is not displayed during a job (during operation/during job). (Message is displayed before/after a job.)
• When the maintenance counter (Total) exceeds the set value of SIM 21-1, the message is displayed. → The first digit of code is T.
• When the maintenance counter (Color) exceeds the set value of SIM 21-1, the message is displayed. → The first digit of code is C.
• When both of the maintenance counter (Total) and the maintenance counter (Color) exceed the set value of SIM 21-1, the message is
displayed.
→ The first digit of code is A.
• When SIM 26-38 is set to Print Allow, any job can be executed even during message display.
When SIM 24-4 (Maintenance counter (Total, Color) clear) is executed after completion of maintenance, the message is cleared.
B. Relationship of transfer unit system counter, display message, and machine operations
Counter name
Transfer unit print counter
Accumulated mileage of transfer unit
Number of use days of transfer unit
Counter name
Transfer unit print counter
Accumulated mileage of transfer unit
Number of use days of transfer unit
In addition to the above counters, the transfer waste-toner full sensor status is taken into consideration to make a message.
Sensor name
Transfer waste-toner full sensor
Sensor name
Transfer waste-toner full sensor
Specified value
SIM 21-1 setup value
Message when SIM 21-1 setup value x 110% is exceeded.
Specified value
SIM 21-1 setup value
x 110%
Message
Near end value
49,000 [sheet] or
99,000 [sheet]
20,890,333 [mm] or
34,951,002 [mm]
725 [day]
End value
50,000 [sheet] or
100,000 [sheet]
21,316,667 [mm] or
35,221,940 [mm]
740 [day]
Near end value
3 sec continuously ON
End value
1,000 [sheet] after
detection of near end
AR-BC260 MAINTENANCE LIST 10 - 10
Message when SIM 21-1 setup value is exceeded
When SIM 26-38 is
set to Print Allow.
Message 1
Message 2
Message 3
When SIM 26-38 is
set to Print Allow.
Message 1
Message 2
Message 3
Message when near end is over
When SIM 26-38 is
set to Print Allow.
Message 1
—
—
Message when end is over
When SIM 26-38 is
set to Print Allow.
Message 1
—
—
Message when near end is detected
When SIM 26-38 is
set to Print Allow.
—
Message when end is detected
When SIM 26-38 is
set to Print Allow.
Message 1
When SIM 26-38 is
set to Print Inhibit.
Message 1
Message 2
Message 3
When SIM 26-38 is
set to Print Inhibit.
Message 1
Message 2
Message 3
Print job YES/NO
YES
YES
YES
When SIM 26-38 is
set to Print Inhibit.
Message 1
—
—
When SIM 26-38 is
set to Print Inhibit.
Message 1
—
—
When SIM 26-38 is
set to Print Inhibit.
Message 1
When SIM 26-38 is
set to Print Inhibit.
Message 3