Operation; Removal; Installation - Chrysler Vehicle User Manual

TJ
CHILD RESTRAINT ANCHOR (Continued)
fixed lower anchors are integral to the rear seat back
frame and are accessed from the front of the rear
seat, where the seat back meets the seat cushion.
The two inboard lower anchors are constructed from
round steel bar stock that is formed into a U-shape,
then securely welded at each end to the rear seat
back frame. The two outboard lower anchors are
machined steel pins that are secured between the
two seat back hinge plates above the pivot pin on
each outboard side of the rear seat back frame. These
lower anchors cannot be adjusted or repaired and, if
faulty or damaged, they must be replaced as a unit
with the rear seat back frame.
WARNING: DURING AND FOLLOWING ANY SEAT
BELT OR CHILD RESTRAINT ANCHOR SERVICE,
CAREFULLY INSPECT ALL SEAT BELTS, BUCKLES,
MOUNTING HARDWARE, RETRACTORS, TETHER
STRAPS, AND ANCHORS FOR PROPER INSTALLA-
TION, OPERATION, OR DAMAGE. REPLACE ANY
BELT THAT IS CUT,
STRAIGHTEN ANY
TIGHTEN ANY LOOSE FASTENERS. REPLACE ANY
BELT THAT HAS A DAMAGED OR INOPERATIVE
BUCKLE OR RETRACTOR. REPLACE ANY BELT
THAT HAS A BENT OR DAMAGED LATCH PLATE
OR ANCHOR PLATE.
RESTRAINT ANCHOR OR THE UNIT TO WHICH THE
ANCHOR IS INTEGRAL THAT HAS BEEN BENT OR
DAMAGED. NEVER ATTEMPT TO REPAIR A SEAT
BELT OR CHILD
ALWAYS REPLACE DAMAGED OR FAULTY SEAT
BELT AND CHILD RESTRAINT COMPONENTS WITH
THE CORRECT, NEW AND UNUSED REPLACEMENT
PARTS LISTED IN THE DAIMLERCHRYSLER MOPAR
PARTS CATALOG.

OPERATION

See the owner's manual in the vehicle glove box for
more information on the proper use of all of the fac-
tory-installed child restraint anchors.

REMOVAL

The following procedure applies only to the rear
seat upper child tether anchors used on models
equipped with an optional rear seat. The child
restraint anchors used in this model in all other loca-
tions are integral to other components and cannot be
serviced separately.
WARNING: DURING AND FOLLOWING ANY SEAT
BELT OR CHILD RESTRAINT ANCHOR SERVICE,
CAREFULLY INSPECT ALL SEAT BELTS, BUCKLES,
MOUNTING HARDWARE, RETRACTORS, TETHER
STRAPS, AND ANCHORS FOR PROPER INSTALLA-
TION, OPERATION, OR DAMAGE. REPLACE ANY
FRAYED, OR
BELT THAT IS TWISTED.
REPLACE ANY
RESTRAINT COMPONENT.
BELT THAT
STRAIGHTEN
TIGHTEN ANY LOOSE FASTENERS. REPLACE ANY
BELT THAT HAS A DAMAGED OR INOPERATIVE
BUCKLE OR RETRACTOR. REPLACE ANY BELT
THAT HAS A BENT OR DAMAGED LATCH PLATE
OR ANCHOR
RESTRAINT ANCHOR OR THE UNIT TO WHICH THE
ANCHOR IS INTEGRAL THAT HAS BEEN BENT OR
DAMAGED. NEVER ATTEMPT TO REPAIR A SEAT
BELT OR
ALWAYS REPLACE DAMAGED OR FAULTY SEAT
BELT AND CHILD RESTRAINT COMPONENTS WITH
THE CORRECT, NEW AND UNUSED REPLACEMENT
PARTS LISTED IN THE DAIMLERCHRYSLER MOPAR
PARTS CATALOG.
(1) Remove the screw that secures the upper child
restraint tether anchor to the rear cargo floor panel
just forward of the tailgate opening sill (Fig. 14).
TORN.
CHILD
Fig. 14 Rear Upper Tether Anchor Remove/Install
1 - SCREW (2)
2 - FLOOR PANEL
3 - ANCHOR (2)
(2) Remove the upper tether anchor from the rear
cargo floor panel.

INSTALLATION

The following procedure applies only to the rear
seat upper child tether anchors used on models
equipped with an optional rear seat. The child
restraint anchors used in this model in all other loca-
tions are integral to other components and cannot be
serviced separately.
RESTRAINTS
IS CUT, FRAYED,
ANY BELT THAT
PLATE. REPLACE
CHILD RESTRAINT
8O - 13
OR TORN.
IS TWISTED.
ANY CHILD
COMPONENT.