Turning Outputs On/Off; 12. Reset Latching Outputs; Telco Arm/Disarm Sequence (Call Forward On/Off); Telco Arm Sequence - Bosch ICP-CC488 User Manual

ICP-CC488 | User's Guide | 11.
3. Press the [#] button to exit and return to the
disarmed state.
Two beeps sound, and the STAY and AWAY
indicators turn off. If a long beep sounds, an
error was made when entering the date and time.
11.

Turning Outputs On/Off

This feature is only applicable if your installer set up
an output that can be turned on or off by the
codepad. The output programmed by your installer
can control a pool pump or outside lighting. Up to
three separate outputs can be programmed.
How to Turn an Output On or Off
1. Enter your four character Master Code, followed
by [5] and the [#] key (for example, [25805#]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the output number (1 to 3).
3. Press the [#] key to turn the output on, or press
the [*] key to turn the output off.
Three beeps sound if the output is turned on,
and two beeps sound if the output is turned off.
Repeat Step 2 and Step 3 if more than one output
is required to be turned on or off.
4. Press the [#] key to exit from this function.
Two beeps sound and the STAY and AWAY
indicators turn off.

12. Reset Latching Outputs

This feature is only applicable if your installer
programmed an output to latch (remain on) until you
acknowledge the event that occurred.
How to Reset Latching Outputs
Hold down the [7] key until two beeps sound.
The output resets.
13. Telco Arm/Disarm
Sequence (Call Forward
On/Off)
Use this feature to program the Telco Arm Sequence
and Telco Disarm Sequence.
13.1

Telco Arm Sequence

Use to program the Call Forward – Immediate On
sequence or Call Forward – No Answer sequence to
automatically operate when you arm the system in
the AWAY Mode. This feature is only available if
your telecommunications provider has the call-
forward option available.
The examples given in this feature are
only applicable to Australia.
Bosch Security Systems, Inc. | 12/08 | F01U089456-02
Turning Outputs On/Off
Call Forward – Immediate On
You can redirect calls to anywhere in Australia,
including mobile phones, pagers, and answering
services. When Call Forward is turned on, your
telephone does not ring.
Call Forward – No Answer
When your telephone is not answered within 20 sec,
this feature redirects all incoming calls to another
number anywhere in Australia. You can still make
outgoing calls.
How to Program the Telco Arm Sequence
1. Enter your four character Master Code, followed
by the [3] and [#] keys (for example, [25803#]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Press the [1] key followed by the [#] key to select
the Telco Arm Sequence. Three beeps sound.
3. Enter the Call Forward Sequence (for example,
[*61][Phone Number][#] to program the Call
Forward - No Answer Sequence or [*21][Phone
Number][#] to program the Call Forward
Immediate Sequence).
To program an "*" in the Telco Arm Sequence,
enter [*1], and to program a "#" in the Telco
Arm Sequence, enter [*2].
4. Press the [#] key when finished.
Two beeps sound, and the STAY and AWAY
indicators turn off.
13.2
Use this function to automatically disable the call
forward sequence upon disarming the system.
How to Program the Telco Disarm Sequence
1. Enter your four-character Master Code, followed
by the [3] and [#] keys (for example, [25803#]).
Three beeps sound, and the STAY and AWAY
indicators flash.
2. Press the [2] key followed by the [#] key to select
the Telco Disarm Sequence. Three beeps sound.
3. Enter the Call Forward Disable Sequence (for
example, [#61#] to disable the No Answer Call
Forward sequence, or [#21#] to disable the Call
Forward Immediate Sequence).
4. Press the [#] key when finished.
Two beeps sound, and the STAY and AWAY
indicators turn off.
To disable the Telco Arm Sequence,
enter the Call Forward Sequence as [*4]
(break) for Step 3.

Telco Disarm Sequence

To program a "#" in the Telco Disarm
Sequence, enter [*2].
EN | 14