Page 2 Vigor2130 Series High Speed Gigabit Router User’s Guide Version: 2. 1 Firmware Version: V1.5.2 Date: 21/05/2012 Vigor2130 Series User’s Guide...
Page 3: Copyright Information
Web registration is preferred. You can register your Vigor router via Be a Registered http://www.draytek.com. Owner Due to the continuous evolution of DrayTek technology, all routers will be regularly Firmware & Tools upgraded. Please consult the DrayTek web site for more information on newest Updates firmware, tools and documents.
Page 4: European Community Declarations
Product: Vigor2130 Series Router DrayTek Corp. declares that Vigor2130 Series of routers are in compliance with the following essential requirements and other relevant provisions of R&TTE Directive 1999/5/EEC. The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive 2004/108/EC by complying with the requirements set forth in EN55022/Class B and EN55024/Class B.
Page 5: Table Of Contents
Case 1: VPN direction from Vigor2130 to Vigor2820 .............. 46 Case 2: VPN direction from Vigor2820 to Vigor2130 .............. 50 3.4 How to configure settings for DLNA Service in Vigor2130............ 53 3.5 How to download BT Torrent to USB Device via Vigor Router..........57 Vigor2130 Series User’s Guide...
Page 6 4.7.1 Dynamic DNS ....................... 159 4.7.2 Schedule ........................161 4.7.3 IGMP..........................163 4.7.4 IGMP Status ......................... 164 4.7.5 UPnP Configuration ...................... 164 4.7.6 Wake On LAN....................... 166 4.7.7 Short Message Service....................167 4.8 VPN and Remote Access....................169 Vigor2130 Series User’s Guide...
Page 7 4.15.3 System Password ....................... 254 4.15.4 User Password ......................255 4.15.5 Configuration Backup ....................257 4.15.6 Syslog/Mail Alert ......................259 4.15.7 Time and Date ......................262 4.15.8 Management....................... 263 4.15.9 Reboot System ......................264 4.15.10 Firmware Upgrade ....................264 Vigor2130 Series User’s Guide...
Page 8 5.4 Checking If the ISP Settings are OK or Not ................ 283 5.5 Forcing Vigor Router into TFTP Mode for Performing the Firmware Upgrade ....284 5.6 Backing to Factory Default Setting If Necessary ..............287 5.7 Contacting Your Dealer ....................... 288 viii Vigor2130 Series User’s Guide...
Page 9: Preface
The Vigor2130 series are the routers with high speed in data transmission through WAN port and LAN ports. With hardware NAT acceleration, the rate of Vigor2130 series can be ideal for multi-media application. With the development of NGN (Next Generation Network), you may recently hear the news about FTTx deployment in your local area or even have already subscribed the unbundling last mile service (e.g.
Page 10: Led Indicators And Connectors
The DoS/DDoS function is active. Blinking It will blink while detecting an attack. Interfac Description Connector for accessing the Internet. Connectors for local networked devices. (1/2/3/4) Connector for USB storage device (Pen Driver/Mobile (1/2) HD) or printer or 3G backup. Vigor2130 Series User’s Guide...
Page 11 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connector for a power adapter. Power Switch. ON/OFF Vigor2130 Series User’s Guide...
Page 12: For Vigor2130N
Press the button once to enable (WLAN LED on) or WLAN disable (WLAN LED off) wireless connection. Connector for accessing the Internet. Connectors for local networked devices. (1/2/3/4) USB (1/2) Connector for USB storage device (Pen Driver/Mobile HD) or printer or 3G backup. Vigor2130 Series User’s Guide...
Page 13 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connector for a power adapter. Power Switch. ON/OFF Vigor2130 Series User’s Guide...
Page 14: For Vigor2130Vn
Press the button once to enable (WLAN LED on) or WLAN disable (WLAN LED off) wireless connection. Connector for accessing the Internet. Connectors for local networked devices. (1/2/3/4) USB (1/2) Connector for USB storage device (Pen Driver/Mobile HD) or printer or 3G backup. Vigor2130 Series User’s Guide...
Page 15 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connector for a power adapter. Power Switch. ON/OFF Vigor2130 Series User’s Guide...
Page 16: Hardware Installation
4 PCs directly. Connect Phone port to a conventional analog telephone. Connect detachable antennas to the router for Vigor2130 series (n model). Connect one end of the power cord to the power port of this device. Connect the other end to the wall outlet of electricity.
Page 17: Stand Installation
The Vigor2130 must be placed erectly. Therefore you have to install a stand onto the router to make it standing firmly. Please follow the figures listed below to finish the installation. Vigor2130 Series User’s Guide...
Page 18: Printer Installation
You can install a printer onto the router for sharing printing. All the PCs connected this router can print documents via the router. The example provided here is made based on Windows XP/2000. For Windows 98/SE/Vista, please visit www.draytek.com. Before using it, please follow the steps below to configure settings for connected computers (or wireless clients).
Page 19 Click Local printer attached to this computer and click Next. In this dialog, choose Create a new port Type of port and use the drop down list to select Standard TCP/IP Port. Click Next. Vigor2130 Series User’s Guide...
Page 20 In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer Name or IP Address and type IP_192.168.1.1 as the port name. Then, click Next. Click Standard and choose Generic Network Card. Then, in the following dialog, click Finish. Vigor2130 Series User’s Guide...
Page 21 11. Select "LPR" on Protocol, type p1 (number 1) as Queue Name. Then click OK. Next please refer to the red rectangle for choosing the correct protocol and UPR name. Vigor2130 Series User’s Guide...
Page 22 If you do not know whether your printer is supported or not, please visit www.draytek.com to find out the printer list. Open Support >FAQ; find out the link of Printer Server and click it; then click the What types of printers are compatible with Vigor router? link.
Page 23: Basic Settings
The web page can be logged out according to the chosen condition. The default setting is Auto Logout, which means the web configuration system will logout after 5 minutes without any operation. Change the setting for your necessity. Vigor2130 Series User’s Guide...
Page 24: Changing Password
Note: The home page will change slightly in accordance with the type of the router you have. Go to System Maintenance page and choose System Password. Type a new password in New Password and Confirm New Password fields. Then click OK to continue. Vigor2130 Series User’s Guide...
Page 25: Quick Start Wizard
If your router can be under an environment with high speed NAT, the configuration provide here can help you to deploy and use the router quickly. The first screen of Quick Start Wizard is welcome page, please click Next. Vigor2130 Series User’s Guide...
Page 26: Setting Up The Password
The first screen of Quick Start Wizard is entering login password. After typing the password, please click Next. On the next page as shown below, please select the Time Zone for the router installed and specify the NTP server(s). Then click Next for next step. Vigor2130 Series User’s Guide...
Page 27: Setting Up The Internet Connection
IP, while a DSL service provider will offer a public subnet. If you have a public subnet, you could assign an IP address or many IP address to the WAN interface. Available settings are explained as follows: Item Description Vigor2130 Series User’s Guide...
Page 28 MAC address cloning. It is available when the box of Enable is checked. Click Clone MAC Address Clone PC Address. The result will be displayed in the field of MAC Address. Vigor2130 Series User’s Guide...
Page 29 If you want to connect to Internet all the time, you can Redial Policy choose Always On. Otherwise, choose Connect on Demand. Set the timeout for breaking down the Internet after passing Idle Time Out through the time without any action. Vigor2130 Series User’s Guide...
Page 30 Specify the IP address of the PPTP server. Server Address You can choose Static IP or DHCP as WAN IP network WAN IP Network setting. Settings Type the IP address if you choose Static IP as the WAN IP IP Address network setting. Vigor2130 Series User’s Guide...
Page 31: Setting Up The Wireless Connection
Enable Wireless LAN Choose Show to make the SSID being seen by wireless SSID Broadcast clients. Choose Hide to prevent from wireless sniffing and make it harder for unauthorized clients or STAs to join your wireless LAN. Vigor2130 Series User’s Guide...
Page 32 It means the identification of the wireless LAN. SSID can SSID be any text numbers or various special characters. The default SSID is "DrayTek". We suggest you to change it. Select an appropriate encryption mode to improve the Encryption security and privacy of your wireless data packets.
Page 33 The built-in RADIUS client feature enables the router to assist the remote dial-in user or a wireless station and the RADIUS server in performing mutual authentication. It enables centralized remote access authentication for network management. Vigor2130 Series User’s Guide...
Page 34 The default value is 1812, based on RFC 2138. The RADIUS server and client share a secret that is used to Shared Secret authenticate the messages sent between them. Both sides must be configured to use the same shared secret. Vigor2130 Series User’s Guide...
Page 35 PinCode the router will blink fast when WPS is in progress. It will return to normal condition after two minutes. (You need to setup WPS within two minutes) After finishing the settings here, please click Next. Vigor2130 Series User’s Guide...
Page 36: Saving The Wizard Configuration
If you select PPPoE as the protocol, you will find out a link of Dial PPPoE or Drop PPPoE in the Online Status web page. Detailed explanation is shown below: Item Description IP Address-Displays the IP address of the LAN interface. LAN Status TX Packets-Displays the total transmitted packets at the Vigor2130 Series User’s Guide...
Page 37: Saving Configuration
Each time you click OK on the web page for saving the configuration, you can find messages showing the system interaction with you. Ready indicates the system is ready for you to input settings. Settings Saved means your settings are saved once you click Finish or OK button. Vigor2130 Series User’s Guide...
Page 38: Registering Vigor Router
Please login the web configuration interface of Vigor router by typing “admin/admin” as User Name / Password. Click Support Area>>Production Registration from the home page. A Login page will be shown on the screen. Please type the account and password that you created previously. And click Login. Vigor2130 Series User’s Guide...
Page 39 (it appears when you click on the box of Registration Date). After adding the basic information for the router, please click Submit. When the following page appears, your router information has been added to the database. Vigor2130 Series User’s Guide...
Page 40 If you have not activated web content filter service by using Service Activation Wizard, you can activate the service from this step. Please click the serial number link. From the Device’s Service section, click the Trial. Vigor2130 Series User’s Guide...
Page 41 In the following page, check the box of “I have read and accept the above Agreement”. The system will find out the date for you to activate this version of service. Then, click Next. When this page appears, click Register. Wait for a moment until the following page appears. Click Close. Vigor2130 Series User’s Guide...
Page 42 This page is left blank. Vigor2130 Series User’s Guide...
Page 43: Tutorials And Applications
If the router you have supports VoIP, you can configure VoIP WAN setting for using by VoIP interface of the router. In LAN VLAN setting, check the box of Enable (LAN to WAN in bridge mode) and type a different VLAN ID number. Vigor2130 Series User’s Guide...
Page 44 FXS 1 Phone connects to the FXS 1 port of Vigor2130, registers, sends and receives phone call with VoIP WAN. Functions Configuration 1. Open WAN>>Internet. Set PPPoE as the Connection Type and fill in the Username and Password offered by your ISP. Vigor2130 Series User’s Guide...
Page 45 2. Open WAN>>802.1Q VLAN Tag Configuration to configure Multi-VLAN. Refer to the following graphic. 3. Open WAN>>VoIP WAN to configure VoIP WAN Setting. Note: At present, only DHCP, PPPoE and Static connection types are available. Vigor2130 Series User’s Guide...
Page 46 4. Open VoIP >>SIP Accounts. Specify the connection interface for VoIP in the field of Register via. 5. Connect your PC or network device to the forth LAN port and type the username and password for PPPoE connection mode. Vigor2130 Series User’s Guide...
Page 47: Lan To Lan Ipsec Vpn Between Vigor2130 And Vigor2820 Using Main Mode
Enable it and give it a name. In this example the profile name is “Demo”. Enter Vigor2820’s WAN IP address in the Remote IP field. Select Main Mode as IKE phase 1 mode. Setup a pre-shared key, which must be the same as in Vigor2820. Vigor2130 Series User’s Guide...
Page 48 Accessing the VPN network of Vigor2820 from a PC behind Vigor2130 to initiate the VPN connection, for example, ping 192.168.1.x from a PC (192.168.30.x). Vigor2130 will be triggered to dial the IPSec VPN to Vigor2820. After the VPN is connected, you can monitor the status. Vigor2130 Series User’s Guide...
Page 49 In Dial-Out Settings part, select IPSec Tunnel and press the Advanced button. In Dial-In Settings part, please enable Specify Remote VPN Gateway and enter WAN IP address of Vigor2130 in the Peer VPN Server ID field. Vigor2130 Series User’s Guide...
Page 50 3DES, MD5; 3DES, SHA1; When you select AES(any) AES-256, MD5; AES-256, SHA1; When you select AES-128 AES-128, MD5; AES-128, SHA1; When you select AES-192 AES-192, MD5; AES-192, SHA1; When you select AES-256 AES-256, MD5; AES-256, SHA1; Vigor2130 Series User’s Guide...
Page 51: Case 2: Vpn Direction From Vigor2820 To Vigor2130
Enter Vigor2130’s private network in the Local Network / Mask field. Enter Vigor2820’s private network in the Remote Network / Mask field. Use default value “Automatic” for IKE phase 1 and phase 2 proposals. After the VPN is connected, you can monitor the status. Vigor2130 Series User’s Guide...
Page 52 Create a LAN-to-LAN profile. Enable it and give it a name. In this example the profile name is “test”. Vigor2130 Series User’s Guide...
Page 53 Name for VPN field. Setup a pre-shared key, which must be the same as in Vigor2130. Select ESP (High) and 3DES with Authentication. Enter Vigor2130’s private network in the Remote Network IP / Mask field. Click OK. Vigor2130 Series User’s Guide...
Page 54: Lan To Lan Ipsec Vpn Between Vigor2130 And Vigor2820 Using Agressive Mode
Create a LAN-to-LAN profile. Enable it and give it a name. In this example the profile name is “Demo”. Enter Vigor2820’s WAN IP address in the Remote IP field. Select Aggressive Mode as IKE phase 1 mode. Vigor2130 Series User’s Guide...
Page 55 10. Accessing the VPN network of Vigor2820 from a PC behind Vigor2130 to initiate the VPN connection, for example, ping 192.168.1.x from a PC (192.168.30.x). Vigor2130 will be triggered to dial the IPSec VPN to Vigor2820. After the VPN is connected, you can monitor the status. Vigor2130 Series User’s Guide...
Page 56 Create a LAN-to-LAN profile. Enable it and give it a name. In this example the profile name is “test”. Vigor2130 Series User’s Guide...
Page 57 3DES, MD5; 3DES, SHA1 When you select AES(any) AES-256, MD5; AES-256, SHA1 When you select AES-128 AES-128, MD5; AES-128, SHA1 When you select AES-192 AES-192, MD5; AES-192, SHA1 When you select AES-256 AES-256, MD5; AES-256, SHA1 Vigor2130 Series User’s Guide...
Page 58: Case 2: Vpn Direction From Vigor2820 To Vigor2130
Enter Vigor2130’s private network in the Local Network / Mask field. Enter Vigor2820’s private network in the Remote Network / Mask field. Use default value “Automatic” for IKE phase 1 and phase 2 proposals. 10. After the VPN is connected, you can monitor the status. Vigor2130 Series User’s Guide...
Page 59 Create a LAN-to-LAN profile. Vigor2130 Series User’s Guide...
Page 60 DES_SHA1_G2/3DES_MD5_G2/3DES_SHA1_G2” as IKE phase 1 proposal. Enter vigor2820 in the Local ID field. Click OK to return to the profile setting page. Enter Vigor2130’s private network in the Remote Network IP / Mask field. 10. Click OK. Vigor2130 Series User’s Guide...
Page 61: How To Configure Settings For Dlna Service In Vigor2130
Insert USB storage device into the USB slot of Vigor2130. Then, open USB Application>>Disk Status to check the connection status. If it is connected successfully, the general information of that device will be shown on the screen. Vigor2130 Series User’s Guide...
Page 62 During the process of installation, you can click Show Detail to view the installation procedure. After finished the service installation, the configuration page will be open automatically. Please click Enable and type a name in the field of Server Name. Then, click OK to activate DLNA service. Vigor2130 Series User’s Guide...
Page 63 Server Name configured in Step 4. Note: If you cannot see the media device in Network view, please check and make sure the UPnP service has been enabled Control Panel>>Administrative Tools >>Services. Vigor2130 Series User’s Guide...
Page 64 Before removing USB storage device, please DISABLE DLNA service and then remove the device. The audio and video files might not be played normally due to unrecognized equipment set in client. Vigor2130 Series User’s Guide...
Page 65: How To Download Bt Torrent To Usb Device Via Vigor Router
Wait for few seconds for the router to detect it. If the disk is detected, it will be shown as the following figure. Make sure that WAN connection has been established. Open USB Application >> Bit Torrent Download. Click Install to install BT module from Internet to USB device. Vigor2130 Series User’s Guide...
Page 66 Simply wait for a few minutes to finish the installation. When the installation is finished, the following page will be displayed. Click the link of Open Web Client to open another window. Vigor2130 Series User’s Guide...
Page 67 10. Click Select File to open the following dialog. Choose the seed of BT torrent file and click Open. Note: Before uploading torrent files to the router, please search from Internet and store the seed of the BT torrent on our hard disk first. Vigor2130 Series User’s Guide...
Page 68 Access into Vigor2130 web configuration interface and open USB Application >> USB General Settings. Enable the Disk Sharing function by checking the box and click OK. Open USB Application >> Disk Shares. Click Add a New Entry. Vigor2130 Series User’s Guide...
Page 69 Share Name for home folder (“/”) . Click OK. Now, PCs in LAN connected to Vigor2130 can open a browser from his / her computer. Simply type “\\192.168.1.1” in the field of Address and then click Go. Vigor2130 Series User’s Guide...
Page 70 The sharing disk with the name of “bt_folder” created above will be shown as the following figure. Double click bt_folder to view the files in the disk. Vigor2130 Series User’s Guide...
Page 71 If you want to check the BT Torrent files downloaded from Internet to USB disk, access into bt_folder>>downloads. (Note: While the file is downloading, the file extension name will be “part”.) Vigor2130 Series User’s Guide...
Page 72 Vigor2130. Go to http://freedns.afraid.org/dynamic/ and login with your normal username and password for the FreeDNS service. Click Direct URL on the domain, you would like to set to your WAN IP address. Vigor2130 Series User’s Guide...
Page 73 Past the strings what you copied on step3 on password field. Click OK to save the configuration. Now, you can check the service by using nslookup command on your computer or check the syslog information on Vigor2130. Vigor2130 Series User’s Guide...
Page 74 This page is left blank. Vigor2130 Series User’s Guide...
Page 75: Web Configuration
Hence, the NIC has reserved certain addresses that will never be registered publicly. These are known as private IP addresses, and are listed in the following ranges: Vigor2130 Series User’s Guide...
Page 76 After connecting into the router, 3G USB Modem will be regarded as the backup WAN port. Therefore, when WAN is not available, the router will use 3.5G for supporting automatically. The supported 3G USB Modem will be listed on DrayTek web site. Please visit www.draytek.com for more detailed information.
Page 77: Internet Access
WAN IP Alias - If you have multiple public IP addresses and would like to utilize them on the WAN interface, please use WAN IP Alias. You can set up to 8 public IP addresses other than the current one you are using. Such function can Vigor2130 Series User’s Guide...
Page 78 If you have a public subnet, you could assign an IP address or many IP address to the WAN interface. To use Static as the accessing protocol of the internet, please choose Static mode from Connection Type drop down menu. The following web page will be shown. Vigor2130 Series User’s Guide...
Page 79 Detection Detect. Choose ARP Detect or Ping Detect for the system to execute for WAN detection. Ping IP-If you choose Ping Detect as detection mode, you have to type IP address in this field for pinging. Vigor2130 Series User’s Guide...
Page 80 DHCP allows a user to obtain an IP address automatically from a DHCP server on the Internet. If you choose DHCP mode, the DHCP server of your ISP will assign a dynamic IP address for your router automatically. It is not necessary for you to assign any setting, Vigor2130 Series User’s Guide...
Page 81 Router Name -Type in a name for the router. It must be the DHCP Settings same as the name used in Syslog. Domain Name -Type the domain name (e.g., draytek) to fit the request of some ISPs. MTU Size -It means Max Transmit Unit for packet. The default setting will be specified by the system automatically.
Page 82 Internet after passing through the time without any action. When you choose Connect on Demand, you have to type value here. MTU Size - It means Max Transmit Unit for packet. The default setting will be specified by the system automatically. Vigor2130 Series User’s Guide...
Page 83 Event types – Specify the event when the system must send a notification to the user by mail and/or SMS. After finishing all the settings here, please click OK to activate them. Vigor2130 Series User’s Guide...
Page 84 WAN IP network setting. Subnet Mask -Type the subnet mask if you chose Static IP as the WAN IP. Specify Gateway IP Address – Type gateway IP address. Primary DNS Server-You must specify a DNS server IP Vigor2130 Series User’s Guide...
Page 85 Clone MAC Address. The result will be displayed in the field of MAC Address. Alert Types – Specify the type of the alert (mail, SMS, or Mail/SMS Alert Mail and SMS) that Vigor system will use to send a message to the user. Vigor2130 Series User’s Guide...
Page 86 Event types – Specify the event when the system must send a notification to the user by mail and/or SMS. After finishing all the settings here, please click OK to activate them. Vigor2130 Series User’s Guide...
Page 87 Modem Dial String-Such value is used to dial through USB mode. Please use the default value. If you have any question, please contact to your ISP. PPP Username-Type the PPP username (optional). PPP Password-Type the PPP password (optional). Vigor2130 Series User’s Guide...
Page 88 Event types – Specify the event when the system must send a notification to the user by mail and/or SMS. After finishing all the settings here, please click OK to activate them. Vigor2130 Series User’s Guide...
Page 89 IP address in this field for pinging. Clone MAC Address Enable – Enable the feature. It is available when the box of Enable is checked. Click Clone MAC Address. The result will be displayed in the field of MAC Address. Vigor2130 Series User’s Guide...
Page 90 Network Mode – Choose the connection mode for network. You can use 4G only for connection, 3G only for connection, 2G only for connection or 4G/3G/2G (specified by the router system automatically). The default setting is 4G/3G/2G. Vigor2130 Series User’s Guide...
Page 91 Mail/SMS Alert Mail and SMS) that Vigor system will use to send a message to the user. Event types – Specify the event when the system must send a notification to the user by mail and/or SMS. Vigor2130 Series User’s Guide...
Page 92: Multi-Vlan
Vigor2130 series offers multi-VLAN function to make the data transmission with security. Data transmitting through the Ethernet port for connecting to Internet can be tagged with an ID number specified here for ensuring the security. In addition, each LAN port also can be tagged with an ID number in local network to reach the goal of protection.
Page 93 Public IP address from ISP for transmitting data from PC directly without NAT. The range of ID number you can type is from 2 – 4096. Each ID setting must be unique and different with WAN VLAN ID. Vigor2130 Series User’s Guide...
Page 94 Event types – Specify the event when the system must send a notification to the user by mail and/or SMS. When DHCP is selected as connection type, you need to configure the following settings: Vigor2130 Series User’s Guide...
Page 95 Event types – Specify the event when the system must send a notification to the user by mail and/or SMS. When PPPoE is selected as connection type, you need to configure the following settings: Vigor2130 Series User’s Guide...
Page 96: Ports
Current - It displays current speed that the router uses. Speed Configured - You can use the drop down list to choose the required speed for the router. If you have no idea in configuring speed, simple use the default setting, Auto. Vigor2130 Series User’s Guide...
Page 97 Disabled: All power savings mechanisms disabled. ActiPHY: Link down power savings enabled. PerfectReach: Link up power savings enabled. Enabled: Both link up and link down power savings enabled. Click this button to refresh the information for WAN port. Refresh Vigor2130 Series User’s Guide...
Page 98: Backup
APN Name - APN means Access Point Name which is provided and required by some ISPs. Modem Dial String - Such value is used to dial through USB mode. Please use the default value. If you have any Vigor2130 Series User’s Guide...
Page 99 When the WAN connection is broken, router will try to keep the connection with 56K mode if it is enabled. After WAN connection is recovered, router will disconnect the 56K connection automatically. Available settings are explained as follows: Vigor2130 Series User’s Guide...
Page 100 Mail and SMS) that Vigor system will use to send a message to the user. Event types – Specify the event when the system must send a notification to the user by mail and/or SMS. Click it to reset the USB device. Reset USB Vigor2130 Series User’s Guide...
Page 101: Lan
IP address. As a part of the public subnet, the Vigor router will serve for IP routing to help hosts in the public subnet to communicate with other public hosts or servers outside. Therefore, the router should be set as the gateway for public hosts. Vigor2130 Series User’s Guide...
Page 102 You can group local hosts by physical ports and create up to 4 virtual LANs. To manage the communication between different groups, please set up rules in Virtual LAN (VLAN) function and the rate of each. Vigor2130 Series User’s Guide...
Page 103: General Setup
WAN server. Thus, the PC can access Internet through such direction. Enable Server - DHCP stands for Dynamic Host DHCP Server Configuration Protocol. The router by factory default acts a Configuration DHCP server for your network so it automatically dispatch Vigor2130 Series User’s Guide...
Page 104 Otherwise, the router forwards the DNS query packet to the external DNS server by establishing a WAN (e.g. DSL/Cable) connection. After finishing all the settings here, please click OK to activate them. Vigor2130 Series User’s Guide...
Page 105: Ports
Current Tx: indicates whether pause frames on the port are transmitted. This module offers 1518~9600 (Bytes) length to make the Maximum Frame long packet for data transmission. There are two modes for you to choose when excessive Excessive Collision Mode collision happened in half-duplex condition. Vigor2130 Series User’s Guide...
Page 106 PerfectReach: Link up power savings enabled. Enabled: Both link up and link down power savings enabled. Click this button to refresh the information for LAN port. Refresh After finishing all the settings here, please click OK to activate them. Vigor2130 Series User’s Guide...
Page 107: Mac Address Table
MAC Address - It is a six-byte long Ethernet hardware address and usually expressed by hex and separated by hyphens. For example, 00 – 40 - C7 - D6 – 00 – 02. WAN/LAN1~4 - Check the port to apply this VLAN Vigor2130 Series User’s Guide...
Page 108: Vlan
To add or remove a VLAN, please refer to the following example. VLAN 1 is consisted of hosts linked to P1 ~ P4. After checking the box to enable VLAN function, you will check the table according to the needs as shown below. Vigor2130 Series User’s Guide...
Page 109: Monitor Port
Monitor ingress port monitors the packets received by the port you set up. Check to set up the port(s) for being monitored. It only Monitor egress port monitors the packets transmitted by the port you set up. Vigor2130 Series User’s Guide...
Page 110: Static Route
Main Router 192.168.1.1 as the default gateway for the Router A 192.168.1.2. Before setting Static Route, user A cannot talk to user B for Router A can only forward recognized packets to its default gateway Main Router. Vigor2130 Series User’s Guide...
Page 111 192.168.10.0 will be forwarded to 192.168.1.2. Click OK. Return to Static Route page. Click Add again to add another static route as show below, which regulates all packets destined to 211.100.88.0 will be forwarded to 192.168.1.3. Vigor2130 Series User’s Guide...
Page 112: Police Route
Gateway Display the interface used by such policy route. Interface Display if NAT is done for source subnet or not. Display the status of the static route. Status Click it to add a new static route. Vigor2130 Series User’s Guide...
Page 113: Bind Ip To Mac
When this function is enabled, all the assigned IP and MAC address binding together cannot be changed. If you modified the binding IP or MAC address, it might cause you not access into the Internet. Click LAN and click Bind IP to MAC to open the setup page. Vigor2130 Series User’s Guide...
Page 114 Comment – Type a brief description for the entry. Show Comment – Check it to display the content of the comment. Web Portal – Default means the user needs to type username and password for accessing into the Internet through web logging. Vigor2130 Series User’s Guide...
Page 115 Note: Before you select Strict Bind, you have to bind one set of IP/MAC address for one PC. If not, no one of the PCs can access into Internet. And the web configurator of the router might not be accessed. Click OK to save the settings. Vigor2130 Series User’s Guide...
Page 116: Web Portal
However, the login page will be shown in HTTP format and can run under different browser without the trouble of compatibility. Enable (HTTPS) – Click it to enable the function of web portal. However, the login page will be shown in HTTPS Vigor2130 Series User’s Guide...
Page 117 Logout after shutdown - If it is checked, the system will terminate the web accessing job after shutdown the computer. Type a brief description (e.g., Welcome to DrayTek) which Welcome Message will be shown on the heading of the login dialog.
Page 118 Redirect. When the web portal is enabled, a green light will be displayed on the top of the page. When the web portal is disabled, a red light will be displayed. Below shows an example of web portal page with the information typed in Welcome Message and Bulletin. Vigor2130 Series User’s Guide...
Page 119: Nat
192.168.1.0/24 subnet for the router. As stated before, the NAT facility can map one or more IP addresses and/or service ports into different specified services. In other words, the NAT function can be achieved by using port mapping methods. Below shows the menu items for NAT. Vigor2130 Series User’s Guide...
Page 120: Hardware Nat
Hardware-base Acceleration Engine, also named Protocol Processing Engine API is the function that DrayTek provides to extremely speed up the NAT performance. While the hardware acceleration mechanism is activated, most of the bandwidth usage will be concentrated on the specific sessions which increase transmission speed to get ultimately accelerated.
Page 121 Enter the private IP address of the local host. Local Host If it is configured, the forwarded traffic is mapped to this Local Port (optional) port on the local host. Click OK to save the settings. Vigor2130 Series User’s Guide...
Page 122: Dmz Host
Check to enable the DMZ Host function. Enable Such option is available when WAN IP Alias has been Aux. WAN IP configured. Enter the private IP address of the DMZ host, or click Private IP Choose PC to specify a suitable one. Vigor2130 Series User’s Guide...
Page 123: Firewall
Vigor router will activate its defense mechanism to mitigate in a real-time manner. Below shows the menu items for Firewall. Click Firewall and click DoS Defense to open the setup page. Available settings are explained as follows: Vigor2130 Series User’s Guide...
Page 124: Ports Configuration
Select whether forwarding is permitted ("Allow") or denied Action ("Deny"). The default value is "Allow". Select a rate limiter to apply to this port. Available settings Rate Limiter ID include Disabled, and 1 to 10. The default value is Vigor2130 Series User’s Guide...
Page 125 Rate limiter ID will be applied to WAN port and LAN port. Rate Limiter ID Please specify a rate number for each ID. The default setting is “1”(packet per second). Define the rate by choosing from the following drop down Rate Vigor2130 Series User’s Guide...
Page 126 Click OK to save the settings. Vigor2130 Series User’s Guide...
Page 127: Access Control List
Ingress Port – define which port the packet coming from. ACE Configuration The policy IDs are defined in Firewall>>Port Configuration. Each Policy ID might have more than one port grouped. Frame Type - Such option differs according to the Vigor2130 Series User’s Guide...
Page 128 Frame Type you select. When you finish the setting, click OK to save the settings. A new ACL profile is created. You can click to open the selected profile for any modification; click to delete the selected profile. Vigor2130 Series User’s Guide...
Page 129 (the range is 0x0000 to 0xFFFF). Choose ARP as the Frame Type, you will get ARP Parameters option as the following: Available settings are explained as follows: Item Description Choose the ARP/RARP that you want to filter. ARP/RARP Vigor2130 Series User’s Guide...
Page 130 Network as Target IP Filter. Specify whether frames/packets can meet the action ARP SMAC Match according to the sender hardware address field (SHA) settings. 0: means sender hardware address is not equal to the SMAC Vigor2130 Series User’s Guide...
Page 131 1: ARP/RARP frames where the hardware address space is equal to Ethernet (1) must match this entry. Any: Any value is allowed. Specify whether frames can hit the action according to their Ethernet ARP/RARP protocol address space (PRO) settings. Vigor2130 Series User’s Guide...
Page 132 Host or Network as Source IP. Type the Source IP Mask here. This option is available only Source IP Mask when you choose Network as source Source IP. Specify the destination IP filter for this ACE. Dest IP Filter Vigor2130 Series User’s Guide...
Page 133 0 to 255. A frame meeting this ACE matches this ICMP value. Choose IPv4 as the Frame Type. You will see IP Parameters on the bottom of the page. If you choose UDP as IP Protocol Filter, you will get the page as the following: Vigor2130 Series User’s Guide...
Page 134 Type the destination IP Address here. This option is Dest IP Address available when you choose Host or Network as destination Type the DIP Mask here. This option is available only when Dest IP Mask you choose Network as destination DIP. Vigor2130 Series User’s Guide...
Page 135 ACE matches this UDP source value. Type the value if you choose Range as the Dest. Port Filter. Dest. Port Range The allowed range is 0 to 65535. A frame meeting this ACE matches this UDP source value. Vigor2130 Series User’s Guide...
Page 136 IP address in the destination IP Address field that appears. Network: Destination IP filter is set to Network. Specify the destination IP address and destination IP mask in the destination IP Address and destination IP Mask fields that appear. Vigor2130 Series User’s Guide...
Page 137 Type the value if you choose Range as the Dest. Port filter. Dest. Port Range The allowed range is 0 to 65535. A frame meeting this ACE matches this TCP source value. Specify the TCP "No more data from sender" (FIN) value TCP FIN for this ACE. Vigor2130 Series User’s Guide...
Page 138 1: TCP frames where the PSH field is set must be able to match this entry. Any: Any value is allowed. Specify the TCP "Acknowledgment field significant" TCP ACK (ACK) value for this ACE. Vigor2130 Series User’s Guide...
Page 139 “255”.A frame meeting this ACE matches this IP protocol value. Specify the source IP filter for this ACE. Source IP Any: No source IP filter is specified. Host: Source IP filter is set to Host. Specify the source IP Vigor2130 Series User’s Guide...
Page 140: Traffic Control
Available settings are explained as follows: Item Description Check the box to enable such function. Enable Traffic Control Click it add a new firewall rule. Add Entry Vigor2130 Series User’s Guide...
Page 141 Source Address / LAN interface specified in Source / Destination fields. Destination Address Note that the format for this field must be “address[/mask]”, e.g, 192.168.1.123 or 172.16.9.0/24. Specify the MAC address for the packets. Source MAC Address Vigor2130 Series User’s Guide...
Page 142 The method to configure the time object is that same as set in Firewall>>Time Object. Click OK to save the settings. The new added traffic control profile will be shown as follows. Vigor2130 Series User’s Guide...
Page 143: Time Object
Or, click All Day to specify the whole day as time setting. Specify which days in one week should perform the Weekday schedule. Clear – Check the box to clear all the days selected. All – Check the box to select all days. Vigor2130 Series User’s Guide...
Page 144: Csm
ActiveX, Java Applet, Proxy, and so on. In addition, Vigor router allows you to filter certain host specified with IP address. Note: The priority of URL content filters is higher than Web Content Filter. Available settings are explained as follows: Item Description Vigor2130 Series User’s Guide...
Page 145 After pressing OK, it will be filtered whenever you visit. Type the host name of URL for filtering. Click Add a New Web Host Filter Setting Entry to add the host name of URL one by one. Vigor2130 Series User’s Guide...
Page 146: Web Content Filter
Check this box and click OK to enable the button of Add a Enable New Entry. Click it to display the BPjM license information. License Information Click it to activate the WCF service. Activate Display the profile name for WCF service. Name Vigor2130 Series User’s Guide...
Page 147 You can create another one by clicking the link of New Time Object. Display current used WCF mechanism. Status Check the box to make such item filtered by this profile. Youth Protection Vigor2130 Series User’s Guide...
Page 148 Commtouch service, please return to web configurator of Vigor router. Refresh this page and the following screen will appear. Each item is explained as follows: Item Description Check the box to enable the web content filter. Enable Vigor2130 Series User’s Guide...
Page 149 Filter Https supported by Commtouch only. Display the used time object. Time Check the box of Enable and click OK. The Add a New Entry button will be available for you to create a new entry. Vigor2130 Series User’s Guide...
Page 150 Name Click it to enable such profile. Enable Type the IP address with mask address Source IP (e.g.,192.168.1.0/255.255.255.0 to indicate a network or type 192.168.1.10/255.255.255.255 to indicate a single IP) to be filtered by WCF mechanism. Vigor2130 Series User’s Guide...
Page 151: App Enforcement
You are allowed to add many firewall rules for your request. Simply click Add Entry, the following screen will be shown. There are four tabs IM, P2P, Protocol and Misc displayed on this page. Each tab will bring out different items that you can choose to disallow/allow people using. Vigor2130 Series User’s Guide...
Page 152 Block – Packets matching with such rule will be blocked by Action the router. Pass – Packets matching with such rule are allowed to pass through the router. Check this box to record the information on Syslog. Syslog Vigor2130 Series User’s Guide...
Page 153: Bandwidth Management
To solve the problem, you can use limit session to limit the session procession for specified Hosts. In the Bandwidth Management menu, click Sessions Limit to open the web page. Vigor2130 Series User’s Guide...
Page 154 Adds the specific session limitation onto the list above. Allows you to edit the settings for the selected limitation. Edit Remove the selected settings existing on the limitation list. Delete When you finish adding a new session limit, simply click OK. Vigor2130 Series User’s Guide...
Page 155: Bandwidth Limit
Click this button to activate the function of limit bandwidth. Enable Default TX limit - Define the default speed of the upstream for each computer in LAN. Default RX limit - Define the default speed of the downstream for each computer in LAN. Vigor2130 Series User’s Guide...
Page 156 TX limit - Define the default speed of the upstream for each computer in LAN. RX limit - Define the default speed of the downstream for each computer in LAN. When you finish adding a new bandwidth limit, click OK. Vigor2130 Series User’s Guide...
Page 157: Port Rate Control
Another reason is due to congestions at network intersections where speeds of interconnected circuits mismatch or traffic aggregates, packets will queue up and traffic can be throttled back to a lower speed. If there’s no defined priority to specify which packets should be discarded Vigor2130 Series User’s Guide...
Page 158 SLA among different DS domain owners. It’s not easy to achieve deterministic and consistent high-priority QoS traffic throughout the whole network with merely Vigor router’s effort. In the Bandwidth Management menu, click QoS Control List to open the web page. Vigor2130 Series User’s Guide...
Page 159 QCE for the selected QCL. Different QCE type will bring out different web settings. If you choose Ethernet Type as QCE Type, you have to type value for it and specify traffic class from Low, Normal, Medium and High. Vigor2130 Series User’s Guide...
Page 160 Specify traffic class from Low, Normal, Medium and High. Traffic Class If you choose TCP/UDP Port as QCE Type, you have to type the port number for it and specify traffic class from Low, Normal, Medium and High. Vigor2130 Series User’s Guide...
Page 161 IPv4/IPv6 value (6 bits) against the two DSCP values in QCE. Specify traffic class from Low, Normal, Medium and High. Traffic Class If you choose ToS as QCE Type, you have to specify priority class from Low, Normal, Medium and High. Vigor2130 Series User’s Guide...
Page 162 Class values in QCE. Tag Priority 7 Class Specify traffic class from Low, Normal, Medium and High. Traffic Class When you finish the setting, click OK to save the settings. A new ACL profile will be added. Vigor2130 Series User’s Guide...
Page 163: Ports Priority
Use the drop down list to choose the priority for each port. Default Class Use the drop down list to choose the QCL number defined QCL (QoS Control List ) in QoS Control List for the port. Vigor2130 Series User’s Guide...
Page 164: Qos Statistics
Queuing Weighted weighted number. Click OK to save the settings. This page displays statistics for QoS setting. Click WAN/LAN link to check detailed information for each interface. Click WAN/LAN1/LAN2/LAN3/LAN4 link to check detailed information for each interface. Vigor2130 Series User’s Guide...
Page 165 RX 128-255 Bytes bad packets received. Display the number of 256 ~ 511-byte frames in good and RX 256-511 Bytes bad packets received. Display the number of 512 ~ 1023-byte frames in good and RX 512-1023 Bytes Vigor2130 Series User’s Guide...
Page 166 Tx 128-255 Bytes bad packets transmitted. Display the number of 256 ~ 511-byte frames in good and Tx 256-511 Bytes bad packets transmitted. Display the number of 512 ~ 1023-byte frames in good and Tx 512-1023 Bytes Vigor2130 Series User’s Guide...
Page 167: Applications
DDNS service providers such as www.dyndns.org, www.no-ip.com, www.dtdns.com, www.changeip.com, www.dynamic- nameserver.com. You should visit their websites to register your own domain name for the router. Open Applications>>Dynamic DNS to get the following page. Vigor2130 Series User’s Guide...
Page 168 Type in the login name that you set for applying domain. Username Type in the password that you set for applying domain. Password Determine the IP source for DDNS server. IP Source Vigor2130 Series User’s Guide...
Page 169: Schedule
You can inquiry an NTP server (a time server) on the Internet to synchronize the router’s clock. This method can only be applied when the WAN connection has been built up. You can set up to 15 schedules. Click Add to open the following page to create a new schedule profile. Vigor2130 Series User’s Guide...
Page 170 Specify how often the schedule will be applied: Acts Once -The schedule will be applied just once. Routine /Weekday -Specify which days in one week should perform the schedule. Vigor2130 Series User’s Guide...
Page 171: Igmp
IGMP Proxy Channel – Such function is selected for WAN>>Multi-VLAN. If IPTV WAN or VoIP WAN is not configured in WAN>>Multi-VLAN, you have to choose WAN as IGMP Proxy Channel. Vigor2130 Series User’s Guide...
Page 172: Igmp Status
PC peripherals with the existing Windows 'Plug and Play' system. For NAT routers, the major feature of UPnP on the router is “NAT Traversal”. This enables applications inside Vigor2130 Series User’s Guide...
Page 173 The screenshots below show examples of this facility. The UPnP facility on the router enables UPnP aware applications such as MSN Messenger to discover what are behind a NAT router. The application will also learn the external IP address Vigor2130 Series User’s Guide...
Page 174: Wake On Lan
Wake On LAN of this router. In addition, such PC must have installed a network card supporting WOL function. By the way, WOL function must be set as “Enable” on the BIOS setting. Vigor2130 Series User’s Guide...
Page 175: Short Message Service
Vigor router allows you to set up to 8 SMS profiles which will be sent out according to different conditions. To add a new SMS profile, please click Add to open the following web page. Vigor2130 Series User’s Guide...
Page 176 SMS notification just for once. Type a brief description which will be sent to the receiver User-defined when such profile is enabled and selected. Message Send one SMS to the user just for test. Send a test Message Vigor2130 Series User’s Guide...
Page 177: Vpn And Remote Access
LAN, you should enable IPSec VPN Pass-through and specify an IP address to allow VPN tunnel pass through. Available settings are explained as follows: Item Description If this checkbox is checked, the system firewall will allow Enable IPSec VPN VPN (IPSec) remote access from WAN side to the router. Service Vigor2130 Series User’s Guide...
Page 178: Pptp Remote Dial-In
You can manage remote access by maintaining a table of remote user profile, so that users can be authenticated to dial-in via VPN connection. The router provides access accounts for dial-in users. Note: This page is similar to the page under User>>User Configuration. Vigor2130 Series User’s Guide...
Page 179 Remote Network / Mask will travel through the VPN tunnel. Type the address(es) if LAN to LAN is selected as Dial-In Type. Remote Network / Mask –Add a static route to direct all Vigor2130 Series User’s Guide...
Page 180 To edit a user, click the name link under Username to open the following page. Modify the settings except Username and then click OK to save and exit it. If you want to remove such user settings, simply click Delete User. Vigor2130 Series User’s Guide...
Page 181: Ipsec Remote Dial-In
L2TP/IPSec –The range must not overlap the DHCP address range (if enabled), and must allow for at least one IP address. Example: 10.10.137.240-10.10.137.245. If you choose this type, please specify the IP address range for L2TP/IPSec mode. Vigor2130 Series User’s Guide...
Page 182 Phase 2 (IPSec) - Negotiation IPSec security methods including Authentication Header (AH) or Encapsulating Security Payload (ESP) for the following IKE exchange and mutual examination of the secure tunnel establishment. Vigor2130 Series User’s Guide...
Page 183: Remote Dial-In Status
VPN tunnel. Display the dial-in user account. User Name Display the connection name assigned by the router. Interface Display IP address of remote client. Remote IP Display the given local IP address of a client. Local IP Vigor2130 Series User’s Guide...
Page 184: Lan To Lan
Display the data transmission packets / bytes through VPN Tx Packets / Tx Bytes tunnel (by IPSec or PPTP). Display the data receiving packets / bytes through VPN Rx Packets / Rx Bytes tunnel (by IPSec or PPTP). Vigor2130 Series User’s Guide...
Page 185 Display the duration time of the IPSec / PPTP connection. Up Time Click it to add a new VPN tunnel via IPSec / PPTP protocol. Add Tunnel Click Add Tunnel to open the following page. Vigor2130 Series User’s Guide...
Page 186 Network Mask through the VPN connection. For IPSec, this is the destination clients IDs of phase 2 quick mode. Change default route to this VPN tunnel – Check the box to change the default route to this configured VPN tunnel. Vigor2130 Series User’s Guide...
Page 187 You may specify a value in between 600 and 86400 seconds. Perfect Forward Secrecy - The IKE Phase 1 key will be reused to avoid the computation complexity in phase 2. The default value is inactive this function. Click OK to save the settings. Vigor2130 Series User’s Guide...
Page 188 Remote Network / Mask will travel through the VPN tunnel. Remote Network / Mask - Add a static route to direct all traffic destined to this Remote Network IP Address/Remote Network Mask through the VPN connection. Vigor2130 Series User’s Guide...
Page 189: Certificate Management
Here you can generate and manage the local digital certificates, and set trusted CA certificates. Remember to adjust the time of Vigor router before using the certificate so that you can get the correct valid period of certificate. Below shows the menu items for Certificate Management. Vigor2130 Series User’s Guide...
Page 190: Trusted Ca Certificate
Valid From - Display the starting time for the valid Root Expires - Display the ending time for the valid Root CA. Status - Display if such certificate is Active or not. Build RootCA - Allow to build user-defined Root CA certificate. Vigor2130 Series User’s Guide...
Page 191 After pasting the data in this field, simply click Upload below. The related data will be uploaded onto the router. Upload – After pasting the information, click it to upload the CA data coming from the third-party to Vigor router. Vigor2130 Series User’s Guide...
Page 192 Common Name - Type a common name for such certificate. Email address - Type an email address for the system to send any information for you. After finished the page, click OK to save the settings. Vigor2130 Series User’s Guide...
Page 193: Local Certificate
Next, import the issued information in this page to be the local certificate for network connection. Allows you to import a certificate which has been issued by IMPORT Trusted CA Certificate. Click GENERATE to open the following page: Vigor2130 Series User’s Guide...
Page 194 Organization Unit - Type the department or unit for your company. Common Name - Type a common name. Email address - Type an email address for the system to send any information for you. Click OK to save the settings and return to previous page. Vigor2130 Series User’s Guide...
Page 195: Issue Certificate
WLAN users can simultaneously access all LAN facilities just like on a wired LAN as well as Internet access The Vigor wireless routers are equipped with a wireless LAN interface compliant with the standard IEEE 802.11n draft 2 protocol. To boost its performance further, the Vigor Router is Vigor2130 Series User’s Guide...
Page 196 /or privacy on your wireless network. The Vigor wireless router is very flexible and can support multiple secure connections with both WEP and WPA at the same time. Below shows the menu items for Wireless LAN. Vigor2130 Series User’s Guide...
Page 197: General Setup
Enable Wireless LAN - Check the box to enable the General Setting wireless function. Show/Hide- Choose Show to make the SSID being seen by wireless clients. Choose Hide to prevent from wireless sniffing and make it Vigor2130 Series User’s Guide...
Page 198 SSID- It means the identification of the wireless LAN. SSID can be any text numbers or various special characters. The default SSID is "DrayTek". We suggest you to change it. Isolate LAN- Check this box to make the wireless clients (stations) not accessing the PC with wired connection.
Page 199 The format of WEP Key is restricted to 5 ASCII characters or 10 hexadecimal values in 64-bit encryption level, or restricted to 13 ASCII characters or 26 hexadecimal values in 128-bit encryption level. The allowed content is the ASCII characters from 33(!) to Vigor2130 Series User’s Guide...
Page 200 WPA-RADIUS The built-in RADIUS client feature enables the router to assist the remote dial-in user or a wireless station and the RADIUS server in performing mutual authentication. It enables centralized remote access authentication for network management. Vigor2130 Series User’s Guide...
Page 201 WPS (Wi-Fi Protected Setup) provides easy procedure to make network connection between wireless station and wireless access point (vigor router) with the encryption of WPA and WPA2. Vigor2130 Series User’s Guide...
Page 202 Start PBC button or using PIN Code. On the side of Vigor2130 series which served as an AP, press WPS button once on the front panel of the router or click Start PBC on web configuration interface. On the side...
Page 203 Start PBC button of network card. If you want to use PIN code, you have to know the PIN code specified in wireless client. Then provide the PIN code of the wireless client you wish to connect to the vigor router. Vigor2130 Series User’s Guide...
Page 204: Access Control
Add a new MAC address into the list. Add a New Entry Delete the selected MAC address in the list. This button Delete will appear only an entry of MAC Address has been typed. Click OK to save the configuration. Vigor2130 Series User’s Guide...
Page 205: Station List
Display the SSID of the connected station. SSID Display the authentication of the connected station. Auth Display the encryption type adapted by the connected Encrypt station. Display the connection mode used by the connected station. Mode Vigor2130 Series User’s Guide...
Page 206: Access Point Discovery
Add to type in the AP’s MAC address on the bottom of the page and click Bridge or Repeater. Next, click Add to. Later, the MAC address of the AP will be added on WDS settings page. Vigor2130 Series User’s Guide...
Page 207: Wmm Configuration
1 to 15. Be aware that CWMax value must be greater than CWMin or equals to CWMin value. Both values will influence the time delay for WMM accessing categories. The difference between AC_VI and AC_VO categories must Vigor2130 Series User’s Guide...
Page 208 WMM packets. “Check” the box means the AP router will not answer any response request for the transmitting packets. It will have better performance with lower reliability. Click OK to save the settings. Vigor2130 Series User’s Guide...
Page 209: Wds
To meet the above requirement, two WDS modes are implemented in Vigor router. One is Bridge, the other is Repeater. Below shows the function of WDS-bridge interface: The application for the WDS-Repeater mode is depicted as below: Vigor2130 Series User’s Guide...
Page 210 Please disable the unused link to get better performance. Key- Type 8 ~ 63 ASCII characters or 64 hexadecimal digits leading by “0x”. Peer Mac Address- Four peer MAC addresses are allowed Vigor2130 Series User’s Guide...
Page 211: Usb Application
This page can display current using status of the USB storage disk. If you want to remove the disk from USB port in router, please check the box of Safely Remove Disk first. And then, remove the USB storage disk later. Available settings are explained as follows: Vigor2130 Series User’s Guide...
Page 212: Format Disk (Ext2/3)
Under Linux environment, USB disk can be formatted in ext2 or ext3 to have good stability and efficiency for data transmitting. After clicking OK, the following confirmation dialog will appear. Simply click OK to continue the procedure. Vigor2130 Series User’s Guide...
Page 213: File Explorer
Click this icon to add a new folder. Create Current Path Display current folder. Upload Click this button to upload the selected file to the USB diskette. The uploaded file in the USB diskette can be shared for other user through FTP. Vigor2130 Series User’s Guide...
Page 214: Ftp User Management
It displays the access right for the connected USB disk. Access Rights Click the name link under User Name to open the setting web page. Available settings are explained as follows: Item Description Select the proper volume for the connected USB disk. Volume Vigor2130 Series User’s Guide...
Page 215: Disk Shares
LAN. It displays the name to be known by other computers in local Share Name network. It displays the description for the disk sharing. Comment It displays the directory name for the connected USB disk. Path Vigor2130 Series User’s Guide...
Page 216 Check this box to make this USB diskette to be seen in Visible Network Neighborhood on Windows of clients in local network. Specify the access right and apply to all the wireless clients Access that want to connect to the attached USB disk. Vigor2130 Series User’s Guide...
Page 217: Bit Torrent Download
USB storage device directly. Click USB Application >>Bit Torrent Download. Click Install to install the BT module for the router and the USB storage device. When the module installation is finished, you will see the following screen: Vigor2130 Series User’s Guide...
Page 218 Authentication Enable wireless clients or PC in LAN must type the username and password for authentication to the remote control services. Disable – Click it to disable authentication function. Type a name for authentication. User Name Vigor2130 Series User’s Guide...
Page 219: Itunes Server
USB storage device on Vigor router directly. Click Install to install the iTunes Server for the router and the USB storage device. When the server installation is finished, you will see the following screen: Vigor2130 Series User’s Guide...
Page 220: Dlna Server
Clients with equipments supporting DLNA can play the files stored in the USB storage device connected to Vigor2130 through the network. Click Install to install the DLNA Server for the router and the USB storage device. When the server installation is finished, you will see the following screen: Vigor2130 Series User’s Guide...
Page 221: Temperature Sensor
A USB Thermometer can be attached to Vigor router to monitor the environmental temperature. If the temperature is higher the upper limit or lower than the lower limit, an alert would be sent out for notification. Vigor2130 Series User’s Guide...
Page 222 Use the drop down list to choose a SMS profile for sending SMS Profile the alarm. Save the settings. Cancel the settings. Cancel Below shows an example of temperature graph: Current temperature, maximum temperature, minimum temperature and average temperature will be displayed on the screen. Vigor2130 Series User’s Guide...
Page 223: Voip
Then, both parties’ SIP proxies will forward the sequence of messages to caller to establish the session. If you both register to the same SIP Registrar, then it will be illustrated as below: Vigor2130 Series User’s Guide...
Page 224: Dialplan
“speed-dial” Phone Number. There are total 60 index entries in the phonebook for you to store all your friends and family members’ SIP addresses. Loop through and Backup Phone Number will be displayed if you are using Vigor2820V for setting the phone book. Vigor2130 Series User’s Guide...
Page 225 Choose one of the SIP accounts for this profile to dial out. It Dial Out Account is useful for both sides (caller and callee) that registered to different SIP Registrar servers. If caller and callee do not use Vigor2130 Series User’s Guide...
Page 226 VoIP interface. Take the above picture (Prefix Table Setup web page) as an example, the prefix number of 03 will be replaced by 8863. For example: dial number of “031111111” will be changed to “88631111111” and sent to Vigor2130 Series User’s Guide...
Page 227 This item will be changed according to the port settings configured in VoIP>> Phone Settings. After finished the above configuration, click OK to save the settings and exit this page. Vigor2130 Series User’s Guide...
Page 228 Determine the direction for the phone call, IN – incoming Call Direction call, OUT-outgoing call, IN & OUT – both incoming and outgoing calls. Determine the type of the VoIP phone call, URI/URL or Barring Type number. Vigor2130 Series User’s Guide...
Page 229 SIP accounts. Such control also can be done based on preconfigured schedules. For Block IP Address – this function can block incoming calls (through Phone port) coming from IP address. Such control also can be done based on preconfigured schedules. Vigor2130 Series User’s Guide...
Page 230 Dial the number typed in this field to release the DND Do Not Distrub [Deact] function. Dial the number typed in this field to make your phone Hide caller ID [Act] number (ID) not displayed on the display panel of remote Vigor2130 Series User’s Guide...
Page 231: Sip Accounts
Display the domain name or IP address of the SIP registrar Domain/Realm server. Display the domain name or IP address of the SIP proxy Proxy server. Display the account name of SIP address before @.. Account Name Vigor2130 Series User’s Guide...
Page 232 Some SIP server allows user to use VoIP function without registering. For such server, please check the box of Call without Registration. Choosing Auto is recommended. The system will select a proper way for your VoIP call. Vigor2130 Series User’s Guide...
Page 233 Set Phone 1 and/or Phone 2 as the default ring port(s) for this Ring Port SIP account. Choose a ring tone type for the VoIP phone call. Ring Pattern After finished the above configuration, click OK to save the settings and exit this page. Vigor2130 Series User’s Guide...
Page 234: Phone Settings
Advanced setting allows you to adjust tone settings manually if you choose User Defined. TOn1, TOff1, TOn2 and TOff2 mean the cadence of the tone pattern. TOn1 and TOn2 represent sound-on; TOff1 and TOff2 represent the sound-off. Vigor2130 Series User’s Guide...
Page 235 Dynamic RTP Port End - Specifies the end port for RTP stream. The default value is 15000. RTP TOS – It decides the level of VoIP package. Use the drop down list to choose any one of them. Vigor2130 Series User’s Guide...
Page 236 CLIR (hide caller ID)- Check this box to hide the caller ID on the display panel of the phone set. Call Waiting- Check this box to invoke this function. A Vigor2130 Series User’s Guide...
Page 237 Play dial tone only when account registered - Check this box to invoke the function. After finished the above configuration, click OK to save the settings and exit this page. Vigor2130 Series User’s Guide...
Page 238 DTMF tone as audio directly when you press the keypad on the phone OutBand - Choose this one then the Vigor will capture the keypad number you pressed and transform it to digital form then send to the other side; the receiver will generate the Vigor2130 Series User’s Guide...
Page 239: Status
WAIT_ANS - Indicates that a connection is launched and waiting for remote user’s answer. ALERTING - Indicates that a call is coming. ACTIVE-Indicates that the VoIP connection is launched. Indicates the voice codec employed by present channel. Codec Vigor2130 Series User’s Guide...
Page 240: Ipv6
The volume of present call. Speaker Gain Display logs of VoIP calls. This page defines the IPv6 connection types for WAN interface. Possible types contain Link-Local only, Static IPv6, DHCPv6 and TSPC. Each type requires different parameter settings. Vigor2130 Series User’s Guide...
Page 241 The least significant 64 bits are usually chosen as the IPv6 Address interface hardware address constructed in modified EUI-64 format. Display the fixed value (64) for prefix length. Prefix Length This type allows you to setup static IPv6 address for WAN. Vigor2130 Series User’s Guide...
Page 242 Type primary DNS Server address here. Primary DNS Server Type secondary DNS Server address here Secondary DNS Server DHCPv6 client mode would use IA_PA option of DHCPv6 protocol to obtain IPv6 prefix from server. Available settings are explained as follows: Vigor2130 Series User’s Guide...
Page 243 Type the password again to make the confirmation. Confirm Password Type the address for the tunnel broker IP, FQDN or an Tunnel Broker optional port number. IPv6-in-IPv4 Tunnel- Let the broker chose the tunnel Tunnel Mode mode appropriate for the client. Vigor2130 Series User’s Guide...
Page 244 This page defines the AICCU connection types for LAN interface. Available settings are explained as follows: Item Description Type the name obtained from the service provider. It is User Name suggested for you to apply another username and password Vigor2130 Series User’s Guide...
Page 245: Ipv6 Lan Setup
This page defines the IPv6 connection types for LAN interface. Possible types contain DHCPv6 Server and RADVD. Each type requires different parameter settings. Available settings are explained as follows: Item Description IPv6 Address - Type static IPv6 address for LAN. LAN IPv6 Configuration Vigor2130 Series User’s Guide...
Page 246: Ipv6 Firewall Setup
Display the destination IP address of such rule. Destination IP Display the source port number of such rule. Source Port Display the destination port number of such rule Destination Port Display the status (accept or drop) of such rule. Action Vigor2130 Series User’s Guide...
Page 247 Type the subnet mask here if you choose Subnet as Source Source Subnet / Choose IP Type. Or click Choose Subnet to select an Ipv6 subnet. Subnet Determine the IP type as the destination. Destination IP Type Vigor2130 Series User’s Guide...
Page 248 A message will appear from the web page: Welcome to the IPv6 Information Page! You are using IPv6 from 2001:5c0:1503:7400:30e4:139d:53c8:3a1e Set firewall rule to block all TCP traffic from this IP address. Open IPv6 >> IPv6 Firewall Setup and press Add New Rule. Vigor2130 Series User’s Guide...
Page 249 In the following dialog, please configure the page with the following values. Connect PC to http://www.ipv6.org/ with IPv6 IP address again. A message will appear from web page: Welcome to the IPv6 Information Page! You are using IPv4 from 114.37.132.219 Vigor2130 Series User’s Guide...
Page 250: Ipv6 Routing
Display the number of network segments on which the Hoplimit packet is allowed to travel before discarded. Check this box to enable an automatic refresh of the page at Auto-refresh regular intervals. Click it to reload the page. Refresh Vigor2130 Series User’s Guide...
Page 251: Ipv6 Neighbour
- neighbor may be unreachable and probes are sent to verify the reachability. Check this box to enable an automatic refresh of the page at Auto-refresh regular intervals. Click it to reload the page. Refresh Vigor2130 Series User’s Guide...
Page 252: Ipv6 Tspc Status
When the router detects all the information, the screen will be shown as follows. One set of TSPC prefix and prefix length will be obtained after the connection between TSPC and Tunnel broker built. Vigor2130 Series User’s Guide...
Page 253 When the router connects to the tunnel broker, the router will use RADVD to transmit the prefix to the PC on LAN. Next, the PC will generate one set of IPv6 public IP (see the figure below). Users can use such IP for connecting to IPv6 network. Vigor2130 Series User’s Guide...
Page 254 When your PC obtains the IPv6 address, please connect to http://www.ipv6.org. If your PC access Internet via IPv6 connection, your IPv6 address will be shown on the web page immediately. Refer to the following figure. Vigor2130 Series User’s Guide...
Page 255: Ipv6 Management
-Enable the checkbox to allow system administrators to login the Internet from the Internet. There are several servers provided by the system to allow you managing the router from Internet. Check the box(es) to specify the service. Vigor2130 Series User’s Guide...
Page 256: User
Type full name for this user. Full Name Type the password for this user. Password Type the password again for confirmation. Confirm Password Check this box to have the remote user share the disk Allow Disk Sharing information. Vigor2130 Series User’s Guide...
Page 257 Check this box to let the remote user to adjust the settings of Allow Web Portal Login router by web. When you finish the settings, simply click OK to save the configuration. The new user will be created and displayed on the page. Vigor2130 Series User’s Guide...
Page 258 To edit a user, click the name link under Username to open the following page. Modify the settings except Username and then click OK to save and exit it. If you want to remove such user settings, simply click Delete User. Vigor2130 Series User’s Guide...
Page 259: System Maintenance
Each item is explained as follows: Item Description Display the model name of the router. Model Display the firmware version of the router. Firmware Version Display the date and time of the current firmware built. Build Date/Time Vigor2130 Series User’s Guide...
Page 260 IPv6 Address - Display the IPv6 address of the WAN interface. Default Gateway - Display the gateway address of the WAN interface. Primary DNS - Display the specified primary DNS setting. Secondary DNS - Display the specified secondary DNS setting. Vigor2130 Series User’s Guide...
Page 261: 253
VigorACS user’s manual for detailed information. URL - Type the URL for VigorACS server. If the connected CPE needs to be authenticated, please set URL as the following and type username and password for VigorACS server: http://{IP address of VigorACS}:8080/ACSServer/services/ACSServlet Vigor2130 Series User’s Guide...
Page 262: System Password
This page allows you to set new password for admin operation. Available settings are explained as follows Item Description Type in the old password. The factory default setting for Old Password Vigor2130 Series User’s Guide...
Page 263: User Password
Below shows an example for accessing into User Operation with User Password. 1. Type a new password in the field of New Password and click OK. 2. The following screen will appear. Simply click OK. Vigor2130 Series User’s Guide...
Page 264 3. Log out Vigor2130 Web Configurator. 4. The following window will be open to ask for username and password. Type the new user password in the filed of Password and click Login. Vigor2130 Series User’s Guide...
Page 265: Configuration Backup
Type a key arbitrarily for encrypting the file. Keep the key in mind. You will need it whenever you want to restore such file. Click Backup button to get into the following dialog. Click Save button to open another dialog for saving configuration as a file. Vigor2130 Series User’s Guide...
Page 266 Linux platform will appear different windows, but the backup function is still available. Note: Backup for Certification must be done independently. The Configuration Backup does not include information of Certificate. Go to System Maintenance >> Configuration Backup. The following windows will be popped-up, as shown below. Vigor2130 Series User’s Guide...
Page 267: Syslog/Mail Alert
Router Name - Assign a name of this device. Server IP Address - The IP address of the Syslog server. Destination Port - Assign a port for the Syslog protocol. Log Level - Choose the severity level for the system log entry. Vigor2130 Series User’s Guide...
Page 268 Just set your monitor PC’s IP address in the field of Server IP Address. Install the Router Tools in the Utility within provided CD. After installation, click on the Router Tools>>Syslog from program menu. From the Syslog screen, select the router you want to monitor. Vigor2130 Series User’s Guide...
Page 269 Vigor2130 Series User’s Guide...
Page 270: Time And Date
Add NTP server - Click the button to add a new NTP server. Delete - Click this button to remove an NTP server. Click OK to save these settings. Vigor2130 Series User’s Guide...
Page 271: Management
A maximum of three IPs/subnet masks is allowed. IP - Indicate an IP address allowed to login to the router. Subnet Mask - Represent a subnet mask allowed to login to the router. Vigor2130 Series User’s Guide...
Page 272: Reboot System
Note that this example is running over Windows OS (Operating System). Download the newest firmware from DrayTek's web site or FTP site. The DrayTek web site is www.draytek.com (or local DrayTek's web site) and FTP site is ftp.draytek.com.
Page 273: Diagnostics
Type in the payload size of the ICMP packet. Values range Ping Size from 8 bytes to 1400 bytes. Click this button to start the ping work. The result will be Start displayed on the screen. Vigor2130 Series User’s Guide...
Page 274: Trace Route
Display the gateway address or “*” if none set. Gateway the netmask for the destination net; Display Genmask '255.255.255.255' is for a host destination and '0.0.0.0' is for the default route. Different codes represent different routing status. Flags Vigor2130 Series User’s Guide...
Page 275: Arp Cache Table
Resolution Protocol) cache held in the router. The table shows a mapping between an Ethernet hardware address (MAC Address) and an IP address. Available settings are explained as follows: Item Description Click it to clear the whole table. Clear Click it to reload the page. Refresh Vigor2130 Series User’s Guide...
Page 276: System Log
Display the type or subsystem of the system log entry. Type You can specify the type from the drop down list to display the log just for the selected type. Display a short description of the system log entry. Message Vigor2130 Series User’s Guide...
Page 277: Traffic Overview
Display the number of received frames filtered by the Filtered forwarding process. Check it to enable auto-refresh function. Auto-refresh Click it to reload the page. Refresh Click it to clear the counters for all ports. Clear Vigor2130 Series User’s Guide...
Page 278: Detailed Statistics
Rx Broadcast - Display the counting number of the received broadcast packet. Rx Pause - Display the counting number of the received pause packet. RX 64 Bytes - Display the number of 64-byte frames in Receive Size Counters Vigor2130 Series User’s Guide...
Page 279 Tx Broadcast - Display the counting number of the transmitted broadcast packet. Tx Pause - Show the counting number of the transmitted pause packet. Tx 64 Bytes - Display the number of 64-byte frames in Transmit Size Counters Vigor2130 Series User’s Guide...
Page 280: Mac Address Table
The button >> will use the last entry of the currently displayed VLAN/MAC address pairs as a basis for the next lookup. When the end is reached the text "no more entries" is shown in the displayed table, use the l<< button to start over. Vigor2130 Series User’s Guide...
Page 281: Dhcp Table
The facility provides information on IP address assignments. This information is helpful in diagnosing network problems, such as IP address conflicts, etc. Click Diagnostics and click DHCP Table to open the web page. Each item is explained as follows: Item Description Check it to enable auto-refresh function. Auto-refresh Vigor2130 Series User’s Guide...
Page 282: Data Flow Monitor
Allow to choose the page to be displayed on this screen. Page Check it to enable auto-refresh function. Auto-refresh Click it to reload the page. Refresh Display the number of the data flow. Index Display the IP address of the monitored device. IP Address Vigor2130 Series User’s Guide...
Page 283: Traffic Graph
The remaining time will be shown on the session column. Click Diagnostics and click Traffic Graph to pen the web page. Choose WAN Bandwidth, Sessions, daily or weekly for viewing different traffic graph. Click Refresh to renew the graph at any time. Vigor2130 Series User’s Guide...
Page 284: Sessions Table
Source IP: Port / source and destination IP address (es) with the port number. Dest IP: Port Display the sessions based on the state chosen here. State Click this button to search the information based on the Search Vigor2130 Series User’s Guide...
Page 285: Ports State
Item Description Check it to enable auto-refresh function. Auto-refresh Click it to reload the page if you change the LAN port Refresh connection. Or you can check Auto-refresh to reload the page by the system automatically. Vigor2130 Series User’s Guide...
Page 286 This page is left blank. Vigor2130 Series User’s Guide...
Page 287: Trouble Shooting
Turn on the router. Make sure the ACT LED blink once per second and the correspondent LAN LED is bright. If not, it means that there is something wrong with the hardware status. Simply back to “1.3 Hardware Installation” to execute the hardware installation again. And then, try again. Vigor2130 Series User’s Guide...
Page 288 Go to Control Panel and then double-click on Network Connections. Right-click on Local Area Connection and click on Properties. Select Internet Protocol (TCP/IP) and then click Properties. Vigor2130 Series User’s Guide...
Page 289 Select Obtain an IP address automatically and Obtain DNS server address automatically. Double click on the current used Mac OS on the desktop. Open the Application folder and get into Network. On the Network screen, select Using DHCP from the drop down list of Configure IPv4. Vigor2130 Series User’s Guide...
Page 290: Pinging The Router From Your Computer
Open the Application folder and get into Utilities. Double click Terminal. The Terminal window will appear. Type ping 192.168.1.1 and press [Enter]. If the link is OK, the line of “64 bytes from 192.168.1.1: icmp_seq=0 ttl=255 time=xxxx ms” will appear. Vigor2130 Series User’s Guide...
Page 291: Checking If The Isp Settings Are Ok Or Not
Open WAN>>Internet Access page and then check whether the ISP settings are set correctly. Use the Connection Type drop down list to choose Static IP/DHCP/PPPoE/PPTP/L2TP/3G USB Modem for reviewing the settings that you configured previously. Vigor2130 Series User’s Guide...
Page 292: Forcing Vigor Router Into Tftp Mode For Performing The Firmware Upgrade
The .all firmware format will remain the former configurations after upgrading firmware. 10. Input the Password if you have set one, then click Send. 11. There is a bar showing the upgrading process. Vigor2130 Series User’s Guide...
Page 293 12. When the firmware upgrade is successful, the following window will pop up. Vigor2130 Series User’s Guide...
Page 294 Transfer Abort ! appears, please check if the firmware you download is correct for your Vigor router. Note: Please turn off the Firewall protection while upgrading the firmware with Windows Vista. The Firewall function can be turned off via Control Panel >> Security Center >> Firewall. Vigor2130 Series User’s Guide...
Page 295: Backing To Factory Default Setting If Necessary
5 seconds. When you see the ACT LED blinks rapidly, please release the button. Then, the router will restart with the default configuration. After restore the factory default setting, you can configure the settings for the router again to fit your personal request. Vigor2130 Series User’s Guide...
Page 296: Contacting Your Dealer
If the router still cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@draytek.com. Vigor2130 Series User’s Guide...

This manual is also suitable for:

Vigor2130n Vigor2130vn

Draytek Vigor2130 series User Manual

Quick Links

Related Manuals for Draytek Vigor2130 series

Summary of Contents for Draytek Vigor2130 series

This manual is also suitable for:

Table of Contents