Fishfinder Waypoints; Fishfinder Alarms - Raymarine a65 Installation And Operation Instructions Manual

15.18 Fishfinder waypoints

Placing a waypoint on the fishfinder display enables you to mark a
position so that you can return to it later.
When a waypoint is placed, its details are added to the waypoint
list and a vertical line labelled WPT is displayed on-screen. The
waypoints can then be navigated to using the chart application.
Placing a Waypoint in the fishfinder
application
From the fishfinder application:
1. Select and hold the required location.
The fishfinder context menu is displayed.
2. Select Place Waypoint.
Placing a waypoint using the WPT button or
icon
From the fishfinder application:
1. Select WPT.
The waypoint menu is displayed.
2. Whilst the waypoint menu is open:
• Select WPT again to place a waypoint at your vessels position,
or
• Select the appropriate option: Place Waypoint At Vessel,
Place Waypoint At Cursor or Place Waypoint At Lat/lon.
Placing a Waypoint using the context menu
You can place a waypoint in the fishfinder application using the
context menu.
1. Open the fishfinder context menu.
2. Select Place Waypoint.
The Waypoint is placed at the cursors location and a confirmation
pop-up is displayed.
3. Select Ok to confirm waypoint placement, or
4. Select Edit to edit the new waypoints details.
188

15.19 Fishfinder alarms

The display can be configured to provide a number of fishfinder
alarms.
The following fishfinder alarms can be set when a sonar module is
detected, or when the simulator is on:
• Fish — alarm sounds when a target meets the specified sensitivity
level and, is within the depth limits (if enabled). The greater the
fish alarm sensitivity, the greater the number of target image
depths displayed.
• Fishfinder Deep — alarm sounds when the sonar module detects
that the depth is greater than the deep limit.
• Fishfinder Shallow — alarm sounds when the sonar module
detects that the depth is less than the shallow limit.
Setting up fish alarms
From the Alarms menu homescreen > Set-up > Alarms:
1. Select Fish.
The Fish alarms menu is displayed.
2. Select Fish so that On is highlighted.
3. Select Fish Sensitivity.
The fish sensitivity numeric adjust control is displayed.
4. Adjust the fish sensitivity to the require value.
The greater the fish alarm sensitivity, the greater the number of
target image depths displayed.
5. Select Fish Depth Limits so that On is highlighted.
The shallow and deep fish limit settings will be activated in the
menu.
6. Select Shallow Fish Limit.
The shallow fish limit numeric adjust control is displayed.
7. Adjust the value to the require setting.
8. Select Ok to confirm the new value and close the numeric adjust
control.
9. Select Deep Fish Limit.
The deep fish limit numeric adjust control is displayed.
10. Adjust the value to the require setting.
11. Select Ok to confirm the new value and close the numeric adjust
control.
Setting up fishfinder deep alarm
From the Alarms menu homescreen > Set-up > Alarms:
1. Select Fishfinder Deep.
2. Select Deep so that On is highlighted.
Selecting Deep will switch between On and Off.
3. Select Deep Limit.
The deep limit numeric adjust control is displayed.
4. Adjust the setting to the required value.
5. Select Ok to confirm the new value and close the numeric adjust
control.
Note: The Deep Limit cannot be set to less than the Shallow
Limit.
Setting up fishfinder shallow alarm
From the Alarms menu homescreen > Set-up > Alarms:
1. Select Fishfinder Shallow.
2. Select Shallow so that On is highlighted.
Selecting Shallow will switch between On and Off.
3. Select Shallow Limit.
The shallow limit numeric adjust control is displayed.
4. Adjust the setting to the required value.
5. Select Ok to confirm the new value and close the numeric adjust
control.
Note: The Shallow Limit cannot be set to greater than the Deep
Limit.
New a Series / New c Series / New e Series