Filter/Dynamic; Filter And Dynamics Control Effects; 000: No Effect; 001: St. Amp Simulation (Stereo Amp Simulation) - Korg TRITON Extreme Manual

Filter/Dynamic

Filter and dynamics control effects

000: No Effect

Select this option when you do not use any effects. The Insert
Effect section outputs unprocessed signals and the Master
Effect section mutes the output.
001: St. Amp Simulation
(Stereo Amp Simulation)
This effect simulates the frequency response characteristics of
guitar amplifiers. It produces a realistic effect as though the
sound were being played through a guitar amp. It is also
effective for organ and drum sounds.
Stereo In - Stereo Out
Left
Amp Simulation Filter
Amp Simulation Filter
Right
Amplifier Type
a
Selects the type of guitar amplifier
Wet/Dry
Sets the balance between the effect and dry sounds
Src
b
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance

002: Stereo Compressor

This effect compresses the input signal to regulate the level
and give a "punchy" effect. It is useful for guitar, piano, and
drum sounds. This is a stereo compressor. You can link left
and right channels, or use each channel separately.
Stereo In - Stereo Out
Left
EQ Trim
LEQ HEQ
Envelope - Control
Envelope Select
Envelope - Control
EQ Trim LEQ HEQ
Right
Envelope Select
a Determines whether the left and right channels are linked or used
separately
Sensitivity
b
Sets the sensitivity
Attack
c
Sets the attack level
EQ Trim
d
Sets the EQ input level
Wet / Dry
Wet / Dry
SS, EL84, 6L6
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
Wet / Dry
Compressor
Output Level
Output Level
Compressor
Wet / Dry
L/R Mix, L/R Individually
☞
1...100
☞
1...100
☞
0...100
Pre LEQ Gain [dB]
Sets the gain of Low EQ
e
Pre HEQ Gain [dB]
Sets the gain of High EQ
Output Level
Sets the output level of the compressor
Src
f
Selects the modulation source for the compressor output level
Amt
Sets the modulation amount of the compressor output level
Wet/Dry
Sets the balance between the effect and dry sounds
Src
g
Selects the modulation source of the effect balance
Amt
Sets the modulation amount of the effect balance
a: Envelope Select
This parameter selects whether the left and right channels are
linked to control both signals simultaneously, or whether each
channel is controlled independently.
b: Sensitivity, f: Output Level
The "Sensitivity" parameter sets the sensitivity of the compressor.
If this parameter is set to a higher value, lower level sounds will
be boosted. With a higher Sensitivity, the overall volume level is
higher. To adjust the final volume level, use the "Output Level"
parameter.
Level
Wet
Dry
c: Attack
This parameter controls the attack level.
Level
Attack=80
Attack=20
Dry

003: Stereo Limiter

The Limiter regulates the input signal level. It is similar to the
Compressor, except that the Limiter compresses only signals
that exceed the specified level to lower unnecessary peak sig-
nals. The Limiter applies a peaking-type EQ to the trigger sig-
nal (which controls the degree of the Limiter effect), allowing
you to set any band width to be covered. This effect is a stereo
limiter. You can link left and right channels, or use each chan-
nel individually.
Stereo In - Stereo Out
Left
Side PEQ
Envelope - Control
+
Envelope - Control
Envelope Select
Right
–15.0...+15.0dB
–15.0...+15.0dB
0...100
☞
,
Off...Tempo
–100...+100
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
Compressor - Sensitivity
Sensitivity=100
Sensitivity=40
Time
Compressor - Attack
Wet
Time
Wet / Dry
Gain Adjust
Limiter
Trigger Monitor
Limiter
Gain Adjust
Wet / Dry
217