Combination P8: Edit-Insert Fx; 8-1: Routing - Korg TRITON Extreme Manual

Combination P8: Edit–Insert FX
You can also specify the bus routing for the program used by
each timbre 1–8.
☞For details on insertion effects, refer to p.205 "8. Effect
Guide."
8–1: Routing
Specifies the bus to which the program oscillator(s) used by
each timbre 1–8 will be sent. You can also set the send levels
to the master effects from this page.
2–1a
8–1b
8–1a: Routing Map
This shows the status of the insert effects. For each insert
effect, this indicates the routing, the name of the selected
effect, the on/off status, and chain status.
The effect type, on/off status and chain status can be modi-
fied in the Insert FX page (8–2).
8–1b: BUS Select (IFX/Indiv.Out BUS Select),
Send1 (MFX1), Send2 (MFX2)
BUS Select (IFX/Indiv.Out BUS Select)
IFX1...5, 1, 2, 3(Tube), 4(Tube),1/2, 3/4(Tube), Off]
For each timbre 1–8, these parameters specify the bus to
which the program oscillator(s) will be sent. The current set-
tings can also be viewed in the Routing Map.
DKit: This can be selected only if the program for which set-
tings are being made is a drum program ("Oscillator Mode"
Drums). With a setting of DKit, the "BUS Select" (Global P5:
5–2b) setting made for each key of the drum kit will be used.
For example if the "BUS Select" settings of the drum kit
have assigned Snare sounds to IFX1 and Kick sounds to
IFX2, setting this parameter to DKit will send the Snare
sounds to IFX1 and Kick sounds to IFX2. If you wish to
modify these routings, use the page menu command "Drum
Kit IFX Patch" (8–1C).
If you want to insert Valve Force into the program oscil-
lator output of a timbre, select 3/4(Tube), 3(Tube), or 4
(Tube). Set the Valve Force "Placement" (9–5a) to
Insert.
If this is set to 1/2 or 3/4(Tube), the programs of timbres
1–8 will be sent in stereo from AUDIO OUTPUT (INDI-
VIDUAL) 1/2 or 3/4. If the pan of the program oscilla-
tor is controlled by MIDI control change CC#10 (pan) or
AMS, the sound will be output with the pan setting that
is in effect at the moment of note-on. Unlike the case
when this parameter is set to L/R to output the sound
from (MAIN) L/MONO and R, the pan of a sounding
note will not change in realtime.
If you wish to move the pan of a sounding note in real-
time and output it from AUDIO OUTPUT (INDIVID-
UAL) 1/2 or 3/4, you must set "BUS Select" to IFX1
(or IFX2–IFX5), select 000: No Effect for "IFX1" (or
IFX2–IFX5) (8–2), and for the sound that has passed
through the IFX, set "BUS Select" (8–2) to either 1/2 or
3/4(Tube).
Send1 (MFX1)
Send2 (MFX2)
For each timbre 1–8, these parameters set the send level to
master effects 1 and 2. These settings are valid when "BUS
Select" is set to L/R or Off. When IFX 1, 2, 3, 4 or 5 are
selected, the send levels to master effects 1 and 2 are set by
the "Send 1" and "Send 2" parameters of the Insert FX page,
8–1 after the sound has passed through IFX1–5.
If "BUS Select" is set to 1, 2, 3(Tube), 4(Tube), 1/2, or 3/
8–1a
4(Tube), these settings are ignored.
Control change CC#93 can be used to control the Send 1
level, and CC#91 to control the Send 2, and modify their
respective settings. These messages will be received on
the MIDI channel specified for each timbre in the P2:
MIDI channel page.
The actual send levels are determined by multiplying
this value with the send level "Send 1" and "Send 2"
(Program P8: 8–1d) for each oscillator of the program
selected for the timbre.
▼ 8–1: Page Menu Command
8–1A: Copy Insert Effect
☞Program P8: 8–1A: Copy Insert Effect.
[DKit, L/R,
However, the MIDI control channel specified for "Ctrl Ch"
of the IFX1–5 pages will not be copied.
8–1B: Swap Insert Effect
☞Program P8: 8–1B: Swap Insert Effect.
However, the MIDI control channel specified for "Ctrl Ch"
of the IFX1–5 pages will not be swapped.
8–1C: DrumKit IFX Patch
This command applies a patch to the "BUS Select" settings
of each key of the drum kit, allowing you to temporarily
change the connections to the insert effects. This command
is available only if a drum program has been selected for the
timbre and the "BUS Select" (8–1b) parameter is set to Dkit.
Furthermore, this command can be executed only if the
"BUS Select" (Global P5: 5–2b) for the individual keys of
that drum kit are set to IFX1–5.
1 Select "DKit IFX Patch" to access the dialog box.
[000...127]
[000...127]
0–1A
0–1B
8–1A
8–1B
8–1C
51