Push Buttons On The Right-Hand Side Of The Control Panel - KETRON SD1 User Manual

If the LED of the PROGRAM push button is lit, the VOICE push buttons call up the Program memories.
If the LED of the ONE TOUCH push button is lit, the first row of STYLE push buttons calls up one of the eight pages of which the One Touch
memories are made up.
If the LEDs of the SET DRUM and MANUAL DRUM push buttons are lit, the first six VOICES push buttons are used to select the banks inclu-
ding ten Drum Kits each.

PUSH BUTTONS ON THE RIGHT-HAND SIDE OF THE CONTROL PANEL

1 TOUCH When the LED is lit, ten timbres of the first of the eight groups available are displayed. The One Touch Solo function is used
to save the most frequently used Voices so that they can be called up easier rather than having to first select the group and
then a timbre from within it.
VOCALIZER EDIT This is used to gain access to the programming parameters of the Vocalizer from the main page.
VOCALIZER ON/OFF When the LED is lit, the Vocalizer is enabled on the Voice or the audio signal sent from input 1 for the microphone
PROGRAM When the LED is lit, eight Program memories are displayed, to be selected using the function push buttons. A program com-
bines up to four timbres dedicated to the lead section with the relative parameters.
2ND VOICE When the LED is lit, the second Voice is enabled on the lead, the timbre of which is displayed under the main one.
2ND VOICE EDIT When the LED is lit it is used to call up a new timbre to replace that set by Ketron for the second voice using the VOICES
push buttons and also from the User Voice group. By pressing 2ND VOICE and 2ND VOICE EDIT at the same time the block
of the timbre assigned at the time to the Second Voice is obtained, which will appear with an asterisk in front of the name.
BLOCK REGISTR. The Registrations control all the SD1 settings, including the automatic call up of audio and TXT files. When the LED is lit the
user can call up one of the 198 Registrations using the numeric keypad, namely the STYLE push buttons. The single
Registration can be loaded directly from hard disk or floppy disk using the SINGLE REGISTR. push button in use.
PIANIST When the LED is lit the chords are acknowledged right along the whole keyboard, including the Right section. This function
has been devised to be able to play freely with two hands and to fully exploit the Arranger potentials. If the same timbre is
required right along the whole keyboard, for example the piano, the Split point is to be moved over to the first note of the
keyboard (E0) using the dedicated push button. There are two different chord acknowledgement methods that can be cho-
sen in the Utility menu. The default setting is Standard.
STYLE SETTING For each style Ketron has foreseen ten settings, enabling just as many timbres to be called up for the Style lead part. When the
LED is lit the ten timbres pre-set for that style are displayed. The attribution between styles and timbres can be modified.
DEMO & HIT By pressing the PIANIST and STYLE SETTING push buttons together at the same time access is gained to the folder of the
hard disk called Demo & Hit, which can store both demo files and any other Midi file for a total of 999 files. On the contrary
to SONG PLAY, Demo & Hit is used to immediately play a Midi file by simply selecting it using the F1-F10 function push but-
tons and it allows a large number of Midi files to be ready to be played. Press EXIT to exit from Demo & Hit. Considering
that Demo & Hit refers to a specific folder of the hard disk, the Midi files within Demo & Hit can be copied and erased with
the normal procedures dedicated to the management of the hard disk. The Right and Lower part can be played while a Midi
file is being reproduced plus the SPLIT push button is also enabled.
# In this version of the operating system this special push button is used together with * to disable the Sustain in the Pianist mode.
* This is situated on the FOLK push button of the STYLES push buttons. It works when the Demo & Hit function is in use
where, when the Midi file selected is Stopped, it is used to put the Midi files within the folder in the desired order with the
possibility of replacing them or cancelling their position. It is also used in SONG PLAY when in the Juke-Box function where,
if it is pressed, the Chain Select command appears to create temporary chains of Midi files to be reproduced one after the
other. Furthermore, in the Pianist enabled mode, when pressed together with the # push button it disables the Sustain.
LEAD The FILL 1 push button has another function when the Demo & Hit function is in use. It is used to cut-out the Lead track,
usually set on the MIDI 4 channel, from the reproduction of the Midi file.
DRUM & BASS The FILL 2 push button has another function when the Demo & Hit function is in use. It mutes the volume of all the tracks
with the exception of the drum and bass ones.
DRUM SET The drum set assigned to the Drum tracks of the style can be changed when the LED is lit. The drum set pages following the
first page can be called up using PAGE +/- or directly using the first six VOICES push buttons. Drum Kit written in capital
letters refers to those made up of ROM samples, those on the other hand with a dot at the side are the sampled grooves,
assigned to the Drum 2 tracks of the style.
10
SD1 Owner's Manual