Korg TRITON Extreme Manual page 153

Example settings)
You can insert Valve Force at the desired location by setting
Input/Setup "BUS (IFX/Indiv.) Select" (0–2a), "BUS (IFX)
Select" (8–1b), or post-IFX "BUS Sel." (8–2a). VALVE FORCE
"BUS Sel." (9–5a) specifies the destination of the output
from Valve Force. You can sample the sound that is sent to
the bus specified by "Source BUS" (0–2b).
• Audio Input → VALVE FORCE → sampling
"BUS (IFX/Indiv.) Select": 3/4 (Tube)
VALVE FORCE "BUS Sel.": L/R or 1/2
"Source BUS": L/R or 1/2
• Audio Input → VALVE FORCE → insert effect →
sampling
"BUS (IFX/Indiv.) Select": 3/4 (Tube)
VALVE FORCE "BUS Sel.": IFX 1...5
Post-IFX "BUS Sel.": L/R or 1/2
"Source BUS": L/R or 1/2
Don't set the post-IFX "BUS Sel." to 3/4(Tube), since
doing will cause a feedback loop that may produce
unpleasant distortion.
• Audio Input → insert effect → VALVE FORCE →
sampling
"BUS (IFX/Indiv.) Select": IFX 1...5
Post-IFX "BUS Sel.": 3/4 (Tube)
VALVE FORCE "BUS Sel.": L/R or 1/2
"Source BUS": L/R or 1/2
• Audio Input → insert effect → VALVE FORCE →
insert effect → sampling
"BUS (IFX/Indiv.) Select": IFX 1...5
Post-IFX "BUS Sel.": 3/4 (Tube)
VALVE FORCE "BUS Sel.": IFX 1...5
Post-IFX "BUS Sel.": L/R or 1/2
"Source BUS": L/R or 1/2
Don't set the post-IFX "BUS Sel." to any preceding IFX,
since doing so will cause a feedback loop that may pro-
duce unpleasant distortion.
You can use Valve Force in conjunction with insert
effects even when resampling the playback of a sample.
As when sampling an audio input, use "BUS (IFX)
Select" (8–1b) and post-IFX "BUS Sel." (8–2a) to specify
the routing.
9–1b: Post VALVE FORCE Mixer
Pan(CC#8)
BUS Sel.
ADC OVERLOAD !!
These parameters specify the destination to which the Valve
Force output is sent.
Refer to Program mode for details on these parameters.
"Pan," "BUS Sel.", and "ADC OVERLOAD !!" apply
only if "Placement" is set to Insert (Use 3/4 BUS).
142
[L000...C064...R127]
[L/R, IFX1...5, 1, 2, 1/2, Off]
▼ 9–1: Page Menu Command
9–1A: Copy Valve Force
This command copies Valve Force settings from the desired
program, combination, or song, or from Sampling mode or
Song Play mode.
1 Select "Copy Valve Force" to access the dialog box.
2 Use "From" to select the copy-source mode, bank, and
number.
3 Select the parameters that you want to copy.
If you select "Controller," only Input Trim, Tube Gain,
Ultra Boost, and Output Level settings will be copied.
If you select "Placement," the Placement settings will be
copied. If the copy-source is Insert (Use 3/4 BUS), then
the Pan (CC#8), BUS Sel. settings will also be copied.
If you check "All," all settings will be copied.
4 Press the OK button to execute "Copy Valve Force," or
press the Cancel button if you decide to cancel.
9–1A