HP X5000 G2 Administrator's Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Network Hardware
  5. X5000 G2
  6. Administrator's manual
HP X5000 G2 Administrator's Manual

HP X5000 G2 Administrator's Manual

Hp network storage system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

HP X5000 G2 Network Storage System

Administrator Guide
Abstract
This document explains how to install, configure, and maintain all models of the HP X5000 G2 Network Storage System and
is intended for system administrators. For the latest version of this guide, go to www.hp.com/support/manuals. Select NAS
Systems in the storage group, and then select an X5000 G2 product.
HP Part Number: QW919-96035
Published: July 2013
Edition: 4

Advertisement

Table of Contents
loading

Related Manuals for HP X5000 G2

Summary of Contents for HP X5000 G2

  • Page 1: Hp X5000 G2 Network Storage System

    Administrator Guide Abstract This document explains how to install, configure, and maintain all models of the HP X5000 G2 Network Storage System and is intended for system administrators. For the latest version of this guide, go to www.hp.com/support/manuals. Select NAS Systems in the storage group, and then select an X5000 G2 product.
  • Page 2 The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

  • Page 3: Table Of Contents

    Contents 1 HP X5000 G2 Network Storage System............7 Features..........................7 Hardware components......................7 Software components........................8 2 Installing the storage system.................9 Verify the kit contents........................9 Locate and record the product number, serial number, and SAID number.........9 Unpack and rack the storage system hardware................9 Cable disk enclosures......................10...
  • Page 4 Removing and replacing the fan module..................75 Removing and replacing the power UID button assembly.............76 Removing and replacing the power supply.................77 Removing and replacing the HP Ethernet I/O module..............78 Removing and replacing the PCIe module (with card)..............79 Removing and replacing the EMU module.................81 Removing and replacing the server blade backplane..............82...
  • Page 5 8 Support and other resources..............128 Contacting HP........................128 HP technical support......................128 Subscription service......................128 Related information.......................128 HP websites........................128 Rack stability........................129 9 Documentation feedback.................130 A Managing the EMU................131 CLI reference........................131 Command line conventions....................131 Operational groups......................131 Authentication........................132 Time functions........................135 Inventory and status......................138 Internet control........................143 Server management......................146...
  • Page 6 Laser compliance notices.......................165 English laser notice......................165 Dutch laser notice......................165 French laser notice......................165 German laser notice......................166 Italian laser notice......................166 Japanese laser notice.......................166 Spanish laser notice......................167 Recycling notices........................167 English recycling notice....................167 Bulgarian recycling notice....................168 Czech recycling notice......................168 Danish recycling notice.....................168 Dutch recycling notice.......................168 Estonian recycling notice....................169 Finnish recycling notice.....................169 French recycling notice.....................169...

  • Page 7: Hp X5000 G2 Network Storage System

    The HP X5000 G2 Network Storage System (“storage system”) is an integrated hardware-software solution that provides highly available file and block storage on a Windows failover cluster. Each storage system features HP server blades and dense disk storage in a single 3U enclosure (Figure 1 (page 7)).

  • Page 8: Software Components

    Figure 2 Rear view 1. System fan 2. HP 2-port 10 Gb I/O module (2). These modules connect to the NIC located on the server blade motherboard. 3. Intraconnect (internal switch connecting servers and EMU) 4. Drive fan 5. SAS I/O module (2) 6.

  • Page 9: Installing The Storage System

    D2600 or D2700 disk enclosures may be connected to the storage system. Rail kit Power cords Media and documentation HP X5000 G2 Network Storage System Quick Start Guide HP ProLiant Essentials Integrated Lights-Out Advanced Pack End User License Agreement HP X5000 G2 System Recovery DVD...

  • Page 10: Cable Disk Enclosures

    The following figures show the correct cabling of disk enclosures to the storage system chassis. Numbers represent the order of attachment. Figure 4 (page 11) shows an HP X5000 G2 Network Storage System with two disk enclosures. Installing the storage system...
  • Page 11 NOTE: Up to four HP D2600 or HP D2700 disk enclosures are supported. A mix of HP D2600 or HP D2700 disk enclosures is not supported. Figure 4 X5000 G2 with two disk enclosures 1. X5000 G2 2–3. Disk enclosures 4.

  • Page 12: Network Connections

    Figure 5 X5000 G2 with four disk enclosures 1. X5000 G2 2–5. Disk enclosures 6. SAS cable connecting disk enclosure 1 (green cable) 7. Green color code for upper SAS I/O module 8. Red color code for lower SAS I/O module 9.
  • Page 13 In the network infrastructure that connects the cluster nodes, avoid having single points of failure. One way to do this is to have at least two distinct networks. The HP X5000 G2 already provides one network between the nodes—the Cluster Internal network. You must add at least one more network.

  • Page 14: Power On The Storage System

    Figure 7 Cabling an additional network Connect 10 GbE Public 1 (Blade 1) and 10 GbE Public 2 (Blade 2) to the same subnet in your network infrastructure. Note that adapters were chosen on different pass-through modules. This prevents the pass-through module from becoming a single point of failure for the connection between the two nodes.

  • Page 15: Configure The Emu And Ilo Management Processors

    Configure the EMU and iLO management processors Before configuring the management processors, verify the following: You have determined whether the network ports on the server are to use DHCP or static addresses. If the network ports are to use static addresses, you must provide the addresses. For this step, the EMU port should not be connected to a switch.
  • Page 16 After you have logged into iLO, HP recommends that you change the administrator password. To do so, select User Administration under Administration in the iLO management interface.
  • Page 17 Configure the EMU: Connect to the Enclosure Manager software using an ssh compatible tool like PuTTY. In the PuTTY session basic options, enter the EMU IP address (10.0.0.10) and port (22), and select SSH for the connection type (Figure 9 (page 17)).
  • Page 18 CustomerEMU-dnsName> set password New Password: ******** Confirm : ******** Changed password for the "Administrator" user account. CustomerEMU-dnsName> NOTE: You will not be able to connect to iLO or the EMU from the configuration system until you change the network settings on the configuration system. Complete the configuration: Connect the EMU port to the appropriate switch/VLAN/subnet.

  • Page 19: Configuring The Storage System

    For instructions on using iLO, see the Integrated Lights Out user guide available from http:// www.hp.com/go/ilo. On the iLO web page, select More iLO Documentation. Set up Windows and discover the second node When the storage system starts, the servers will begin a first time setup procedure that takes approximately 10 to 15 minutes, including the Set Up Windows wizard.

  • Page 20: Completing Initial Configuration

    After logon, the HP ICT window is launched automatically. Figure 12 ICT window Use the HP ICT to perform setup tasks in the order they appear. See the provided online help for each group of tasks for more information about the task. After completing the “Provide cluster name and domain”...

  • Page 21: Networking Options

    Networking options The large number of network adapters on each server in the X5000 G2 provides a number of different options for networking. The network adapter named "Cluster Internal" is pre-configured as a private cluster heartbeat and should be left as is, but all other adapters are available for use.

  • Page 22: Monitoring And Troubleshooting The Storage System

    The ProLiant SNMP agents are enabled on the storage system by default and should not be disabled as they are used for internal management functions. If they are enabled for external client consumption, HP SIM must be configured so it does not attempt to communicate with these agents.
  • Page 23 Figure 13 Configuring Alerts and Email Do one of the following: Select New to create a profile. Select Copy or Edit to modify an existing profile. The Alert Settings window appears. Configuring Alerts and Email...
  • Page 24 Figure 14 Alert and Email settings Complete the following fields: Name—Enter the name of a recipient (for example, John Doe). Recipient address—Enter the email address of the recipient (for example, John.Doe@company.com). From address—Enter an email address that will display to the recipient indicating where the message originated.
  • Page 25 Right-click and select Properties to display the SNMP Service properties. Select the Security tab and specify the following items: The external hosts that may use the SNMP protocol. The SNMP Community string. HP recommends that you use something other than the typical ‘Public’ string. IMPORTANT: Configure HP SIM security to prevent the SIM management server from gaining access to SNMP.

  • Page 26: Hp System Management Homepage

    The HP System Management Homepage (SMH) is a web-based interface that consolidates and simplifies single system management for HP servers. The SMH is the primary tool for identifying and troubleshooting hardware issues in the storage system. You may choose this option to diagnose a suspected hardware problem.
  • Page 27 Because both a system and drive fan are required, the maximum and minimum number of fans required is two. If either fan becomes degraded, the system could shut down quickly. Because the fans are not mutually redundant, even if the status of a single fan has changed, HP System Management Homepage...
  • Page 28 the new status is reported immediately in the Components Status Summary section on the SMH main page. When the Enclosure Manager IP address is set incorrectly, the enclosure status displayed is Lost communication. Because the Enclosure Manager has lost communication with the external network, none of the other items in the Enclosure Information section can be displayed.
  • Page 29 The Storage Pools page also displays a list of disk drives and storage volumes present in the pool. Under the Physical Drives tree, the list of disk enclosures is displayed. Under each enclosure, the list of disk drives present in each disk enclosures is displayed. When there is no drive in HP System Management Homepage...

  • Page 30: Using The System Manager

    the enclosure, the display shows Bay Bay number – Empty. Select one of the disk enclosures or disk drives to see information for that enclosure or drive. Physical Drives This section provides an overview of all disk drives attached to the controller. Drives are identified and grouped as assigned, unassigned, and spare drives.

  • Page 31: Hardware Status

    Figure 20 System summary Hardware Status The Hardware Status tab provides the health status for each storage system component. The System section displays information for the server blade that you are logged in to. If a problem is reported in the System section, you should check the Hardware Status tab on each server blade. NOTE: If the System Manager shows that a LUN has an error, open the System Management Homepage and determine whether the LUN is degraded due to a disk failure.
  • Page 32 Since the tool does not connect to the Internet to identify new firmware, you must periodically check the HP support web page and download new firmware when available. Be sure to check the Firmware tab on each server blade. Some firmware updates must be made on both server blades.
  • Page 33 The Reports tab gathers logs for the hardware, software, Microsoft Windows system configuration, and the Microsoft Exchange diagnostics in one place. These logs are used by HP support engineers to help diagnose your system, if needed; you do not need to view and interpret the logs yourself.

  • Page 34: Component Leds

    Figure 23 Reports Component LEDs LEDs indicate the status of hardware components. This section provides images of the component LED locations and describes the status of LED behaviors. To obtain additional information on some status indicators, you can use the EMU CLI SHOW commands described in “Managing the EMU”...
  • Page 35 Table 2 Server blade LEDs status (continued) Item Description Status Amber = Degraded condition Red = Critical condition NIC 1 LED* Green = Network linked Green flashing = Network activity OFF = No link or activity Flex- 1 0 NIC 2 LED* Green = Network linked Green flashing = Network activity OFF = No link or activity...
  • Page 36 Table 3 Front LED status (continued) Item Description Status Hard drive LEDs Green = The drive has been selected by a management application and it is operating normally. Drive locate mode (UID LED is Flashing amber (1 Hz) = The drive is not selected and is indicating a flashing) predictive failure.
  • Page 37 Table 4 SAS hard drive LED combinations (continued) Item Description Status Blinking green (@ 4 Hz 50% of duty cycle) = Drive is currently performing I/O activity <and> Drive is a member of a RAID volume <and> Drive is not in a replacement or failed state for any volumes that is a member of a RAID volume (drive is online) <and>...
  • Page 38 The health LED is only green and is either on (Healthy) or off (Power off or Faulted). LEDs are off when the enclosure is powered off. Figure 29 HP 2-port 1 GB Ethernet I/O modules LEDs Table 7 HP 2-port 1 GB Ethernet I/O modules LEDs status Item Description Status...
  • Page 39 Figure 30 HP 2-port 1 GB Ethernet, Mezz A and B I/O modules LEDs Table 8 HP 2-port 1 GB Ethernet, Mezz A and B I/O modules LEDs status Item Description Status Module health LED Solid green when module health is good...
  • Page 40 Figure 32 Power supply LEDs Table 10 Power supply LED status Item Description Status Power supply Green = Power on and power supply functioning properly. OFF = One or more of the following conditions exists: System powered off, AC power unavailable, Power supply failed, Power supply exceeded current limit.
  • Page 41 Table 1 1 Chassis switches and indicator LEDs status (continued) Item Description Status OFF if system health is good. Power button/LED Green when enclosure power is ON. Amber when enclosure has AC power but is turned off. Figure 34 SAS I/O modules LEDs Table 12 SAS I/O module LEDs status Item Description...

  • Page 42: Emu Cli Show Commands

    Figure 35 Fan LEDs The two fan modules are physically identical, but their control is not. The Fault/health LED on FAN 1 is a single bi-color LED controlled by the EMU via the Health Monitor – it is either off, steady green, or flashing amber.

  • Page 43: Known Issues

    Type 'HELP HELP' to display more detailed information about the help system. EM-78E7D1C140F2> After logging in, you can set the Administrator password using the Enclosure Manager Settings window. Go to the C:\Program Files\HP\HP Configuration Wizard directory and double-click HPEMConfig.exe. Known issues...
  • Page 44 This issue is documented by Microsoft at: http://technet.microsoft.com/en-us/library/gg214171(WS.10).aspx Several utilities do not operate with the The HP X5000 G2 Network Storage System does not have a VDS Hardware HP X5000 G2 Network Storage System. Provider, so the following utilities do not work:...
  • Page 45 For example, if the drive letter for the corrupted disk is Q: then you would run chkdsk q:. The NFS user mapping should not use HP strongly recommends using Active Directory or other RFC2307 compliant ADLDS. LDAP stores for NFS user name mapping. Using Active Directory Lightweight Data Services (ADLDS) is not recommended.
  • Page 46 When configuring iLO settings in the Log on to the second node using the local administrator account and Initial Configuration Tasks window, configure the iLO settings using the iLO Configuration Utility in the HP changing iLO settings on the second System Tools program group.

  • Page 47: Using Storage Viewer

    Table 13 Known issues (continued) Issue Resolution A drive letter is selected for a new This is a temporary condition that exists only until the volume has been added volume in the Create a Volume wizard, to the cluster as a cluster disk. Afterwards, the volume appears on the owner but that drive letter is used only on one node with the desired drive letter.
  • Page 48 Figure 36 Storage Viewer (LUNs view) You can also view details about each drive – bay location, ID, serial number, size, health, and model number. In the lower part of the tool, you can view volume information related to the drive. Monitoring and troubleshooting the storage system...

  • Page 49: Hp Support Websites

    The guide provides common procedures and solutions for many levels of troubleshooting with a ProLiant server. IMPORTANT: Some troubleshooting procedures found in ProLiant server guides may not apply to the storage system. If necessary, check with your HP Support representative for further assistance. HP Support websites...

  • Page 50: Hp Insight Remote Support Software

    Notifications may be sent to your authorized HP Channel Partner for onsite service, if configured and available in your country. The software is available in two variants: HP Insight Remote Support Standard: This software supports server and storage devices and is optimized for environments with 1 to 50 servers.

  • Page 51: Microsoft Systems Center Operations Manager

    The storage system hardware is preconfigured for Insight Remote Support and uses the WMI (WBEM) provider. Register the system using the X5000 G2 product number and serial number, instead of the blade serial number and part number. Confirm and overwrite any prepopulated values with the serial number of the storage system.
  • Page 52 Select Windows Recovery Environment. The recovery environment is loaded. Once the recovery environment is loaded, the System Recovery Options wizard opens. On the first window, select the keyboard input method, which is based on your location (for example, select US for United States) and click Next. Select either of the following options (it does not matter which option is selected) and click Next: Use recovery tools that can help fix problems starting Windows.

  • Page 53: Memory Diagnostic

    You should only use this tool under the guidance of HP Support to avoid potential data loss. The tool is included (but not installed) with HP X5000 G2 software version 2.02.0a or later. To install the tool: Navigte to the C:\hpnas\support directory on the server blade.

  • Page 54: Obtaining The Service Agreement Id

    Before the tool opens, a disclaimer about potential data loss is displayed. Read the disclaimer and accept the terms to continue. If you decline, the tool closes. When the HP 1210m Volume Online Tool opens, the LUNs that are in an Enabled but Offline state are displayed.

  • Page 55: Upgrading The Storage System

    When HP determines that it is desirable to upgrade one or more of these components, a notification is posted to the HP support website for the HP X5000 G2 Network Storage System with the release notes and the updated code. HP recommends that you upgrade the storage system software as part of normal system maintenance for increased reliability and a better customer experience.

  • Page 56: Upgrading X5000 G2 Software

    Select Drivers and Software. Enter X5000 G2 in the Enter a product name/number box and click Search. Select your X5000 G2 product, select the operating system, and then select the service release. Follow the instructions included with the service release for installation.
  • Page 57 HP 1210m controller System ROM (I24) for the server blade Power Management controller firmware (c-Class blades) Smart Array HP P410i Blade HDD controller Enclosure Manager Unit (EMU) External half of the SAS I/O module Internal half of the SAS I/O module...
  • Page 58 If, after upgrading the firmware on the controllers, the storage system does not see any storage or the controllers do not start, see “Resolving errors after the HP 1210m controller upgrade” (page 59).

  • Page 59: Resolving Errors After The Hp 1210M Controller Upgrade

    Resolving errors after the HP 1210m controller upgrade If the firmware upgrade for the HP 1210m controller does not complete successfully, the controllers could stop responding. As a result, the Controller Properties dialog box in Windows Device Manager displays “This device cannot start” and the storage system Configuration Wizard fails to detect storage.

  • Page 60: Resolving An Emu Upgrade Issue

    “Removing and replacing hardware components” (page 61). For example, to replace the HP 1 GB Ethernet I/O module with a 10 GB module, follow the instructions in “Removing and replacing the HP Ethernet I/O module” (page 78). If you need to shut down a server blade or the storage system to replace a component, follow the instructions in “Powering the storage system off...

  • Page 61: Removing And Replacing Hardware Components

    This chapter describes procedures for removing and replacing hardware components. Customer self repair HP customer self repair (CSR) programs allow you to repair your HP product. If a CSR part needs replacing, HP ships the part directly to you so that you can install it at your convenience. Some parts do not qualify for CSR.

  • Page 62: Identifying The Spare Part

    Optional CSR — You can order the part directly from HP and repair the product yourself, or you can request that HP repair the product. If you request repair from HP, you may be charged for the repair depending on the product warranty.
  • Page 63 Figure 44 Exploded view of the system Table 14 (page 64) lists the CSR replaceable parts for the system. Replaceable parts...
  • Page 64 Table 14 Storage system replaceable parts Replacement type (Cold, Item Replaceable unit (RU) Part number CSR availability Warm, Hot) Server interposer 631 1 17-001 Optional Cold Midplane board 631 1 15-001 Cold (Not shown) .5 M mini SAS cable 408765-001 Mandatory (Not shown) Mini SAS cable 2 M...

  • Page 65: Hot, Warm, And Cold Swap Components

    Table 15 Related component documents Component Component name Guide Server blade X5460sb blades HP ProLiant BL460c G7 Server Blade Maintenance and Service Guide Disks in disk The large form factor (LFF) supports 12 3.5-inch HP D2600/D2700 Disk Enclosure User Guide enclosures disk drives and the small form factor (SFF) supports 25 2.5-inch disk drives.

  • Page 66: Verifying Component Failure

    Verifying component failure Use the following methods to verify component failure: Analyze any failure messages received. Fault monitoring software from HP provides a recommended action. From the System Manager, select the System Summary tab to check the enclosure health status or select the Hardware Status tab to identify a failed component.

  • Page 67: Removing The System Enclosure From The Rack

    Removing the system enclosure from the rack Extend the hard drive drawer (Figure 45 (page 67)): Press upward on the release button on the hard drive drawer (1). Pull the drawer handle down 90 degrees (2). Extend the hard drive drawer (3). Figure 45 Extending the hard drive drawer Label the hard drives (Figure 46 (page...

  • Page 68: Inserting The System Enclosure Into The Rack

    Unscrew the retaining screws from the bezel ears, and then remove the enclosure from the rack. WARNING! The system enclosure is heavy, even after removing the hard drives. Always use at least two people to remove the system from the rack. Inserting the system enclosure into the rack Place the enclosure into the rack, and secure the enclosure by tightening the two retaining screws.
  • Page 69 Remove the top back panel by pressing the panel release button and lifting the latch to slide the top back panel off. Open the release handle (1, Figure 48 (page 69)), and pull up to remove the server interposer board (2, Figure 48 (page 69)).

  • Page 70: Removing And Replacing The Midplane Board

    Removing and replacing the midplane board Removing the midplane board Verify the failed component as described in “Verifying component failure” (page 66). Power off the system as described in “Powering the storage system off and on” (page 60). Remove the enclosure from the rack as described in “Removing the system enclosure from the rack”...
  • Page 71 Unplug the coil power assembly from the midplane board (Figure 52 (page 71)). Figure 52 Unplugging the coil power assembly Extend the server blades. 10. Remove the server blade airflow baffle from inside the enclosure (Figure 53 (page 71)). Figure 53 Removing the server blade airflow baffle 1 1.
  • Page 72 12. Complete the following (Figure 55 (page 72)): Loosen the two thumbscrews holding midplane board in place (1). Pull the captive locking pin out of the midplane board (2). Lift the midplane board out of the enclosure (3). Figure 55 Removing the midplane board Replacing the midplane board On the replacement midplane board, pull out the captive locking pin as you lower the board into the enclosure (1,...

  • Page 73: Removing And Replacing A Sas Cable

    1 1. Replace the top back panel. 12. Reinsert all rear components in the enclosure. 13. Replace the enclosure in the rack as described in “Inserting the system enclosure into the rack” (page 68). Removing and replacing a SAS cable CAUTION: Remove only one cable at a time to prevent downtime.
  • Page 74 Push down on the SAS I/O module lever (2, Figure 57 (page 74)), and then remove the failed SAS I/O module (3, Figure 57 (page 74)). NOTE: You may need to use significant force to accomplish this task. Figure 57 Removing the SAS I/O module Replacing the SAS I/O module To install the replacement SAS I/O module (Figure 58 (page...

  • Page 75: Removing And Replacing The Fan Module

    Confirm the firmware version. Confirm that the system has resumed normal operations. Removing and replacing the fan module There are two fan modules: one server fan module, which cools the server half of the enclosure, and one hard drive fan module, which cools the drive half of the enclosure. The two fan modules are not redundant for each other.

  • Page 76: Removing And Replacing The Power Uid Button Assembly

    Replacing the fan module Insert the replacement fan module (Figure 60 (page 76)). Figure 60 Replacing the fan module Verify that the replacement component is working properly by checking the associated LED status. NOTE: It should take approximately 15 seconds for the LED status to appear. Confirm that the system has resumed normal operations.

  • Page 77: Removing And Replacing The Power Supply

    Complete the following (Figure 62 (page 77)): Unplug the cable from the power UID button assembly (1). Remove the screw from the power UID button assembly (2). Remove the faulty power UID button assembly (3). Figure 62 Removing the power UID button assembly Replacing the power UID button assembly Complete the following (Figure 63 (page...

  • Page 78: Removing And Replacing The Hp Ethernet I/O Module

    Verify the failed component as described in “Verifying component failure” (page 66). Label the cables, and then unplug all cables from the HP Ethernet I/O module. Press the module release mechanism to the right (1, Figure 64 (page 78)), and then remove the failed module (2).

  • Page 79: Removing And Replacing The Pcie Module (With Card)

    Verify that the replacement component is working properly by checking the associated LED status. NOTE: It should take approximately 15 seconds for the LED status to display. Confirm the firmware version. Confirm that the system has resumed normal operations. Removing and replacing the PCIe module (with card) Removing the PCIe module Verify the failed component as described in “Verifying component failure”...
  • Page 80 Complete the following (Figure 67 (page 80)): Remove the two screws from the bracket of the failed PCIe module (1). Remove the bracket (2). Remove the PCIe card from the failed module (3). Figure 67 Removing the PCIe card Replacing the PCIe module Install the PCIe card in the replacement module (1, Figure 68 (page 80)), replace the bracket...

  • Page 81: Removing And Replacing The Emu Module

    Figure 69 Installing the PCIe module Plug in all cables to the PCIe module in their original locations. Power on the server blade by pressing the power button ON. Verify that the replacement component is working properly by checking the associated LED status.

  • Page 82: Removing And Replacing The Server Blade Backplane

    Replacing the EMU module Insert the replacement EMU module and ensure the release lever locks in place (Figure 71 (page 82)). Figure 71 Installing the EMU Plug the cables back into the EMU module. Verify that the new component is working properly by checking the associated LED status. Confirm the firmware version.
  • Page 83 Complete the following (Figure 72 (page 83)): Unplug the power cable from the server blade backplane by pinching the plug release mechanism (1). Remove the screw (2). Remove the server blade backplane from the enclosure (3). Figure 72 Removing the server blade backplane Replacing the server blade backplane Complete the following (Figure 73 (page...

  • Page 84: Removing And Replacing The Server Airflow Baffle

    Replace the midplane board (Figure 74 (page 84)): Pull out the captive locking pin as you lower the board into the enclosure (1). Push the captive locking pin into the midplane board (2). Tighten the two thumbscrews holding the midplane board in place (3). Figure 74 Installing the midplane board Plug the rear UID PCA into the midplane board.

  • Page 85: Removing And Replacing The Front Bezel (Standard)

    Replacing the server airflow baffle Install the replacement server blade airflow baffle (Figure 76 (page 85)). Figure 76 Installing the server blade airflow baffle Reinstall the top back panel. Replace the enclosure as described in “Inserting the system enclosure into the rack” (page 68).

  • Page 86: Replacing The Front Bezel

    Remove all eight screws from the front bezel (1, Figure 78 (page 86)), and then lift the front bezel up and out to remove the front bezel (2). NOTE: There are two screws on the bottom, four screws on the sides (two on each side), and two screws hidden behind the handle.

  • Page 87: Removing And Replacing The Front Bezel (Full)

    Removing and replacing the front bezel (full) NOTE: This full procedure is only required if all screws are not accessible due to the position of the system in the rack. Removing the front bezel (full) Power off the system as described in “Powering the storage system off and on”...

  • Page 88: Removing And Replacing The Front Led Display Board In The Rack (Standard)

    Replacing the front bezel (full) Install the replacement front bezel with the handle at a 90 degree angle, making sure the bottom pins are aligned with the bottom holes (1, Figure 81 (page 88)), and replace the screws in the front bezel (2). NOTE: There are two screws on the bottom, four screws on the sides (two on each side), and two screws hidden behind the handle.

  • Page 89: Removing And Replacing The Front Led Display Board (Full)

    Complete the following (Figure 82 (page 89)): Disconnect the LED display board from the drive backplane by pinching the ends of the LED display board cable together (1). Remove the four screws from the LED display board (2). Remove the LED display board from the drive drawer (3). Figure 82 Removing the front LED display board Replacing the front LED display board in the rack Complete the following...
  • Page 90 Pull the hard drive drawer handle down 90 degrees, and slide out the hard drive drawer. Remove all eight screws from front bezel (1, Figure 84 (page 90)). Then, lift the front bezel up and out to remove the front bezel (2). NOTE: There are two screws on the bottom, four screws on the sides (two on each side), and two screws hidden behind the handle.

  • Page 91: Removing And Replacing A Drive Drawer

    Replacing the front LED display board (full) Complete the following (Figure 86 (page 91)): Install the replacement LED display board (1). Replace the four LED display board screws (2). Reconnect the LED display board to the drive drawer (3). Figure 86 Installing the front LED display board Replace the front bezel as described in “Replacing the front bezel (full)”...
  • Page 92 Figure 88 Removing the SAS I/O module Extend the drive drawer (Figure 45 (page 67)): Press upward on the release button on the hard drive drawer (1). Pull the drawer handle down 90 degrees (2). Extend the hard drive drawer (3). Figure 89 Extending the hard drive drawer NOTE: You must repeat Step 8 for the remaining SAS I/O module.
  • Page 93 Figure 90 Removing the plug bracket from the coil power plug 10. Unplug the coil power assembly from the midplane board (Figure 91 (page 93)). Figure 91 Unplugging the coil power assembly 1 1. Press the release mechanism on the side rail (1, Figure 92 (page 93)), and then pull the hard drive drawer fully out of the enclosure (2).
  • Page 94 Replacing the drive drawer Unlock the side enclosure rail and push it into the back enclosure (Figure 93 (page 94)). Align the bottom replacement drive drawer rails with the bottom enclosure rails. Figure 93 Unlocking the enclosure rails Align the side rails and then push the replacement drive drawer partially back into the system enclosure until approximately two inches of the drawer is still out of the enclosure (Figure 94 (page...
  • Page 95 Figure 95 Connecting the coil power assembly to the midplane board Reattach the plug bracket (1, Figure 96 (page 95)) to the coil power plug and tighten the thumbscrew (2). Figure 96 Reattaching the plug bracket to the coil power plug Push the drive drawer fully back into the system enclosure (1, Figure 97 (page 96)) and the...

  • Page 96: Removing And Replacing The Drive Drawer Hard Drive

    Figure 97 Pushing the drive drawer into the system enclosure Replace the top back panel. Replace the drive fan module. Replace both SAS I/O modules. 10. Replace the enclosure as described in “Inserting the system enclosure into the rack” (page 68).
  • Page 97 Extend the hard drive drawer (Figure 98 (page 97)): Press upward on the release button on the hard drive drawer (1). Pull the drawer handle down 90 degrees (2). Extend the hard drive drawer (3). Figure 98 Extending the hard drive drawer Locate the failed hard drive.

  • Page 98: Removing And Replacing The Drive Drawer Rails (Side Or Bottom)

    Replacing the drive drawer hard drive Install the hard drive (Figure 100 (page 98)): Insert the replacement hard drive with the lever in the open position (1). Push the release lever into place (2). Figure 100 Installing the hard drive Push the drive drawer back into the system enclosure.
  • Page 99 Extend the hard drive drawer (Figure 101 (page 99)): Press upward on the release button on the hard drive drawer (1). Pull the drawer handle down 90 degrees (2). Extend the hard drive drawer (3). Figure 101 Extending the hard drive drawer Remove the plug bracket (2, Figure 102 (page 99)) from the coil power plug by removing the...
  • Page 100 Figure 103 Unplugging the coil power assembly Press the release mechanism on the side rail (1, Figure 104 (page 100)), and then pull the hard drive drawer fully out of the enclosure (2). WARNING! The hard drive drawer is heavy, even after removing the hard drives. Make sure the drawer is fully supported as you remove it from the enclosure.
  • Page 101 Lift the release tab on the side or bottom rail (1, Figure 105 (page 101)), and then slide the rail toward the front of the drive drawer to remove the rail (2). NOTE: Repeat this step for all rails. Figure 105 Removing the drive drawer rails Replacing the drive drawer rails Align the replacement rail with the tabs, and slide it toward the back of the drive drawer until the rail locks into place...
  • Page 102 Figure 107 Partially installing the drive drawer Pull the cable slightly out of the coil power plug and connect it to the midplane board (Figure 108 (page 102)). Figure 108 Connecting the coil power assembly to the midplane board Reattach the plug bracket (1, Figure 109 (page 103)) to the coil power plug and tighten the thumbscrew (2).

  • Page 103: Removing And Replacing The Enclosure Rails

    Figure 109 Reattaching the plug bracket to the coil power plug Push the drive drawer fully back into the system enclosure (1, Figure 1 10 (page 103)) and the handle back into place (2). Figure 1 10 Pushing the drive drawer into the system enclosure Replace the top back panel.
  • Page 104 Extend the hard drive drawer (Figure 1 1 1 (page 104)): Press upward on the release button on the hard drive drawer (1). Pull the drawer handle down 90 degrees (2). Extend the hard drive drawer (3). Figure 1 1 1 Extending the hard drive drawer Remove the plug bracket (2, Figure 1 12 (page 104)) from the coil power plug by removing the...
  • Page 105 Figure 1 13 Unplugging the coil power assembly Press the release mechanism on the side rail (1, Figure 1 14 (page 105)), and then pull the hard drive drawer fully out of the enclosure (2). Figure 1 14 Removing the drive drawer Lift the release mechanism on the rail (side or bottom) (1, Figure 1 15 (page 105)), and then...
  • Page 106 Replacing the enclosure rails Align the replacement rail, and then attach it by sliding the rail toward the front of the enclosure (Figure 1 16 (page 106)). Figure 1 16 Installing the enclosure rails Align the replacement drive drawer rail with the three enclosure rails and then push the drive drawer partially back into the system enclosure so that approximately two inches of the drawer is still out of the enclosure (Figure 1 17 (page...
  • Page 107 Figure 1 18 Connecting the coil power assembly to the midplane board Reattach the plug bracket (1, Figure 1 19 (page 107)) to the coil power plug and tighten the thumbscrew (2). Figure 1 19 Reattaching the plug bracket to the coil power plug Push the drive drawer fully back into the system enclosure (1, Figure 120 (page 108)) and the...

  • Page 108: Removing And Replacing The Rack Rails

    “Inserting the system enclosure into the rack” (page 68). Removing and replacing the rack rails For detailed instructions on installing the rack rails, see the HP 3U Storage System Rail Kit Installation Instructions. Removing and replacing server blades Removing the server blade CAUTION: Do not use the server blade release lever to lift or carry the server blade.

  • Page 109: Removing And Replacing The Server Blade Hard Drive

    Place the server blade on a flat, level work surface. WARNING! To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: To prevent damage to electrical components, properly ground the server blade before beginning any installation procedure.
  • Page 110 Remove the server blade hard drive (Figure 123 (page 110)): Press the release button (1). Pull the release lever (2). Remove the hard drive (3). CAUTION: To prevent improper cooling and thermal damage, replace the drive quickly. Do not operate the server unless all bays are populated. Figure 123 Removing the server blade hard drive Replacing the server blade hard drive Install the hard drive...

  • Page 111: Removing And Replacing The 1210M Controller Board Components

    Removing and replacing the 1210m controller board components Removing the 1210m controller card WARNING! Wear gloves or use care when removing the capacitor pack to avoid physical injury. Verify the failed component as described in “Verifying component failure” (page 66). Back up all data.
  • Page 112 Remove the capacitor pack (2, Figure 127 (page 112)). The 1210m cache module (1) and the 1210m controller card (3) are also shown. Figure 127 Removing the capacitor pack NOTE: Be sure to first remove the capacitor pack bracket. 10. Loosen the two captive screws and remove the 1210m controller card (Figure 128 (page 112)).

  • Page 113: Removing And Replacing The 1210M Cache Module

    Replacing the 1210m controller card Install the cache module and capacitor in the cache module slot of the replacement controller. Close the ejector latches on the cache module slot. Install the replacement controller card (1, Figure 129 (page 113)). Press down on the connector to seat the card (2).
  • Page 114 Remove the server blade (Figure 130 (page 114)): Push the button to release the handle (1). Pull the handle toward you (2). Remove the server blade (3). Figure 130 Removing the server blade Press the release button on the access panel and slide the access panel to the left to remove The original 1210m cache module is connected to a capacitor pack, so observe the cache module LEDs: If the amber 1210m cache LED is solid, data transfer to the flash device on the cache is...
  • Page 115 Figure 132 Removing the cache module and the capacitor pack NOTE: Be sure to first remove the capacitor pack bracket. Disconnect the capacitor pack cable from the connector on the top of the cache module (Figure 133 (page 115)). Figure 133 Disconnecting the capacitor pack cable Replacing the cache module Connect the capacitor pack cable to the replacement cache module.

  • Page 116: Removing And Replacing The Capacitor Pack

    Complete the following (Figure 134 (page 116)): Install the replacement cache module in the cache module slot (1). Close the ejector latches on the cache module slot (2). Figure 134 Replacing the cache module Install the capacitor pack bracket and insert the capacitor pack on the chassis wall. Install the access panel.
  • Page 117 The original capacitor pack is connected to a cache module, so observe the cache module LEDs: If the amber cache LED is solid, data transfer to the flash device on the cache is in progress. Do not remove the cache until the amber LED is off, and then continue with the next step. If the amber cache LED is not lit, proceed to the next step.

  • Page 118: Removing And Replacing The Mezzanine Nic

    NOTE: Be sure to first remove the capacitor pack bracket. Disconnect the capacitor pack cable on the top of the cache module (Figure 138 (page 118)). Figure 138 Disconnecting the capacitor cable from the module Replacing the capacitor pack Connect the replacement capacitor pack to the cache module. Install the cache module in the cache module slot.
  • Page 119 Remove the server blade (Figure 139 (page 119)): Push the button to release the handle (1). Pull the handle toward you (2). Remove the server blade (3). Figure 139 Removing the server blade Press the release button on the access panel and slide the access panel to the left to it. The Mezzanine NIC is under the controller card.

  • Page 120: Storage System Recovery

    7 Storage system recovery This chapter describes how to perform a system recovery. To restore the X5000 G2 to the factory defaults, see “Restoring the factory image with a DVD or USB flash device” (page 121). To restore the X5000 G2 using Windows Recovery Environment, see “Restoring the system with Windows...

  • Page 121: Drive Letters Are Not Assigned After A Restore

    Drive letters are not assigned after a restore When a system that has existing data volumes (non-operating system volumes) is restored using the System Recovery DVD, the data volumes will not have drive letters assigned to them. This is by design.

  • Page 122: Recovering Both Servers

    LUNs on the shared storage as well. These LUNs will likely be from a previous cluster on the X5000 G2. Decide if you want to keep these LUNs and add them to the new cluster later. If you do not want to keep the existing LUNs, you may select them for deletion in the Create Witness Disk wizard.
  • Page 123 When the Set Up Windows wizard appears, select your desired language, regional settings, keyboard layout, and accept the EULA. After completing the wizard, an attempt is made to discover the second node. The attempt fails and the following error message displays. Figure 141 Error message during second node discovery Click Cancel.
  • Page 124 Figure 142 Changing the computer name/domain After the server has rebooted, log on as the local administrator. To manage the server as a cluster member in the future, use at least one domain user as a member of the local administrators group.

  • Page 125: Restoring The System With Windows Recovery Environment

    Windows Server Backup utility. Do one of the following: For direct access, attach the SUV cable (supplied with the HP X5000 G2 Network Storage System) to the port on the front of the server blade you want to recover. Connect a monitor and USB mouse to the SUV cable.
  • Page 126 Reboot the server blade to either the USB flash device or USB DVD drive. The system BIOS attempts to boot to the USB device first by default. Watch the monitor output during the boot as you may need to press a key to boot to the USB media. NOTE: If directly connected, you may have to change the BIOS settings to ensure proper boot sequence.
  • Page 127 IMPORTANT: Do not interrupt the recovery process. 12. Remove the directly connected DVD or flash device (or remotely connected iLO virtual DVD or flash device) from the server. Restoring the system with Windows Recovery Environment 127...

  • Page 128: Support And Other Resources

    HP X5000 G2 Network Storage System Release Notes To locate the storage system documents, go to http://www.hp.com/go/X5000-G2, and then click the support link. You can also find these documents from the Manuals page of the HP Business Support Center website: http://www.hp.com/support/manuals...

  • Page 129: Rack Stability

    Rack stability Rack stability protects personnel and equipment. WARNING! To reduce the risk of personal injury or damage to equipment: Extend leveling jacks to the floor. Ensure that the full weight of the rack rests on the leveling jacks. Install stabilizing feet on the rack. In multiple-rack installations, fasten racks together securely.

  • Page 130: Documentation Feedback

    9 Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (docsfeedback@hp.com). Include the document title and part number, version number, or the URL when submitting your feedback.

  • Page 131: A Managing The Emu

    A Managing the EMU This chapter describes how to manage the EMU using the CLI or the Enclosure Manager physical interface. CLI reference The CLI is the primary interface for managing the Enclosure Manager and is accessed via secure shell protocol over the LAN. Using the CLI is necessary for functions not possible through any other mechanism or interface.

  • Page 132: Authentication

    Authentication This section defines EM authentication CLI functions. ADD USER Syntax ADD USER "<user name>"["<password>"] Description Adds a user to the system. If you do not provide a password, you are prompted for one. If script mode is enabled and the password is not provided, the password is assigned an unmatched string. This unmatched string requires an enclosure administrator to change the password to allow the new user to access the system.
  • Page 133 above format with username:password@host. The authorized keys file must contain only protocol version 2 public keys. Each line of the file represents one key (empty lines and lines starting with # represent comments). Each protocol version 2 key consists of the following fields, separated by spaces: keytype, base64 encoded key, comment.
  • Page 134 SET USER PASSWORD Syntax SET USER PASSWORD "<user name>"["<new password>"] Description Sets a user’s password. If you do not supply a password on the command line, you are prompted to enter it. Restrictions Only the Administrator account can modify the password of the Administrator account. The <user name>...

  • Page 135: Time Functions

    Restrictions None ADD SSHKEY Syntax ADD SSHKEY <end marker><newline><certificate><newline><end marker> Description Adds an SSH key on the command line. Start with a string that does not appear within the certificate (end marker). Next, paste in the certificate. Terminate the command with the end marker. Failure to give a proper end marker before and after the certificate may cause the interface to wait for the appropriate end marker indefinitely.
  • Page 136 Table 17 Universal time zone settings (continued) Etc/GMT-3 Etc/GMT+8 Etc/Greenwich Navajo Etc/GMT+3 Etc/GMT-9 Etc/UCT PST8PDT EST5EDT Etc/GMT-4 Etc/GMT+9 Etc/Universal Etc/GMT Etc/GMT+4 Etc/GMT- 1 0 Etc/UTC Universal Etc/GMT0 Etc/GMT-5 Etc/GMT+10 Etc/Zulu Etc/GMT-0 Etc/GMT+5 Etc/GMT- 1 1 Etc/GMT+0 Etc/GMT-6 Etc/GMT+1 1 Greenwich Etc/GMT- 1 Etc/GMT+6 Etc/GMT- 1 2...
  • Page 137 DISABLE NTP Syntax DISABLE NTP Description Disables the synchronizing of time and date with a remote server using the NTP protocol. Does not clear any NTP servers that have been configured with SET NTP. Restrictions None CLEAR NTP Syntax CLEAR NTP {PRIMARY | SECONDARY } Description Clears the Primary or Secondary NTP server IP address.

  • Page 138: Inventory And Status

    SET NTP SECONDARY Syntax SET NTP SECONDARY <host> Description Sets the secondary server used for synchronizing time/date using the Network Time Protocol (NTP). <host> can be either an IPv4 address, and IPv6 address or a DNS name. Restrictions IPv4 addresses must be in the form ###.###.###.###, where each ### ranges from 0 to 255.

  • Page 139: Show Date

    Restrictions None SHOW CSR CSR-ID Syntax SHOW CSR CSR-<ID#> Description Displays the CSR event messages captured in the Enclosure Manager system log (syslog) for the specified CSR ID. The output includes the cause and action for each event message. Restrictions A valid ID for CSR-<ID#>...
  • Page 140 SHOW DEVICE SERIAL_NUMBER BLADE Syntax SHOW DEVICE SERIAL_NUMBER BLADE <bay#> Description Displays the serial number of the blade specified by the bay <bay#>. Restrictions Can be used only when the enclosure power is on, the blade is present, and iLO is communicating with the EMU properly.
  • Page 141 Restrictions The <fan number> must be 1 or 2. Fan information is not available if fan status is Dormant (meaning not powered). The EM is only directly controlling FAN 1. The JBOD IE expanders control FAN 2 so information on FAN 2 can only be reported if the enclosure power is on AND at least one SAS IO module is present and functioning normally.
  • Page 142 SHOW FRU Description Displays summary information on field replaceable units (FRUs) within the enclosure. Information provided in this section can quickly aid the administrator in contacting HP Customer Service for troubleshooting, repair, and ordering replacements. Restrictions Only displays known/live data.

  • Page 143: Internet Control

    Description Shows information for the IO modules within the enclosure: SAS, LOM, MEZZ, and PCIe. Restrictions Should be used only when enclosure power is on. If enclosure power has never been turned on, no information is available. If it was on but is now off, only the firmware version of the IO modules that have firmware is shown.
  • Page 144 REMOVE EBIPA Syntax REMOVE EBIPA { SERVER } DNS <ip address> Description Removes an EBIPA (Enclosure Bay IP Addressing) DNS server IP address from the list of DNS servers for server bays. Restrictions <ip address> must be in the form ###.###.###.###, where each ### ranges from 0 to 255. SET EBIPA Syntax SET EBIPA { SERVER } { NETMASK <netmask>...

  • Page 145: Show Network

    PING Syntax PING IPV6 [<NUMBER>] {<ipv6 address> | "<server name>"} Description Sends ICMP echo messages to a remote IPv6 device. If you omit <NUMBER>, or use a number larger than 9999 or one that is negative, then only four packets are sent. Packets are sent at one-second intervals to prevent congestion.

  • Page 146: Server Management

    Restrictions None SHOW EBIPA Syntax SHOW EBIPA Description Displays EBIPA configuration information. Restrictions EM EBIPA control only functions for the two iLO processors in the server blades. Server management Use the commands in this section to perform server management operations. POWEROFF SERVER Syntax POWEROFF SERVER { ALL | <bay#>[{ , | - } <bay#>]} [FORCE]...
  • Page 147 REBOOT SERVER Syntax REBOOT SERVER { ALL | <bay#> [{ , | - } <bay#>]} [FORCE] [{NORMAL | PXE | HDD | RBSU }] Description Sends an asynchronous request to the server to do a graceful shutdown of the OS. After the OS has had sufficient time to perform a graceful shutdown, the server blade is power cycled.
  • Page 148 SHOW SERVER NAMES Syntax SHOW SERVER NAMES Description Displays a brief description of all server blades. Restrictions This command functions only if the enclosure power is already on. If power is not on, the command responds with the message: “enclosure power is off”. If power is coming on but state exchange between iLO and EM have not normalized, some displayed information might display [Unknown] or ?.

  • Page 149: Enclosure Control

    Restrictions This command functions only if the enclosure power is already on. Because the EMU hardware cannot determine if a blade is physically present unless enclosure power is on, the EM reports the warning “enclosure power is off” if this command is issued when power is off. SHOW SERVER STATUS Syntax SHOW SERVER STATUS { ALL | <bay#>[ { , | - } <bay#>] }...
  • Page 150 POWEROFF ENCLOSURE Syntax POWEROFF ENCLOSURE Description The EM removes main DC power from the enclosure (just as if the user had pressed the enclosure power-button. Servers are NOT automatically sent a graceful shutdown command; that should be done prior to issuing this command using POWEROFF SERVER. Except when in script mode, the user is prompted for an explicit confirmation, which must be given, or the command is terminated.
  • Page 151 Restrictions <EM name> must be 1 to 32 characters long and includes all alphanumeric, underscore (_) , and hyphen (-) characters. SET ENCLOSURE ASSET Syntax SET ENCLOSURE ASSET [TAG] "<asset tag>" Description Sets the enclosure asset tag that is stored persistently in the EM, displayed with SHOW ENCLOSURE INFO command.
  • Page 152 Description Sets the blue enclosure UID. The enclosure has a UID on both the front and rear of the enclosure. However, the front UID is only lit when enclosure power is on, while the rear UID is only lit when standby power is on.

  • Page 153: Forensic

    Restrictions <URL>should be formatted as: protocol://host/path/filename. Host is a fully qualified domain name or an IPv4 address. path/filename is the pathname of the file to download. Use FORCE to allow downgrading firmware even if settings/passwords may be lost. Forensic The following set of forensically useful functions is supported by the EM CLI. CLEAR SYSLOG Syntax CLEAR SYSLOG [ EM | ENCLOSURE ]...
  • Page 154 SHOW SYSLOG SETTINGS Syntax SHOW SYSLOG SETTINGS Description Displays the remote syslog settings (enabled/disabled status, IP address, Port#) for the Enclosure Manager. Restrictions None TEST SYSLOG Syntax TEST SYSLOG Description Tests the remote system log settings by logging a test message to the remote syslog. The test message also appears in the local EM system log.

  • Page 155: Session

    ENABLE SYSLOG REMOTE Syntax ENABLE SYSLOG REMOTE Description Enables remote system logging. Restrictions The remote system log server address must be configured before enabling remote system logging. DISABLE SYSLOG REMOTE Syntax DISABLE SYSLOG REMOTE Description Disables remote system logging. Restrictions None Session Interacting with the EM via the CLI requires a login-initiated session.
  • Page 156 the EM reports the warning “The blade is not present.” if this command is issued when enclosure power is off. EXIT Syntax EXIT | LOGOUT | QUIT Description Exit the Command Line Interpreter. Restrictions None HELP Syntax HELP [<command>] Description Show Help messages for or list the top-level commands if no arguments are provided.

  • Page 157: Using The Enclosure Manager Physical Interface

    Restrictions None SET SESSION TIMEOUT Syntax SET SESSION TIMEOUT <timeout> Description Sets the number of minutes before insessions are removed. Valid session timeout. Please note: If the session timeout value is lowered, currently insessions may be removed. The default timeout is 1,440 minutes.

  • Page 158: Activate Button Menu

    Manual button functions IMPORTANT: Use the following manual button functions only with the assistance of HP Technical Support. The two manual buttons and a two-digit LED display on the EM provide basic management functions when the EM is not connected to the network.

  • Page 159: Recover Lost Password (Fp)

    Press the UP button until the display changes from “_ _“ to “Fd”. Press and hold the UP button for three seconds. The EM blinks (or flashes) “Fd” three times to acknowledge the selection. Release the UP button. The system stops flashing the pattern, internally restores all configurations to factory defaults, and reboots the EM.

  • Page 160: Exit Button Menu

    Enter the menu mode using the “Activate Button Menu” (page 158). Press the UP button until the display changes from “_ _“ to “IP”. Press and hold the UP button for three seconds. The EM displays “IP” to acknowledge the selection. Release the UP button.

  • Page 161: B Regulatory Compliance Notices

    B Regulatory compliance notices This section contains regulatory notices for the HP ______________________. Regulatory compliance identification numbers For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number. The regulatory model number can be found on the product nameplate label, along with all required approval markings and information.

  • Page 162: Modification

    This compliance is indicated by the following conformity marking placed on the product: This marking is valid for non-Telecom products and EU harmonized Telecom products (e.g., Bluetooth). Certificates can be obtained from http://www.hp.com/go/certificates. Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, Germany 162 Regulatory compliance notices...

  • Page 163: Japanese Notices

    Japanese notices Japanese VCCI-A notice Japanese VCCI-B notice Japanese VCCI marking Japanese power cord statement Korean notices Class A equipment Class B equipment Japanese notices 163...

  • Page 164: Taiwanese Notices

    Taiwanese notices BSMI Class A notice Taiwan battery recycle statement Vietnamese notice 164 Regulatory compliance notices...

  • Page 165: Laser Compliance Notices

    Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein. Allow only HP Authorized Service technicians to repair the unit. The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented regulations for laser products on August 2, 1976.

  • Page 166: German Laser Notice

    German laser notice Italian laser notice Japanese laser notice 166 Regulatory compliance notices...

  • Page 167: Spanish Laser Notice

    Spanish laser notice Recycling notices English recycling notice Disposal of waste equipment by users in private household in the European Union This symbol means do not dispose of your product with your other household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment.

  • Page 168: Bulgarian Recycling Notice

    Bulgarian recycling notice Изхвърляне на отпадъчно оборудване от потребители в частни домакинства в Европейския съюз Този символ върху продукта или опаковката му показва, че продуктът не трябва да се изхвърля заедно с другите битови отпадъци. Вместо това, трябва да предпазите човешкото здраве и околната среда, като...

  • Page 169: Estonian Recycling Notice

    Estonian recycling notice Äravisatavate seadmete likvideerimine Euroopa Liidu eramajapidamistes See märk näitab, et seadet ei tohi visata olmeprügi hulka. Inimeste tervise ja keskkonna säästmise nimel tuleb äravisatav toode tuua elektriliste ja elektrooniliste seadmete käitlemisega egelevasse kogumispunkti. Küsimuste korral pöörduge kohaliku prügikäitlusettevõtte poole. Finnish recycling notice Kotitalousjätteiden hävittäminen Euroopan unionin alueella Tämä...

  • Page 170: Greek Recycling Notice

    Greek recycling notice Απόρριψη άχρηοτου εξοπλισμού από ιδιώτες χρήστες στην Ευρωπαϊκή Ένωση Αυτό το σύμβολο σημαίνει ότι δεν πρέπει να απορρίψετε το προϊόν με τα λοιπά οικιακά απορρίμματα. Αντίθετα, πρέπει να προστατέψετε την ανθρώπινη υγεία και το περιβάλλον παραδίδοντας τον άχρηστο εξοπλισμό...

  • Page 171: Lithuanian Recycling Notice

    Lithuanian recycling notice Nolietotu iekārtu iznīcināšanas noteikumi lietotājiem Eiropas Savienības privātajās mājsaimniecībās Šis simbols norāda, ka ierīci nedrīkst utilizēt kopā ar citiem mājsaimniecības atkritumiem. Jums jārūpējas par cilvēku veselības un vides aizsardzību, nododot lietoto aprīkojumu otrreizējai pārstrādei īpašā lietotu elektrisko un elektronisko ierīču savākšanas punktā. Lai iegūtu plašāku informāciju, lūdzu, sazinieties ar savu mājsaimniecības atkritumu likvidēšanas dienestu.

  • Page 172: Slovak Recycling Notice

    Slovak recycling notice Likvidácia vyradených zariadení používateľmi v domácnostiach v Európskej únii Tento symbol znamená, že tento produkt sa nemá likvidovať s ostatným domovým odpadom. Namiesto toho by ste mali chrániť ľudské zdravie a životné prostredie odovzdaním odpadového zariadenia na zbernom mieste, ktoré...

  • Page 173: Battery Replacement Notices

    Battery replacement notices Dutch battery notice French battery notice Battery replacement notices 173...

  • Page 174: German Battery Notice

    German battery notice Italian battery notice Regulatory compliance notices...

  • Page 175: Japanese Battery Notice

    Japanese battery notice Spanish battery notice Battery replacement notices 175...

  • Page 176: Glossary

    Glossary Customer self repair. EBIPA Enclosure Bay IP Addressing Enclosure Manager Enclosure Manager Unit Electrostatic discharge. The emission of a potentially harmful static electric voltage as a result of improper grounding. Field replaceable unit. An assembly component that is designed to be replaced on site, without the system having to be returned to the manufacturer for repair.

  • Page 177: Index

    Insight Remote Support, implementing, installing X5000 G2 hardware, electrostatic discharge avoiding, Japanese notices, CLI reference, configuring management processor, LED behavior, kit contents logging in, X5000 G2 Network Storage System, removing and replacing, Korean notices, using CLI SHOW commands for troubleshooting, enclosure rails...
  • Page 178 laser compliance notices, rack rails removing and replacing, 2-port 1 GB Ethernet I/O module, Rack stability 2-port 1 GB Ethernet, Mezz A and B I/O module, cache module controller, recovering the system, chassis switches and indicator, system recovery DVD, EMU, USB flash drive, fan, recycling notices,...
  • Page 179 System Manager, SAS I/O module removing and replacing, serial number unpacking the X5000 G2 Network Storage System, locating, updating server airflow baffle system software and firmware, removing and replacing, upgrading server blade system software and firmware, LED behavior,...

Table of Contents