Korg TRITON Extreme Manual page 36

Time:
Attack (Attack Time)
Specifies the time over which the volume will change after
note-on until it reaches the attack level.
If the start level is 0, this will be the rise time of the sound.
Decay (Decay Time)
Specifies the time over which the volume will change from
when it reaches the attack level until it reaches the break
point level.
Slope (Slope Time)
Specifies the time over which the volume will change from
when it reaches the break point level until it reaches the sus-
tain level.
Release (Release Time)
Specifies the time over which the volume will change after
note-off until it reaches 0.
Amplifier EG
Attack Level
Note-on
Break Point
Volume
Start
Level
Attack Decay Slope
Time Time Time
4–3b: Level Modulation
Specifies how AMS will control the amp 1 EG level specified
in "Amp1 EG" (4–3a).
AMS (Level Mod.AMS)
Selects the source that will control the Level parameters of
the amp 1 EG ("AMS List" ☞p.272).
Intensity (AMS Intensity)
Specifies the depth and direction of the effect that "AMS
(Level Mod.AMS)" will have.
For example if "AMS (Level Mod.AMS)" is Velocity, setting
"St (AMS SW Start)," "At (AMS SW Attack)," and "Br (AMS
SW Break)" to + and setting "Intensity (AMS Intensity)" to a
positive (+) value will cause the amp 1 EG volume levels to
increase as you play more strongly. Setting "Intensity (AMS
Intensity)" to a negative (–) values will cause the amp 1 EG
volume levels to decrease as you play more strongly. With a
setting of 0, the levels will be as specified in "Amp1 EG" (4–
3a).
St (AMS SW Start)
Specifies the direction in which "AMS (Level Mod.AMS)"
will change "Start (Start Level)." If "Intensity (AMS Inten-
sity)" is set to a positive (+) value, setting this parameter to
+ will allow AMS to increase the EG level, and setting this
parameter to – will allow AMS to decrease the EG level.
With a setting of 0, no change will occur.
At (AMS SW Attack)
Specifies the direction in which "AMS (Level Mod.AMS)"
will change "Attack (Attack Level)." If "Intensity (AMS
Intensity)" is set to a positive (+) value, setting this parame-
ter to + will allow AMS to increase the EG level, and setting
this parameter to – will allow AMS to decrease the EG level.
With a setting of 0, no change will occur.
[00...99]
[00...99]
[00...99]
[00...99]
Note-off
Sustain
Level
Time
Release Time
[Off, (KT, EXT)]
[–99...+99]
[–, 0, +]
[–, 0, +]
Br (AMS SW Break)
Specifies the direction in which "AMS (Level Mod.AMS)"
will change "Break (Break Point Level)." If "Intensity (AMS
Intensity)" is set to a positive (+) value, setting this parame-
ter to + will allow AMS to increase the EG level, and setting
this parameter to – will allow AMS to decrease the EG level.
With a setting of 0, no change will occur.
Amp 1 EG changes (Level) (AMS=Velocity, Intensity = a positive (+) value)
Note-on Note-on
Note-off
Softly played note when "St"=0 Strongly played note
and "At" and "Br" are set to + when "St"=0 and "At" and
(settings of 4–3a: Amp 1 EG) "Br" are set to +
4–3c: Time Modulation
These parameters let you use an alternate modulation
source to modify the amp 1 EG times that were specified in
Amp1 EG (4–3a).
AMS1 (Time Mod. AMS1)
Selects the source that will control the Time parameters of
the amp 1 EG ("AMS List" ☞p.272).
Intensity (AMS1 Intensity)
Specifies the depth and direction of the effect that "AMS1
(Time Mod. AMS1)" will have.
For example if "AMS1 (Time Mod. AMS1)" is Amp KTrk +/
+, the (Amp) Keyboard Track settings (4–2a) will control the
EG Time parameters. With positive (+) values of this param-
eter, positive (+) values of Ramp will cause EG times to be
lengthened, and negative (–) values of Ramp will cause EG
times to be shortened. The direction of the change is speci-
fied by "At (AMS1 SW Attack)," "Dc (AMS1 SW Decay),"
"Sl (AMS1 SW Slope)," and "Rl (AMS1 SW Release)."
When "AMS1 (Time Mod. AMS1)" is Velocity, positive (+)
values will cause EG times to lengthen as you play more
strongly, and negative (–) values will cause EG times to
shorten as you play more strongly. With a setting of 0, the EG
times will be as specified in Amp1 EG (4–3a).
At (AMS1 SW Attack)
Specifies the direction of the effect that "AMS1 (Time Mod.
AMS1)" will have on "Attack (Attack Time)." With positive
(+) values of "Intensity (AMS1 Intensity)," setting this
parameter to + will allow AMS1 to lengthen the time, and
setting it to – will allow AMS1 to shorten the time. With a
setting of 0 there will be no effect.
Dc (AMS1 SW Decay)
Specifies the direction of the effect that "AMS1 (Time Mod.
AMS1)" will have on "Decay (Decay Time)." With positive
(+) values of "Intensity (AMS1 Intensity)," setting this
parameter to + will allow AMS1 to lengthen the time, and
setting it to – will allow AMS1 to shorten the time. With a
setting of 0 there will be no effect.
Sl (AMS1 SW Slope)
Specifies the direction of the effect that "AMS1 (Time Mod.
AMS1)" will have on "Slope (Slope Time)." With positive
(+) values of "Intensity (AMS1 Intensity)," setting this
parameter to + will allow AMS1 to lengthen the time, and
setting it to – will allow AMS1 to shorten the time. With a
setting of 0 there will be no effect.
[–, 0, +]
Note-on
Note-off Note-off
Strongly played note
when "St"=0 and "At" and
"Br" are set to –
[Off, (KT, EXT)]
[–99...+99]
[–, 0, +]
[–, 0, +]
[–, 0, +]
25