Sampling P8: Insert Effect; Output; Make Chain Settings - Korg TRITON Extreme Manual

Sampling P8: Insert Effect

Here you can make insert effect settings for use in Sampling
mode.
If you want to apply insert effect IFX1–5 to the external
audio signal specified by "Input" and sample the result, set
the P0: Recording, Input/Setup page Input1 and Input2
"BUS (IFX/Indiv.) Select" parameters to IFX1–5, and adjust
the effect settings.
If you want to apply effects to a previously-sampled sample
or a sample you loaded, and resample the result, set the P8:
Insert Effect page "BUS (IFX) Select" parameter to IFX1–5,
and adjust the effect settings. (☞"Resample" 0–2b)
☞For details on insert effects, refer to p.205 "8. Effect
Guide."
In Sampling mode, master effects 1 and 2 and the mas-
ter EQ cannot be used.
Insertion effect settings in Sampling mode are not
backed up when the power is turned off. If you wish to
keep the insertion effect settings, you can use "Copy
Insert Effect."
For example, you can copy the insertion effect settings
of Sampling mode to a program or combination in
order save them. When you write the program or com-
bination, the settings will be saved in internal memory.
In Sampling mode, you can use "Copy Insert Effect" (8–
1A) to copy these effect settings from the program or
combination back into Sampling mode and use them.
8–1: Routing
8–1a
8–1b
8–1a: Routing Map
Routing Map
This displays the status of the insert effect settings.
Insert effect routing, the name of the specified effect, on/off,
and chain are displayed. Insert effect type, on/off, and chain
settings are made in the P8: Edit-Insert Effect, Insert FX
page.
8–1b: BUS Select
BUS(IFX) Select
[L/R, IFX1...5, 1, 2, 3(Tube), 4(Tube), 1/2, 3/4(Tube), Off]
Selects the bus.
If you want to apply an effect to a sample (multisample) that
you sampled or loaded, select IFX1–5. (☞"Resample" 0–2b)
After you resample, L/R will automatically be selected
as the "BUS (IFX) Select" setting. Be aware of this
when you want to resample again.
140
▼ 8–1: Page Menu Command
8–1A: Copy Insert Effect
☞Program P8: 8–1A: Copy Insert Effect.
8–1B: Swap Insert Effect
☞Program P8: 8–1B: Swap Insert Effect.
8–2: Insert FX
Here you can select the type of the insert effects, turn them
on/off, and make chain settings.
8–2a
8–2b
8–2a: IFX1, 2, 3, 4, 5
IFX1, 5
8–1
IFX2, 3, 4
IFX1, 2, 3, 4, 5 On/Off
Chain
Pan(CC#8) (Post IFX PanCC#8)
These parameters specify the type of insert effect, and its
on/off, chain, and pan settings. For details on the parame-
ters refer to Program P8–2a.
BUS Sel. (BUS Select)
[L/R, 1, 2, 3(Tube), 4(Tube), 1/2, 3/4(Tube)]
This specifies the bus to which the signal will be sent after
passing through the insert effect. Normally you will set this
to L/R. If you want to send the signal to AUDIO OUTPUT
(INDIVIDUAL), choose 1, 2, 3(Tube), 4(Tube), 1/2, or 3/4
(Tube).
If you want to insert Valve Force after the insert effect,
select 3/4(Tube), 3(Tube), or 4(Tube). Set the Valve
Force "Placement" to Insert.
8–1A
8–1B
8–1
[000...089]
[000...102]
[Off, ON]
[Off, On]
[L000...C064...R127]