Canon imageRUNNER ADVANCE 715iF III Series Service Manual page 352

No.*1 No.*2
##114 ##3114
##116 ##3116
##200 ##3200
##201 ##3201
##204 ##3204
##220 ##3220
##223 ##3223
##224 ##3224
##226 ##3226
##227 ##3227
##229 ##3229
##230 ##3230
##231 ##3231
##232 ##3232
##237 ##3237
##238 ##3238
##261 ##3261
##280 ##3280
##281 ##3281
##282 ##3282
##283 ##3283
##284 ##3284
##285 ##3285
##286 ##3286
##287 ##3287
##288 ##3288
##289 ##3289
##290 ##3290
##670 ##3670
##671 ##3671
##672 ##3672
##673 ##3673
##674 ##3674
##675 ##3675
##750 ##3750
##752 ##3752
##753 ##3753
##754 ##3754
T/R
[R] at time of reception, RTN is transmitted.
[T/R] Disconnection of loop current was detected during communication.
[R] at time of reception, no image carrier is detected for 5 sec.
[T/R] DCN is received outside the normal parity procedure.
[T] DTC without transmission data is received.
[T/R] system error (main program out of control) has occurred.
[T/R] while a communication is under way, the line is cut.
[T/R] in communication, an error has occurred in the procedural signal.
[T/R] the stack printer has fallen outside the RAM area.
[R] An attempt was made to record a file without image.
[R] the recording unit has remained locked for 1 min.
[T/R] A unit for controlling the display has malfunctioned.
[T/R] A unit for controlling the Control Panel buttons has malfunctioned.
[T] encoding error has occurred.
[R] decoding error has occurred.
[R] the print control unit is out of order.
[T/R] system error has occurred.
[T] at time of transmission, the procedural signal has been transmitted more than speci-
fied.
[T] at time of transmission, the procedural signal has been transmitted more than speci-
fied.
[T] at time of transmission, the procedural signal has been transmitted more than speci-
fied.
[T] at time of transmission, the procedural signal has been transmitted more than speci-
fied.
[T] at time of transmission, DCN is received after transmission of TCF.
[T] at time of transmission, DCN is received after transmission of EOP.
[T] at time of transmission, DCN is received after transmission of EOM.
[T] at time of transmission DCN is received after transmission of MPS.
[T] after transmission of EOP, a signal other than PIN, PIP, MCF, RTP, or RTN has been
received.
[T] after transmission of EOM, a signal other than PIN, PIP, MCF, RTP, or RTN has been
received.
[T] after transmission of MPS, a signal other than PIN, PIP, MCF, RTP, or RTN has been
received.
[T] at time of V.8 late start, the V.8 ability of DIS front the receiving party is expected to
be detected, and the CI signal is expected to be transmitted in response; however,
the procedure fails to advance, and the line is released because of T1 time-out.
[R] at time of V.8 arrival, procedure fails to move to phase 2 after detection of CM signal
from caller, causing T1 time-out and releasing line.
[T] at time of V.34 transmission, a shift in procedure from phase 2 to phase 3 and there-
after stops, causing the machine to release the line and suffer T1 timeout.
[R] at time of V.34 reception, a shift in procedure from phase 2 to phase 3 and thereafter
stops, causing the machine to release the line and suffer T1 timeout.
[T] at time of V.34 transmission, a shift in procedure from phase 3 and phase 4 to the
control channel and thereafter stops, causing the machine to release the line and
suffer T1 timeout.
[R] at time of V.34 reception, a shift in procedure from phase 3 and phase 4 to the control
channel and thereafter stops, causing the machine to release the line and suffer T1
timeout.
[T] at time of ECM transmission, no meaningful signal is received after transmission of
PPS-NULL, causing the procedural signal to be transmitted more than specified.
[T] at time of ECM transmission, DCN is received after transmission of PPS-NULL.
[T] at time of ECM transmission, the procedural signal has been transmitted more than
specified after transmission of PPS-NULL, or T5 time-out (60 sec) has occurred.
[T] at time of ECM transmission, the procedural signal has been transmitted more than
specified after transmission of PPS-NULL.
Description
341
7. Error/Jam/Alarm