Konica Minolta bizhub C658 Service Manual page 1556

bizhub C658/C558/C458/C368/C308/C258
Error code
CFCC6
CFCC7
CFCC8
CFCC9
CFCCA
CFCCB
CFCCC
CFCCD
CFCCE
CFCCF
6.14.14 CFCD# (bizhub C368/C308/C258)
Error code
CFCD0
CFCD1
CFCD2
CFCD3
CFCD4
CFCD5
CFCD6
CFCD7
CFCD8
CFCD9
CFCDA
CFCDB
CFCDC
CFCDD
CFCDE
CFCDF
6.14.15 CFCE# (bizhub C368/C308/C258)
Error code
CFCE0
CFCE1
CFCE2
A "1" is set when access is made to the JPEG core slave space of
DMA15 while the dual scan image processing board (Asic777) soft
reset is being active
A "1" is set when access is made to the comment table of DMA15
while the dual scan image processing board (Asic777) soft reset is
being active
Completer Abort exists in dual scan image processing board (Asic777)
memory master access
Unsupported Request exists in dual scan image processing board
(Asic777) memory master access
Completion Timeout exists in dual scan image processing board
(Asic777) memory master access
Poisoned TLP exists in dual scan image processing board (Asic777)
memory master access
Unsupported Request exists in dual scan image processing board
(Asic777) memory target access
Poisoned TLP exists in dual scan image processing board (Asic777)
memory target access
Unsupported Request TLP exists in dual scan image processing board
(Asic777) config target access
Poisoned TLP exists in dual scan image processing board (Asic777)
config target access
A "1" is set when a rising edge is detected of VD output from the dual
scan image processing board (Asic777) CPS
A "1" is set when a falling edge is detected of VD output from the dual
scan image processing board (Asic777) CPS
A "1" is set when a rising edge is detected of VD output from the dual
scan image processing board (Asic777) DMA03
A "1" is set when a falling edge is detected of VD output from the dual
scan image processing board (Asic777) DMA03
A "1" is set when a falling edge is detected of VSYNC input to the dual
scan image processing board (Asic777) DMA03
Dual scan image processing board (Asic777) Emepror-IP error
Dual scan image processing board (Asic777) external bus error
Dual scan image processing board (Asic777) PC delay interrupt
(INT_PCD0)
Dual scan image processing board (Asic777) PC delay interrupt
(INT_PCD1)
Dual scan image processing board (Asic777) PC delay interrupt
(INT_PCD2)
Dual scan image processing board (Asic30) image input interface had
overflow
Dual scan image processing board (Asic30) JBIG core detected
unknown marker
Dual scan image processing board (Asic30) JBIG core detected SC
count overflow
SDTMDT is accessed during dual scan image processing board
(Asic30) soft reset active
EmperorIP is accessed during dual scan image processing board
(Asic30) soft reset active
Dual scan image processing board (Asic30) SDTMDT had a timeout
error
Completer Abort exists in dual scan image processing board (Asic30)
memory master access
supported Request exists in dual scan image processing board
(Asic30) memory master access
Completion Timeout exists in dual scan image processing board
(Asic30) memory master access
Item
Item
Item
K-228
K TROUBLESHOOTING > 6. ABORT CODE
Component
Component
Dual scan image
processing board (DSIPB:
DF-704)
Component
• MFP board (MFPB)
• Dual scan image
processing board
(DSIPB: DF-704)
Rank
Rank
C
Rank
C