Korg TRITON Extreme Manual page 223

Send1 responds to CC#93 and Send2 responds to
CC#91 on MIDI Global channel "MIDI Channel" (Glo-
bal P1: 1–1a). At this time, the actual send level uses the
value of the Send 1 and 2 settings for Oscillators 1 and
2, multiplied by the Send 1 and 2 values received via
MIDI.
If you have selected "Drums" for "Oscillator Mode" (Pro-
gram P1: 1–1a) of a Program, the "Use DKit Setting" box
(Program P8: 8–1b) becomes available.
If you check this box, Send1 and Send2 levels for each key
of the selected DrumKit become effective. If "BUS Select"
(Global P5: 5–2b) is set to L/R or Off for a drum instrument
key, "Send1 (to MFX1)" and "Send2(toMFX2)" (Global P5:
5–2b) become effective. If "BUS Select" is set to IFX1–5,
"Send1" and "Send2" (Program P8: 8–2a) become effective.
If this is unchecked, the routing will be the same as when
"Oscillator Mode" is Single or Double, and the "Send1
(MFX1)" and "Send2 (MFX2)" (Program P8: 8–1d) settings
or the post-IFX1–5 "Send1" and "Send2" settings of the P8:
Insert FX page IFX1–5 (Program P8: 8–2a) will apply to all
drum instruments.
2–2. Combination, Sequencer, and Song Play
modes
Use "Send1 (MFX1)" and "Send2 (MFX2)" (P8: "Routing"
page) for timbres (Combination) and tracks (Sequencer,
Song Play) to set the Send1 and 2 levels for each timbre and
track. As with Program mode, if "BUS Select" is set to L/R
or Off, "Send1 (MFX1)" and "Send2 (MFX2)" become effec-
tive. At this time, the actual levels use these Send1 and 2
level values, multiplied by the send level values of oscilla-
tors 1 and 2 ("Oscillator Mode" is set to "Double") of the
Program P8: "Routing" page.
– Send level –
For example, if a Program's "OSC1 Send1" is set to 127,
"Send2" set to 064, "OSC2 Send1" set to 064, "Send2" set to
127, a Combination's "Send1" set to 064, and "Send2" set to
127, the actual send levels of the combination are calculated
as follows:
OSC1 Send1=127 (100%)*064(50%)=064(50%)
OSC1 Send2=064 (50%)*127(100%)=064(50%)
OSC2 Send1=064 (50%)*064(50%)=032(25%)
OSC2 Send2=127 (100%)*127(100%)=127(100%)
If IFX1–5 is selected for "BUS Select", use the "Send1" and
"Send2" parameters for the post-IFX signals.
If 1, 2, 3(Tube), 4(Tube), 1/2, or 3/4(Tube) is selected instead,
these Send1 and 2 settings are ignored and the Master Effect
is not applied.
Send1 responds to CC#93, and Send2 responds to
CC#91. If "Send1 (MFX1)" and Send2 (MFX2)" for each
timbre/track are effective, the parameter will be con-
trolled on the MIDI channels set for the corresponding
timbres and tracks. If the "Send1" and "Send2" param-
eters for the post-IFX1–5 signals are effective, they can
be controlled on the MIDI channels assigned to IFX1–5.
The following examples are in Combination mode. In the
upper figure, "BUS Select" is set so that Timbre 1 is routed
to IFX1, Timbre 2 to IFX2, Timbre 3 to IFX3, Timbre 4 to
IFX4, Timbres 5 and 6 to IFX5, and Timbres 7 and 8 to L/R.
In this case, use "Send1" and "Send2" for the post-IFX1(001:
St. Amp Simulation) signal to set the send level of the Tim-
bre 1 routed to the Master Effect. (In this example they are
set to 032 and 127.) In the same way, use "Send1" and
"Send2" for the post-IFX2, 3, and 4 signals to set the send
levels of Timbres 2, 3, and 4, and use the "Send1" and
"Send2" parameters for the post-IFX5 signal to set the send
levels of Timbres 5 and 6. For Timbres 7 and 8, the settings of
212
"Send1 (MFX1)" and "Send2 (MFX2)" will be effective. (At
this time, the actual send levels use these Send 1 and 2 val-
ues multiplied by the Send1 and 2 settings for Program
oscillators 1 and 2.)
If drum Programs are selected for timbres in Combination
mode and for tracks in Sequencer mode and Song Play
mode, you can select "DKit" for "BUS Select." If you select
"DKit," the "BUS Select" (Global P5: 5–2b) settings for each
key become effective, and each drum instrument sound will
be routed to the corresponding buses. At this time, the
actual send levels use these Send 1 and 2 values, multiplied
by the Send1 and 2 settings for each DrumKit key. (Use the
"Send1" and "Send2" parameters for the post-IFX1–5 signal
to set the send levels for the DrumKit keys for which the
"BUS Select" parameters are set to IFX1–5.) If L/R or Off are
selected, this Send1 or 2 level will be multiplied by the send
levels specified in the Program P8: Routing page parameters
"OSC1 Send1 (to MFX1)" and "Send2 (to MFX2)" (Program
P8: 8–1d), in the same way as when "Oscillator Mode" is
Single or Double. If "BUS Select" is set to IFX1–5, use
"Send1" and "Send2" for the post-IFX signal. If "BUS Select"
is set to 1, 2, 3(Tube), 4(Tube), 1/2, or 3/4(Tube), the Send 1
and 2 settings will be ignored.
2–3. Sampling Mode
You cannot use the Master Effects and Master EQ in Sam-
pling mode.
2–4. Audio Input, S/P DIF IN
In Program, Combination, Sequencer, Song Play, and Media
modes, the insert effects, master effects, and master EQ can
be applied to the external input sound from the AUDIO
INPUT 1, 2, and S/P DIF IN jacks.
You can make this setting in "Input (COMBI, PROG, SEQ,
S.PLAY, MEDIA)" of each mode; the setting is shared by all
modes. This setting can be accessed from Global P0: Basic
Setup, Input/Sampling page; Combination or Program P0:
Play, Sampling page; Sequencer P0: Play/REC, Sampling
page; and Media, Play Audio CD page.
Set "BUS (IFX/Indiv. Select)" to specify the bus to which the
external audio input will be sent. You can select L/R, IFX1–5,
1, 2, 3(Tube), 4(Tube), 1/2, 3/4(Tube), or Off. If "BUS Select"
(Global P0: 0–3a) is set to L/R or Off, adjust the send levels
to the master effects using "Send 1 (to MFX1)" and "Send 2
(to MFX2)." If BUS Select is set to IFX1–5, use the post-IFX
"Send 1" and "Send 2." (☞"3. Mixer")