Korg TRITON Extreme Manual page 44

MFX1, 2 On/Off
Switches the master effects 1, 2 on/off. When off, the output
will be muted. This will alternate between on and off each
time it is pressed.
CC#94 can be used to switch the MFX on and off. A
value of 0 will be off, and a value of 1–127 will be the
original setting. This is controlled on the global MIDI
channel "MIDI Channel" (Global P1: 1–1a).
Chain
On (checked): Chain (series connection) will be turned on
for MFX1 and MFX2.
Off (unchecked): MFX1 and MFX2 will operate in parallel.
Chain Direction [MFX1→MFX2, MFX2→MFX1]
Specifies the direction of the connection when MFX1 and
MFX2 are chained.
MFX1→MFX2: Connect from MFX1 to MFX2.
MFX2→MFX1: Connect from MFX2 to MFX1.
Chain Signal
When chain is On, this parameter specifies how the stereo
output signal of the first master effect will be connected to
the input (mono) of the next master effect.
L/R Mix: The stereo output L/R of the first master effect will
be mixed before being input to the next master effect.
L Only, R Only: Only the left or right channel of the output
will be input to the next master effect.
Chain Level
When chain is On, this sets the level at which the sound is
sent from the first master effect to the next master effect.
9–1b: Return Level
Return 1, 2
Adjusts the return levels from the master effects to the L/R
bus (main output L/MONO, R).
9–1c: Master EQ Gain [dB]
Sets the gain for the three-band EQ located immediately
before the sound of the L/R bus is sent from the AUDIO
OUTPUT (MAIN OUT) L/MONO and R jacks. This is
linked with the various "Gain" parameters of Master EQ (9–
4).
Low
Mid
High
The cutoff frequency for "Low," "Mid" and "High" and the
"Q" of "Mid" can be adjusted in the Master EQ page. These
settings are in "dB" units.
[Off, ON]
[Off, On]
[LR Mix, L Only, R Only]
[000...127]
[000...127]
[–18.0...+18.0]
[–18.0...+18.0]
[–18.0...+18.0]
▼ 9–1: Page Menu Command
9–1A: Copy Master Effect
This command lets you copy any desired effect settings from
Program, Combination, Song, Sampling, or Song Play mode.
1 Select "Copy Master Effect" to access the dialog box.
2 In "From," select the copy source mode, bank, and num-
ber.
3 Select the effect that you want to copy.
If you select MFX1 or MFX2, "Return" (return level) will
be copied at the same time.
If you select Master EQ, only the master EQ settings will
be copied.
You can select from an insert effect by selecting IFX 1–5.
If you check "All," all settings for the master effects and
master EQ will be copied.
If you are copying from an insert effect, differences in
routing and level will mean that the result will not be
completely identical.
4 In "To," specify the copy destination master effects.
5 To execute the Copy Master Effect command, press the
OK button. To cancel, press the Cancel button.
9–1B: Swap Master Effect
This command swaps (exchanges) the settings of MFX1 and
MFX2.
1 Select "Swap Master Effect" to access the dialog box.
2 To execute the Swap Master Effect command, press the
OK button. To cancel, press the Cancel button.
0–1A
9–1A
9–1B
33