Genicom GEK 00031B Programmer's Manual page 313

Set Horizontal Pitch <DECSHORP>................. 219
Set Horizontal Spacing <SHS> ......................... 244
Set Horizontal Tab Stops <DECSHTS>............ 220
Set Left and Right Margins <DECSLRM> ....... 222
Set Lines per Physical Page <DECSLPP> ........ 221
Set Top and Bottom Margins <DECSTBM>..... 223
Set Vertical Pitch <DECVERP> ....................... 228
Set Vertical Spacing <SVS>.............................. 248
Set Vertical Tab Stops <DECSVTS> ................ 226
Soft Terminal Reset <DECSTR> ...................... 225
Spacing Pitch Increment <SPI>......................... 246
Tab Clear <TBC> .............................................. 249
Vertical Position Absolute <VPA> ................... 249
Vertical Position Backward <VPB>.................. 250
Vertical Position Relative <VPR>..................... 250
Vertical Tab Set <DECVTS> ............................ 229
Control characters
<CSI> Control sequence introducer .................. 201
<DCS> Printer control string............................. 201
<EPA> End of protected area............................ 201
<ESA> End of selected area .............................. 201
<HTS> Horizontal tab set.................................. 202
<IND> Index ..................................................... 202
<NEL> Next line ............................................... 202
<PLD> Partial line down................................... 202
<PLU> Partial line up........................................ 202
<RI> Reverse index........................................... 202
<SS2> Single shift 2.......................................... 202
<SS3> Single shift 3.......................................... 202
<ST> String terminator...................................... 202
<VTS> Vertical tab set...................................... 202
Control codes ......................................................... 199
<BEL> Bell ....................................................... 199
<BS> Backspace................................................ 199
<CAN> Cancel .................................................. 199
<CR> Carriage return ........................................ 199
<ESC> Escape................................................... 199
<FF> Form feed................................................. 199
<HT> Horizontal tab ......................................... 200
<LF> Line feed.................................................. 200
<SI> Shift in ...................................................... 200
<SO> Shift out .................................................. 200
<SUB> Substitute.............................................. 200
<VT> Vertical tab ............................................. 200
Horizontal advance increments .............................. 254
Page coordinate system.......................................... 251
Character cell model.......................................... 252
Origin and extent ............................................... 252
Point model ....................................................... 252
Positioning and movement ................................ 253
Printable characters................................................ 198
Sixes graphics ........................................................ 256
printer emulation ............................................................ 8
Printronix 300/600 ....................................................... 66
Printronix P300/600
Control Codes .......................................................... 66
<ACK> Line at 8lpi............................................. 66
<BS> Elongated Character Line.......................... 66
<CR> Carriage Return Slew Zero or Edit Mode . 66
<DC1> Ready/Select ........................................... 66
<DC3> Busy/Select ............................................. 67
<DLE> High vertical density graphics ................ 67
GEK-00029B
<ENQ> Normal density plot line .........................67
<EOT> High density plot line..............................67
<ETX> End of transmission ................................67
<FF> Form Feed ..................................................67
<HT> Horizontal Tab ..........................................67
<LF> Line Feed ...................................................67
<RS> Record Separator .......................................67
<SI> Shift In ........................................................68
<SO> Shift Out ....................................................68
<SP> Space..........................................................68
<UNDL> Underline.............................................68
<US> Unit Separator ...........................................68
<VT> Vertical Tab...............................................68
Bell code <BEL> .................................................66
Control Codes<DEL> Delete ...................................67
Electronic Vertical Format Unit ...............................72
Graphics ...................................................................69
Dot Patterns .........................................................70
Dot Patterns and Densities ...................................69
Printronix P300/600 Emulation Options Table...........274
Printronix Pseries Emulation Options Table...............274
Proprinter
Command Directory...............................................111
Commands
<HT> Horizontal Tab ........................................110
Automatic line feed............................................114
Deselect printer ..................................................117
Double strike print, start ....................................115
Double wide print, on/off...................................118
Emphasized print, start.......................................115
Emphasized print, stop.......................................115
Form length in inches, set ..................................115
Graphics, high-speed double density, set ...........120
Graphics, low speed double density, set.............120
Graphics, quadruple density, set ........................121
Graphics, set normal density..............................120
Horizontal margins, set ......................................118
Horizontal tab stops, set.....................................115
Overscore ...........................................................112
Print continuously from all character chart ........112
Print mode, select...............................................116
Print single character from all character chart....112
Proportional spacing, set ....................................117
Select character set 1..........................................114
Select character set 2..........................................114
Select code page.................................................113
Set 12 cpi ...........................................................112
Set 7/72 line spacing ..........................................113
Set 8 lpi..............................................................113
Set form length in lines ......................................115
Set graphics line spacing....................................114
Set top of form ...................................................114
Skip perforation, cancel .....................................116
Skip perforation, set ...........................................116
Start text line spacing.........................................113
Store 7/72 line spacing.......................................114
Superscript / Subscript, reset..............................117
Superscript / Subscript, Set ................................117
Tabs, power on settings, set all ..........................117
Underscore.........................................................112
Unidirectional printing, set ................................117
Variable line feed...............................................116
313
5000 Series Programmer's Manual