Raymarine a65 Installation And Operation Instructions Manual page 46

Digital radar cables
You will need a dedicated radar power and data digital cable and
SeaTalk hs network cables to connect your scanner to your system.
Connection
Radar scanner to power supply and
Raymarine network switch.
Raymarine network switch to
multifunction display.
Radar power and data digital cables
These cables contain the wires for a scanner's power and data
connections.
Cable
5 m (16.4 ft) Power and data digital
cable
10 m (32.8 ft) Power and data digital
cable
15 m (49.2 ft) Power and data digital
cable
25 m (82.0 ft) Power and data digital
cable
Note: The maximum length for the radar power and data digital
cable (including any extensions) is 25 m (82 ft).
Radar power and data digital extension cables
These cables extend the power and data digital cables for a
scanner's power and data connections.
Cable
2.5 m (8.2 ft) Power and data digital
cable
5 m (16.4 ft) Power and data digital
cable
10 m (32.8 ft) Power and data digital
cable
Note: The maximum length for the radar power and data digital
cable (including any extensions) is 25 m (82 ft).
Sonar connection
A sonar connection is required for fishfinder applications.
There are 2 types of connection required for fishfinder applications:
• Sonar module connection — converts the sonar signals
provided by the sonar transducer into data suitable for a marine
electronics system. The sonar variant multifunction displays
feature a built-in sonar, enabling you to connect the display
directly to a compatible sonar transducer. Non-sonar variants
require a connection to an external Raymarine sonar module.
Internal and external sonars require a connection to a compatible
sonar transducer.
• Sonar transducer connection — provides sonar signals to the
sonar module.
46
Required cable
Power and data digital cable. For
longer cable runs, extensions are
available in a variety of lengths.
SeaTalk hs network cables, available in
a variety of cable lengths.
Part number
A55076D
A55077D
A55078D
A55079D
Part number
A92141D
A55080D
A55081D
Sonar module connection
4
SeaT alk
SeaT alk
1. Rear connector panel of multifunction display (Non-sonar
variant).
2. Raymarine network switch.
3. Raymarine sonar module.
4. RayNet cable.
The multifunction display can be used with the following Raymarine
sonar modules:
• CP450C
• DSM300
• DSM30
Note: You can also connect a sonar variant multifunction display
to a Raymarine sonar module. This is useful in circumstances
where you need a higher powered sonar module for example.
You can only use one sonar transducer at any one time.
Sonar connected directly to the display
On smaller systems (with only one display and no other SeaTalk
RayNet devices) the sonar module may be connected directly to the
display without using a Raymarine network switch.
Note: You must ensure that the cable ends connected into
the display and sonar module have a locking / weather-tight
mechanism.
Compatible sonar transducers
The multifunction display is compatible with the following sonar
transducers:
• Raymarine P48.
• Raymarine P58.
• Minn Kota transducers Sonar variant Raymarine displays only),
via optional A62363 adaptor cable.
• Any 600 watt sonar-compatible transducer, via optional E66066
adaptor cable.
Sonar transducer connection — Sonar variant multifunction
displays
1
1. Rear connector panel of multifunction display (Sonar variant).
2. Sonar transducer cable.
3. Sonar transducer.
1
hs
/ RayNet
3
hs
/ RayNet
3
New a Series / New c Series / New e Series
2
D12255-1
hs /
D12256-1