Raymarine a65 Installation And Operation Instructions Manual page 44

Network cable connector types
There are 2 types of network cable connector — SeaTalk
RayNet.
SeaTalk
SeaTalk
via SeaTalk
RayNet connector — used for connecting
Raymarine network switches and SeaTalk
devices to the multifunction display via RayNet
cables. Also required for connecting a crossover
coupler if only one device is being connected to
the display's Network connector.
Network cable types
There are 2 types of SeaTalk
"network".
• Patch — for connecting the following devices to a Raymarine
network switch:
– Thermal camera via PoE injector.
– Additional Raymarine network switch.
– PC or laptop using Voyager planning software.
• Network — for connecting the following devices to a Raymarine
network switch:
– Sonar Module.
– SR100 Sirius weather receiver.
– Additional compatible Raymarine multifunction displays.
RayNet connector network cables
Cable
1 m (3.28 ft) RayNet to SeaTalk
(RJ45) cable
3 m (9.84 ft) RayNet to SeaTalk
(RJ45) cable
10 m (32.8 ft) RayNet to SeaTalk
(RJ45) cable
400 mm (1.3 ft) RayNet to RayNet
cable
2 m (6.56 ft) RayNet to RayNet cable
5 m (16.4 ft) RayNet to RayNet cable
10 m (32.8 ft) RayNet to RayNet cable
20 m (65.6 ft) RayNet to RayNet cable
50 mm (1.97 in) RayNet (male) to
RayNet (male) cable
400 mm (1.3 ft) RayNet to SeaTalk
(female) adaptor
RayNet cable puller 5 pack
SeaTalk hs network cables
Cable
1.5 m (4.9 ft) SeaTalk hs network cable
5 m (16.4 ft) SeaTalk hs network cable
10 m (32.8 ft) SeaTalk hs network cable
20 m (65.6 ft) SeaTalk hs network cable
SeaTalk hs patch cables
Cable
1.5 m (4.9 ft) SeaTalk hs patch cable
5 m (16.4 ft) SeaTalk hs patch cable
44
hs connector — used for connecting
hs devices to a Raymarine network switch
hs cables.
hs network cable — "patch" and
Part number
hs A62360
hs A80151
hs A80159
A80160
A62361
A80005
A62362
A80006
A80162
hs A80160
R70014
Part number
E55049
E55050
E55051
E55052
Part number
E06054
E06055
Cable
hs and
10 m (32.8 ft) SeaTalk
15 m (49.2 ft) SeaTalk
20 m (65.6 ft) SeaTalk
Radar connection
hs
The multifunction display is compatible with Raymarine Non-HD
digital radomes and HD / SuperHD radar scanners. The scanner is
connected using a SeaTalk
Note:
• New c Series and New e Series displays (excluding the e7
and e7D) can connect 2 SeaTalk
to the display.
• New a Series and the e7 / e7D displays can connect 1
SeaTalk hs / RayNet device directly to the display.
The radar is usually connected via a Raymarine network switch. On
smaller systems (with only one display and no other digital devices)
the radar may be connected to the display directly using a SeaTalk
crossover coupler.
Radar connected using Raymarine network switch
1. Radar scanner.
2. Raymarine network switch.
3. RayNet cable.
4. RayNet to SeaTalk
5. SeaTalk hs
6. VCM (Voltage Converter Module) — required for Open Arrays.
7. Power connection.
Part number
hs patch cable E06056
hs patch cable A62136
hs patch cable E06057
hs cable.
hs / RayNet devices directly
1
4
5
hs network cable.
crossover coupler
New a Series / New c Series / New e Series
hs
7 6
D12252-1