Page 1 N e w a S e r ie s N e w c S e r ie s N e w e S e r ie s Ins ta lla tion a nd ope ra tion ins tructions Da te : 10-2012 Docume nt numbe r: 81337-5-EN ©...
Page 3 Product handbooks The latest versions of all English and translated handbooks are available to download in PDF format from the website www.raymarine.com. Please check the website to ensure you have the latest handbooks.
Page 5: Table Of Contents
Contents Chapter 1 Important information....... 9 4.8 Fastheading connection..........50 4.9 SeaTalk connections..........50 TFT Displays ..............9 4.10 SeaTalk connection ..........52 Water ingress ..............10 4.11 NMEA 0183 connection ........... 52 Disclaimers ..............10 4.12 NMEA 2000 connection ........... 53 Chart cards and memory cards........
Page 6 Chapter 15 Using the fishfinder ......171 capacity ............... 118 15.1 How the fishfinder works........172 Chapter 12 Using the chart........119 15.2 Raymarine sonar modules ........172 12.1 Chart application overview ........120 15.3 Traditional sonar technology ........173 12.2 Chart ranging and panning........121 15.4 Broadband CHIRP sonar technology ......
Page 7 Media player controls........240 30.6 Power cables ............296 22.6 Media player controls using a remote 30.7 a65 / a67 spares ........... 297 control ................. 240 30.8 e7 e7D spares ............297 22.7 Unpairing a Bluetooth device ......... 241 30.9 e95 / e97 / c95 / c97 spares ........298 30.10 e125 / e127 / c125 / c127 spares......
Page 8 New a Series / New c Series / New e Series...
Page 9: Chapter 1 Important Information
Warning: FCC Warning (Part 15.21) securely closed Changes or modifications to this equipment not expressly approved in writing by Raymarine To prevent water ingress and consequent damage to Incorporated could violate compliance with FCC rules the display, ensure that the chart card door is firmly and void the user’s authority to operate the equipment.
Page 10: Water Ingress
RF exposure memory card (as applicable). Raymarine does not warrant that this product is error-free or that it This transmitter with its antenna is designed to comply with FCC / IC is compatible with products manufactured by any person or entity RF exposure limits for general population / uncontrolled exposure.
Page 11: Industry Canada (Français)
Directive requires the recycling of waste electrical and electronic equipment. Whilst the WEEE Directive does not apply to some Raymarine products, we support its policy and ask you to be aware of how to dispose of this product. Important information...
Page 12 New a Series / New c Series / New e Series...
Page 13: Chapter 2 Handbook Information
Chapter 2: Handbook information Chapter contents • 2.1 Handbook information on page 14 • 2.2 Product information on page 15 • 2.3 Handbook illustrations on page 16 • 2.4 Handbook conventions on page 17 • 2.5 Touch and non-touch operations on page 19 Handbook information...
Page 14: Handbook Information
Part number This handbook contains important information regarding your multifunction display. SeaTalk reference manual 81300 The handbook is for use with the following Raymarine multifunction displays: • New a Series • New c Series • New e Series About this handbook...
Page 15: Product Information
2.2 Product information The following Raymarine multifunction display variants are available Non- sonar Sonar variant variant Series Controls Features New a Series • Bluetooth. (E70076) (E70077) • Internal GPS. Touchscreen only New e Series • Bluetooth. (E62354) (E62355) • Wi-Fi...
Page 16: Handbook Illustrations
2.3 Handbook illustrations The illustrations and screenshots used in this handbook may differ slightly from your display model. The illustration of the multifunction display below is used throughout this manual and unless otherwise stated can apply to all variants of multifunction display (i.e. New a series, New c Series and New e Series).
Page 17: Handbook Conventions
2.4 Handbook conventions The following conventions are used throughout this handbook when referring to: Type Example Convention Icons The term "select" is used in procedures involving icons to refer to the action of selecting an on-screen icon, either using touch or physical buttons: •...
Page 18 Waypoint (MOB) button / icon Depending on the multifunction display variant there will be either a Waypoint (MOB) button or an on-screen icon. WPT button • New c Series • New e Series WPT icons • New a Series Throughout this manual the term: Select WPT, refers to pressing the physical WPT button or pressing the on-screen WPT icon.
Page 19: Touch And Non-Touch Operations
2.5 Touch and non-touch operations This handbook applies to New a Series, New c Series and New e Series multifunction displays. All features and functions can be accessed using physical buttons (non-touch) on New c Series and New e Series displays or by using the touchscreen on New a Series and New e Series displays.
Page 20 New a Series / New c Series / New e Series...
Page 21: Chapter 3 Planning The Installation
Chapter 3: Planning the installation Chapter contents • 3.1 System integration on page 22 • 3.2 Installation checklist on page 26 • 3.3 System Limits on page 26 • 3.4 Multiple data sources (MDS) overview on page 27 • 3.5 Identifying your display variant on page 27 •...
Page 22: System Integration
1 per multifunction display. Raymarine RCU-3 Bluetooth Smartphone / Tablet device 1 per multifunction display. For Raymarine wireless video streaming and • Chartplotter sync with Navionics Marine remote control apps: app: Wi-Fi. • Video streaming and remote control: • Apple iPhone 4 (or later) or iPad 2 (or Wi-Fi.
Page 23 = 2 IP camera Only 1 camera may be Third party IP camera Via SeaTalk network. viewed at a time. Lifetag (Man overboard alert) 1 basestation All Raymarine Lifetag basestations. SeaTalk (via optional SeaTalk to SeaTalk converter) Planning the installation...
Page 24 New e Series (excluding e7 External display. 15 pin D-Type connector (VGA Style). and e7D) = 1 Sonar transducer Direct connection to display (Sonar variant Raymarine transducer connection, OR Minn displays only): Kota transducer connection. • Raymarine P48. • Raymarine P58. • Raymarine P74.
Page 25 • CP450C SeaTalk Raymarine • DSM30. • DSM300. Radar — Raymarine All Raymarine Non-HD Digital Radomes and SeaTalk HD or SuperHD radar scanners. Note: Please ensure your radar scanner is using the latest software version. Thermal camera — All Raymarine thermal cameras.
Page 26: Installation Checklist
3.2 Installation checklist 3.3 System Limits Installation includes the following activities: The following limits apply to the number of system components that can be connected in a Raymarine multifunction display system. Installation Task Component Maximum Plan your system. Maximum number of SeaTalk Obtain all required equipment and tools.
Page 27: Multiple Data Sources (Mds) Overview
NOT compliant. It may be necessary to upgrade the software for these non-compliant products to make them compliant. Visit the Raymarine website (www.raymarine.com) to obtain the latest software for your products. If MDS-compliant software is not available and you do NOT want the system to automatically attempt to resolve data conflicts, any non-compliant product(s) can be removed or replaced to ensure the entire system is MDS-compliant.
Page 28: Networking Constraints
New a Series, New c Series and New e Series displays can be Sonar operation networked together and can also be networked to Raymarine’s E-Series Widescreen displays and G-Series systems. Caution is • You can connect an external sonar module unit to New a Series,...
Page 29: Typical Systems
SeaTalk / RayNet SeaT alk / RayNet SeaT alk D12245-2 1. Raymarine Multifunction display. 2. Raymarine network switch. 3. Raymarine radar scanner. 4. SPX course computer. 5. SeaTalk Pilot controller. Note: A network switch is only required if multiple devices are connected using SeaTalk / RayNet.
Page 30 Example: Basic system with sonar variant display SMART SeaT alk / RayNet SeaT alk D12589-1 1. Multifunction display 2. Sonar transducer. 3. Radar scanner. 4. SPX course computer. 5. SeaTalk pilot controller. Example: Basic system with non-sonar variant display SMART SeaT alk / RayNet SeaT alk...
Page 31 Example: Expanded system SeaT alk DeviceNet SeaT alk / RayNet SeaT alk / RayNet SeaT alk / RayNet SeaT alk / RayNet D12247-2 1. Radar scanner. 2. Weather sensor. 3. Sirius weather receiver. 4. Sonar module. 5. SeaTalk Pilot controller. 6.
Page 32: System Protocols
3.8 System protocols information is passed in ‘sentences’, each of which has a three letter sentence identifier. It is therefore important when checking compatibility between items that the same sentence identifiers are Your Multifunction Display can connect to various instruments and used some examples of which are: displays to share information and so improve the functionality of the system.
Page 33: Data Master
3.9 Data master 3.10 New a Series parts supplied Any system containing more than one networked multifunction The following items are supplied with your a65 / a67 multifunction display must have a designated data master. display. The data master is the display which serves as a primary source of data for all displays, it also handles all external sources of information.
Page 34: E7 / E7D Parts Supplied
3.11 e7 / e7D Parts supplied 3.12 New c Series and New e Series parts supplied The parts shown below are supplied with the e7 / e7D multifunction display. The parts shown below are supplied with the New c Series and New e Series (Excluding e7 and e7D) multifunction displays.
Page 35: Tools Required For Installation
3.13 Tools required for installation D12171-1 1. Power drill. 2. Jigsaw. 3. Pozidrive screwdriver. 4. Adhesive tape. 5. Drill bit for trunnion bracket mounting. 6. File. 7. Hole saw for flush mounting (For hole saw size refer to your product’s mounting template). 8.
Page 36 New a Series / New c Series / New e Series...
Page 37: Chapter 4 Cables And Connections
Chapter 4: Cables and connections Chapter contents • 4.1 General cabling guidance on page 38 • 4.2 Connections overview on page 39 • 4.3 Power connection — New a Series on page 40 • 4.4 Power connection — New c Series and New e Series on page 41 •...
Page 38: General Cabling Guidance
• Unless otherwise stated use only standard cables of the correct type, supplied by Raymarine. • Ensure that any non-Raymarine cables are of the correct quality and gauge. For example, longer power cable runs may require larger wire gauges to minimize voltage drop along the run.
Page 39: Connections Overview
4.2 Connections overview Details of the connections available on Raymarine multifunction displays are shown below. a 65 a 67 e 7D e 95 / e 125 / e 165 e 97 / e 127 c97 / c127 c95 / c125...
Page 40: Power Connection - New A Series
Power distribution Note: The suitable fuse rating for the thermal breaker is dependent on the number of devices you are connecting. If in Raymarine recommends that all power connections are made via a doubt consult an authorized Raymarine dealer. distribution panel.
Page 41: Power Connection - New C Series And New E Series
Power distribution Raymarine recommends that all power connections are made via a Breakers, fuses and circuit protection distribution panel. • All equipment must be powered from a breaker or switch, with The power cable includes an in-line fuse.
Page 42 Sharing a breaker Where more than 1 piece of equipment shares a breaker you must provide protection for the individual circuits. E.g. by connecting an in-line fuse for each power circuit. D11637-2 Positive (+) bar Negative (-) bar Circuit breaker Fuse Where possible, connect individual items of equipment to individual circuit breakers.
Page 43: Network Connections
• Ethernet IP cameras. Note: Your multifunction display includes the following network connectors: • e7, e7D, a65 and a67 = 1 x SeaTalk / RayNet connector. • New c Series and New e Series (excluding the e7 and e7D) = 2 x SeaTalk / RayNet connectors.
Page 44 • New a Series and the e7 / e7D displays can connect 1 SeaTalk / RayNet device directly to the display. • Patch — for connecting the following devices to a Raymarine network switch: The radar is usually connected via a Raymarine network switch. On –...
Page 45 D12254-1 1. Radar extension cable. 2. Radar power and data digital cable. 3. Raymarine network switch (or crossover coupler if connecting radar directly to display). 4. RayNet cable (or RayNet to SeaTalk cable if connecting via crossover coupler). Note: The extension cable connects to the radar scanner.
Page 46 3. Raymarine sonar module. A55078D 15 m (49.2 ft) Power and data digital 4. RayNet cable. cable The multifunction display can be used with the following Raymarine 25 m (82.0 ft) Power and data digital A55079D sonar modules: cable • CP450C Note: The maximum length for the radar power and data digital •...
Page 47 2. E66066 adaptor cable. e165 3. Sonar transducer. Transducer adaptor cable Minn Kota transducer adaptor cable Connects a Minn Kota sonar transducer to a compatible Raymarine Cable Part number multifunction display. 0.5 m (1.64 ft) transducer adaptor E66066 Cable...
Page 48 Raymarine network switch Video cables are not supplied with the product. Please contact your IP cameras dealer for suitable cables and adaptors. Raymarine recommends the use of a BNC terminated RG59 75ohm SeaTalk cross over couplers (or better) coaxial cable.
Page 49: Gps Connection
4.6 GPS connection 4.7 AIS connection Depending on display variant, your multifunction display may include A compatible AIS can be connected using SeaTalk or NMEA 0183. an internal GPS receiver. If required the multifunction display can Connection using SeaTalk also be connected to an external GPS receiver, using SeaTalk or NMEA 0183.
Page 50: Fastheading Connection
The SeaTalk bus requires a 12 V power supply. Power may be provided from: • Raymarine equipment with a regulated 12 V power supply (for example, a SmartPilot SPX course computer); or: • Other suitable 12 V power supply. Note: SeaTalk does NOT supply power to multifunction displays and other equipment with a dedicated power supply input.
Page 51: Seatalk Ng Cabling Components
SeaTalk cabling components Description Part No Notes SeaTalk cabling components and their purposes. SeaTalk to bare ends A06044 3 m (9.8 ft) spur Connection / Cable Notes SeaTalk Power cable A06049 Backbone cable (various lengths) The main cable carrying data. Spurs from the backbone are used to SeaTalk Terminator...
Page 52: Seatalk Connection
4.11 NMEA 0183 connection 4.10 SeaTalk connection NMEA 0183 devices can be connected to New c Series and New e You can connect SeaTalk devices to your multifunction display using Series multifunction displays using the power and data cable. the optional SeaTalk to SeaTalk converter.
Page 53: Nmea 2000 Connection
4.12 NMEA 2000 connection Positive (+) Ite- Cable Input / / negative The display can receive data from NMEA 2000 devices (e.g. data Device color Port output from compatible engines). The NMEA 2000 connection is made NMEA Output Positive using SeaTalk and appropriate adaptor cables.
Page 54: Camera / Video Connection
4.13 Camera / Video connection 4.14 Camera / video in-out connection A camera / video device or external display can be connected to A camera or a video device can be connected directly to New c New e Series multifunction displays (excluding the e7 / e7D) using Series and New e Series multifunction displays using the video the dedicated video in/out connector.
Page 55: Bluetooth Connections
D12163-2 1. Multifunction display. 2. Bluetooth connection. 3. Raymarine Bluetooth remote control (for example, RCU-3). To use the remote control you must first: • Enable Bluetooth in the System Settings on the multifunction display. • Pair the remote control unit with the multifunction display.
Page 56: Wifi Connections
• Enable Audio Control in the System Settings on the multifunction Raymarine apps allow you to stream and / or control, remotely what display. you see on your multifunction display to a compatible device, using •...
Page 57: Chapter 5 Location And Mounting
Chapter 5: Location and mounting Chapter contents • 5.1 Selecting a location on page 58 • 5.2 Mounting - New a Series on page 59 • 5.3 Mounting - New c Series and New e series on page 61 Location and mounting...
Page 58: Selecting A Location
5.1 Selecting a location Warning: Potential ignition source This product is NOT approved for use in ( 7 . 8 5 0 0 hazardous/flammable atmospheres. Do NOT install in . 7 i 7 i n ( 1 9 a hazardous/flammable atmosphere (such as in an 2 5 0 engine room or near fuel tanks).
Page 59: Mounting - New A Series
Viewing angle considerations As display contrast, color and night mode performance are all D12576-1 affected by the viewing angle, Raymarine recommends you temporarily power up the display when planning the installation, to a65 / a67 enable you to best judge which location gives the optimum viewing 60º...
Page 60 • Attached the front bezel. D12585-1 1. Check the selected location for the unit. A clear, flat area with suitable clearance behind the panel is required. 2. Drill or knock out the 4 mounting holes on the unit D12578-1 1. Mark the location of the mounting bracket screw holes on the chosen mounting surface.
Page 61: Mounting - New C Series And New E Series
5.3 Mounting - New c Series and New e ensuring that the clips along the bottom edge of the bezel latch into position. series Viewing angle D12268-1 e95 / e97 / e125 / e127 / e7 / e7D e165 c95 / c97 c125 / c127 70º...
Page 62: Flush Mounting
1. Remove the front bezel. Refer to the separate instructions 1. Check the selected location for the unit. A clear, flat area with provided for that procedure. suitable clearance behind the panel is required. 2. Fix the appropriate cutting template supplied with the product, to the selected location, using masking or self-adhesive tape.
Page 63 Before mounting the unit ensure that you have: ensuring that the clips along the bottom edge of the bezel latch into position. • Selected a suitable location. • Identified the cable connections and route that the cables will take. • Attach the front bezel. D12274-1 4.
Page 64 New a Series / New c Series / New e Series...
Page 65: Chapter 6 Getting Started
Chapter 6: Getting started Chapter contents • 6.1 Display power on page 66 • 6.2 New a Series Controls on page 66 • 6.3 e7 / e7D Controls on page 67 • 6.4 c95 / c97 / c125 / c127 / e95 / e97 / e125 / e127 / e165 Controls on page 67 •...
Page 66: Display Power
6.1 Display power 6.2 New a Series Controls Powering the display on 1. Press and hold the POWER button until the Raymarine logo appears. 2. Select Accept to acknowledge the disclaimer message. Powering the display on 1. Press and hold the POWER button until the Raymarine logo appears.
Page 67: E7 / E7D Controls
6.3 e7 / e7D Controls 6.4 c95 / c97 / c125 / c127 / e95 / e97 / e125 / e127 / e165 Controls D12179-1 1. Touchscreen — you can touch the screen to operate many common functions, including all menu operations (HybridTouch multifunction displays only).
Page 68 The cursor appears on the screen as a white cross. If the cursor has not been moved for a short period of time, it changes to a circle with a cross in it, to make it easier to locate on the screen. The cursor is context-sensitive.
Page 69: Hybridtouch Overview
(such as rough sea conditions) when it is not Note: Raymarine strongly recommends that you familiarize appropriate to use the touchscreen. In these situations, Raymarine yourself with touch operations while your vessel is anchored strongly recommends that you activate the touch lock and use the or moored.
Page 70: Homescreen Overview - New A Series
6.7 Homescreen overview — New a 6.8 Homescreen overview — New c Series Series / New e Series The homescreen provides a central point of access to your display's The homescreen provides a central point of access to your display's range of applications.
Page 71: System Checks
Course Over Ground (COG) data is available. be using the same datum. Note: Raymarine recommends that you check the displayed The accuracy of the GPS receiver depends on the parameters vessel position in the chart application against your actual detailed above, especially the azimuth and elevation angles which proximity to a known charted object.
Page 72: Sonar Check
• Sonar variant displays allow the direct connection of EITHER a Raymarine OR a Minn Kota sonar transducer. • All variants allow the connection of a Raymarine sonar transducer via a compatible external sonar module. • For all variants use the Transducer Set-Up menu in the fishfinder application to specify the sonar transducer you want to use.
Page 73 3. Select Transducer Set-Up. Panning and tilting, and the thermal image 4. Select Transducer. On a New e Series multifunction display you can pan and tilt the A list of transducers is displayed. thermal camera image using the touchscreen. 5. Select the transducer you want to use. Move your finger up and down the screen to tilt the camera up or down.
Page 74: Enabling Autopilot Functions
6.10 Enabling autopilot functions 6.11 Enabling AIS functions With the homescreen displayed: Before proceeding ensure your AIS unit is connected to NMEA Port 1. 1. Select Set-up. With the homescreen displayed: 2. Select System Settings. 1. Select Set-Up. 3. Select Autopilot Control so that On is highlighted. 2.
Page 75: Language Selection
6.12 Language selection 6.13 Pages The system can operate in the following languages: Pages are used to display applications. Pages are displayed and accessed on the homescreen. Each page English (US) English (UK) Arabic can display more than 1 application. Chinese Croatian Danish...
Page 76: Applications
6.14 Applications Changing an empty page With the homescreen displayed: Chart application — provides a 2D or 3D graphical 1. Select Customize. view of your charts to help you navigate. Waypoint, 2. Select Homescreen. route, and track functions enable you to navigate to a specific location, build and navigate routes, 3.
Page 77: Splitscreen Controls
6.15 Splitscreen controls Selecting the active window — e7 / e7D When viewing a page with more than 1 application displayed you When viewing a splitscreen page you can select the active can switch applications from the splitscreen view to fullscreen view. application and view it fullscreen on an e7 / e7D with the touch lock enabled by following the steps below.
Page 78: Screen Overview
6.16 Screen overview D12281-2 D12196-1 Screen item Description Screen item Description Back — On touchscreen displays (New e Series and New a series) you can press the on-screen << (back) icon to go back Home to a previous menu. (On New c Series displays use the Back •...
Page 79 Screen item Description Screen item Description Back Close — On Touchscreen displays you can select this icon to close the menu(s). The close icon is not available on • Touchscreen — Select the on-screen Back icon to go non-touchscreen displays. back to the previous menu.
Page 80: Editing Information In Dialogs
6.17 Editing information in dialogs Screen item Description Status — provides status information for the connected With the dialog displayed: equipment. For example, the Pilot Control dialog displays 1. Select the field you want to edit. the locked heading and current navigation mode for a The on-screen keyboard is displayed: connected autopilot unit.
Page 81: Editing Numerical Settings
6.18 Editing numerical settings 6.19 Basic touchscreen operations To edit numerical values in you can either use the Rotary Control, Placing and moving the cursor using touch the on-screen numeric adjust control or on-screen numeric keypad to increase or decrease the value. To place or move the cursor around the screen on a touchscreen multifunction display follow the steps below.
Page 82: Databar Status Symbols
6.20 Databar status symbols Symbol Description AIS unit is connected and switched on, but has The status symbols on the databar confirm whether the appropriate active alarms. connections to your system have been made. The symbols show the status for the following: AIS unit is connected and switched on, but the •...
Page 83: Initial Set Up Procedures
6.21 Initial set up procedures Symbol Description Power steering active. Once your display has been installed and commissioned, Raymarine recommends that you perform an initial set up procedure. Startup wizard Wind Vane mode is active. D12568-1 When you power-up the display for the first time or after a system reset a Startup Wizard is displayed.
Page 84: Data Master
5. Repeat the action a further 3 times. The simulator mode is switched on / off in the System Setup Menu. 6. If the operation was successful, an “Alignment Completed” Note: Raymarine recommends that you do NOT use the message is displayed. simulator mode whilst navigating.
Page 85 Note: Any system settings made whilst in Simulator mode are NOT transmitted to other equipment. Enabling and disabling simulator mode You can enable and disable simulator mode by following the steps below. With the homescreen displayed: 1. Select Set-Up . 2.
Page 86 New a Series / New c Series / New e Series...
Page 87: Chapter 7 Managing Display Data
Chapter 7: Managing display data Chapter contents • 7.1 Memory cards overview on page 88 • 7.2 Inserting a memory card or chart card on page 88 • 7.3 Removing a memory card or chart card on page 89 • 7.4 Saving user data and user settings on page 89 •...
Page 88: Memory Cards Overview
2. Insert the card, as shown in the diagram below. For slot 1, the card contacts should be facing DOWN. For slot 2, the card Note: Raymarine recommends that you backup your data to a contacts should be facing UP. Do NOT force the card. If the card memory card on a regular basis.
Page 89: Removing A Memory Card Or Chart Card
Note: Raymarine recommends that you save your user data and user settings to a memory card on a regular basis. Note: Raymarine strongly recommends that you save settings to a separate memory card, and NOT to a chart card containing cartography.
Page 90 4. Select SD1 for a memory card in the top card slot, or SD2 for a Application Setting memory card in the bottom card slot. 5. Select Erase Waypoints from Card, Erase Routes from Card, MOB Data type or Erase Tracks from Card, as appropriate. Variation source Erasing waypoints, routes, and tracks from the Manual variation...
Page 91 Data application Application Setting Application Setting Data overlay cell 2 on / off Data Datapages and content Data overlay cell 2 content Datapage order Chart object menu Color theme Chart display Dial color Chart grid Number of engines 2D shading Maximum tachometer range Community layer Chart text...
Page 92: Screenshots
7.6 Resetting your system 7.5 Screenshots You can take a screenshot of what is currently displayed on the Your system may be reset to its factory default settings if required. screen. There are 2 types of reset operation, both of which affect the current Screenshots are saved to an SD card in .bmp (bitmap) format.
Page 93: Chapter 8 Using The Document Viewer
Chapter 8: Using the document viewer Chapter contents • 8.1 Document viewer overview on page 94 Using the document viewer...
Page 94: Document Viewer Overview
8.1 Document viewer overview • Move your finger up to scroll down the document. • Move your finger down to scroll up the document. Your multifunction display includes a pdf document viewer. The document viewer is available from the homescreen and is used to view and search pdf documents (such as product handbooks).
Page 95 Searching for text On touchscreen displays you can use the find function to search for text in an open pdf document. With a pdf document open: 1. Select Menu. 2. Select Find. The on-screen keyboard is displayed. 3. Enter the keyword you want to find. 4.
Page 96 New a Series / New c Series / New e Series...
Page 97: Chapter 9 Using Autopilot Control
Chapter 9: Using autopilot control Chapter contents • 9.1 Autopilot control on page 98 • 9.2 Autopilot status symbols on page 99 • 9.3 Autopilot alarms on page 100 Using autopilot control...
Page 98: Autopilot Control
On multifunction displays which do not have a dedicated pilot button (i.e. a65, a67, e7 and e7D) you can engage the autopilot from the Dismiss — Dismisses the Pilot Control dialog.
Page 99: Autopilot Status Symbols
9.2 Autopilot status symbols Engaging the autopilot using the context menu From the chart application context menu:: The autopilot status is indicated in the databar. 1. Select any of the following options from the Chart context menu: Symbol Description • Goto Waypoint Autopilot is in Standby mode.
Page 100: Autopilot Alarms
9.3 Autopilot alarms The autopilot function provides alarms to alert you to situations that require action. Your multifunction display shows autopilot alarms, regardless of whether there is active navigation on the system. If autopilot control is enabled, and an alarm is raised by the autopilot, the multifunction display provides an audible alarm sound (providing that the alarm has not already been silenced).
Page 101: Chapter 10 Using Alarms And Mob Functions
Chapter 10: Using alarms and MOB functions Chapter contents • 10.1 Using Man Overboard (MOB) functions on page 102 • 10.2 Alarms on page 103 Using alarms and MOB functions...
Page 102: Using Man Overboard (Mob) Functions
• An audible MOB alarm is sounded. • An MOB alarm dialog box is displayed. • The system sends MOB alarms to other Raymarine equipment. • The active chart application is changed to a low-detail 2D view, with an initial range of 15 m (50 ft). Motion mode is set to Auto Range.
Page 103: Alarms
10.2 Alarms Alarms alert you to a situation or hazard requiring your attention. You can set up alarms to alert you to certain conditions, such as collision warnings and temperature limits. Alarms are raised by system functions, and also external equipment connected to your multifunction display.
Page 104 Alarms menu Menu item Description Options MOB Data Type Determines whether Position or Dead Reckoning (DR) data is displayed. • Dead Reckoning Assuming that your vessel and the MOB are subject to the same tide and • Position (default) wind effects, the Dead Reckoning setting normally gives a more accurate course.
Page 105 Menu item Description Options • Deep Fish Limit — Specifies the upper value for the Fish Alarm Depth Shallow Fish Limit Limit. • 2 ft (or equivalent units) to the maximum of the transducer range Deep Fish Limit • 2 ft (or equivalent units) to the maximum of the transducer range Fuel Manager In the fuel manager alarm options you can switch the low fuel warning...
Page 106 New a Series / New c Series / New e Series...
Page 107: Chapter 11 Using Waypoints, Routes And Tracks
Chapter 11: Using waypoints, routes and tracks Chapter contents • 11.1 Waypoints on page 108 • 11.2 Routes on page 113 • 11.3 Tracks on page 116 • 11.4 Waypoints, routes and tracks storage capacity on page 118 Using waypoints, routes and tracks...
Page 108: Waypoints
11.1 Waypoints Showing and hiding waypoint groups / symbols From the chart or radar application: A waypoint is a position marked on the screen to indicate a site 1. Select WPT. or a place to navigate to. 2. Select Display Wpts on: Chart, or Display Wpts on: Radar As well as acting as position markers, waypoints are also the depending on the application you have open.
Page 109 • Advance Waypoint 1. Select and hold the required location on screen. The context menu is displayed. • Measure 2. Select Place Waypoint. • Build Route • Acquire Target (only available if Radar overlay is switched on.) Placing a waypoint •...
Page 110 Navigating to a waypoint on the screen Cross Track Error (XTE) Cross Track Error (XTE) is the amount of deviation from your intended route or waypoint, expressed as a distance. D11753-2 From the chart or radar application: 1. Select the waypoint. D11765-2 The waypoint context menu is displayed.
Page 111: Moving Waypoints
Note: You can also access the waypoint list from the homescreen Symbol Type Symbol Type and chart application by going to the My Data menu and selecting Route start School of fish Waypoint List. Seaweed Shark Waypoint editing Skull Small fish Editing waypoint details With the Waypoint List displayed: Sport fisher...
Page 112 2. Select Erase Waypoint. 1. Select the group you want to rename. The erase waypoint pop up message is displayed. 2. Select Edit Group Name. 3. Select Yes to confirm, or No to cancel. The on-screen keyboard is displayed. 3. Using the on-screen keyboard, edit the group name. Note: If you erase a waypoint which is part of a route the erase 4.
Page 113: Routes
11.2 Routes From the chart application: 1. Select and hold a location on screen. A route is a series of waypoints typically used to assist with passage The chart context menu is displayed. planning and navigation. 2. Select Build Route. A route is displayed on screen as a series of waypoints linked by a The build route menu is displayed.
Page 114 Route context menu Adjusting chart range while building a route Placing the cursor over a route in the chart application displays a From the Build Route menu: context menu showing the leg of the route highlighted by the cursor and menu items. 1.
Page 115 You can also follow any route in reverse order. Following a stored route From the chart application: 1. Select Menu. 2. Select Navigate. 3. Select Follow Route. The Route list is displayed. 4. Select the route you want to follow. 5.
Page 116: Tracks
11.3 Tracks 3. Select Yes to confirm or No to cancel the action. A track is an on-screen trail that shows the passage you have taken. Moving a waypoint within a route This trail is made up of a series of track points which are created From the chart application: automatically.
Page 117: Erasing Tracks
• Auto— The track interval is automatically set (Auto will • Erase a track. minimize track points whilst maintaining correlation between • Create a route from a track. the track and the actual path followed). • Show or hide a track on the chart (only available from the chart •...
Page 118: Waypoints, Routes And Tracks Storage Capacity
11.4 Waypoints, routes and tracks storage capacity The display can store the following quantities of waypoints, routes and tracks Waypoints • 3000 Waypoints • 100 waypoint groups Routes • 150 routes, each consisting of up to 50 waypoints. Tracks • 15 tracks, each consisting of up to 10000 track points. New a Series / New c Series / New e Series...
Page 119: Chapter 12 Using The Chart
Chapter 12: Using the chart Chapter contents • 12.1 Chart application overview on page 120 • 12.2 Chart ranging and panning on page 121 • 12.3 Vessel position and orientation on page 122 • 12.4 Chart views on page 124 •...
Page 120: Chart Application Overview
, it will automatically correlate each time you change the datum on the multifunction display. • If you have a Raymarine GPS receiver using NMEA0183, or a third-party GPS receiver, you must correlate it separately. New a Series / New c Series / New e Series...
Page 121: Chart Ranging And Panning
Display Preferences • Enable Wi-Fi on your tablet / smartphone. > Range Controls • Select the Raymarine Wi-Fi connection from the list of available Wi-Fi networks on your tablet / smartphone. Panning the chart You can pan the chart area on a touchscreen multifunction display by following the steps below.
Page 122: Vessel Position And Orientation
12.3 Vessel position and orientation Head-Up Vessel position on the chart display Your current position is represented on screen by the vessel symbol. The symbol used for your vessel will vary depending on the vessel type selected during initial set up of your multifunction display. Motor Vessels Sail Vessels D12298-1...
Page 123 When the motion mode is set to True Motion, the chart is fixed and Note: In the 3D chart view, only Relative Motion mode is the vessel moves in true perspective to fixed landmasses on the available. screen. As the vessel’s position approaches the edge of the screen, the chart picture is automatically reset to reveal the area ahead The current motion mode applies to the active instance of the chart of the vessel.
Page 124: Chart Views
12.4 Chart views 3D chart view The 3D view can display a range of information to help you navigate. Switching between 2D/3D chart view You can switch between 2D and 3D views. From the chart application: 1. Select Menu. 000°T 2.
Page 125: Chart Context Menu
12.5 Chart context menu ii. New a series or New e Series — Swipe your finger up or down across the screen to adjust the pitch. Placing the cursor over an area in the chart application displays a D11755-1 context menu showing the cursors positional data and menu items. 4.
Page 126: My Data Options
12.6 My Data options 12.7 Navigation options The chart provides features to help you manage your data and help The chart application provides features to help navigate to a chosen plan your navigation to a chosen location. location. The options are found in the My Data menu: Menu > My Data. The navigation options are found in the Navigate menu: Menu >...
Page 127: Measuring Distances And Bearings
12.8 Measuring distances and bearings 12.9 Chart vectors You can use the databar and context menu information you can use Chart vectors display indicators for heading, COG, wind direction the measure function to measure distances in the chart application. and tide direction. You can determine the distance and bearing: A range of vector graphics can be displayed in the chart application when in 2D chart view.
Page 128: Current Information
12.10 Current information 7. To set the animation date to 24 hours ahead of the current date select Next Day. Animated current information Displaying details of currents The electronic charts may allow animation of the current information current stations. From the chart application: 1.
Page 129: Tide Information
12.11 Tide information Tide graphs Tide graphs provide a graphical view of tidal activity. Animated tide information The electronic charts may allow animation of the tide information tide stations. Animated tide information is available in the chart application wherever a diamond-shaped symbol with a "T" is displayed: This symbol identifies tide stations and the availability of tide information for the location.
Page 130: Chart Object Information
12.12 Chart object information 5. Select SEARCH. The search results are displayed. You can display additional information on the chart for cartographic 6. Select an entry in the list to display more information. objects, ports, and marinas. You can also search for the nearest instance of a particular chart Displaying pilot book information object and search for ports by name.
Page 131: Chart Presentation
12.13 Chart presentation • Radar — Overlay radar onto the chart (2D view only). • NOWRad — Provides the NOWRad weather radar overlay, The chart has a number of presentation options which affect the without the need to open a separate weather application window level of detail, types of objects and aspects of its operation.
Page 132 Radar overlay NOWRad weather overlay You can combine the chart with the radar and MARPA functions With a suitable weather receiver connected to your multifunction to provide target tracking or to help you distinguish between fixed display, you can overlay NOWRad weather information on the chart objects and other marine traffic.
Page 133 4. Select Range Rings so that On is highlighted. • Course remaining in a straight line. Selecting range rings will switch range rings between On and Off. • Current speed maintained. Safe Zone Ring Note: The chart application can display and configure a MARPA / AIS The fuel range ring is an estimated range that can be reached safe zone ring.
Page 134 4. Select 3D Display Options. 5. Select Transducer Cone so that On is highlighted. Selecting Transducer cone will switch the function on and off. Enabling depth scale To enable a depth indicator at your vessels location follow the steps below: In 3D view: 1.
Page 135: Chart Set-Up Menu Options
12.14 Chart set-up menu options The following table describes the various options in the Chart Set-up Menu for your multifunction display. Menu item Description Options Context Menu (Touchscreen displays only) Determines how the context menu is accessed • Touch — touching a chart object opens the using touch context menu.
Page 136 Cartography set-up menu options The following table describes the various options in the Cartography Set-up Menu for your multifunction display. Menu item Description Options Chart Display Determines the level of detail shown on the chart. • Simple • Detailed (default) •...
Page 137 Menu item Description Options Nav. Marks Symbols Determines which set of navigation mark symbols is used — • International (default) International, or US. These symbols correspond to paper charts. • US Light Sectors Determines whether the sector of light cast by a fixed beacon is •...
Page 138 New a Series / New c Series / New e Series...
Page 139: Chapter 13 Using Radar
Chapter 13: Using radar Chapter contents • 13.1 Radar overview on page 140 • 13.2 Radar scan speed on page 141 • 13.3 Radar scanner status symbols on page 141 • 13.4 Radar range and image quality on page 142 •...
Page 140: Radar Overview
Correction application will function. Note: Features not listed are supported by all types of Raymarine Radar Features Non-HD Digital, HD and SuperHD radars. Depending on the type of Raymarine radar you have different...
Page 141: Radar Scan Speed
Selecting radar scan speed When you return to transmit mode, the magnetron does not need to warm up again. The speed option requires a 48 RPM compatible Raymarine HD This is the default mode. radome or Raymarine SuperHD open array radar scanner.
Page 142: Radar Range And Image Quality
13.4 Radar range and image quality Maximum radar range The usable range of the radar is limited by factors such as the height of the scanner, and height of the target. Maximum radar range is essentially line-of-sight, so is limited by the height of the scanner and the height of the target as illustrated below: R ma x...
Page 143 Blind Sectors Obstructions such as funnels and masts near the radar antenna may obstruct the radar beam and cause radar shadows or ‘blind sectors’. If the obstruction is relatively narrow, there will be a reduction of the beam intensity, though not necessarily a complete cut-off.
Page 144: Radar Display Overview
13.5 Radar display overview Sea clutter With your radar scanner connected and the radar in transmit mode, the radar picture provides a map-like representation of the area in which the radar is operating. Sea clutter in auto D12207-2 Item Description Range On-screen controls (Touchscreen multifunction displays Interference...
Page 145: Dual Range Radar Operation
13.6 Dual range radar operation that the size of a target on screen is dependent on many factors and may not necessarily be proportional to its physical size. Nearby objects may appear to be the same size as distant larger objects. The Dual Range radar function enables you to view 2 ranges at the same time in separate windows.
Page 146: Radar Mode And Orientation
13.7 Radar mode and orientation Scanner Dual Range mode Operating mode 4 Kw SuperHD Open Long SuperHD Radar orientation modes Array The radar can operate in a number of orientation modes to suit Short different types of navigation. Long 12 Kw SuperHD Open SuperHD The orientation of the radar refers to the relationship between the Array...
Page 147 Course-Up The default motion mode is “Relative”, with zero offset. True Motion (TM) When the motion mode is set to True, fixed radar targets maintain a constant position and moving vessels (including your vessel) travel in true perspective to each other and to fixed landmasses on the screen.
Page 148: Radar Tuning: On-Screen Gain Controls
13.8 Radar tuning: On-screen gain controls Touchscreen multifunction displays provide on-screen access to controls for Gain, Rain and Sea clutter. Gain control Rain control Sea control Note: non-touchscreen controls are accessed by the menu options: Menu > Rain and Menu > Adjust Gain. Enabling and disabling on-screen gain controls You can enable and disable the on-screen gain controls by following...
Page 149: Radar Adjustments: Hd And Superhd Scanners
Adjusting radar preset gain 2. Select Adjust Gain <Mode>, where <Mode> shall be the Auto Gain mode already selected. Raymarine strongly recommends the use of the preset gain 3. Select Col: . modes to achieve optimum results. However if required manual adjustments can be made.
Page 150 Adjusting radar anti sea clutter From the radar application, with the required Auto Gain Mode selected: 1. Select Menu. 2. Select Adjust Gain <Mode>, where <Mode> shall be the Auto Gain mode already selected. 3. Select Sea: . 4. The Sea clutter slider bar control is displayed. 5.
Page 151: Radar Adjustments: Non-Hd Digital Radomes
• Harbor — this is the default mode. This setting Raymarine strongly recommends the use of these takes account of land clutter so that smaller presets to achieve optimum results. However, you targets, like navigation buoys, are not lost.
Page 152: Radar Presentation Menu Options
13.11 Radar presentation menu options Function Description Options Dual Range This menu item allows you to turn Dual range mode On and Off. • On • Off Dual Range Channel This menu item allows you to choose long or short channel for dual range. •...
Page 153 Function Description Options Data Overlay Set-up This menu item contains a sub-menu which enables you to turn on and select Data Cell 1 & 2 information to display in data cells located on the bottom left of the radar application •...
Page 154: Using Radar To Measure Distances, Ranges, And Bearings
13.12 Using radar to measure distances, A Variable Range Marker (VRM) is a circle centred on your vessel’s position and fixed with respect to the heading mode. When this ranges, and bearings circle is adjusted to align with a target, its range from your vessel is measured and displayed on the Radar context menu when you When you are using the radar application, you can measure select the VRM with the cursor.
Page 155 VRM/EBL context menu 1. Position the cursor over the VRM/EBL. The VRM/EBL function includes a context menu which provides 2. Press the Ok button. positional data and menu items. The radar context menu is displayed. 3. Use the Rotary Control to select Float Center. 4.
Page 156: Using Radar To Track Targets And Avoid Collisions
The Width numeric adjust control is displayed. the quality of the heading and speed data, the better MARPA will perform. For the best heading data, a Raymarine SMART heading 14. Adjust the width of the guard zone in degrees. sensor or a gyro-stabilized autopilot is required.
Page 157 • The target echo is weak. The target is very close to land, buoys i. Selecting a location, object or target on-screen and pressing or other large targets. the Ok button. 2. Touchscreen multifunction displays: • The target or your own vessel is making rapid manoeuvres. i.
Page 158 Vessel vectors (CPA graphics) overview CPA graphics show vectors for your vessel and a selected target. A vector is a line on-screen showing the predicted courses of your vessel and the selected target if you both remain on your present course.
Page 159: Scanner Set-Up Menu Options
Tune Adjust This menu item allows you to fine tune the radar scanner's receiver for maximum returns on the display. Raymarine recommends that this function is set to Auto. • Auto If you set this function to Manual and adjust the setting shortly after powering up the radar scanner, you should adjust it again approximately 10 minutes after •...
Page 160: Resetting The Radar
13.15 Resetting the radar To reset radar settings to defaults follow the steps below: From in the radar application: 1. Select Menu. 2. Select Scanner Set-up. 3. Select Advanced Set-up. 4. Select Reset Advanced. A confirmation pop up message is displayed. 5.
Page 161: Chapter 14 Using Ais
Chapter 14: Using AIS Chapter contents • 14.1 AIS overview on page 162 • 14.2 AIS prerequisites on page 163 • 14.3 AIS context menu on page 163 • 14.4 Enabling AIS on page 164 • 14.5 Displaying AIS vectors on page 164 •...
Page 162: Ais Overview
14.1 AIS overview AIS Simulator Mode Raymarine recommends that you use the simulator function to The AIS feature enables you to receive information broadcast by familiarize yourself with the AIS features. When the simulator other vessels, and to add these vessels as targets in the chart and function is enabled (homescreen >...
Page 163: Ais Prerequisites
14.2 AIS prerequisites 14.3 AIS context menu You must have suitable AIS hardware connected to your The AIS function includes a context menu which provides AIS target multifunction display to make use of the AIS functionality. information and menu items. In order to run AIS, you will need: •...
Page 164: Enabling Ais
14.4 Enabling AIS 14.5 Displaying AIS vectors You must have the correct data available before AIS vectors can Enabling AIS in the chart application be displayed. To enable AIS overlay in the chart application the chart view must A target is defined as active when it has the following data displayed be set to 2D Menu >...
Page 165: Ais Status Symbols
14.6 AIS status symbols 14.7 AIS silent mode AIS status is indicated by a symbol in the databar. AIS silent mode enables you to disable AIS transmissions AIS silent mode enables you to disable the transmitting functions Symbol Description of your AIS equipment. This is useful when you do not want to AIS unit is switched on and operating.
Page 166: Ais Target Symbols
14.8 AIS target symbols 14.9 Displaying detailed AIS target information Your multifunction display shows a range of symbols to represent the different types of AIS target. From the chart or radar application: Target type Description Symbol 1. Select an AIS target. The AIS target context menu is displayed.
Page 167: Viewing All Ais Targets
14.10 Viewing all AIS targets 14.11 Using AIS to avoid collisions You can use the AIS safe zone and safety message functions to From the chart application go to Menu > AIS Options help you avoid collisions with other vessels and objects. From the radar application go to Menu >...
Page 168: Ais Options
14.12 AIS options 2. Select Track Targets. 3. Select AIS Unit Set-up. The AIS options are accessible in the chart application by selecting 4. Select AIS Safety Messages. Menu > AIS Options > MARPA & AIS Options or the radar Selecting AIS Safety Messages will switch between safety application by selecting Menu >...
Page 169: Ais Alarms
14.14 Buddy tracking 14.13 AIS alarms The Buddy Tracking feature enables you to add AIS-equipped The AIS functions generate a number of alarms to alert you to friends and regular contacts to a “Buddy List” on your multifunction dangerous or lost targets. display.
Page 170 ii. Select No to save the vessel to your buddy list without entering a name for the buddy vessel. The vessel will now be added to your buddy directory. Adding a vessel to your buddy list from AIS target list 1.
Page 171: Chapter 15 Using The Fishfinder
Chapter 15: Using the fishfinder Chapter contents • 15.1 How the fishfinder works on page 172 • 15.2 Raymarine sonar modules on page 172 • 15.3 Traditional sonar technology on page 173 • 15.4 Broadband CHIRP sonar technology on page 173 •...
Page 172: How The Fishfinder Works
15.2 Raymarine sonar modules 15.1 How the fishfinder works The fishfinder application uses a sonar module and a suitable sonar The table below lists Raymarine’s sonar modules and whether transducer. The sonar module interprets signals from the transducer CHIRP technology is used.
Page 173: Traditional Sonar Technology
15.3 Traditional sonar technology 15.4 Broadband CHIRP sonar technology Traditional sounders use a single carrier frequency or carrier wave Broadband sonars use a swept frequency 'CHIRP' signal which can for the sonar ping. These sounders work by measuring the time it distinguish between multiple close targets, this enables the sonar to takes the ping echo to return to the transducer to determine target display multiple targets instead of large combined targets.
Page 174: Fishfinder Introduction
15.5 Fishfinder introduction Fishfinder context menu The fishfinder application includes a context menu which provides Warning: Sonar operation fishfinder information and shortcuts to menu items. • NEVER operate the sonar with the vessel out of the water. • NEVER touch the transducer face when the sonar is powered on.
Page 175: Transducer Bandwidth
15.6 Transducer bandwidth 15.7 The sonar image The fishfinder application displays the fishfinder frequency, center Interpreting the seabed using sonar frequency or CHIRP mode depending on the connected sonar module and transducer. It is important to understand how to correctly interpret the seabed structure represented in the fishfinder display.
Page 176: Fishfinder Presets
15.8 Fishfinder presets The fishfinder provides you with four preset configurations available from the fishfinder menu. These enable you to quickly select appropriate settings tailored for various situations. Each preset has been configured to provide the best operating parameters for the fishfinder. However, it is possible to manually adjust the presets if necessary.
Page 177: Dual / Single Frequency Fishfinder
15.9 Dual / Single frequency fishfinder 15.10 Non-CHIRP (traditional) sonar module frequency controls Dual frequency operation allows the sonar to operate and display 2 frequencies simultaneously. If the preset mode that you are using The frequency of the sonar determines the width of the sonar beam, has two frequencies configured, you can view either one or both of the depth to which the signals will penetrate and the resolution of those frequencies in separate windows.
Page 178: Chirp Sonar Module Frequency Controls
15.11 CHIRP sonar module frequency The graph above depicts an example of the fine tuning (from —50% to +50%) available when the frequency is set to 200 kHz. controls Tuning the fishfinder frequency (non-CHIRP sonar module) The frequency of the sonar determines the width of the sonar beam, When connected to a non-CHIRP sonar module you can manually the depth to which the signals will penetrate and the resolution of tune the fishfinder frequency.
Page 179 Frequency adjustment (CHIRP sonar module in non-CHIRP mode) When using a CHIRP sonar module in CHIRP mode (Low Chirp, Med Chirp or High Chirp) the frequency cannot be adjusted. When using a CHIRP sonar module in a non-Chirp mode (e.g. 50 kHz or 160 kHz) the frequency at which the transducer is transmitting can be adjusted.
Page 180: Fishfinder Display Modes
15.12 Fishfinder display modes 6. Adjust the setting to the required value. 7. Select Back or use the Ok button to confirm the setting. Selecting a fishfinder display mode Adjusting the position of the fishfinder zoomed area From the fishfinder application: When the zoom function is selected, the system automatically 1.
Page 181: Fishfinder Range
15.13 Fishfinder range Bottom Lock The Bottom Lock function applies a filter to flatten the image of the The Range and Range Shift functions enable you to change the seabed and make any objects on or just above it easier to discern. range of depth displayed by the fishfinder.
Page 182: Fishfinder Sensitivity Settings
The range shift dialog is displayed. For Raymarine sonar modules which do not have CHIRP capabilities 4. Adjust the setting to the require value. there are three Auto modes, each suited to different scenarios: 5.
Page 183 1. Select the on-screen Gain control located on the left hand side TVG Presets and auto settings of the fishfinder application. When connected to a Raymarine CHIRP sonar module 3 preset 2. Select the Auto box to switch between Auto and Manual gain. TVG options are available: 3.
Page 184 Selecting the TVG Auto setting Setting the frequency for TVG using the on-screen controls The Auto setting for TVG is only available on Raymarine non-CHIRP When connected to a Raymarine CHIRP sonar module, the TVG sonar modules.
Page 185: Fishfinder Presentation Options
Setting the frequency for power mode the seabed. This helps to distinguish objects When connected to a Raymarine CHIRP sonar module, the power mode for frequency 1 and frequency 2 can be changed close to the bottom. independently or both at the same time. If connected to a...
Page 186: Depth And Distance With The Fishfinder
15.16 Depth and distance with the Menu Item Description Options fishfinder Allows selection of a • Select Data Category data type by category. Data Cell 2 The fishfinder display provides a number of features to help you • Data Cell 2 determine depths and distances.
Page 187: Fishfinder Scrolling
15.17 Fishfinder scrolling The fishfinder image scrolls from right to left. You can pause the scrolling or adjust the scroll speed, to ease placing of waypoints or VRMs on-screen. Scroll speed You can adjust the speed at which the fishfinder image scrolls. A faster speed provides more detail which may be useful when you are looking for fish.
Page 188: Fishfinder Waypoints
15.18 Fishfinder waypoints 15.19 Fishfinder alarms The display can be configured to provide a number of fishfinder Placing a waypoint on the fishfinder display enables you to mark a alarms. position so that you can return to it later. The following fishfinder alarms can be set when a sonar module is When a waypoint is placed, its details are added to the waypoint detected, or when the simulator is on: list and a vertical line labelled WPT is displayed on-screen.
Page 189: Sounder Set-Up Menu Options
15.20 Sounder set–up menu options This section describes the settings you can change using the sounder set up menu: (Menu > Set-up > Sounder Set-up). The set up menu contains settings that are likely to be changed infrequently. Menu Item Description Options Internal Sounder...
Page 190: Transducer Set-Up Menu Options
15.21 Transducer set-up menu options The Transducer Set-up menu should be used when setting up your multifunction display for the first time or when installing a depth transducer. Menu Item Description Options Transducer Select the appropriate transducer type from those displayed. Options available are dependant on the sonar module Some transducer may be detected by the system automatically.
Page 191: Resetting The Sonar
The reset function restores the unit to its factory default values. Note: Performing a factory reset will clear speed and temperature calibration settings and the depth offset. 1. Using a compatible Raymarine multifunction display go to the Fishfinder application page. 2. Select Menu from the side menu.
Page 192 New a Series / New c Series / New e Series...
Page 193: Chapter 16 Using The Data Application
Chapter 16: Using the data application Chapter contents • 16.1 Data application overview on page 194 • 16.2 Pre-configured datapages on page 194 • 16.3 Customizing the data application on page 196 Using the data application...
Page 194: Data Application Overview
Default page data items e95 / e97 / c95 / c97 / e125 / Datapage a65 / a67 / e7 / e7D e127 / c125 / c127 / e165 Navigation • COG & SOG •...
Page 195 / e97 / c95 / c97 / e125 / e95 / e97 / c95 / c97 / e125 / Datapage a65 / a67 / e7 / e7D e127 / c125 / c127 / e165 Datapage a65 / a67 / e7 / e7D...
Page 196: Customizing The Data Application
16.3 Customizing the data application You can customize the data application to show the system and instrument data that you require. In addition to displaying the default, pre-configured datapages in the data application, you can also: • Change the order datapages appear. •...
Page 197 Customizing datapage content From the data application: 6. Select the data item you want to display. 1. Select Menu. Once selected a tick will be placed next to the data item in the menu and the cell on screen will display the new data item 2.
Page 198 Data Category Description Data Item Digital Dial Graphical Fuel Types of data related Fuel Level 1 (vol) to the fuel system. For example, fuel levels. Fuel Level 2 (vol) Note: The options displayed are Fuel Level 3 (vol) dependant on the number of engines set Fuel Level 1 (%) in the data application.
Page 199 Data Category Description Data Item Digital Dial Graphical Navigation Types of data related to Cursor Position (Only navigation. For example, available in the Databar bearing to waypoint. and data overlay.) Cursor info Cross Track Error Rolling Road (Only available in the Data application.) Compass Target Position...
Page 200 7. Select the data item you want to display. 4 Engines Once selected a tick will be placed next to the data item in the menu and the cell on screen will display the selected data item. 8. Repeat steps 3 to 6 for all the data items you want to change. 9.
Page 201 Datapage and dial colors Datapage color theme and dial colors can be switched between light and dark. Color Theme Dial Color Example Light Light Light Dark Dark Dark Dark Light Resetting all datapages You can reset the datapages in the data application to the factory defaults.
Page 202 New a Series / New c Series / New e Series...
Page 203: Chapter 17 Using The Fuel Manager
Chapter 17: Using the fuel manager Chapter contents • 17.1 Fuel manager overview on page 204 Using the fuel manager...
Page 204: Fuel Manager Overview
17.1 Fuel manager overview Note: Fuel manager estimates the amount of fuel onboard, based on The fuel manager provides an estimate of fuel remaining, and the the user logging each time you fill up, the total fuel capacity, and distance and time which can be travelled before the tanks are how much fuel is burned by the engine(s).
Page 205 5. Select Fuel Level. 1. Select Menu. The fuel level numeric adjust control is displayed. 2. Select Presentation. 6. Adjust the fuel level to the required value. 3. Select Layers. 4. Select Fuel Range Ring. The low fuel alarm will now be sounded when the fuel remaining in the tank falls to the value specified.
Page 206 New a Series / New c Series / New e Series...
Page 207: Chapter 18 Using The Weather Application (North America Only)
Chapter 18: Using the weather application (North America only) Chapter contents • 18.1 Weather application overview on page 208 • 18.2 Weather application set up on page 208 • 18.3 Weather application display overview on page 209 • 18.4 Weather map navigation on page 212 •...
Page 208: Weather Application Overview
The weather application can only be used in North America and • Your multifunction display must be connected to a Raymarine its coastal waters. Sirius weather receiver. The weather application graphics and their associated weather data •...
Page 209: Weather Application Display Overview
18.3 Weather application display Symbol Description overview Lightning — a lightning symbol is shown at each cloud-to-ground strike: The weather application displays a range of graphics to indicate • Light (recorded in last 10–15 weather conditions and forecast information. minutes.) The following diagram illustrates the main features of the weather application display: •...
Page 210 Wind speed symbols Forecast Historical (grey) Current (red) (orange) Description The weather application uses a range of symbols to represent different wind speeds. Hurricane (Category 1–5) Symbol Speed Symbol Speed Symbol Speed Tropical storm 3–7 kts 8–12 kts 13–17 kts Tropical disturbance, tropical...
Page 211 NOWRad precipitation color codes Reflectivity Intensity Rainfall (mm/hr) Rainfall (in/hr) NOWRad displays the type and level of precipitation: 15376.51 599.69 Color code Precipitation type Reflectivity Intensity 31575.91 1231.46 Light green Rain (15 to 19 dBz) 64841.98 2528.84 Medium green Rain (20 to 29 dBz) 133154.6 5193.03...
Page 212: Weather Map Navigation
18.4 Weather map navigation 18.5 Weather context menu You can move around the weather map and place waypoints. The weather application includes a context menu which provides positional data and the option to view weather reports from the When you open the weather application, a world map is displayed. If cursor location.
Page 213: Weather Information
18.7 Weather reports 18.6 Weather information You can view weather information for: You can view a number of different weather reports to give you a comprehensive view of the weather. • a specific location Your multifunction display shows weather reports for: •...
Page 214: Animated Weather Graphics
18.8 Animated weather graphics You can view animated weather graphics to provide an indication of changing weather patterns. The animated weather option enables you to view an animation from the current time for: • NOWRad — weather radar • Wind •...
Page 215: Weather Application Menu Options
18.9 Weather application menu options Menu item Description Options Watchbox Alert The Watchbox Alerts Alert Range The following options are available from the weather application menu allows you to turn menu: • Off alerts Off, or select a Menu item Description Options range.
Page 216: Glossary Of Weather Terms
18.10 Glossary of weather terms Term Definition Cold front The boundary between two different air masses where cold air pushes warm air out of the way and brings colder weather. Cyclone A large area of low atmospheric pressure, characterized by inward spiralling winds. A “low” also called a “depression”. Also the name used for a hurricane in the Indian Ocean and Western Pacific.
Page 217 Term Definition Wave cyclone A storm or low pressure centre that moves along a front. Wave period The period is the time gap between successive waves and the longer the period the faster the waves travel. Using the weather application (North America only)
Page 218 New a Series / New c Series / New e Series...
Page 219: Chapter 19 Using The Thermal Camera Application
Chapter 19: Using the thermal camera application Chapter contents • 19.1 Thermal camera application overview on page 220 • 19.2 Thermal camera image on page 220 • 19.3 Controls overview on page 221 • 19.4 Camera control on page 222 •...
Page 220: Thermal Camera Application Overview
19.1 Thermal camera application 19.2 Thermal camera image overview The thermal camera provides a video image which is shown on your display. The thermal camera application enables you to control a connected thermal camera and display its image on your multifunction display. Thermal imaging (also known as infrared) cameras enable you to see clearly in low-light and no-light conditions.
Page 221: Controls Overview
Icon Description The thermal camera application is available on compatible Rear-view mode — image is flipped horizontally. Raymarine multifunction displays and systems. It includes controls for the thermal camera. Thermal camera application – hardkey controls Zoom setting: 2x zoom. Rotary control Zoom image in / out.
Page 222: Camera Control
19.4 Camera control • JCU Icon • PC Icon Power up and standby • Restore Factory Defaults When the breaker connecting power to the camera is switched on, the camera will run a boot up sequence lasting for about 1 minute, •...
Page 223 Thermal camera stabilization 2. Select Menu. 3. Select Camera Set-up. The Raymarine T470SC and T473SC thermal cameras includes a 4. Select Set Home Position. mechanical stabilization feature. The “Home” icon flashes on-screen to indicate that a new home The mechanical stabilization feature improves image stability by position has been set.
Page 224: Image Adjustments
19.5 Image adjustments Thermal camera point mode Point mode is only applicable to thermal cameras which have Adjusting the thermal camera image mechanical stabilization. Enabling point mode only has significance when stabilization With the thermal camera application displayed: is enabled. Enabling point mode turns off the horizontal (pan) 1.
Page 225 Thermal camera reverse video Thermal camera rear view mode The rear view mode flips the video image horizontally, providing a You can reverse the polarity of the video image to change the appearance of objects on-screen. “mirror image”. This is useful for example in instances where the camera is The reverse video option (video polarity) switches the thermal image from white-hot (or red-hot if the color mode setting is active) rear-facing and you are viewing the image on a forward-facing...
Page 226: Camera Set-Up Menu
19.6 Camera set-up menu 2. Select Camera Set-up. 3. Select Slew Settings. Set Home Position Sets the camera’s The Slew settings page is displayed which includes the following current position as the auto slew options: Camera Home position. • Auto Slew to MOB Slew Settings Provides automatic slew •...
Page 227 High Power Torque This option controls the • On (default) amount of power used to • Off hold the camera steady when in use. With the setting enabled the camera will consume more power, but will help ensure that the camera is held in place in rough seas.
Page 228 New a Series / New c Series / New e Series...
Page 229: Chapter 20 Using The Camera Application
Chapter 20: Using the camera application Chapter contents • 20.1 Camera application overview on page 230 Using the camera application...
Page 230: Camera Application Overview
20.1 Camera application overview 2. Move the Joystick Up to display the previous video feed. You can view a camera or a video feed which is connected directly Changing the camera / video feed using the to your multifunction display using the video input(s) or IP camera menu feeds which are available on your network.
Page 231 1. Select Menu > Camera Cycling > Camera Cycling so that Off is highlighted, or 2. Change the camera / video feed manually as described earlier in this section, or 3. Press the Back button (applicable to New c Series and New e Series only).
Page 232 New a Series / New c Series / New e Series...
Page 233: Chapter 21 Using Mobile Applications
Chapter 21: Using mobile applications Chapter contents • 21.1 Raymarine mobile apps on page 234 • 21.2 Enabling Wi-Fi on page 235 • 21.3 Enabling mobile apps on page 235 • 21.4 Setting up Wi-Fi security on page 236 •...
Page 234: Raymarine Mobile Apps
• Enable Wi-Fi in the System Settings on the multifunction display. • Enable Wi-Fi on your compatible device. • Select the Raymarine Wi-Fi connection from the list of available Wi-Fi networks on your compatible device. • Enable the relevant type of connection (i.e. Viewing or Remote Control) in the System Settings on the multifunction display.
Page 235: Enabling Wi-Fi
5. Select Viewing only to enable video streaming only, or 6. Select Remote Control to enable remote control and video streaming using. 7. Launch the relevant Raymarine mobile app on your tablet or smartphone device and follow the on-screen instructions. Using mobile applications...
Page 236: Setting Up Wi-Fi Security
— None, WPA only, WPA 2 only (default), or WPA/WPA 2. Note: • Raymarine strongly recommends the use of the WPA2 security setting. • Selecting None for your WiFi Security will leave your WiFi open and allow anyone with a WiFI enabled device access to your system.
Page 237: Chapter 22 Media Player Application
Chapter 22: Media player application Chapter contents • 22.1 Media player connection on page 238 • 22.2 Enabling Bluetooth on page 238 • 22.3 Pairing a Bluetooth media player on page 239 • 22.4 Enabling audio control on page 239 •...
Page 238: Media Player Connection
22.1 Media player connection 22.2 Enabling Bluetooth You can use your multifunction display to wirelessly control a With the homescreen displayed: Bluetooth-compatible media player (such as a smartphone). 1. Select Set-up. The media player must be compatible with the Bluetooth AVRCP 2.
Page 239: Pairing A Bluetooth Media Player
22.3 Pairing a Bluetooth media player 22.4 Enabling audio control With the homescreen displayed and Bluetooth turned on: With the homescreen displayed: 1. Select Set-up. 1. Select Set-up. 2. Select System Settings. 2. Select System Settings. 3. Select Wireless Connections. 3.
Page 240: Media Player Controls
Touchscreen multifunction displays enable you to use the on-screen media player controls to control the audio playing on your external You can control audio wirelessly using a Raymarine RCU-3 remote media player. control unit. The Shortcut key on the RCU-3 must be set to Start/Stop audio playback, refer to the Using a Remote control section for further details.
Page 241: Unpairing A Bluetooth Device
22.7 Unpairing a Bluetooth device If you are experiencing problems when attempting to use a Bluetooth device with the multifunction display it may be necessary to unpair the device (and any other paired Bluetooth devices) and then retry the pairing procedure. With the homescreen displayed: 1.
Page 242 New a Series / New c Series / New e Series...
Page 243: Chapter 23 Using A Remote Control
Chapter 23: Using a remote control Chapter contents • 23.1 Remote control connection on page 244 • 23.2 Pairing the remote and configuring the UP and DOWN buttons on page 244 • 23.3 Operating principles on page 245 • 23.4 Customizing the SHORTCUT button on page 245 •...
Page 244: Remote Control Connection
2. Bluetooth connection. 9. When prompted, press the arrow button on your remote that you 3. Raymarine Bluetooth remote control (for example, RCU-3). wish to be configured as the UP button. The other arrow button will automatically be configured as the DOWN button.
Page 245: Operating Principles
23.3 Operating principles 23.4 Customizing the SHORTCUT button Remote control operating principles. On your multifunction display, with the homescreen displayed: 1. Select Set-up. • Only 1 multifunction display may be operated by a remote control unit at any one time. You cannot pair a multifunction display to 2.
Page 246: Remote Control Functions
23.5 Remote control functions Bu tto n s Arrow buttons Shortcut button Ra n g e P a ir S e le c t D12051-2 Button Application where function available: Default functions: Chart Radar Fishfinder Weather Homescreen Range / zoom. •...
Page 247: Reconnecting The Rcu
23.6 Reconnecting the RCU 1. When you pair the RCU-3 with a multifunction display a wireless connection is established. 2. When you power off the multifunction display it loses its connection with the RCU-3 after 10 minutes. 60 5 M inutes 3.
Page 248 New a Series / New c Series / New e Series...
Page 249: Chapter 24 Dsc Vhf Radio Integration
Chapter 24: DSC VHF radio integration Chapter contents • 24.1 Using a DSC VHF radio with your display on page 250 • 24.2 Enabling DSC VHF radio integration on page 250 DSC VHF radio integration...
Page 250: Using A Dsc Vhf Radio With Your Display
24.1 Using a DSC VHF radio with your 24.2 Enabling DSC VHF radio integration display With the homescreen displayed: 1. Select Set-up. You can connect your DSC VHF radio to your multifunction display and show distress message information and GPS position data for 2.
Page 251: Chapter 25 Customizing Your Display
Chapter 25: Customizing your display Chapter contents • 25.1 Language selection on page 252 • 25.2 Boat details on page 253 • 25.3 Units set-up on page 254 • 25.4 Time and Date set-up on page 255 • 25.5 Display preferences on page 256 •...
Page 252: Language Selection
25.1 Language selection The system can operate in the following languages: English (US) English (UK) Arabic Chinese Croatian Danish Dutch Finnish French German Greek Italian Japanese Korean Norwegian Polish Portuguese (Brazilian) Russian Spanish Swedish Turkish With the homescreen displayed: 1. Select Customize. 2.
Page 253: Boat Details
• 0.1 to 5.0 (if Depth Units preferences set to your vessel. Fathoms) Note: Raymarine recommends adding some contingency from the actual hull clearance to the value selected. Total Fuel Capacity Allows you to specify the total fuel capacity of your vessel, this is required in order to enable the fuel manager function.
Page 254: Units Set-Up
25.3 Units set-up You can specify your preference for the units of measurement that will be used in all applications. Menu item Description Options Distance Units The units of measure that will be used in all applications for the • Nautical Miles display of all values related to distance.
Page 255: Time And Date Set-Up
25.4 Time and Date set-up You can specify your preference for the way that time and date will appear in all applications. Menu item Description Options Date Format Allows you to specify the preferred format for the display of date •...
Page 256: Display Preferences
25.5 Display preferences You can specify your preference for general display behavior. Menu item Description Options Key Beep An audible sound can be made each time a button is pressed or • ON (default) the touchscreen is used. • OFF Cursor Autohide If set to On, the cursor will be automatically hidden after a period •...
Page 257 Multiple brightness groups can be configured. This can reflect the physical location of the units on your vessel if required. For example, the units at your helm can be set to one group, and the units on the flybridge can be set to a different group. In this example, any brightness adjustments made to a unit at the helm would be automatically reflected in the other units at the helm but not on the flybridge.
Page 258: Data Cell And Databar Customization
25.6 Data cell and databar customization You can customize the data displayed in on-screen cells with a wide range of data. Customizable data is displayed in the databar, extended databar Displaying status icons in the databar (HybridTouch displays only) or data cells areas of the screen. Touchscreen multifunction displays enable you to display status The databar, extended databar and data cells are available in all icons in the databar.
Page 259 List of data items Depending on connected devices the categories of data available to display in the data application, data overlay, databar, and expanded databar are shown below. The following table shows the data items available by category. Data Category Description Data Item Digital...
Page 260 Data Category Description Data Item Digital Dial Graphical Fuel Types of data related Fuel Level 1 (vol) to the fuel system. For example, fuel levels. Fuel Level 2 (vol) Note: The options displayed are Fuel Level 3 (vol) dependant on the number of engines set Fuel Level 1 (%) in the data application.
Page 261 Data Category Description Data Item Digital Dial Graphical Navigation Types of data related to Cursor Position (Only navigation. For example, available in the Databar bearing to waypoint. and data overlay.) Cursor info Cross Track Error Rolling Road (Only available in the Data application.) Compass Target Position...
Page 262: System Set-Up Menus
Enables you to configure all the different types of alarms produced by the display and connected equipment. Pilot Controls Displays the Pilot Control dialog. Only available when a Raymarine autopilot is detected on the system and Autopilot Control is set to On. Fuel Manager Displays the Fuel manager page Audio Controls Displays the audio controls pop-up.
Page 263 Alarms menu Menu item Description Options MOB Data Type Determines whether Position or Dead Reckoning (DR) data is displayed. • Dead Reckoning Assuming that your vessel and the MOB are subject to the same tide and • Position (default) wind effects, the Dead Reckoning setting normally gives a more accurate course.
Page 264 Menu item Description Options • Deep Fish Limit — Specifies the upper value for the Fish Alarm Depth Shallow Fish Limit Limit. • 2 ft (or equivalent units) to the maximum of the transducer range Deep Fish Limit • 2 ft (or equivalent units) to the maximum of the transducer range Fuel Manager In the fuel manager alarm options you can switch the low fuel warning...
Page 265: System Settings Menu
Ground trip resets menu This menu enables you to resets the chosen ground trip distance counter to zero. Menu item Description Ground Trip 1 Reset Resets the ground trip 1 distance counter to zero. Ground Trip 2 Reset Resets the ground trip 2 distance counter to zero. Ground Trip 3 Reset Resets the ground trip 3 distance counter to zero.
Page 266 NOT compliant. It may be necessary to upgrade the • Heading. software for these non-compliant products to make them compliant. Visit the Raymarine website (www.raymarine.com) to obtain the • Depth. latest software for your products. If MDS-compliant software is not •...
Page 267 Connections menu This menu enables you to connect wireless Bluetooth and Wi-Fi devices to the display. Menu item Description Options Bluetooth Enable or disable Bluetooth on the display. • On • Off (default) Enable or disable Wi-Fi on the display. Wi-Fi •...
Page 268 To enter your own compensation value, use the Manual option, then specify the value using the Manual Variation setting (see below). This value is also transmitted to any other connected Raymarine instruments. Manual Variation • Range: 0 to 30 degrees, East or West...
Page 269 , it will automatically correlate each time you change the datum on the multifunction display. • If you have a Raymarine GPS receiver using NMEA 0183, or a third-party GPS receiver, you must correlate it separately. It may be possible to use your multifunction display to correlate an NMEA 0183 GPS receiver.
Page 270 Compatibility Compatibility mode should be used when connecting the display • On to a system which includes any of the following Raymarine • Off multifunction displays: E90W, E120W, E140W or a G-Series (GPM400) system. Not all functions will be available refer to the Network constraints sections.
Page 271: Chapter 26 Maintaining Your Display
Chapter 26: Maintaining your display Chapter contents • 26.1 Service and maintenance on page 272 • 26.2 Cleaning on page 272 Maintaining your display...
Page 272: Service And Maintenance
26.2 Cleaning This product contains no user serviceable components. Please Best cleaning practices. refer all maintenance and repair to authorized Raymarine dealers. When cleaning this product: Unauthorized repair may affect your warranty. • Do NOT wipe the display screen with a dry cloth, as this could Routine equipment checks scratch the screen coating.
Page 273: Chapter 27 Troubleshooting
Chapter 27: Troubleshooting Chapter contents • 27.1 Troubleshooting on page 274 • 27.2 Power up troubleshooting on page 275 • 27.3 Radar troubleshooting on page 276 • 27.4 GPS troubleshooting on page 277 • 27.5 Sonar troubleshooting on page 278 •...
Page 274: Troubleshooting
All Raymarine products are, prior to packing and shipping, subjected to comprehensive test and quality assurance programs. However, if you experience problems with the operation of your product this section will help you to diagnose and correct problems in order to restore normal operation.
Page 275: Power Up Troubleshooting
27.2 Power up troubleshooting Problems at power up and their possible causes and solutions are described here. Problem Possible causes Possible solutions Power supply problem. The system (or part of it) does not start up. Check relevant fuses and breakers. Check that the power supply cable is sound and that all connections are tight and free from corrosion.
Page 276: Radar Troubleshooting
Check power source is of the correct voltage and sufficient current (using voltage booster if appropriate). SeaTalk / RayNet network problem Check that the Scanner is correctly connected to a Raymarine network switch or SeaTalk crossover coupler (as applicable). Check the status of the Raymarine network switch.
Page 277: Gps Troubleshooting
• Close proximity to transmitting equipment such as VHF radio. GPS installation problem. Refer to the installation instructions. Note: A GPS Status screen is available within the Setup menu of Raymarine multifunction displays. This provides satellite signal strength and other relevant information. Troubleshooting...
Page 278: Sonar Troubleshooting
Refer to the instructions supplied with the unit. SeaTalk / RayNet network problem. Check that the unit is correctly connected to a Raymarine network SeaTalk switch or crossover coupler (as applicable). Check the status of the Raymarine network switch (if applicable).
Page 279: Thermal Camera Troubleshooting
Erratic or unresponsive controls. Network problem. Check that the controller and thermal camera are correctly connected to the network. (Note: This may be a direct connection or via a Raymarine network switch.) Check the status of the Raymarine network switch.
Page 280: System Data Troubleshooting
Network problem Check that all required equipment is connected to the network.. from some but not all displays. Check the status of the Raymarine network Switch. Check that SeaTalk / RayNet cables are free from damage. Software mismatch between equipment Contact Raymarine technical support may prevent communication.
Page 281: Video Troubleshooting
27.8 Video troubleshooting Problems with the video inputs and their possible causes and solutions are described here. Problem Possible causes Possible solutions No signal message on screen (video Cable or connection fault Check that the connections are sound and free from corrosion. image not displayed) Troubleshooting...
Page 282: Wi-Fi Troubleshooting
Ensure that the “Wi-Fi” option is enabled on the iPhone (available from the phone's Settings menu). Ensure that the Raymarine connection is selected as the W-iFi network. If a passcode has been specified for the multifunction display's Wi-Fi connection ensure that the same passcode is entered into the iPhone when prompted.
Page 283: Bluetooth Troubleshooting
27.10 Bluetooth troubleshooting Aspects of the installation can cause problems with the data shared between wireless devices. Such problems, their possible causes and solutions are described here. Problem Possible causes Possible solutions No wireless connection. iPhone does not have a Bluetooth Ensure that Bluetooth is enabled on the multifunction display (Homescreen: connection established with the >...
Page 284: Touchscreen Troubleshooting
27.11 Touchscreen troubleshooting Problems with the touchscreen and their possible causes and solutions are described here. Problem Possible causes Possible solutions Touchscreen does not operate as Touch lock is enabled Use the Trackpad to turn off the touch lock on the home screen. expected Screen is not being operated with bare Bare fingers must make contact with the screen for correct operation.
Page 285: Miscellaneous Troubleshooting
• System crashes or other erratic behavior. Check that the power source is of the correct voltage and sufficient current. Software mismatch on system (upgrade Go to www.raymarine.com and click on support for the latest software required). downloads. Corrupt data / other unknown issue.
Page 286 New a Series / New c Series / New e Series...
Page 287: Chapter 28 Technical Support
Chapter 28: Technical support Chapter contents • 28.1 Raymarine customer support on page 288 • 28.2 Third-party support on page 288 Technical support...
Page 288: Raymarine Customer Support
Raymarine provides a comprehensive customer support service. Contact and support details for third-party suppliers can be found on You can contact customer support through the Raymarine website, the appropriate websites. telephone and email. If you are unable to resolve a problem, please Navionics use any of these facilities to obtain additional help.
Page 289: Chapter 29 Technical Specification
Chapter 29: Technical specification Chapter contents • 29.1 Technical specification on page 290 Technical specification...
Page 290: Technical Specification
The suitable fuse rating for the thermal breaker is dependent on the number of • Height (including bracket): 212 mm devices you are connecting. If in doubt (8.35 in.) consult an authorized Raymarine dealer • Depth (NOT including cables): 64 mm (2.52 in.) Power consumption •...
Page 291 Aspect Viewing angle • Left / Right: 60 degrees Network (SeaTalk • a65 / a67 / e7 / e7D = 1 x SeaTalk port. 100 Mbits/s. RayNet type connection. • Top / Bottom: 60 / 50 degrees • e95 / e97 / c95 / c97 / e125 / e127 / c125...
Page 292 • Navionics Gold+ • Navionics Platinum • Navionics Platinum+ • Navionics Fish'N Chip • Navionics Hotmaps Refer to the Raymarine website (www.raymarine.com) for the latest list of supported chart cards. New a Series / New c Series / New e Series...
Page 293: Chapter 30 Spares And Accessories
30.5 Video cables on page 296 • 30.6 Power cables on page 296 • 30.7 a65 / a67 spares on page 297 • 30.8 e7 e7D spares on page 297 • 30.9 e95 / e97 / c95 / c97 spares on page 298 •...
Page 294: Transducer Accessories
30.1 Transducer accessories 30.2 RayNet connector network cables Item Part number Notes Cable Part number P48 sonar transducer A102140 Transom mount. 1 m (3.28 ft) RayNet to SeaTalk A62360 (RJ45) cable P58 sonar transducer A102138 Transom mount. 3 m (9.84 ft) RayNet to SeaTalk A80151 1 m (3.28 ft) Minn Kota A62363...
Page 295: Seatalk Hs Network Cables
30.3 SeaTalk network cables 30.4 SeaTalk patch cables Cable Part number Cable Part number E55049 E06054 1.5 m (4.9 ft) SeaTalk network cable 1.5 m (4.9 ft) SeaTalk patch cable 5 m (16.4 ft) SeaTalk network cable E55050 5 m (16.4 ft) SeaTalk patch cable E06055 10 m (32.8 ft) SeaTalk...
Page 296: Video Cables
30.5 Video cables 30.6 Power cables The following video cable is required for the video in / out connector Cable Part number on the e95 / e97 / e125 / e127 variant multifunction displays. 1.5 m (4.9 ft) Straight power and data R62379 Part number Description...
Page 297: A65 / A67 Spares
30.8 e7 e7D spares 30.7 a65 / a67 spares Item Part number Notes Item Part number Notes Trunnion (bracket) R70147 Trunnion (bracket) A62358 mount kit mount kit Front bezel R70148 Documentation pack R62378 Suncover R70149 Flush mount panel set R62376 Power cable 1.5m...
Page 298: E95 / E97 / C95 / C97 Spares
30.9 e95 / e97 / c95 / c97 spares 30.10 e125 / e127 / c125 / c127 spares Item Part number Notes Item Part number Notes c/e series trunnion kit R70001 c/e series trunnion kit R70002 c/e series front bezel R7004 c/e series front bezel R7006...
Page 299: E165 Spares
30.11 e165 Spares Item Part number Notes e165 trunnion kit A80176 e165 front bezel R70126 e165 suncover R70127 e165 flush mount kit R70125 Spares and accessories...
Page 300 New a Series / New c Series / New e Series...
Page 301: Appendix A Nmea 0183 Sentences
Appendix A NMEA 0183 sentences The display supports the following NMEA 0183 sentences. These are applicable to NMEA 0183 and SeaTalk protocols. Sentence Description Transmit Receive Waypoint arrival alarm sentence ● Autopilot sentence ‘B’ ● ● Bearing and distance to waypoint ●...
Page 302: Appendix B Nmea 2000 Sentences
Appendix B NMEA 2000 sentences The display supports the following NMEA 2000 sentences. These are applicable to NMEA 2000, SeaTalk and SeaTalk 2 protocols. Message number Message description Transmit Receive Bridge ● ● ● 59392 ISO Acknowledgment ● ● 59904 ISO Request ●...
Page 303 Message number Message description Transmit Receive Bridge ● ● ● 130306 Wind data ● ● ● 130310 Environmental parameters ● 130311 Environmental parameters ● 130576 Small craft status ● ● ● 130577 Direction data ● 130578 Vessel speed components NMEA 2000 sentences...
Page 304: Appendix C Connectors And Pinouts
NMEA1 TX- Brown CanL NMEA1 RX+ White SeaTalk (not connected) NMEA1 RX- Green Note: Use only Raymarine cables when connecting to SeaTalk NMEA2 RX+ Orange / White NMEA2 RX- Orange / Green Video in/out connector VIDEO IN RG179 coaxial VIDEO RTN...
Page 305: Appendix D Software Releases
Appendix D Software releases Raymarine regularly updates its multifunction display software to introduce improvements, additional hardware support and user interface features. The table below details some of the important enhancements and which software revision they were introduced with. Multifunction displays...
Page 306 Multifunction displays Software version Applicable product manual compatibility Changes • Corrected the ability to select Tide and/or Current Station uisng the Find Nearest feature. • Added NMEA 0183 & SeaTalkng data monitors to the diagnostics features. • Increased touch area for Alarm pop-ups and Back buttons. V2.xx 81337–1 c95 / c97 / c125 / c127 / e7 / e7D...
Page 308 www.ra ym a rin e .c o m...

This manual is also suitable for:

A67 C97 C125 E7 C127 E95 ... Show all

Raymarine a65 Installation And Operation Instructions Manual

Chapter 1 Important Information

Chapter 2 Handbook Information

Chapter 3 Planning the Installation

Chapter 4 Cables and Connections

Chapter 5 Location and Mounting

Chapter 6 Getting Started

Chapter 7 Managing Display Data

Chapter 8 Using the Document Viewer

Chapter 9 Using Autopilot Control

Chapter 10 Using Alarms and MOB Functions

Chapter 11 Using Waypoints, Routes and Tracks

Chapter 12 Using the Chart

Chapter 13 Using Radar

Chapter 14 Using AIS

Chapter 15 Using the Fishfinder

Chapter 16 Using the Data Application

Chapter 17 Using the Fuel Manager

Chapter 18 Using the Weather Application (North America Only)

Chapter 19 Using the Thermal Camera Application

Chapter 20 Using the Camera Application

Chapter 21 Using Mobile Applications

Chapter 22 Media Player Application

Chapter 23 Using a Remote Control

Chapter 24 DSC VHF Radio Integration

Chapter 25 Customizing Your Display

Chapter 26 Maintaining Your Display

Chapter 27 Troubleshooting

Chapter 28 Technical Support

Chapter 29 Technical Specification

Chapter 30 Spares and Accessories

Appendix A NMEA 0183 Sentences

Appendix B NMEA 2000 Sentences

Appendix C Connectors and Pinouts

Appendix D Software Releases

Quick Links

Troubleshooting

Related Manuals for Raymarine a65

Summary of Contents for Raymarine a65