Program P1: Edit-Basic; 1-1: Program Basic - Korg TRITON Extreme Manual

If you want to hear the sound that is being sampled, use
INDIV. 1, 2 OUT. Connect AUDIO OUTPUT MAIN L,
R, INDIV 1, 2 to your mixer or audio system, and moni-
tor the output.
If you've set "Source Audio" to S/P DIF, use "System
Clock" (Global P0: 0–2a) to change the system clock.
If you want to apply an insert effect to the input source,
go to the Program P0: Play, Sampling page, and set
Input 1,2 "BUS (IFX/Indiv.) Select" to IFX1–IFX5. Set
the "BUS Select" that follows the insert effect you used
to 1/2.
For additional information, refer to
selected Resample Program Play."
Automatically-set parameters and their values
Parameter 1. Initialize
Input (Input Source): Analog, S/P DIF
Input1:
Level 127
Pan L000
BUS Select Off
Send1 000
Send2 000
Input2:
Level 127
Pan R127
BUS Select Off
Send1 000
Send2 000
Sampling Setup:
Source BUS L/R
Trigger Note On
Metronome Precount Off
Save to RAM
Mode Stereo
Sample Time: RAM Maximum
Sample Time: MEDIA 4min 59.999sec
Recording Level [dB] –12.0
Select Bank & Smpl No.
(Page Menu Command):
Auto +12dB On On
Convert to Program Off
Program -
MS -
Orig.Key -
- : Not set automatically
Values enclosed in parentheses ( ) are automatically set
according to the settings you make in the dialog box.
*1
:Settings for Analog, S/P DIF ("Input 1" and "Input 2") are
made automatically.
*2
:The input source setting ("Input 1" and "Input 2") you
specified for "Source Audio" in the dialog box will be set
automatically.
*3
:If "Source Audio" is Mono-1 this will be L-Mono, if
Mono-2 this will be R-Mono, and if Stereo this will be
Stereo.
*4
:When "Save to: RAM," and "Convert to Program" is
checked.
b)–f) in "If you
2. Resample
Program/ 3. REC
Combination Audio Input
Play
*1 *2 *2
(Source Audio) (Source Audio)
127 127
L000 L000
Off 1/2
000 000
000 000
127 127
R127 R127
Off 1/2
000 000
000 000
L/R Indiv.1/2
Note On Sampling START SW
- -
(Save to) (Save to)
*3
Stereo (Source Audio)
- -
- -
–12.0 +0.0
On Off
(Convert to Program) (Convert to Program)
(Program) (Program)
*4 *4
Newly created Newly created
*4 *4
C2 C2
Program P1: Edit–Basic
Here you can adjust basic program settings, such as oscilla-
tor mode and scale type.
1–1: Program Basic
1–1a
1–1c
1–1a: Oscillator Mode
Oscillator Mode
Specifies the Program's oscillator assignment; whether it
will use one or two oscillators, or a drum kit.
Single: The program will use one oscillator (Oscillator 1,
Filter 1, Amplifier 1). In this case the program will normally
have a maximum of 60-note polyphony.
Double: The program will use two oscillators (Oscillator 1/
2, Filter 1/2, Amplifier 1/2). In this case the program will
normally have a maximum of 30-note polyphony.
Drums: The program will use one oscillator (as when Single
is selected), but Oscillator 1 will be assigned a drum kit
instead of a multisample. In this case the program will nor-
mally have a maximum of 60-note polyphony.
If a program draws one multisample from the ROM
bank, and a second from either the Piano bank or one of
the installed EXB boards, then in this case, a Single pro-
gram can have a maximum of 120-note polyphony, a
Double program a maximum of 60-note polyphony,
and a Drums program a maximum of 120-note polyph-
ony. (☞OG p.12)
1–1b: Voice Assign Mode
Mode (Voice Assign Mode)
Poly: The program will play polyphonically, allowing you
play chords.
Mono: The program will play monophonically, producing
only one note at a time.
Single Trigger
This is available when the "Mode (Voice Assign Mode)"
setting is set to Poly.
On (checked): When the same note is played repeatedly, the
previous note will be silenced before the next note is
sounded, so that the notes do not overlap.
Legato
This is available when the "Mode (Voice Assign Mode)"
setting is set to Mono.
On (checked): Legato is on. When multiple note-on's occur,
the first note-on will retrigger the sound, and the second and
subsequent note-on's will not retrigger.
1–1
1–1b
[Single, Double, Drums]
[Poly, Mono]
[Off, On]
[Off, On]
9