Korg TRITON Extreme Manual page 117

• Set Top Key: Select "Index" 001, set "Position" (0–3a,
3–2a) to Left (to Selected Index), and execute "Create"
or "Insert" to open the dialog box. So that a new index
can be created at the left of index 1, re-set the "Top
Key" setting, and press the OK button.
• Set Zone Range: If you execute "Create" when it is not
possible to create a new index according to the Create
Zone Preference settings, the following dialog box will
appear. This dialog box will also appear if you execute
"Insert" when it is not possible to create a new index
with the contents of the "Cut" or "Copy" (3–1c). Re-set
the "Zone Range" (0–3a, 3–2a), and press the OK
button.
Stereo
A indication will appear here if you have selected a
stereo multisample or sample, or if you recorded a sample
with "Sample Mode" (0–1c) set to Stereo.
About stereo multisamples and stereo samples
Stereo multisamples: Under the following conditions, two
multisamples will be handled as a stereo multisample.
• If you checked "Stereo" when creating a new
multisample (i.e., selected a new multisample in "MS"
0–1a)
• If you executed the "MS Mono To Stereo" (0–1H) page
menu command
• If you sampled with "Sample Mode" (0–1c) set to Stereo
In these cases, a stereo multisample will be created auto-
matically using the following criteria.
1. The last two characters of the two multisample names
will be -L and -R respectively, and the earlier portion of
the names are identical.
2. The two multisamples will have the same number of
indexes, and their zone settings are identical.
Stereo samples: Under the following condition, two sam-
ples will be handled as a stereo sample.
• When the samples were recorded with a "Sample
Mode" (0–1c) setting of Stereo
• If you executed the "Sample Mono To Stereo" (0–1I)
page menu command
In these cases, a stereo multisample will be created auto-
matically using the following criteria.
1. The last two characters of the sample name will be -L
and -R respectively, and the earlier portion of the
names are identical.
2. Two samples that satisfy condition 1. for stereo multi-
samples are selected.
Stereo multisamples and samples are distinguished
internally by their multisample name or sample name.
If you use "Rename MS" (0–1F) or "Rename Sample"
(0–1C) etc. to modify the multisample name or sample
name, please pay attention to the above conditions.
As a condition of a stereo sample, the sampling rates
must be identical. You can verify the sampling rate of a
sample by using the page menu command "Rate Con-
vert" (1–1K). Be aware that if you use "Rate Convert" to
convert the -L and -R samples to differing sampling
rates, they will not be handled as a stereo sample.
106
0–1c: REC Sample Setup
Here you can select the memory bank into which you will
sample, specify the sampling time, and select either mono or
stereo sampling.
Save to
Specifies the destination to which the data will be written
during sampling.
RAM: The sound will be sampled into sample memory (RAM).
A sample written into sample memory can be heard imme-
diately in Sampling mode.
Data written into sample memory (RAM) will be lost
when the power is turned off, so you must save it if you
want to keep it.
MEDIA: Sample to media.
Use the page menu command "Select Directory" (0–1N) to
select the writing-destination media and directory, and to
specify the filename.
When you sample, a WAVE file will be created.
To hear the results of sampling, you can either load the file
in Media mode into sample memory (RAM), or use the page
menu command "Select Directory" etc. to select the file, and
then press the SAMPLING [START/STOP] key.
A sample (WAVE file) of up to 16 Mbyte in size (mono)
or 32 Mbyte (stereo) can be loaded into sample memory
(RAM) from media, as long as the sample memory has
been expanded to 32 Mbyte or more.
You can't sample or resample to media on a device con-
nected to the USB A connector.
Bank (RAM BANK)
Specifies the RAM bank and sample number into which the
data will be written during sampling. This can be specified if
RAM is selected for "Save to."
Sample memory (RAM) consists of six banks, each with 16
Mbytes. The TRITON Extreme comes with one 16 Mbyte of
DRAM SIMM board. In this state, RAM1 will always be
selected for "Bank (RAM Bank)," and RAM2, 3, 4, 5, and 6
cannot be selected.
By adding additional DRAM SIMM boards, you can expand
the memory to a maximum of 96 Mbytes (when three 32
Mbyte SIMM boards are installed). (☞p.319)
How installed SIMM's relate to available banks
SIMM SIMM RAM
Time
Slot No. capacity Bank
Slot 1 16 Mbyte 1 16 Mbyte: approximately 2 minutes
32 Mbyte 1, 2
Slot 2 16 Mbyte 3 96 Mbyte: approximately 2 minutes
32 Mbyte 3, 4
Slot 3 16 Mbyte 5
32 Mbyte 5, 6
The TRITON Extreme is shipped with a 16 Mbyte
SIMM installed in Slot 1. This allows you to select only
RAM1 for "Bank (RAM Bank)."
For example, if Slot 1 contains the factory-installed 16
Mbyte SIMM, and you have installed a 32 Mbyte SIMM
in Slot 2 and a 16 Mbyte SIMM in Slot 3, you will be
able to select RAM1 (16 Mbyte), RAM3 (16 Mbyte),
RAM4 (16 Mbyte), and RAM5 (16 Mbyte) for "Bank
(RAM)." Each bank is 16 Mbytes.
(If a 32 Mbyte SIMM is installed in each Slot1, Slot2,
and Slot3, all banks can be selected, and the total size
will be 96 Mbytes.)
[RAM, MEDIA]
[RAM1...RAM6]
54 seconds (mono)
approximately 1 minute
27 seconds (stereo)
54 seconds (mono) x 6
total of approximately 17
minutes 28 seconds
approximately 1 minute
27 seconds (stereo) x 6
total of approximately 8
minutes 44 seconds