Table Of Contents - Key Automation LEV3301L Instructions And Warnings For Installation And Use

TABLE OF CONTENTS

1
Safety warnings
2
Product introduction
2.1 Product description
2.2 Technical specifications
2.3 Wiring table
2.4 Mounting surface materials
2.5 Assembly equipment
2.6 Safety distances
2.7 Hazards and risks
3
Preliminary Checks
4
Installation dimensions
4.1 Commercial profile installation dimensions - Side View
4.2 Dimensions of installation with glass panels - Side View
4.3 Installation with breakout profile
5
Fixing instructions
5.1 Locking
5.2 Inserting the track on the beam
5.3 Double panel installation dimensions - Top and front view
5.4 Installation dimensions of single panel version with
opening to the right - Top and front view
5.5 Installation dimensions for single panel version with
opening to the left - Top and front view
6
Panel preparation
6.1 Detail of the runner
6.2 Assembly of the runners on the panel with lowered
adapter profile
6.3 Fixing of the runner on the adapter profile
6.4 Inserting the panel on the beam
6.5 Fastening the guide to the floor and sliding runner
7
Positioning and wiring the modules
7.1 Positioning of the modules inside the beam
7.2 Wiring of the modules inside the beam
7.3 Connection of the panel to the transmission belt
7.4 Tensioning the belt
7.5 Adjusting the limit switches
7.6 Wiring of the door to the line
8
Installation of protection panels
8.1 Assembly of lateral compartments
8.2 Recessed wall beam
8.3 Cover panel preparation
8.4 Locking the cover panel
9
pag. 38 Control unit
9.1 The board
9.2 CTLEV control equipment
pag. 40
9.3 Example of sensor connection
pag. 40
9.4 Example of sensor connection conforming to EN16005
pag. 40
9.5 Example of PA025CT and PA014IR connection
pag. 40
9.6 Example of PA025CT and PA014IR monitored connection
pag. 41
Example of SMNPAE manual selector connection
9.7
pag. 41
9.8 Example of SEL1 and SEL2 connection
pag. 41
9.9 Example of SEL4 selector connection
pag. 42
9.10 Example of SEL5 selector connection
9.11 First start-up
Power on
9.12
pag. 42
10
Operating mode
pag. 43
10.1 The operating modes
pag. 43
10.2 Learning procedure
pag. 44
10.3 Deceleration space self-test procedure
pag. 44
10.4 Bidirectional mode
10.5 Output Mode
pag. 45
10.6 Input Mode
pag. 45
10.7 Partial Opening Mode
pag. 45
10.8 Open Mode
pag. 46
10.9 Block Mode
10.10 Pharmacy Mode
pag. 47
10.11 Open and Close Commands
10.12 Start Command
pag. 48
10.13 Stop Command
Photo Command
10.14
10.15 Emergency opening command
pag. 49
10.16 RALL Photo command
pag. 49
10.17 Battery
10.18 No mains power supply
pag. 49
10.19 Interlock
pag. 49
10.20 Displays
pag. 50
pag. 50
11
Menu
11.1 Parameter modification procedure
pag. 51
11.2 Obstacle detection
pag. 51
11.3 Safety devices monitored
pag. 51
11.4 Settings with special codes
pag. 52
11.5 Examples of error codes
pag. 52
pag. 53
12
pag. 53
Maintenance plan
13
pag. 53
Testing and commissioning
pag. 53
13.1 Testing
pag. 54
13.2 Commissioning
pag. 54
pag. 55
EN
pag. 56
pag. 56
pag. 57
pag. 58
pag. 59
pag. 60
pag. 60
pag. 61
pag. 61
pag. 62
pag. 62
pag. 62
pag. 63
pag. 63
pag. 63
pag. 63
pag. 63
pag. 63
pag. 64
pag. 64
pag. 64
pag. 64
pag. 64
pag. 64
pag. 64
pag. 64
pag. 64
pag. 64
pag. 65
pag. 65
pag. 65
pag. 65
pag. 65
pag. 66
pag. 67
pag. 67
pag. 68
pag. 68
pag. 68
pag. 69
pag. 70
pag. 71
pag. 71
pag. 71
37