3-5: Filter2; 3-8: Filter2 Eg - Korg TRITON Extreme Manual

Br (AMS SW Break)
Specifies the direction in which "AMS (Level Mod. AMS)"
will affect "Break (Break Point Level)." When "Intensity
(AMS Intensity)" has a positive (+) value, a setting of + for
this parameter will allow "AMS (Level Mod. AMS)" to raise
the EG level, and a setting of – will allow "AMS (Level Mod.
AMS)" to lower the EG level. With a setting of 0 there will be
no change.
Filter 1 EG changes (level) (AMS = Velocity, Intensity = a positive (+) value)
Note-on
Note-off
Softly played note with "St,"
"At," and "Br" set to + (setting
of 3–4a: Filter 1 EG)
3–4c: Time Modulation
These settings let you use alternate modulation to control
the Time parameters of the filter 1 EG.
AMS1:
AMS1 (Time Mod. AMS1)
Selects the source that will control the Time parameters of
the filter 1 EG ("AMS List" ☞p.272).
Intensity (AMS1 Intensity)
Specifies the depth and direction of the effect that "AMS1
(Time Mod. AMS1)" will have.
For example if "AMS1 (Time Mod. AMS1)" is set to Flt KTr
+/+, the EG Time parameters will be controlled by the Keyboard
Track (3–2a) settings. With positive (+) values of this parame-
ter, positive (+) values of Ramp (Ramp Setting) will lengthen
the EG times, and negative (–) values of Ramp (Ramp Setting)
will shorten the EG times. The direction of change is specified
by "At (AMS1 SW Attack)," "Dc (AMS1 SW Decay)," "Sl
(AMS1 SW Slope)," and "Rl (AMS1 SW Release)."
With a setting of 0, the times specified by Filter 1 EG (3–4a)
will be used.
If "AMS1 (Time Mod. AMS1)" is set to Velocity, positive
(+) values of this parameter will cause EG times to lengthen
as you play more strongly, and negative (–) values will
cause EG times to shorten as you play more strongly.
At (AMS1 SW Attack)
Specifies the direction in which "AMS1 (Time Mod. AMS1)"
will affect the attack time. With positive (+) values of
"Intensity (AMS1 Intensity)," setting this parameter to +
will allow AMS1 to lengthen the time, and setting this
parameter to – will allow AMS1 to shorten the time. With a
setting of 0 there will be no change.
Dc (AMS1 SW Decay)
Specifies the direction in which "AMS1 (Time Mod. AMS1)"
will affect the decay time. With positive (+) values of
"Intensity (AMS1 Intensity)," setting this parameter to +
will allow AMS1 to lengthen the time, and setting this
parameter to – will allow AMS1 to shorten the time. With a
setting of 0 there will be no change.
Sl (AMS1 SW Slope)
Specifies the direction in which "AMS1 (Time Mod. AMS1)"
will affect the slope time. With positive (+) values of "Inten-
sity (AMS1 Intensity)," setting this parameter to + will
allow AMS1 to lengthen the time, and setting this parameter
to – will allow AMS1 to shorten the time. With a setting of 0
there will be no change.
22
Note-on
Note-on
Note-off
Strongly played note with Strongly played note with
"St," "At," and "Br" set to + "St," "At," and "Br" set to –
[Off, (KT, EXT)]
[–99...+99]
[–, 0, +] Rl (AMS1 SW Release)
Specifies the direction in which "AMS1 (Time Mod. AMS1)"
will affect the release time. With positive (+) values of
"Intensity (AMS1 Intensity)," setting this parameter to +
will allow AMS1 to lengthen the time, and setting this
parameter to – will allow AMS1 to shorten the time. With a
setting of 0 there will be no change.
Filter 1 EG changes (Time) (AMS = Velocity, Intensity = a positive (+) value)
Note-on
Note-off
Note-off
Softly played note with "At,"
"Dc," "Sl" and "Rl" set to +
(setting of 3–4a: Filter 1 EG)
AMS2:
AMS2 (Time Mod. AMS2)
Intensity (AMS2 Intensity)
At (AMS2 SW Attack)
Dc (AMS2 SW Decay)
Sl (AMS2 SW Slope)
Rl (AMS2 SW Release)
These parameters are the settings for AMS2 to control the
Time parameters of the filter 1 EG (☞AMS1).
▼ 3–4: Page Menu Command
3–4A: Sync Both EGs
When you select the page menu command "Sync Both
EGs," a check mark will be added at the left of "Sync Both
EGs." In this state, you can edit the filter 1 EG and filter 2 EG
simultaneously. (Editing either EG will change the settings
of both EGs.)
"Sync Both EGs" cannot separately sync the filter EG
and amp EG. For example if they are synced in 4–3A,
[–, 0, +]
they will also be synced here.
This can be selected only if "Oscillator Mode" (1–1a) is
Double.
3–5: Filter2
[–, 0, +]
3–6: Filter2 Mod.
3–7: Filter2 LFO Mod.
3–8: Filter2 EG
Make settings for filter 2 which controls the sound of oscilla-
tor 2. You can choose either a 24 dB/octave low pass filter
[–, 0, +]
with resonance or a 12 dB/octave low pass filter and 12 dB/
octave high pass filter connected in series. Filter 2 can be
used if "Oscillator Mode" (1–1a) is Double. (☞"3–1:
Filter1" – "3–4: Filter1 EG")
Note-on
Note-on
Note-off
Strongly played note with Strongly played note with
"At," "Dc," "Sl" and "Rl" set "At," "Dc," "Sl" and "Rl" set
to + to –
[Off, (KT, EXT)]
[–99...+99]
0–1A
1–1A
1–1B
3–4A
[–, 0, +]
Note-off
[–, 0, +]
[–, 0, +]
[–, 0, +]
[–, 0, +]