Omron K7DD User Manual page 137

Variable
address
H'0400 Trigger Mode *1
H'0401 Trigger Type *1
H'0402 Internal Trigger Source
H'0403 to Reserved
H'04FF
H'0500 Baud Rate 1
H'0501 Parity 1
H'0502 Send Wait Time 1
H'0503 Baud Rate 2
H'0504 Parity 2
H'0505 Send Wait Time 2
H'0506 to Reserved
H'05FF
H'0600 Monitored Feature [0] Alarm Type
H'0601 Monitored Feature [1] Alarm Type
: :
H'068D Monitored Feature [141] Alarm Type
H'068E to Reserved
H'06FF
*1 When selecting External (H'0001) as the trigger mode and Level (H'0002) as the trigger type, set the feature
calculation cycle to the default value (H'0001: 1). Otherwise, correct measurement may not be achieved.
Power Line Data Generator User's Manual (N233)
Variable name
This is a setting parameter. Set the mode of the trigger.
H'0000: Continuous (default value), H'0001: External,
H'0002: Internal
This is a setting parameter. Set the type of the trigger.
H'0000: Rising (default value), H'0001: Falling, H'0002:
Level
This is a setting parameter. Set the feature value used as
the trigger source.
H'0000: Ch1 R.M.S. Voltage (default value)
H'0001: Ch2 R.M.S. Voltage
H'0002: Ch3 R.M.S. Voltage
H'0003: Ch1 R.M.S. Current
H'0004: Ch2 R.M.S. Current
H'0005: Ch3 R.M.S. Current
H'0006: Ch1 Frequency
H'0007: Reserved
H'0008: Reserved
H'0009: Active Power
H'000A: Power Factor
Do not access.
This is a setting parameter. Set the baud rate of the
communications terminal 1.
H'0000: 9.6 k, H'0001: 19.2 k, H'0002: 38.4 k, H'0003:
57.6 k, H'0004: 115.2 k (default value), H'0005: 230.4 kbps
This is a setting parameter. Set the parity of the
communications terminal 1.
H'0000: None, H'0001: Even (default value), H'0002: Odd
This is a setting parameter. Set the send wait time of the
communications terminal 1.
H'0000 to H'0063 (0 to 99 ms), Default value: H'0014
(20 ms)
This is a setting parameter. Set the baud rate of the
communications terminal 2.
H'0000: 9.6 k, H'0001: 19.2 k, H'0002: 38.4 k, H'0003:
57.6 k, H'0004: 115.2 k (default value), H'0005: 230.4 kbps
This is a setting parameter. Set the parity of the
communications terminal 2.
H'0000: None, H'0001: Even (default value), H'0002: Odd
This is a setting parameter. Set the send wait time of the
communications terminal 2.
H'0000 to H'0063 (0 to 99 ms), Default value: H'0014
(20 ms)
Do not access.
This is a setting parameter. It is an alarm type set for each
of the feature values having 142 types of IDs.
Refer to
information on the list of feature values and IDs and the
setting ranges.
Do not access.
7 Communications
Description
6-3-1 Feature Value Range for Monitoring for
Setting
reflection
timing
After
restart
After
restart
After
restart
---
After
restart
After
restart
After
restart
7
After
restart
After
restart
After
restart
---
After
restart
---
7 - 21