Installation; Rear Seat Belt Buckle Removal - Chrysler Vehicle User Manual

TJ
REAR SEAT BELT & RETRACTOR (Continued)
(8) Remove the screw that secures the rear seat
belt retractor to the lower sport bar near the top of
the inner rear wheel house panel.
(9) Remove the rear seat belt and retractor from
the lower sport bar.

INSTALLATION

WARNING: DURING AND FOLLOWING ANY SEAT
BELT OR CHILD RESTRAINT ANCHOR SERVICE,
CAREFULLY INSPECT ALL SEAT BELTS, BUCKLES,
MOUNTING HARDWARE, RETRACTORS, TETHER
STRAPS, AND ANCHORS FOR PROPER INSTALLA-
TION, OPERATION, OR DAMAGE. REPLACE ANY
BELT THAT IS CUT,
STRAIGHTEN ANY
TIGHTEN ANY LOOSE FASTENERS. REPLACE ANY
BELT THAT HAS A DAMAGED OR INOPERATIVE
BUCKLE OR RETRACTOR. REPLACE ANY BELT
THAT HAS A BENT OR DAMAGED LATCH PLATE
OR ANCHOR PLATE.
RESTRAINT ANCHOR OR THE UNIT TO WHICH THE
ANCHOR IS INTEGRAL THAT HAS BEEN BENT OR
DAMAGED. NEVER ATTEMPT TO REPAIR A SEAT
BELT OR CHILD
ALWAYS REPLACE DAMAGED OR FAULTY SEAT
BELT AND CHILD RESTRAINT COMPONENTS WITH
THE CORRECT, NEW AND UNUSED REPLACEMENT
PARTS LISTED IN THE DAIMLERCHRYSLER MOPAR
PARTS CATALOG.
(1) Position the rear seat belt and retractor to the
lower sport bar near the top of the inner rear wheel
house panel (Fig. 38). Be certain to engage the loca-
tor tab on the retractor in the locator hole on the
sport bar.
(2) Install and tighten the screw that secures the
rear seat belt retractor to the lower sport bar.
Tighten the screw to 43 N·m (32 ft. lbs.).
(3) Position the rear seat belt turning loop to the
upper sport bar (Fig. 39).
(4) Install and tighten the screw that secures the
rear seat belt turning loop to the upper sport bar.
Tighten the screw to 43 N·m (32 ft. lbs.).
(5) Fold and snap the trim cover for the rear seat
belt turning loop back into place over the screw that
secures the turning loop to the upper sport bar.
(6) Position the rear seat belt lower anchor to the
inner rear wheel house panel.
(7) Install and tighten the screw that secures the
rear seat belt lower anchor to the inner rear wheel
house panel. Tighten the screw to 43 N·m (32 ft.
lbs.).
FRAYED, OR
BELT THAT IS TWISTED.
REPLACE ANY
RESTRAINT COMPONENT.
(8) Tumble the folded rear seat cushion and back
unit rearward onto the rear floor panel.
(9) Slide both rear seat belt buckle units between
the seat cushion and the seat back.
(10) Unfold the rear seat back from the seat cush-
ion until the seat back latch is fully engaged.
REAR SEAT BELT BUCKLE
REMOVAL
WARNING: DURING AND FOLLOWING ANY SEAT
BELT OR CHILD RESTRAINT ANCHOR SERVICE,
CAREFULLY INSPECT ALL SEAT BELTS, BUCKLES,
TORN.
MOUNTING HARDWARE, RETRACTORS, TETHER
STRAPS, AND ANCHORS FOR PROPER INSTALLA-
TION, OPERATION, OR DAMAGE. REPLACE ANY
BELT THAT
STRAIGHTEN
TIGHTEN ANY LOOSE FASTENERS. REPLACE ANY
CHILD
BELT THAT HAS A DAMAGED OR INOPERATIVE
BUCKLE OR RETRACTOR. REPLACE ANY BELT
THAT HAS A BENT OR DAMAGED LATCH PLATE
OR ANCHOR
RESTRAINT ANCHOR OR THE UNIT TO WHICH THE
ANCHOR IS INTEGRAL THAT HAS BEEN BENT OR
DAMAGED. NEVER ATTEMPT TO REPAIR A SEAT
BELT OR
ALWAYS REPLACE DAMAGED OR FAULTY SEAT
BELT AND CHILD RESTRAINT COMPONENTS WITH
THE CORRECT, NEW AND UNUSED REPLACEMENT
PARTS LISTED IN THE DAIMLERCHRYSLER MOPAR
PARTS CATALOG.
(1) Slide both rear seat belt buckle units between
the seat cushion and seat back into the rear cargo
area.
(2) Lift the rear seat back release lever and fold
the rear seat back forward, then tumble the folded
rear seat cushion and back unit forward against the
backs of the two front bucket seats.
(3) Lift the rear cargo area carpet between the two
rear seat belt buckle units far enough to access and
remove the screw that secures the anchor of the rear
seat belt buckle units to the rear cargo floor panel
through one of the clearance slots in the carpet (Fig.
40).
(4) Remove the rear seat belt buckle unit from the
rear floor panel through one of the clearance slots in
the rear cargo area carpet.
RESTRAINTS
IS CUT, FRAYED,
ANY BELT THAT
PLATE. REPLACE
CHILD RESTRAINT
8O - 33
OR TORN.
IS TWISTED.
ANY CHILD
COMPONENT.