Page 1: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5...
Page 6: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information.
Page 7: Vehicle Modifications / Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Ignition Key Removal ....12 Locking Doors With The Key .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE “Child-Protection” Door Lock System (Rear Doors) ......21 Remote Keyless Entry —...
Page 11 Driver And Front Passenger Supplemental Restraint System (SRS) - Airbag ... .43 Child Restraint ......52 Engine Break-In Recommendations .
Page 12: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place.
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described.
Page 14: Locking Doors With The Key
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector lever.
Page 15 chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle. The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is locked or unlocked.
Page 16: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle.
Page 17: General Information
4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed.
Page 18: Automatic Transaxle Ignition Interlock System
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If you turned the wheel to the right to engage the lock, you must turn the wheel slightly to the right to disengage it. If you turned the wheel to the left to engage the lock, turn the wheel slightly to the left to disengage it.
Page 19: Power Door Locks - If Equipped
WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal inju- ries and death.
Page 20: Central Locking/Unlocking - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Central Locking/Unlocking — If Equipped All vehicle doors and liftgate are locked with the first turn of the key to the LOCK position. The double unlock activation feature requires you to turn the key in the cylinder lock two times within five seconds to UNLOCK all vehicle doors and liftgate at once.
Page 21: Child-Protection" Door Lock System (Rear Doors)
2. Cycle the ignition switch ON/OFF four times ending in the OFF position. 3. Press the interior door lock switch to the LOCK position. 4. A single chime will sound to signify that you have successfully completed the programming. You can turn the feature back on by repeating the above mentioned procedure.
Page 22: Remote Keyless Entry - If Equipped
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), roll down window and open the door with the outside door handle.
Page 23: To Lock The Doors
NOTE: You may turn off this feature and unlock all doors with one press of the button by following the procedure shown in the Central Locking/Unlocking paragraph. To Lock The Doors: Press and release the LOCK button to lock all doors and liftgate.
Page 24: To Program Transmitters
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Program Transmitters Up to four transmitters can be programmed to your vehicle. Your new vehicle was shipped with two trans- mitters. See your dealer for additional transmitters Additional transmitters can be programmed to the sys- tem by using the following procedure: 1.
Page 25: Transmitter Battery Service
Transmitter Battery Service The recommended replacement battery is 2016 or its equivalent. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. With the transmitter buttons facing down, use a thin coin to pry the two halves of the transmitter apart.
Page 26: Security Alarm System - If Equipped
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. To reassemble the transmitter case snap two halves together. Make sure there is an even gap between the two halves. Test transmitter operation. SECURITY ALARM SYSTEM — IF EQUIPPED The system monitors the doors, liftgate, and ignition switch for unauthorized operation.
Page 27: To Disarm The System
To disarm the system: Unlock a front door/liftgate using either the key or the Keyless Entry Transmitter. Starting the vehicle with a valid Sentry key will disarm the system. A valid key is one that is programmed to that particular vehicle. A valid key will disarm the system, an invalid key will trigger the alarm.
Page 28: Liftgate
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE NOTE: The key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate. To unlock the liftgate, insert the key into the lock and turn to the right.
Page 29: Emergency Seat Back Release
WARNING! • Driving with the liftgate open can allow poison- ous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed.
Page 30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a security measure, a Seat Back Emergency Release lever is built into the left side rear seat back latching mechanism. In the event of an individual being locked inside the liftgate area with the rear shelf panel in position 1 (Top) or position 2 (Middle), the left side rear seat back can be unlatched by pulling down on the glow-in-the-dark lever attached to the left rear seat back...
Page 31: Power Windows
NOTE: Make sure that the elastic loop is around the emergency release handle at all times. If the handle is pulled downward, entirely through the elastic loop, the handle will not return to its original position and the seat back may not operate properly. POWER WINDOWS The power window switches are located on the instru- ment panel above the A/C controls.
Page 32: Auto Down Feature
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the win- dows while operating the power window switches. Such entrapment may result in serious injury or death.
Page 33: Wind Buffeting
Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
Page 34: Lap/Shoulder Belts
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street.
Page 35 WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. •...
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is above the back of the front seat, next to your arm. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
Page 37 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.
Page 39 Rear Center Lap/Shoulder Belt Retractor Lock-Out This feature is designed to lock the retractor whenever the rear seat back is not fully latched. This prevents someone from wearing the rear center lap/shoulder belt when the rear seat back is not fully latched. NOTE: •...
Page 40: Adjustable Upper Shoulder Belt Anchorage
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push up or down on the anchorage button to release the anchorage, and move it up or down to the position that serves you best.
Page 41 1. Position the latch plate as close as possible to the anchor point. Positioning Latch Plate THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate.
Page 42: Seat Belt Pretensioners
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. Sliding The Latch Plate 4. Continue to slide the latch plate up until it clears the folded webbing.
Page 43: Seat Belts And Pregnant Women
Seat Belts And Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible.
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. Side Airbags WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them.
Page 45 Airbags inflate in moderate to high speed impacts. Along with seat belts and pretensioners, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. All occupants should wear their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4.
Page 47 The front airbag system consists of the following: • Front Airbag Control Module (ACM) • AIRBAG Readiness Light • Driver and Passenger Front Airbag/Inflator Units • Unique Steering Wheel and Column • Unique Instrument Panel • Interconnecting Wiring • Seat Belt Pretensioners •...
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How The Airbag System Works • The front airbag control module determines if a frontal impact is severe enough to require the airbags to inflate. The front control module will not detect side, roll over, or rear collisions.
Page 49 • When the front airbag control module detects a colli- sion requiring the front airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airbags. The front airbag covers sepa- rate and fold out of the way as the front airbags inflate to their full size.
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs The airbag systems are designed to deploy when the airbag control modules detect a moderate-to-severe col- lision, to help restrain the driver and front passenger, and then immediately deflate. NOTE: A collision that is not severe enough to need airbag protection will not activate the system.
Page 51 WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags and seat belt pretensioners replaced by an autho- rized dealer as soon as possible. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Maintaining Your Airbag System WARNING! •...
Page 52: Child Restraint
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately.
Page 53 WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured.
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. •...
Page 55 WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. •...
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the seat belt has a switchable retractor, it will have a distinctive label. • In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint.
Page 57 Lower Anchors and Tether for CHildren (LATCH) Your vehicle is equipped with the child restraint anchor- age system called LATCH, which stands for Lower Anchors and Tether for CHildren. The LATCH system provides for the installation of the child restraint without using the vehicle seat belt.
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child restraints systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time.
Page 59 Tether Strap Mounting Not all child restraint systems will be installed as we have described here. Again, carefully follow the instruc- tions that come with the child restraint system. NOTE: If your child restraint seat is not LATCH com- patible, install the restraint using the vehicle seat belts. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 WARNING! An incorrectly anchored tether strap could lead to...
Page 60: Engine Break-In Recommendations
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back.
Page 61: Safety Tips
A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill.
Page 62: Periodic Safety Checks You Should Make Outside The Vehicle
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc. If there is any question regarding belt or retractor condition, replace the belt.
Page 63: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......67 Inside Day/Night Mirror ....67 Outside Mirror—Driver’s Side .
Page 64 64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Front Passenger Seat — If Equipped . . .84 Adjustable Head Restraints ....85 Heated Seats — If Equipped ....86 Folding Rear Seat .
Page 65 Electronic Speed Control — If Equipped ..102 To Activate ......102 To Set At A Desired Speed .
Page 66 66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off ..119 Console Features ..... . . 120 Storage .
Page 67: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 68: Outside Mirror-Driver's Side
68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror—Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. Outside Mirror—Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle.
Page 69: Electric Remote-Control Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 Electric Remote-Control Mirrors — If Equipped Use the mirror select switch, located to the left of the steering column on the instrument panel, to adjust the view obtained in the outside mirrors. Press the L or R button for Left or Right mirror selection.
Page 70: Illuminated Vanity Mirrors - If Equipped
NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth Hands-Free Profile, version 0.96 or higher. For UConnect Customer Support call 1-877-855-8400 or visit UConnect website uconnect). (www.chrysler.com/...
Page 71 UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversations. The UConnect™; phone book enables you to store up to 32 names and four numbers per name.
Page 72: Operation
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system can be used with any Hands Free Profile certified Bluetooth™ cellular phone. If your cellular phone has a different profile (i.e. headset profile), you will not be able to use any UConnect™ features. The UConnect™...
Page 73 • You will be asked to say a four-digit pin number into the UConnect™ system which you will later need to enter into your cellular phone during the cellular phone pairing process. You can enter any four-digit pin number. You will not need to remember this pin number after the initial registration process.
Page 74 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt, says Call followed by the name and designation of a phonebook entry that you wish to dial. For example, you can say Call John Doe Work . Add Names to Your UConnect™ Phonebook •...
Page 75 After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu. Phonebook edit can be used to add another phone number to a name entry that already exists in the phonebook.
Page 76: Phone Call Features
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the Ready prompt, say Names . • The UConnect™ system will play the names of all the phonebook entries.
Page 77 Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, press the ’Phone’ button to place the current call on hold and answer the incoming call. To reject the incoming call, you can disregard the call and continue with your current conversation.
Page 78: Advanced Phone Connectivity
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Three-Way Calling To initiate three-way calling, press the ’Voice Recogni- tion’ button while a call is in progress and make a second phone call. When the second call is established, press the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call.
Page 79 • You will be asked to say the name of the phone that you wish to delete. You can either say the name of the phone that you wish to delete or you can say All to delete all the phones. Connect or Disconnect the Connection between the UConnect™...
Page 80: Uconnect™ System Features
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect™ System Features Barge In - Touch Tone Phone Inputs You can use your UConnect™ system to access a voice mail system, an automated service, or any other phone number that you can dial with any phone. When calling a number with your UConnect™...
Page 81 Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g. the UConnect™ sys- tem will not repeat a phone number before you dial it). • Press the ’Phone’ button to begin. • After the Ready prompt, say Setup Confirmation . The UConnect™...
Page 82: Seats
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Help If you need assistance at any prompt or if you want to know what your options are at any prompt, say Help . The UConnect™ system will play all the options at any prompt if you ask for help.
Page 83: Driver's Power Seat Height Adjuster - If Equipped
Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured.
Page 84: Reclining Bucket Seats
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Bucket Seats The recliner control is on the outboard side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position.
Page 85: Adjustable Head Restraints
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the head restraints so that the upper edge is as high as practical.
Page 86: Heated Seats - If Equipped
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped This feature heats the front driver’s and passenger’s seats. The control for the heater is located on the out- board side of each seat. After turning on the ignition, you may choose from HIGH, or LOW heat settings.
Page 87: Folding Rear Seat
Folding Rear Seat To provide additional storage area, each rear seatback can be folded forward. Push and hold the buttons shown in the picture to fold down either or both seatbacks. Folding Rear Seat Button UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 WARNING! •...
Page 88: Tumbling Rear Seat
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the seatback is properly latched and the rear center lap/shoulder belt still does not operate properly check and see if the Automatic Locking retractor (ALR) system is activated. WARNING! The rear center lap/shoulder belt is equipped with a lock-out feature to ensure that the seatback is in the fully upright and locked position when occupied.
Page 89 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 • Push and hold the button on the seatback and fold • Pull the release handle located on the outboard side of down the rear seatback. the seat. Lift up the seat and tumble the seat forward. Folding Rear Seat Button Tumbling Seat Release Handle...
Page 90 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Attach the elastic strap, located at the base of the seat cushion, onto the hook bar on the center trim panel to hold the seat in place. Tumbling Seat Strap To return the rear seat to it’s upright latched position, rotate the seat cushion rearward to latch the seat.
Page 91: Rear Seat Removal
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 • Pull the release lever located on the outboard side of Rear Seat Removal The rear seats can be removed to provide more cargo the seat. Lift up the seat and tumble the seat forward. space.
Page 92 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Lift up the release levers to disengage the seat from the floor attachments. Release Lever Location • Using the handle on the seat, the seat assembly can now be lifted and removed from the vehicle. NOTE: Small rollers on the bottom of the folded seat and a handle at the top allow the seat to be easily moved when removed from the vehicle.
Page 93: To Open And Close The Hood
TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Hood Release Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Then move the safety catch located under the front edge of the hood, near the center and slightly to the right, and raise the hood.
Page 94: Lights
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS Overhead Console Map/Reading Lights —...
Page 95: Interior Lights
Interior Lights The interior lights come on when a door is opened. With the ignition key in the OFF position, the interior lights will automatically turn off in about 8 minutes if a door is left open or the dimmer control is left in the Dome light position.
Page 96: Multi-Function Control Lever
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior light Defeat (OFF) Rotate the dimmer control to the ex- treme bottom “OFF” position. The in- terior lights will remain off when the doors are open. Parade Mode (Daytime Brightness Feature) Rotate the dimmer control to the first detent (white semi-circle).
Page 97: Daytime Running Lights (Canada Only)
Multi-Function Control Lever To change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Control Lever up or down. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Daytime Running Lights (Canada Only) The front turn signal lights will come on as Daytime Running Lights whenever the ignition switch is on, the headlights are off, and the parking brake is off.
Page 98: Turn Signals
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The fog lights will only operate with the head- lights on low beam. Selecting high beam headlights will turn off the fog lights. Turn Signals Move the Multi-Function Control Lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.
Page 99: Windshield Washers
Windshield Wiper/Washer Control Windshield Washers To use the washer, pull the control lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate in low speed for two wipe cycles after the lever is released, and then resume the intermittent interval previously selected.
Page 100: Windshield Wiper Operation
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Operation Move the lever upward to the second detent for Low speed wiper operation, or to the third detent for High speed operation Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable.
Page 101: Traction Control Switch - If Equipped
WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving. TRACTION CONTROL SWITCH —...
Page 102: Electronic Speed Control - If Equipped
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Traction Control System indicator “TRAC OFF” will illuminate momentarily as a bulb check, each time the ignition switch is turned ON. This will occur even if you used the “TRAC OFF” switch to turn the system OFF.
Page 103: To Set At A Desired Speed
WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it. To Set At A Desired Speed: When the vehicle has reached the desired speed, press down on the lever and release.
Page 104: Manual Transaxle
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tapping “ACC/RES” once will result in a 2 mph (3 km/h) speed increase. Each time the lever is tapped, speed increases so that tapping the lever three times will increase speed by 6 mph (10 km/h), etc. To decrease speed while speed control is ON, push down and hold “COAST/SET”.
Page 105: Garage Door Opener - If Equipped
Vehicles equipped with four speed automatic transaxles may experience a downshift to 3rd gear while climbing uphill or descending downhill. This downshift to 3rd gear is necessary to maintain vehicle set speed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control.
Page 106: Programming The Universal Transceiver
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse”...
Page 107 WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects.
Page 108: Rolling Code" Programming
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. The indicator light in the Universal Transceiver will begin to flash, first slowly and then rapidly. The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and repeat the procedure.
Page 109: Canadian Programming/Gate Programming
NOTE: The assistance of a second person may make the following programming procedure quicker and easier. 1. Locate the training button on the garage door motor head unit. The exact location and color of the button may vary by garage door opener manufacturer. If you have difficulty in locating the training button, check your garage door opener manual, or call 1-800-355-3515 or, on the Internet, at www.homelink.com.
Page 110: Operation
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Universal Transceiver light will flash slowly and then rapidly when the programming is successful. NOTE: When programming such a garage door opener or gate, unplug the device to prevent possible damage to the garage door or gate motor.
Page 111: Overhead Console - If Equipped
This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation.
Page 112: Compass/Temperature Display
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass/Temperature Display This display provides the outside temperature and one of eight compass readings to indicate the direction the vehicle is facing. WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges.
Page 113: Automatic Compass Calibration
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Automatic Compass Calibration The automatic calibrating feature of the compass elimi- nates the need to calibrate the compass due to normal varying conditions. Compass Variance Selection Variance is the difference between magnetic North and geographic North.
Page 114: Manual Compass Calibration
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Compass Calibration If the compass appears erratic, inaccurate, abnormal or the vehicle is new, you may calibrate the compass. Prior to calibrating the compass make sure the proper zone is selected. Refer to “Magnetic Zone Selection”.Find an open area away from large metal objects.
Page 115: Express Open Feature
Power Sunroof Switch Press and hold the switch rearward to fully open the sunroof. The sunroof can be stopped at any position between closed and full open. Momentarily pressing the switch rearward will activate the Express Open Feature, causing the sunroof to open automatically. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Press and hold the button in the center of the sunroof switch to open the vent.
Page 116 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The sunshade can be opened manually. It will also open as the sunroof opens. The sunshade cannot be closed if the sunroof is open. WARNING! Never leave children in a vehicle, with the keys in the ignition switch.
Page 117: Wind Buffeting
Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
Page 118 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE It will accept a cigar lighter unit, which is part of the optional Smokers Package. To preserve the heating ele- ment of the cigar lighter unit, do not hold the lighter in the heating position. As a child safety precaution, this outlet is powered by the ignition switch, only when the switch is in the ON or ACCESSORY positions.
Page 119: Electrical Outlet Use With Engine Off
The second is in the right rear cargo area. Rear Power Outlet Since this outlet is remote from the driver, it is powered by the ignition switch, only when it is in the ON or ACCESSORY positions, to protect the battery against discharge.
Page 120: Console Features
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES The console has two front cup holders, a coin holder, 12 volt power outlet and a front storage tray. There are additional cup holders; one is molded in the center of the console to hold large cups and the other is at the rear of the console to serve passengers in the rear seat.
Page 121: Storage
CAUTION! • Many accessories that can be plugged into the 12 volt power outlet, draw power from the vehicle’s battery, even when not in use; i.e. cellular phones, etc. Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine start- ing.
Page 122: Storage Pockets
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage Pockets There are also Storage pockets located on each door trim panel. REAR SHELF PANEL The rear shelf panel attaches to guides in the rear cargo area. The rear shelf panel may be installed in one of five different positions.
Page 123: Position 2 (Middle)
Rear Shelf Panel Position 1 WARNING! Do not load objects on the shelf in position 1 (top). In an accident objects could strike occupants causing serious or fatal injury. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Position 2 (Middle) Insert the front outboard corners of the shelf panel into the middle guides and slide forward.
Page 124: Position 3 (Floor)
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not load objects over 100 lbs (45 kg) in position 2 (middle). Failure to follow this warning could cause the shelf to collapse resulting in personal injury. Position 3 (Floor) Insert the front outboard corners of the shelf panel into the bottom guides and slide forward.
Page 125: Position 5 (Table)
WARNING! When in the vertical position, the rear shelf panel should not be used as a barrier for large objects in the cargo area when the seatbacks folded down. In an accident objects could strike the seatbacks or occupants causing serious or fatal injury. Position 5 (table) With the liftgate open the rear shelf panel can be moved rearward to act as a serving counter.
Page 126: Roof Luggage Rack - If Equipped
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Install the shelf leg into the liftgate latch area as labeled on the rear scuff plate. Rear Shelf Panel Position 5 WARNING! Do not load objects over 100 lbs (45 kg) in position 5 (table).
Page 127 To adjust the crossbars with botton style releases, depress the button and slide the crossbar to the next locking position. Alternate sides until the crossbars are posi- tioned correctly for your cargo and the stanchions are locked square to the slide rails. External racks do not increase the total load carrying capacity of the vehicle.
Page 128 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack “Cautions” when carrying cargo on your roof rack.
Page 129: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....133 Instrument Cluster ..... . 134 Instrument Cluster—Turbo, With AutoStick .
Page 130 130 UNDERSTANDING YOUR INSTRUMENT PANEL Cassette Player Features ....149 CD Changer Control Capability — If Equipped ..... . . 150 Sales Code RAZ—AM/ FM Stereo Radio With Cassette Tape Player, CD Player And CD Changer Controls .
Page 131 Pinch Roller Release ....158 Noise Reduction ..... . 158 Operating Instructions —...
Page 132 132 UNDERSTANDING YOUR INSTRUMENT PANEL Satellite Radio — If Equipped ....177 System Activation ..... 178 Electronic Serial Number/Sirius Identification Number (ENS/SID) .
Page 133: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 133 INSTRUMENT PANEL FEATURES...
Page 134: Instrument Cluster
134 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER...
Page 135: Instrument Cluster-Turbo, With Autostick
UNDERSTANDING YOUR INSTRUMENT PANEL 135 INSTRUMENT CLUSTER—TURBO, WITH AUTOSTICK...
Page 136: Instrument Cluster-Turbo, Without Autostick
136 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER—TURBO, WITHOUT AUTOSTICK...
Page 137: Instrument Cluster Descriptions
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Charging System Light This light shows the status of the electrical charg- ing system.
Page 138 138 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Engine Temperature Warning Light This light warns of an overheated engine condi- tion. If the engine is critically hot, a warning chime will sound 10 times. After the chime turns off, the engine will still be critically hot until the light goes out. 7.
Page 139 10. High Beam Indicator This light shows that the headlights are on high beam. Pull the turn signal lever toward the steer- ing wheel to switch the headlights from high or low beam. 11. Tachometer The white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range.
Page 140 140 UNDERSTANDING YOUR INSTRUMENT PANEL 14. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light comes on, it may indicate that the parking brake is applied, or there is a low brake fluid level.
Page 141 The light will flash when the Traction Control System is controlling traction. 16. Door Ajar Indicator This vacuum fluorescent display indicator illuminates the word “DOOR”, when a door is not completely closed. If the door is open for more than 8 minutes, the light will turn off.
Page 142 142 UNDERSTANDING YOUR INSTRUMENT PANEL 20. Airbag Light The light comes on and remains on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the light does not come on during starting, stays on, or comes on while driving, have the system checked by an authorized dealer.
Page 143 Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations the vehicle will drive normally and will not require towing.
Page 144: Electronic Digital Clock
144 UNDERSTANDING YOUR INSTRUMENT PANEL 27. Odometer/Trip Odometer Reset Knob Press the knob to switch between the odometer and trip odometer. While the trip odometer is being displayed, press and hold this knob for a few seconds to reset the trip odometer to zero miles/kilometers.
Page 145: Two Types Of Signals
you understand and save you concern about these “ap- parent” malfunctions, you must understand a point or two about the transmission and reception of radio sig- nals. Two Types of Signals There are two basic types of radio signals... AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary...
Page 146: Sales Code Rbb-Am/Fm Stereo Radio With Cassette Tape Player And Cd Changer Capability
146 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RBB—AM/FM STEREO RADIO WITH CASSETTE TAPE PLAYER AND CD CHANGER CAPABILITY RBB Radio Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch.
Page 147 Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection.
Page 148: Mode Button
148 UNDERSTANDING YOUR INSTRUMENT PANEL Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to increase or decrease the Bass tones. Press the AUDIO button a second time and TREB will be displayed. Press the SEEK + or SEEK – to increase or decrease the Treble tones.
Page 149: Cassette Player Features
Cassette Player Features With ignition OFF and the sound system OFF, you can eject the tape cassette by pushing the EJECT button. You can turn the tape player ON by inserting a cassette or activating the MODE button (with a cassette in the radio), but only when the ignition and radio are on.
Page 150: Cd Changer Control Capability - If Equipped
150 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Cassette Mode) Pressing this button while playing a cassette tape will change the side of the tape being played. NR (Noise Reduction) Pushing the Number 2 Pre-set button when a tape is playing deactivates the Dolby Noise Reduction System*. When Dolby is ON, the NR symbol appears on the display.
Page 151 Fast Forward And Rewind Buttons Press and hold the FF button for fast forward. Press and hold the RW button for fast reverse. The audio output can be heard when fast forward and fast reverse are activated. Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace.
Page 152: Sales Code Raz-Am/ Fm Stereo Radio With Cassette Tape Player, Cd Player And Cd Changer Controls
152 UNDERSTANDING YOUR INSTRUMENT PANEL An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: • Excessive vibration • Disc inserted upside down • Damaged disc • Water condensation on optics SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS...
Page 153: Power Switch, Volume Control
Power Switch, Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. The volume will be displayed and continuously updated while the button is pressed. Seek Button (Radio Mode) Press and release the Seek button to search for the next station in either the AM or FM mode.
Page 154: Pty (Program Type) Button
154 UNDERSTANDING YOUR INSTRUMENT PANEL PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off. Pressing the PTY button within 5 seconds will allow the program format type to be selected.
Page 155: Balance
By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station.
Page 156: Am/Fm Selection
156 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received. Scan Button Pressing the SCAN button causes the tuner to search for the next station, in either AM or FM, pausing for 5 seconds at each listenable station before continuing to the...
Page 157: To Change From Clock To Radio Mode
To Change From Clock To Radio Mode Press the Time button to change the display between radio frequency and time. Operating Instructions — Tape Player Insert the cassette with the exposed tape side toward the right and the mechanical action of the player will gently pull the cassette into the play position.
Page 158: Tape Eject
158 UNDERSTANDING YOUR INSTRUMENT PANEL Tape Eject Press the EJT Tape button and the cassette will disengage and eject from the radio. Scan Button Press this button to play 10 seconds of each selection. Press the scan button a second time to cancel the feature. Changing Tape Direction If you wish to change the direction of tape travel (side being played), press the PTY button.
Page 159: Operating Instructions - Cd Player
Operating Instructions — CD Player NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. CAUTION! This CD player will accept 4 ⁄ inch (12 cm) discs only.
Page 160: Seek Button
160 UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection.
Page 161: Mode
MODE Press the MODE button to select between the tape player, CD player, or satellite radio (if equipped). To select Satellite Radio (if equipped), press the MODE button until the word SIRIUS appears. The following will be displayed in this order: After three seconds, the current channel name and number will be displayed for five seconds.
Page 162 162 UNDERSTANDING YOUR INSTRUMENT PANEL Disc Down/Program Button 5 Press the DISC down (button 5) button to play the previous disc. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. Fast Forward And Rewind Buttons Press and hold the FF button for fast forward.
Page 163: Sales Code Rbk-Am/ Fm Stereo Radio With Cd Player And Cd Changer Controls
SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS RBK Radio UNDERSTANDING YOUR INSTRUMENT PANEL 163 Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch.
Page 164 164 UNDERSTANDING YOUR INSTRUMENT PANEL the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button.
Page 165: Cd Player Operation
Press the AUDIO button a fourth time and FADE will be displayed. Press the SEEK + or SEEK – to adjust the sound level between the front and rear speakers. Press the AUDIO button again or wait 5 seconds to exit setting tone, balance, and fade.
Page 166 166 UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc CAUTION! This CD player will accept 4 only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day.
Page 167: Cd Changer Control Capability - If Equipped
FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play.
Page 168 168 UNDERSTANDING YOUR INSTRUMENT PANEL Disc Up/Program Button 1 Press the DISC up (button 1) button to play the next available disc. Disc Down/Program Button 5 Press the DISC down (button 5) button to play the previous disc. Seek Button Press the SEEK up or down to select another track on the same disc.
Page 169: Sales Code Rbq-Am/Fm Stereo Radio With 6 - Disc Cd Changer
A CD HOT symbol indicates the player is too hot. CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected. An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: •...
Page 170: Radio Operation
170 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation Power/Volume Control Press the PWR/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio.
Page 171 To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET RND button. SET 1 will show in the display window. Select the “1–6” button you wish to lock onto this station and press and release that button.
Page 172: Cd Player Operation
172 UNDERSTANDING YOUR INSTRUMENT PANEL Time Button Press the TIME button to change the display between radio frequency and time. General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1.
Page 173 If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the disc number, the track number, and index time in minutes and seconds.
Page 174 174 UNDERSTANDING YOUR INSTRUMENT PANEL Scan Press the Scan button to scan through each track on the CD currently playing. FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner.
Page 175 Program Type Radio Display Information Inform Jazz Jazz Foreign Language Language News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious Talk Rel Talk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B...
Page 176 176 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SCAN button when the PTY icon is displayed, the radio will stop at every PTY station on the band and list each corresponding program type in the radio display. Time Press the TIME button to change the display from elapsed CD playing time to time of day.
Page 177: Sales Code Rb1-Am/Fm Stereo Radio With Dvd/Gps Navigation System
SALES CODE RB1—AM/FM STEREO RADIO WITH DVD/GPS NAVIGATION SYSTEM RB1 Radio The navigation system provides maps, turn identifica- tion, selection menus and instructions for selecting a UNDERSTANDING YOUR INSTRUMENT PANEL 177 variety of destinations and routes. Refer to your “Navi- gation User’s Manual”...
Page 178: System Activation
178 UNDERSTANDING YOUR INSTRUMENT PANEL System Activation To activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com. Please have the following informa- tion available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID).
Page 179: Selecting Satellite Mode In Rbb, Rah And Rbk Radios
mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. Selecting Satellite Mode in RBB, RAH and RBK Radios Press the MODE button repeatedly until S A appears in the display.
Page 180: Storing And Selecting Pre-Set Channels
180 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Channels that may contain objectionable content can be blocked. Contact Sirius Customer Care at 888-539- 7474 to discuss options for channel blocking or unblock- ing. Please have your ESN/SID information available. Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory.
Page 181: Satellite Antenna
Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items should be placed as far forward as possible. Do not place items directly on or above the antenna.
Page 182: Cd/Dvd Disc Maintenance
182 UNDERSTANDING YOUR INSTRUMENT PANEL 5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the required directions. Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
Page 183: Radio Operation And Cellular Phones
RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
Page 184 184 UNDERSTANDING YOUR INSTRUMENT PANEL The controls are as follows: Fan and Air conditioning Control Use this control to regulate the amount of air forced through the system in any mode you select. The fan speeds to the left of the OFF position are for Air Condi- tioning.
Page 185 Bi-Level Air is directed through the panel and floor outlets. NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Floor Air is directed through the floor outlets and side window demist outlets with a small amount...
Page 186 186 UNDERSTANDING YOUR INSTRUMENT PANEL on the outer edge of each instrument panel outlet grille opens or closes a shutter to turn airflow on or off through that outlet. NOTE: For maximum airflow to the rear seat passen- gers, the center instrument panel outlets can be aimed, so that the left center outlet is directed toward the right rear passenger and the right center outlet is directed toward the left rear passenger.
Page 187 This control only operates in the Outside Air and Recir- culate modes; there is no in between position. Do not place the control between these positions. NOTE: Continuous use of the recirculate mode may make the inside air stuffy and window fogging may occur.
Page 188: Operating Tips
188 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips...
Page 189 Window Fogging Vehicle side windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, use the A/C, PANEL and blower controls. Direct the panel outlets toward the side windows. Do not use recirculate without A/C for long periods as fogging may occur.
Page 190: Rear Window Features
190 UNDERSTANDING YOUR INSTRUMENT PANEL Side Window Demisters A side window demister outlet is at each end of the instrument panel. These nonadjustable outlets direct air toward the side windows when the system is in either the FLOOR, MIX, or DEFROST mode. The air is directed at the area of the windows through which you view the outside mirrors.
Page 191: Rear Wiper/Washer Switch
CAUTION! To avoid damaging the electrical conductors, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the rear window. Labels can be peeled off after soaking with warm water. Rear Wiper/Washer Switch A push-button at the center of the instrument panel, below the radio, turns the rear wiper ON or OFF.
Page 192: Adding Washer Fluid
192 UNDERSTANDING YOUR INSTRUMENT PANEL Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the rear of the engine compartment on the passenger side and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radia- tor antifreeze) and operate the system for a few seconds to flush out the residual water.
Page 193: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 196 Automatic Transaxle ....196 Manual Transaxle .
Page 194 194 STARTING AND OPERATING AutoStick General Information ... . 204 Manual Transaxle Operation ....205 2.4 Liter Turbo— If Equipped ... . . 207 Recommended Shift Speeds .
Page 195 Snow Tires ......233 Tire Rotation Recommendations ... . 234 Fuel Requirements .
Page 196: Starting Procedures
196 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle.
Page 197: Extremely Cold Weather (Below 20°F Or 29°C)
started within 3 seconds, slightly depress the accelerator pedal while continuing to crank. If the engine fails to start within 15 seconds, turn the ignition switch to the “OFF” position, wait 10 to 15 seconds, then repeat the normal starting procedure. WARNING! Do not attempt to push or tow your vehicle to get it started.
Page 198: After Starting
198 STARTING AND OPERATING WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time.
Page 199: Automatic Transaxle - If Equipped
TURBOCHARGER COOL DOWN CHART Driving Conditions Normal Driving Aggressive Driving or Heavily Loaded Trailer Tow AUTOMATIC TRANSAXLE — IF EQUIPPED CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop.
Page 200: Brake/Transmission Interlock System
200 STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse.
Page 201: Reset Mode
Reset Mode The transaxle is monitored electronically for abnormal conditions. If a condition is detected that could cause damage, the transaxle shifts automatically into second gear. The transaxle remains in second gear despite the forward gear selected. Park (P), Reverse (R), and Neutral (N) will continue to operate.
Page 202 202 STARTING AND OPERATING WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into P (Park), remove the key from the ignition, and apply the parking brake.
Page 203 “R” Reverse Shift into this range only after the vehicle has come to a complete stop. “N” Neutral Engine may be started in this range. “D” Overdrive This range should be used for most city and highway driving. It provides smoothest up shifts and down shifts and best fuel economy.
Page 204: Autostick - If Equipped
204 STARTING AND OPERATING AUTOSTICK — IF EQUIPPED Autostick is a driver-interactive transmission that offers manual gear shifting capability to provide you with more control. Autostick allows you to maximize engine brak- ing, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations.
Page 205: Manual Transaxle Operation
• Downshifts from third to second gear above 74 mph (119 km/h) and from second to first gear above 41 mph (66 km/h) will be ignored. • You can start out in first, second, or third gear. Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h).
Page 206 206 STARTING AND OPERATING Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelera- tor pedal. Use each gear in numerical order - do not skip a gear. Be sure the transaxle is in FIRST gear, (not THIRD), when starting from a standing position.
Page 207: 2.4 Liter Turbo- If Equipped
2.4 Liter Turbo— If Equipped The neutral position of the shift lever is located between THIRD and FOURTH gear. This is the position the shifter lever will return to automatically when neutral is se- lected. When shifting into FIFTH gear, be sure to press STARTING AND OPERATING 207 the shifter lever all the way to the right to avoid acciden- tally selecting THIRD gear.
Page 208: Downshifting
208 STARTING AND OPERATING TABLE 1-MANUAL TRANSAXLE NORMAL AC- CELERATION AND CRUISE SHIFT SPEEDS IN mph (km/h) GINE MODE 1 to 2 2 to 3 SIZE Accel 15 (24) 25 (40) 2.4L Turbo Cruise 15 (24) 25 (40) 2.4L Accel 15 (24) 25 (40) Non- Cruise...
Page 209: Parking Brake
CAUTION! If you skip more than one gear while downshifting or downshift at too high an engine speed, you could damage the engine, transmission, or clutch. To maintain a safe speed and prolong brake life, shift down to 2nd or 1st when descending a steep grade. When turning a corner, or driving up a steep grade, downshift early so that the engine will not be overbur- dened.
Page 210 210 STARTING AND OPERATING NOTE: The parking brake lever will not release unless the lever is pulled up slightly past its applied position. Parking Brake Lever When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the automatic transaxle locking mechanism may make it difficult to move the selector out of Park.
Page 211: Brake System
WARNING! • Leaving children in a vehicle unattended is dan- gerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle.
Page 212: Anti-Lock Brake System (Abs) If Equipped
212 STARTING AND OPERATING If either of the two hydraulic systems lose normal capa- bility, the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop.
Page 213: Power Assisted Steering
WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. •...
Page 214: Traction Control - If Equipped
214 STARTING AND OPERATING TRACTION CONTROL — IF EQUIPPED The Traction Control System will improve acceleration and steering on slippery surfaces by reducing tire spin. The system reduces wheel slip and maintains traction at the driving (front) wheels by engaging the brake on the wheel that is losing traction.
Page 215 The system is always in the “ON” mode unless: • The TRAC OFF switch has been used to turn the system off; • There is a Anti-Lock Brake System malfunction; • There is a Traction Control System malfunction; • The system has been automatically deactivated to prevent damage to the brake system due to overheated brake temperatures.
Page 216: Tire Safety Information
216 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards.
Page 217 Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%)
Page 218 218 STARTING AND OPERATING Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 219: Tire Identification Number (Tin)
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. DOT = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S.
Page 220: Tire Loading And Tire Pressure
220 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure for pas- senger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the “B”...
Page 221 Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle STARTING AND OPERATING 221 4) the cold tire inflation pressures for the front, rear and spare tires.
Page 222 222 STARTING AND OPERATING lbs.” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occu- pants and cargo should never exceed XXX pounds”...
Page 223 STARTING AND OPERATING 223...
Page 224: Tires-General Information
224 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 225: Tire Inflation Pressures
2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3.
Page 226 226 STARTING AND OPERATING The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation.
Page 227 Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits.
Page 228: Radial-Ply Tires
228 STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels).
Page 229: Limited Use Spare - If Equipped
Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the...
Page 230: Tire Spinning
230 STARTING AND OPERATING WARNING! The limited use spare tires are for emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly.
Page 231: Tread Wear Indicators
Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm).
Page 232: Alignment And Balance
232 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspen- sion dimensions and performance characteristics, resulting in changes to steering, handling, and brak- ing of your vehicle.
Page 233: Tire Chains
Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE CHAINS Due to limited clearance, tire chains are not recom- mended.
Page 234: Tire Rotation Recommendations
234 STARTING AND OPERATING Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear pat- terns.
Page 235: Fuel Requirements
FUEL REQUIREMENTS 2.4L Standard Engine and 2.4L Standard Turbo Engine Your vehicle is designed to meet all emis- sion regulations and provide excellent fuel economy when using high quality regular unleaded gasoline with an octane rating of 87. The use of premium gasoline is not recommended.
Page 236: Reformulated Gasoline
236 STARTING AND OPERATING Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
Page 237: Mmt In Gasoline
MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane num- ber. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT have shown to reduce spark plug life and reduce emission system performance in some vehicles.
Page 238: Carbon Monoxide Warnings
238 STARTING AND OPERATING • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service.
Page 239: Adding Fuel
• Guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous ex- haust gases from entering the vehicle.
Page 240 240 STARTING AND OPERATING CAUTION! A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on. CAUTION! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
Page 241: Vehicle Loading
WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. VEHICLE LOADING Vehicle Loading Capacities Front Seat Occupants ..... . . 2 Rear Seat Occupants .
Page 242: Warranty
242 STARTING AND OPERATING Warranty To maintain warranty coverage, follow the requirements and recommendations in this manual concerning ve- hicles used for trailer towing. However the following conditions must be met: • The maximum frontal area of the trailer cannot exceed 20 square feet (1.86 square meters).
Page 243 • Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are recommended for motoring safety. • The automatic transaxle fluid and filter should be changed if you REGULARLY tow a trailer for more than 45 minutes of continuous operation.
Page 245: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....246 If Your Engine Overheats ....246 Jacking And Tire Changing .
Page 246: Hazard Warning Flasher
246 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER Hazard Flasher Switch The flasher switch is on top of the steering column, just behind the steering wheel. Depress the switch and both cluster indicators and all front and rear direc- tional signals will flash.
Page 247 If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. Pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the H (red) mark, turn the engine off immediately and call for service.
Page 248: Jacking And Tire Changing
248 WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to Section 7, Maintenance, of this manual.
Page 249: Jack Location
Jack Location The jack and jack-handle are stowed behind the right rear side trim panel in the cargo area. Jack Location Do not attempt to raise this vehicle using a bumper jack. WHAT TO DO IN EMERGENCIES 249 Spare Tire Stowage The compact spare tire is stowed under the rear of the vehicle by means of a hook/basket mechanism.
Page 250: Preparations For Jacking
250 WHAT TO DO IN EMERGENCIES Spare Tire Removal Lift up the cover and fit the jack-handle over the drive nut. Rotate the nut to the left until you can remove the swivel hook from the stowage basket. Swing the basket down to remove the compact spare tire.
Page 251: Jacking Instructions
Jacking Instructions 1. Remove the scissors jack and lug wrench from the stowage bag. NOTE: If equipped with a center cap that covers the wheel nuts, pry off the cap using the small end of the lug wrench. To reinstall the cap, make sure it is properly lined up before pushing it on to the wheel.
Page 252 252 WHAT TO DO IN EMERGENCIES Do not raise the vehicle until you are sure the jack is securely engaged. 4. Raise the vehicle by turning the jack screw to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire.
Page 253 6. Lower the vehicle by turning the jack screw to the left. 7. Finish tightening the nuts. Push down on the wrench while tightening the wheel nuts. Alternate nuts until each nut has been tightened twice. Correct wheel nut torque is 100 ft.
Page 254: Jump-Starting Procedures Due To A Low Battery
254 WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES DUE TO A LOW BATTERY WARNING! Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be hurt by the fan. WARNING! Do not attempt to push or tow your vehicle to get it started.
Page 255 2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach but without letting the vehicles touch. Set parking brake, place auto- matic transaxle in PARK (manual transaxle in NEU- TRAL) and turn ignition to OFF for both vehicles. 3.
Page 256: Driving On Slippery Surfaces
256 WHAT TO DO IN EMERGENCIES 5. Connect the other cable, first to the negative terminal of the booster battery and then to the negative jump start terminal, located near the hood release latch, of the vehicle with the discharged battery. Make sure you have a good contact.
Page 257: Traction
WARNING! Rapid acceleration on slippery surfaces is danger- ous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet, mud, loose sand, etc.).
Page 258: Towing A Disabled Vehicle
258 WHAT TO DO IN EMERGENCIES If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between Reverse and First gear.
Page 259: Without The Ignition Key
Manual Transaxle Your vehicle may be towed if the gearshift lever is in NEUTRAL. If the transaxle is not operative, the vehicle must be towed with the front wheels off the ground. All Transaxles CAUTION! If the vehicle being towed requires steering, the ignition switch must be in the OFF position, not in the LOCK or ACCESSORY positions.
Page 261: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS 2.4L Turbo Engine Compartment ... . 264 2.4L Engine Compartment ....265 Onboard Diagnostic System —...
Page 262 262 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance ... . . 279 Power Steering — Fluid Check ... . 280 Front Suspension Ball Joints ....280 Body Lubrication .
Page 263 Center High Mounted Stop Light ..310 Fluids And Capacities ....311 Recommended Fluids, Lubricants And Genuine Parts .
Page 264: 2.4L Turbo Engine Compartment
264 MAINTAINING YOUR VEHICLE 2.4L TURBO ENGINE COMPARTMENT...
Page 265: 2.4L Engine Compartment
MAINTAINING YOUR VEHICLE 265 2.4L ENGINE COMPARTMENT...
Page 266: Onboard Diagnostic System - Obd Ii
266 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 267: Emissions Inspection And Maintenance Programs
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready...
Page 268: Replacement Parts
268 MAINTAINING YOUR VEHICLE a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station.
Page 269: Maintenance Procedures
NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 270 270 MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. Engine Oil Dipstick Checking the oil while the vehicle is on level ground, will improve the accuracy of the oil level readings.
Page 271 • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). • Trailer towing. •...
Page 272 272 MAINTAINING YOUR VEHICLE Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API certified and meet the requirements of DaimlerChrysler Material Standard MS-6395. American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American...
Page 273: Drive Belts - Check Condition And Tension
Materials Added To Engine Oils The manufacture strongly recommends against the addi- tion of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental ad- ditives.
Page 274: Spark Plugs
274 MAINTAINING YOUR VEHICLE Special tools are required to properly measure tension and to restore belt tension to factory specifications. Also, check belt routing to make sure there is no interference between the belts and other engine components. Spark Plugs Spark plugs must fire properly to assure engine perfor- mance and emission control.
Page 275 CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the...
Page 276: Engine Timing Belt
276 MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle.
Page 277: Maintenance-Free Battery
For vehicles with a Turbo engine, a small NOTE: amount of oil accumulation in the air cleaner box is normal. The amount will depend on driving style. The air cleaner box should be cleaned out and a new make-up- air filter element should be installed during the normal air filter maintenance procedure.
Page 278 278 MAINTAINING YOUR VEHICLE WARNING! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water.
Page 279: Air Conditioner Maintenance
Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time.
Page 280: Power Steering - Fluid Check
280 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
Page 281: Body Lubrication
Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors,liftgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the appli- cation of any lubricant, the parts concerned should be wiped clean to remove dust and grit;...
Page 282: Windshield Washer Reservoir
282 MAINTAINING YOUR VEHICLE 2. Push the release tab shown in the illustration and slide the wiper blade assembly down along the arm. Gently place the wiper arm on the windshield. 3. Install the new blade assembly onto the wiper arm tip until it locks in place.
Page 283: Exhaust System
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system, or if exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged;...
Page 284: Cooling System
284 MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position.
Page 285 Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner.
Page 286 286 MAINTAINING YOUR VEHICLE Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Years or 100,000 miles before replacement. To prevent reducing this extended mainte- nance period, it is important that you use the same coolant throughout the life of your vehicle.
Page 287 WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
Page 288 288 MAINTAINING YOUR VEHICLE When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
Page 289: Hoses And Vacuum/Vapor Harnesses
• Do not change the thermostat for summer or winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions. Hoses And Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage.
Page 290: Brake System
290 MAINTAINING YOUR VEHICLE Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Suggested service intervals can be found in the Mainte- nance Section. WARNING! Riding the brakes can lead to brake failure and possibly an accident.
Page 291 NOTE: Often, fluids such as oil, power steering fluid, and brake fluid are used during assembly plant opera- tions to ease the assembly of hoses to couplings. There- fore, oil wetness at the hose-coupling area is not neces- sarily an indication of leakage. Actual dripping of hot fluid when systems are under pressure (during vehicle operation) should be noted before a hose is replaced based on leakage.
Page 292 292 MAINTAINING YOUR VEHICLE NOTE: If your vehicle is equipped with a manual transaxle, the Brake Fluid Reservoir supplies fluid to both the Brake System and the Clutch Release System. The two systems are separated in the reservoir and a leak in one system will not affect the other system.
Page 293: Automatic Transaxle
WARNING! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard pro- longed braking. You could have an accident. WARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire.
Page 294 294 MAINTAINING YOUR VEHICLE CAUTION! Using a transmission fluid other than the manufac- turers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes.
Page 295 Transaxle Dipstick Location 6. Wipe the dipstick clean and reinsert until seated. Remove dipstick and note reading. If the fluid is hot, reading should be in the cross hatched area marked “HOT” between the upper two holes in the dipstick. MAINTAINING YOUR VEHICLE 295 If the fluid is cold, the fluid level should be between the lower two holes, into the area marked “LOW”.
Page 296: Manual Transaxle
296 MAINTAINING YOUR VEHICLE Maintenance schedule “A”—Non Turbo Charged En- gines – No change necessary. Maintenance schedule “A”—Turbo Charged Engines – No change necessary. Maintenance schedule “B”—All Engines – Every 60,000 miles (96 000 km) change fluid and filter under the following conditions: •...
Page 297: Appearance Care And Protection From Corrosion
Frequency Of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the following conditions exist: • The lubricant has become contaminated with water. If contaminated with water, the fluid should be changed immediately.
Page 298 298 MAINTAINING YOUR VEHICLE • Atmospheric fallout/industrial pollutants. Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumu- lated on your vehicle, wash it as soon as possible.
Page 299 • Use Mopar touch up paint on scratches or chips as soon as possible. Your dealer has touch up paint to match the color of your vehicle. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible.
Page 300 300 MAINTAINING YOUR VEHICLE When cleaning extremely dirty wheels, care must be taken in the selection of tire and wheel cleaning chemi- cals and equipment to prevent damage to the wheels. Only Mopar Wheel Cleaners are recommended. DO NOT USE any of the items listed below which can damage your wheels and wheel trim.
Page 301 Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar Total Clean.
Page 302 302 MAINTAINING YOUR VEHICLE Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters. Do not use scrapers or other sharp instru- ments which may scratch the elements.
Page 303: Fuses
FUSES Underhood Fuses (Power Distribution Center) A Power Distribution Center is located in the engine compartment; next to the air cleaner filter. A label iden- tifying the components and circuits is located on the underside of the cover. Power Distribution Center Location MAINTAINING YOUR VEHICLE 303 MAXI Amp/Color...
Page 304: Interior Fuses
304 MAINTAINING YOUR VEHICLE MINI Amp/Color FUSE 10 Amp/Red Air Conditioning (A/C) 15 Amp/Blue Stop Lights 20 Amp/ Fuel Pump/Auto Shut Yellow Down (ASD) 15 Amp/Blue Horn 20 Amp/ Electronic Automatic Yellow Transaxle (ETAX) 15 Amp/Blue Hi Beam 20 Amp/ Yellow 15 Amp/Blue Hazard Flasher...
Page 305 FUSE Amp/Color Items Fused 25 Amp/ Headlamp Switch Natural 15 Amp/Blue Exterior Lighting 20 Amp/ RKE/Door Locks Yellow 20 Amp/ Power Height Adjust Yellow 10 Amp/Red Airbag Run Only 10 Amp/Red B/U Electric Back Light (EBL) NEU SAF 25 Amp/ HVAC Blower Natural 15 Amp/Blue Fog Lamp (Domestic...
Page 306: Vehicle Storage
306 MAINTAINING YOUR VEHICLE CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it shows a problem in the circuit that must be corrected.
Page 307 Overhead Reading Light (Overhead Console) . . . T1037 Overhead Reading Light (Rearview Mirror) ..T192 Rear Cargo ......T906 Seat Belt Indicator .
Page 308: Bulb Replacement
308 MAINTAINING YOUR VEHICLE BULB REPLACEMENT Headlight Bulb Replacement CAUTION! Do not touch the new headlight bulb with your fingers. Oil contamination will severely shorten bulb life. 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 2.
Page 309: Front Park/Turn Signal/Side Marker Lights
Front Park/Turn Signal/Side Marker Lights 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 2. Rotate the socket to the left one quarter turn to replace and replace the bulb. MAINTAINING YOUR VEHICLE 309 Front Fog Lights —...
Page 310: Back Up Light Bulb
310 MAINTAINING YOUR VEHICLE 2. Twist the bulb socket 1/4 turn to remove it from the housing. 3. Pull the bulb out of the socket and replace. Back Up Light Bulb 1. Remove the screws attaching the back up light to the rear fascia and remove the housing.
Page 311 FLUIDS AND CAPACITIES Fuel (Approximate) Engine Oil-With Filter 2.4 Liter Engines (Use API Certified SAE 5W-30 Engine Oil. Refer to your engine oil filler cap for correct SAE grade meet- ing DaimlerChrysler Material Standard MS-6395.) Cooling System * 2.4 Liter Engines (Mopar Antifreeze/Coolant 5 Year/100,000 Miles Formula) * Includes heater and coolant recovery bottle filled to MAX level.
Page 312 312 MAINTAINING YOUR VEHICLE RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluids, Lubricants and Genuine Parts Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) or equivalent. Use API Certified SAE 5W-30 Engine Oil.
Page 313 Chassis Component Automatic Transmission Fluid. Manual Transmission Fluid. Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar ATF+4 Automatic Transmission Fluid or equivalent. Mopar ATF+4 Automatic Transmission Fluid or equivalent. Mopar DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable.
Page 315 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..316 Maintenance Schedule ....316 Schedule “B”—All Engines ....319 Schedule “A”—Non Turbo .
Page 316: Emission Control System Maintenance
316 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 317 • Taxi, police, or delivery service (commercial ser- vice).† • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow schedule “B—All Engines”...
Page 318 318 MAINTENANCE SCHEDULES At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading.
Page 319: Schedule "B"-All Engines
SCHEDULE “B”—ALL ENGINES Follow schedule “B”—All Engines if you usually operate your vehicle under one or more of the following condi- tions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an Change the manual transaxle fluid every 48,000 miles (77 000 km) if the vehicle is usually operated under one or...
Page 320 320 SCHEDULE “B”—ALL ENGINES NOTE: IF ANY of these apply to you then flush and replace the engine coolant every 102,000 miles (164,000 km) or 60 months, whichever comes first, and follow schedule “B—All Engines” of the Maintenance Sched- ules section of this manual. If none of these apply to you, and your vehicle is equipped with a Non–Turbo Charged Engine then change your engine oil at every interval shown on...
Page 321 Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter, replace as necessary.* Inspect the Make-up air filter, replace as nec- essary. SCHEDULE “B”—ALL ENGINES 321 3,000 6,000 9,000...
Page 322 322 SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace as neces- sary.* Replace the Make-up air filter.
Page 323 Miles ( Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter, replace as necessary.* Change the manual transaxle fluid.†...
Page 324 324 SCHEDULE “B”—ALL ENGINES Miles ( Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if neces- sary.
Page 325 Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter and replace as necessary.* Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals.
Page 326 326 SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Rotate tires. Inspect the brake linings. Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter and replace as necessary.* Change the manual transaxle fluid.†...
Page 327 Miles (Kilometers) Change engine oil and engine oil filter, if not re- placed at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. * Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension.
Page 328 328 SCHEDULE “B”—ALL ENGINES * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emis- sions warranty. ‡ This maintenance is not required if previously replaced. † This maintenance is required only for police, taxi, limousine type operation, or trailer towing.
Page 329: Schedule "A"-Non Turbo
SCHEDULE “A”—NON TURBO Miles (Kilometers ) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension SCHEDULE “A”—NON TURBO 329 6,000...
Page 330 330 SCHEDULE “A”—NON TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace, if necessary.* Flush and replace the engine coolant at 60 months, if not done at 102,000 miles.
Page 331 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed.
Page 332 332 SCHEDULE “A”—NON TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the PCV valve and replace if necessary. * ‡ Replace the air cleaner filter. Replace the engine timing belt. * Flush and replace the engine coolant at 120 months, if not done at 102,000 miles.
Page 333: Schedule "A"-Turbo
SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension.
Page 334 334 SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Flush and replace engine coolant at 60 months, if not replaced at 100,000 miles. 35,000 40,000 45,000 (56 000) (64 000) (72 000) [42] [48]...
Page 335 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed.
Page 336 336 SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Adjust the generator drive belt tension. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary.
Page 337 Miles (Kilometers) [Month] Change engine oil and engine oil filter. Rotate tires. Inspect the PCV Valve and replace if necessary. * Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emis- sions warranty.
Page 339: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......340 Prepare For The Appointment .
Page 340: Suggestions For Obtaining Service For Your Vehicle
340 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager.
Page 341 Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to you selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service. The manufacturer’s dealers have the facilities, factory-trained...
Page 342 342 IF YOU NEED CONSUMER ASSISTANCE DaimlerChrysler Canada Inc. Customer Center P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone —(800) 465–2001 In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY)
Page 343: Warranty Information
The manufacturer will not stand behind any service contract that is not the manufacturer’s Service Contract. It is not responsible for any service contract other than the manufacturer’s Service Contract. If you purchased a service contract that is not a manufacturer’s Service Contract, and you require service after your manufactur- er’s new vehicle limited warranty expires, please refer to your contract documents, and contact the person listed in...
Page 344 344 IF YOU NEED CONSUMER ASSISTANCE U.S. ONLY...
Page 345: Mopar Parts
MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer.
Page 346: Publication Order Forms
• Owner’s Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips.
Page 347: Department Of Transportation Uniform Tire
Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada) Visit us on the World Wide Web at: www.techauthority.daimlerchrysler.com or www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway Traffic Safety Adminis- tration.
Page 348: Temperature Grades
348 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade is based on braking (straight- ahead) traction tests and does not include cornering (turning) performance. Temperature Grades The temperature grades are A (highest), B, and C, repre- senting the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 349 INDEX...
Page 350 350 INDEX ABS (Anti-Lock Brake) System ....212 Adding Engine Coolant (Antifreeze) ..286 Adding Fuel ......239 Adding Washer Fluid .
Page 351 Special Additives ..... . 296 Autostick ......143,204 Back-Up Lights .
Page 352 352 INDEX Caution, Exhaust Gas ..... . 61 CD Changer ..... . 150,161,167 CD Player .
Page 353 Inspection ......287 Points to Remember ....286,288 Pressure Cap .
Page 354 354 INDEX Emission Control System Maintenance ..267,316 Engine ......264,265 Break-In Recommendations .
Page 355 Fuel ......235,312 Adding ......239 Additives .
Page 356 356 INDEX Headlights Bulb Replacement ..... . 308 Cleaning ......301 High Beam .
Page 357 Key, Sentry ......14 Key-In Reminder ......14 Keyless Entry System .
Page 358 358 INDEX Service ......308 Theft Alarm ......137 Traction Control .
Page 359 Vanity ....... 70 Modifications/Alterations, Vehicle ... . . 7 Mopar Parts .
Page 360 360 INDEX Parking Brake ......209 Passing Light ......98 Pets .
Page 361 Refrigerant ......280 Remote Keyless Entry ..... 22 Replacement Bulbs .
Page 362 362 INDEX Security Alarm (Theft Alarm) ....26 Sentry Key ......14,27 Sentry Key Programming .
Page 363 Tachometer ......139 Temperature Gauge, Engine Coolant ..138,247 Tether Anchor, Child Restraint .
Page 364 364 INDEX Minimum Requirements ....242 Trailer and Tongue Weight ....242 Warnings .
Page 365 Warning, Door Ajar ..... . 141 Warning Lights (Instrument Cluster Description) Warnings and Cautions ..... 6 Warranty Information .
Page 366 NOTES...
Page 367 NOTES...
Page 368 NOTES...

Chrysler 2005 PT Cruiser Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Quick Links

INTRODUCTION

Chapters

Related Manuals for Chrysler 2005 PT Cruiser

Summary of Contents for Chrysler 2005 PT Cruiser