Chrysler Vehicle User Manual page 368

TJ
CHARGING
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 21
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
DIAGNOSIS AND TESTING - CHARGING
SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SPECIFICATIONS
GENERATOR RATINGS
TORQUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
SPECIAL TOOLS . . . . . . . . . . . . . . . . . . . . . . . 23
BATTERY TEMPERATURE SENSOR
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 23
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 23
GENERATOR
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 24
CHARGING
DESCRIPTION
The charging system consists of:
• Generator
• Generator Decoupler Pulley (if equipped)
• Electronic Voltage Regulator (EVR) circuitry
within the Powertrain Control Module (PCM)
• Ignition switch
• Battery (refer to 8, Battery for information)
• Battery temperature sensor
• Generator Lamp (if equipped)
• Check Gauges Lamp (if equipped)
• Voltmeter (refer to 8, Instrument Cluster for
information)
• Wiring harness and connections (refer to 8, Wir-
ing for information)
OPERATION
The charging system is turned on and off with the
ignition switch. The system is on when the engine is
running and the ASD relay is energized. When the
ASD relay is on, voltage is supplied to the ASD relay
sense circuit at the PCM. This voltage is connected
through the PCM and supplied to one of the genera-
tor field terminals (Gen. Source +) at the back of the
generator.
CHARGING
TABLE OF CONTENTS
page
. . . . . . . . . . . . . . . . . 22
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 24
GENERATOR DECOUPLER PULLEY
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 26
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
DIAGNOSIS AND TESTING - GENERATOR
DECOUPLER . . . . . . . . . . . . . . . . . . . . . . . . . 26
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . 29
VOLTAGE REGULATOR
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 30
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
The amount of DC current produced by the gener-
ator is controlled by the EVR (field control) circuitry
contained within the PCM. This circuitry is con-
nected in series with the second rotor field terminal
and ground.
A battery temperature sensor, located in the bat-
tery tray housing, is used to sense battery tempera-
ture. This temperature data, along with data from
monitored line voltage, is used by the PCM to vary
the battery charging rate. This is done by cycling the
ground path to control the strength of the rotor mag-
netic field. The PCM then compensates and regulates
generator current output accordingly.
All vehicles are equipped with On-Board Diagnos-
tics (OBD). All OBD-sensed systems, including EVR
(field control) circuitry, are monitored by the PCM.
Each monitored circuit is assigned a Diagnostic Trou-
ble Code (DTC). The PCM will store a DTC in elec-
tronic memory for certain failures it detects. Refer to
Diagnostic Trouble Codes in; Powertrain Control
Module; Electronic Control Modules for more DTC
information.
The Check Gauges Lamp (if equipped) monitors:
charging system voltage, engine coolant tempera-
ture and engine oil pressure. If an extreme condition
is indicated, the lamp will be illuminated. This is
done as reminder to check the three gauges. The sig-
nal to activate the lamp is sent via the CCD bus cir-
cuits. The lamp is located on the instrument panel.
Refer to 8, Instrument Cluster for additional infor-
mation.
CHARGING 8F - 21
page