Page 3 Foreword This Instruction manual and its corresponding supplements should be read carefully to familiarise yourself with your vehicle. Besides the regular care and maintenance of the vehicle, its correct handling will contribute to preserve its value. For safety reasons, note the information concerning accessories, modifications and parts change. If selling the vehicle, give all of the onboard documentation to the new owner as this should be kept with the vehicle.
Page 5: Table Of Contents
Remote control keys ..... . Seat belts .......
Page 6 Contents Trailer towing Side indicators ............Luggage compartment lights .
Page 7: Manual Structure
Manual structure Manual structure What you should know before reading the on-board manual For the sake of the environment This manual contains a description of the equipment supplied with the Texts preceded by this symbol refer to relevant points concerning environ- vehicle at the time of press.
Page 8 (e.g. “Air conditioning”). The entire manual is divided into five large parts which are: 1. Safety First Information on the vehicle equipment relating to passive safety such as seat belts, airbags, seats, etc. 2. Controls and equipment Information about the distribution of controls in the driver position of your vehicle, about the seat adjustment possibilities, about how to create a suit- able climate in the passenger compartment, etc.
Page 9: Safety First
These are just a few of the safety features in your SEAT: • Three-point seat belts optimised for all seats, WARNING • Belt force limiters for the seats, •...
Page 10 There are also a number of important safety warnings that you and your passengers – Fasten your seat belt correctly. Make sure that your passengers should always observe in order to minimise the risk of injury.
Page 11 Safe driving – If possible, avoid driving when you are tired or stressed. WARNING When driving safety is impaired during a trip, the risk of injury and acci- WARNING dents increases. When driving safety is impaired during a trip, the risk of injury and acci- dents increases.
Page 12: Proper Sitting Position For Occupants
⇒ fig. and steering wheel – Move the driver's seat forwards or backwards so that you are able to press the accelerator, brake and clutch pedals to the floor with your knees still slightly angled ⇒ – Ensure that you can reach the highest point of the steering wheel.
Page 13 The airbag system and seat belts can only provide optimal protection when the back- rest is in an upright position and the driver is wearing his or her seat belt WARNING properly.
Page 14 Always keep your feet in the footwell when the vehicle is moving; never WARNING rest them on the instrument panel, out the window or on the seat. An incor- • rect sitting position exposes you to an increased risk of injury in case of a If the passengers on the rear seat are not sitting properly, they could sudden braking or an accident.
Page 15 Safe driving Correct adjustment of front seat head restraints Adjust the head restraint properly in order to achieve maximum protection. Properly adjusted head restraints are an important part of – Adjust the head restraint so that its upper edge is at the same...
Page 16 Under no circumstances should the rear passengers travel while the head restraints are in the non-use position. • Do not swap the centre rear head restraint with either of the outer seat rear head restraints. • Injury risk in case of an accident! Caution Note the instructions on the adjustment of the head restraints ⇒...
Page 17: Pedal Area
If a brake circuit fails, the brake pedal must be pressed down thoroughly in never put your feet on the dash panel, order to stop the vehicle. • never put your feet on the surface of a seat, • Wear suitable shoes never travel in a foot well , •...
Page 18: Stowing Luggage
Safe driving Floor mats on the driver side – Distribute the load evenly in the luggage compartment. Only floor mats may be used which can be securely fastened – Lay and stow heavy luggage as far forward as possible in the luggage compartment.
Page 19 • Never secure a child seat on the fastening rings. Fastening rings* There can be four fastening rings in the boot for fastening luggage and other objects.
Page 20: Seat Belts
WARNING • Before starting the vehicle: If seat belts are worn incorrectly or not at all, the risk of severe injuries increases. – Fasten your safety belt securely. • Properly worn seat belts can reduce severe injuries in case of sudden braking manoeuvres or accidents.
Page 21: Why Wear Seat Belts
25 km/h to 50 km/h, for example, the kinetic energy is multi- plied by four. Because the passengers in our example are not restrained by seat belts, all of the passengers' kinetic energy has to be absorbed at the point of impact ⇒...
Page 22 It is also important for the rear passengers to wear seat belts properly, as they could otherwise be thrown forward violently in an accident. Rear passengers who do not use seat belts endanger not only themselves but also the front ⇒...
Page 23 • If the seat belts are worn incorrectly or not at all, the risk of severe inju- Our examples describe frontal collisions. Of course, properly worn seat belts ries increases. The optimal protection from seat belts can be achieved only substantially reduce the risk of injury in all other types of accidents.
Page 24: Seat Belts
• Do not allow the seat belt to be damaged or jammed, or to rub on any sharp edges. • Never wear the seat belt under the arm or in any other incorrect posi- tion.
Page 25 • Never put the latch plate in the buckle of another seat. If you do this, the seat belt will not protect you properly and the risk of injury is increased.
Page 26 An incorrectly worn seat belt web can cause severe injuries in the event of an accident. • The shoulder part of the seat belt must lie on the centre of the shoulder, never across the neck. The seat belt must lie flat and snugly on the torso ⇒ page 23, fig.
Page 27 • WARNING For pregnant women, the lap part of the seat belt must lie as low as possible over the pelvis, never across the stomach, and always lie flat so Never unbuckle a seat belt while the vehicle is in motion. If you do, you that no pressure is exerted on the abdomen.
Page 28: Belt Tension Devices
Sensors will trigger the belt tension devices during severe head-on, lateral Seat belts can provide optimal protection only if the belt web is and rear collisions only if the seat belt is being worn. This retracts and properly worn. The seat belts must be fastened exactly in the order tightens the seat belts, reducing the forward motion of the occupants.
Page 29 Seat belts Service and disposal of belt tension devices The belt tension devices are components of the seat belts that are installed in the seats of your vehicle. If you work on the belt tension devices or remove and install parts of the system when performing other repair work, the seat belt may be damaged.
Page 30: Airbag System
The airbag is deployed at high speed in fractions of a second. If you have an • If you are not wearing a seat belt, if you lean forward or to the side while incorrect seating position at the time the airbag is deployed, it could cause travelling or assume an incorrect sitting position, there is a substantially you critical injuries.
Page 31 WARNING • If a child seat is secured to the front passenger seat, the risk to the child The warning lamp monitors all airbags and belt tension devices in the of sustaining critical or fatal injuries in the event of an accident increases.
Page 32 Airbag system Repairs, maintenance and disposal of the airbags Monitoring of airbag and belt tension device system Both the airbag and belt tension device systems operation is constantly monitored electronically. Each time the ignition is switched on, the warning The parts of the airbag system are installed in various places in your vehicle. ...
Page 33 Airbag system WARNING (continued) • We strongly recommend you to go to a qualified workshop for all work on the airbag system. • Never attempt to alter the front bumper or the body. • The airbags provide protection for just one accident; replace them once they have deployed.
Page 34: Front Airbags
The airbag system is not a substitute for seat belts, but it is an integral part of the vehicle's overall passive safety system. Please bear in mind that the airbag system can only work effectively when the occupants are wearing their seat belts correctly and have adjusted the head restraints properly.
Page 35 • The seat belts and airbags can only provide maximum protection if the The special design of the airbag allows the controlled escape of the propel- occupants are seated correctly ⇒...
Page 36 Airbag system may develop when the airbag deploys. This is normal and it is not an indica- tion of fire in the vehicle. Airbag covers when the frontal airbags are triggered Fig. 20 Airbag covers reacting when the front airbags are triggered The airbag covers fold out of the steering wheel or instrument panel when the ⇒...
Page 37: Knee Airbag
• If you are not wearing a seat belt, if you lean forward or to the side while travelling or assume an incorrect sitting position, there is a substantially increased risk of injury. This increased risk of injury will be further increased if you are struck by an inflating airbag.
Page 38 Airbag system The airbag system is not a substitute for your seat belts. Rather, it is part of WARNING the overall occupant restraint system in your vehicle. Always remember that • the airbag system can only help to protect you if you are wearing your safety Safety belts and the airbag system can only provide protection when belt and wearing it properly.
Page 39 All this takes place instantaneously, so fast that many people don't even belt.
Page 40: Side Airbags
The airbag system is not a substitute for seat belts, but it is an integral part Description of side airbags of the vehicle's overall passive safety system.
Page 41 Any work carried out to the doors should be made in a qualified author- ised workshop. • The seat belts and airbags can only provide maximum protection if the occupants are seated correctly ⇒ page 10, “Proper sitting position for occupants”.
Page 42 ⇒ page 46, “Child safety”. • If you do not wear a seat belt, if you lean forward, or are not seated • Any work on the side airbag system or removal and installation of the...
Page 43: Curtain Airbags
⇒ page 42, “Safety notes on the operation of the curtain airbag system”. The airbag system is not a substitute for seat belts, but it is an integral part of the vehicle's overall passive safety system. Please bear in mind that the airbag system can only work effectively when the occupants are wearing their seat belts correctly and have adjusted the head restraints properly.
Page 44 WARNING • In order for the side airbags to provide their maximum protection, the prescribed sitting position must always be maintained with seat belts fastened while travelling. • For safety reasons, the head air bag must be disconnected in those Fig.
Page 45 Airbag system WARNING (continued) should only be performed by a qualified workshop. Otherwise, faults may occur during the airbag system operation. • Do not attempt to modify components of the airbag system in any way. • The side and head airbags are managed through sensors located in the interior of the front doors.
Page 46: Deactivating Airbags
Airbag system Deactivating airbags* Disabling front passenger airbag If you fit a rear-facing child seat to the front passenger seat, the front passenger airbag must be de-activated. Fig. 28 Warning lamp for deactivated passenger airbag in centre console When the passenger airbag is deactivated, this means that only the frontal airbag is deactivated.
Page 47 • As soon as the child seat is no longer needed on the front passenger seat, enable the front passenger airbag again. • Only deactivate the passenger airbag when the ignition is off, other-...
Page 48: Child Safety
It is advisable that children always travel in the rear seats, being the rear central position the safest seat, since the risk of injuries in a side colli- – Protect your children by properly using appropriate child seats sion is diminished.
Page 49 Never allow a child to be transported in a vehicle without being properly secured, or to stand up or kneel on a seat while travelling. In an accident, the child could be flung through the vehicle, causing possibly fatal injuries to themselves and to the other passengers.
Page 50: Child Seats
Child seats that have been tested and approved under the ECE R 44 standard Group 0: For babies from about 9 months old and 10 kg in weight the most bear the test mark on the seat (the letter E in a circle with the test number ⇒ fig.
Page 51 We recommend you to include together with the on-board documentation, Children under 7 years of age weighing between 15 and 25 kg are best the manufacturer's Child Seat instructions manual. protected by group 2 child seats together with properly adjusted seat belts. Group 3 child seats WARNING Children over 7 years of age weighing between 22 and 36 kg but less than 1.5...
Page 52 The shoulder part of the seat belt must lie approximately on the centre of the shoulder, never across the neck or the arm. The seat belt must lie close to the upper part of the body. The lap belt part must lie across the pelvis, not across the stomach, and always fit closely.
Page 53: Securing Child Seats
Securing child seats Ways to secure a child seat A child seat can be secured differently on the rear seat and on the front passenger seat. • You can secure a child seat to the rear seat or front passenger seat in the Seats for children aged 0, 0+ and 1 with the “ISOFIX”...
Page 54 The Children restraint systems may be fitted with the “ISOFIX” system and/or Top Tether (placed on the luggage compart- ment cover) to the rear seat in a safe and quick way. The passenger seat* is not equipped with Top Tether and so, the “ISOFIX”...
Page 55 WARNING An undue installation of the safety seat will increase the risk of injury in the event of a crash. • Never tie the retainer strap to a hook in the luggage compartment.
Page 56 – Pull the securing belt of the child restraint according to its manu- facturer instructions for use. – Direct the Top Tether securing belt under the rear seat head ⇒ fig. 35 restraint (lift the head restraint where necessary).
Page 57 Safety First Operating instructions Practical tips Technical Data...
Page 58 Fig. 36 Some of the equipment listed in this section is only fitted on certain models or are optional extras.
Page 59 Seat memory ........
Page 60 Cockpit − Controls for radio and telephone* Adjustable steering column ......Vehicle wallet compartment / knee airbag* ....Note •...
Page 61: Instruments
Cockpit Instruments Instrument panel overview The instrument panel is the driver's information centre. Fig. 37 Overview of instrument panel Coolant temperature gauge ......Adjuster buttons for −...
Page 62: Coolant Temperature Gauge
Cockpit − Driver information system ......Normal temperature CHECK button ........In normal operations, the needle will settle somewhere in the centre of the dial once the engine has reached running temperature.
Page 63: A 2 Rev Counter Incorporating Digital Clock And Date
Cockpit Rev counter For the sake of the environment The rev counter indicates the number of engine revolutions Changing up a gear early will help you to save fuel and minimise engine noise. per minute. Digital clock and date Your vehicle is equipped with a quartz clock. Fig.
Page 64: Instrument Lighting
Cockpit Setting the minutes When the ignition is switched off, the mileage recorder and the digital clock with date display can be switched on for a few seconds by pressing the CHECK – Keep pressing the button until the minutes display MODE ⇒...
Page 65: A 4 Speedometer (Incorporating Mileage Recorder Display)
Cockpit Speedometer with distance display Fault display If there is a fault in the instrument panel, the letters DEF will permanently The speedometer indicates the speed of the vehicle and the appear in the trip recorder display. Please have the fault rectified as soon as distance travelled.
Page 66 Cockpit CHECK button Calling up driver messages If a Priority 1 symbol flashes in the display ⇒ page 75, or if the bulb monitor detects a failure of one of the lights ⇒ page 81, the relevant driver informa- tion can be called up again by briefly pressing the button.
Page 67: Warning And Indicator Lamps
 Anti-lock brake system (ABS) The warning and indicator lamps indicate a number of different functions and possible faults. ⇒ page 68  Seat belt warning ⇒ page 68  Left indicators ⇒ page 68  Electronic stabilisation programme (ESP) ⇒...
Page 68 Cockpit   Exhaust emission control system Tyre pressure monitoring display The tyre pressure should be corrected as soon as possible if If the warning lamp lights up continuously you should take your vehicle to a it is too low. specialist garage as soon as possible in order to have the fault rectified.
Page 69 Cockpit   Trailer indicators* The yellow warning lamp remains on if the system is faulty or if the pressure is too low in at least one tyre. In the event of a system This indicator lamp flashes when the indicators are operating fault, the letters TPMS are displayed in the centre of the instrument ⇒...
Page 70 The symbol driver and front passenger (if applicable) have fastened their seat belts. brake system. Please refer to ⇒ page 77. When the vehicle has reached a certain speed, you will also hear a warning signal and the warning light will flash.
Page 71 Cockpit • It will start flashing to indicate that ESP is counteracting an unstable Caution driving condition. •  If the coolant warning lamp in the instrument panel lights up as well as the It lights up when the ignition is switched on for approx. 2 seconds while alternator waning lamp while driving ⇒...
Page 72 Cockpit  Glow plug system Handbrake applied  The warning lamp also lights up when the handbrake is applied. In addi- The indicator lamp lights up while the glow plugs are tion to this, the handbrake warning ⇒ page 76 switches on after driving for 3 preheating.
Page 73: Driver Information System
Cockpit Driver information system ⇒ page 72 CD and radio display ⇒ page 72 Ambient temperature display General notes ⇒ page 73 Distance to empty (the distance you can travel with the remaining fuel) The driver information system in the instrument panel shows ⇒...
Page 74 Cockpit CD and radio display Ambient temperature display Fig. 48 Display: addi- Fig. 49 Display: Ambient tional radio information temperature display If the radio is switched on and no Priority 2 faults are indicated by the auto- The ambient temperature is shown in the display when the ignition is ⇒...
Page 75 Cockpit Door catch/ tailgate warning Note When the display shows route guidance instructions from the navigation system, the ambient temperature appears in the second line of the radio display. Fuel range The fuel range display can help you to plan your trip. The estimated fuel range is displayed in km.
Page 76: Service Indicator
Cockpit Service indicator The display reverts back to the standard display after about 5 seconds. The remaining distance to the next service is updated every time the ignition is This display reminds the driver when the next routine service switched on, until the service becomes due. is due.
Page 77: Auto-Check System
Cockpit Auto-check system Driver messages Additional messages to assist the driver are displayed Introduction together with the warning symbols in the instrument panel. The auto-check system checks important components and vehicle systems. These background checks are run constantly, as long as the ignition is switched on.
Page 78 Cockpit Red symbols Driver messages and yellow symbols If a yellow warning symbol appears in the display, it will automatically be A red symbol warns of a danger. accompanied by the corresponding driver message.  For example, the symbol is displayed to indicate that the windscreen washer fluid level is low.
Page 79 Cockpit The red symbols are used to indicate a Priority 1 fault (serious malfunction). WARNING (continued) A red symbol is accompanied by three warning chimes. The symbols will keep • If the brake warning lamp lights up together with the ABS warning flashing until the faults are corrected.
Page 80 Cockpit If the alternator warning lamp lights up as well ⇒ page 69, it is possible that Note the drive belt has broken.  The oil pressure warning lamp is not an indicator for the oil level. The oil level should therefore be checked regularly, preferably every time you fill the Caution tank.
Page 81 Cockpit  Fuel level low ⇒ page 80  Brake pad worn  When this symbol comes on for the first time, there are about 8 to 10 litres ⇒ page 80  Speed warning 1 of fuel left in the tank. You should fill up as soon as possible ⇒ page 208. ⇒...
Page 82 Cockpit  light switch. If the rain sensor is faulty, the functions operated via the wind- This symbol indicates that the self-directing headlight system is faulty. screen wiper lever will still be available. You should have the light sensor / Take the vehicle to a specialist garage to have the headlights or the self- rain sensor checked by a specialist garage as soon as possible.
Page 83: Speed Warning
Cockpit   Bulb monitor Speed warning The bulb monitor checks whether the lights on the vehicle are Introduction working. The speed warning function can help prevent you exceeding If a defective bulb is detected, or if one of the lights has failed for any reason, ...
Page 84 Cockpit  ⇒ page 81, fig. 55 Setting speed limit warning 1 The speed limit warning symbol for speed warning 1 will appear in the display if you exceed the pre-set speed. It goes out again if Use the CHECK button to set speed limit warning 1. the speed is reduced below the set speed limit.
Page 85 Cockpit with a brief push of the button, or until the memory is cleared with a long – To change the speed limit, press the top or bottom of the function ⇒ fig. push of the button. selector switch on the windscreen wiper lever 57.
Page 86: On-Board Computer
Cockpit On-board computer Single-journey memory (on-board computer 1) The single-journey memory processes the information on a journey from the time the ignition is switched on until it is switched off. If the journey is Introduction resumed within two hours after the ignition is switched off, the new figures are automatically included in the calculation.
Page 87 Cockpit Operating Driving time warning After 2 hours of continuous driving, the display automatically switches over The on-board computer is controlled by means of two to the driving time display of 2:00. At the same time the driving time display switches on the windscreen wiper lever.
Page 88: Menu Display
Cockpit • Menu display Journey duration • Distance covered • Average fuel consumption Introduction • Average speed The on-board computer can only be operated when the ignition is switched on. When the ignition is switched on, the display shows the function that was last selected.
Page 89 Cockpit Controlling the menu Some of the functions in your vehicle can be adjusted, activated and controlled via menus (e.g. tyre pressure*). With the aid of the menus you can The menu display is called up via the button and the Reset then also select the information you wish to see displayed on the DIS display.
Page 90: Tyre Pressure Monitoring
Cockpit Use the rocker switch to select the menus and adjust various values. The driven and the tyre pressure will rise accordingly. Therefore, you should only selected values are highlighted on a red background. adjust the tyre pressures when they are cold (i.e. approximately at ambient temperature).
Page 91 Cockpit  Tyre pressure monitoring display The tyre pressure should be corrected as soon as possible if it is too low.  If the symbol appears, the tyre pressure on at least one of the wheels is too low. – Stop the vehicle. –...
Page 92: The Multi-Function Steering Wheel
Steering wheel controls Steering wheel controls The multi-function steering wheel Introduction You can use the multi-function steering wheel to quickly and easily operate selected functions of the radio, CD, TV* and telephone*. Fig. 64 Driver informa- tion system The functions are operated by pressing or scrolling the controls ⇒...
Page 93 Steering wheel controls Steering wheel audio version controls (Mode) (PTT) Press Press 1st press: starts Station search. Station search. the search. No function Radio mode Increase fre- Decrease fre- Volume up Volume down 2nd press: cancels specified quency quency the search CD mode: next CD mode: previ- CD mode: fast for-...
Page 94 Steering wheel controls Steering wheel Audio + Telephone version controls (Mode) (PTT) Press Press 1st press: starts Station search. Station search. the search. No function Radio mode Increase fre- Decrease fre- Volume up Volume down 2nd press: cancels specified quency quency the search CD mode: next...
Page 95: Remote Control Keys
Unlocking and locking Unlocking and locking Remote control keys Set of keys Fig. 66 Remote control key: Release button The set of keys belonging to your vehicle consists of the following items: one remote control key. Fig. 65 Set of keys one key without remote control.
Page 96 Unlocking and locking Indicator light on the remote control key Plastic key tab Spare keys cannot be issued without the key number on the plastic key tab. The condition of the battery in the remote control key is moni- Therefore: tored by the indicator light.
Page 97 Note – Remove the used battery from the cover. • The engine can only be started using an original SEAT key with the correct – Insert the new battery. Make sure that the “+” symbol on the code. battery is facing downwards. The correct polarity is indicated on •...
Page 98: Central Locking
Unlocking and locking Central locking WARNING Do not leave anyone (especially children) inside the car if it is locked from Description the outside and the anti-theft security system is enabled, as the doors and windows cannot then be opened from the inside. Locked doors could delay The central locking system enables you to lock and unlock all assistance in an emergency, potentially putting lives at risk.
Page 99 Unlocking and locking • Unlocking the vehicle with the key The interior lights are switched off, provided the light switch is in the cour- tesy light position. • The windows and the sun roof* will close as the key is held in the locking position.
Page 100 Unlocking and locking • • The driver's door cannot be locked using the central locking system when The doors and the tailgate cannot be opened from the outside (for secu- it is still open. The door must be locked separately after it has been closed. rity reasons, e.g.
Page 101 Unlocking and locking Security central locking Locking the doors manually if the central locking fails to work The security central locking feature allows you to only unlock the driver's door and the tank flap. All other doors and the Should the central locking system fail to work at any time (for boot lid remain locked.
Page 102 Unlocking and locking Boot lid A manual locking device (only visible when the door is open) is provided on the front passenger's door and the rear doors. – Open the door. Tailgate: opening and closing ⇒ page 99, fig. 71 –...
Page 103: Childproof Locks
Unlocking and locking Childproof locks Opening the tailgate  – Press the centre button on the remote control key or press ⇒ page 100, fig.  the switch* on the driver's door 73. The Childproof locks on rear doors tailgate will spring open. The childproof lock prevents the rear doors from being –...
Page 104: Remote Control Key
Unlocking and locking When the childproof lock is enabled, the inside door handle will not work and the current legal requirements. This certification forms the basis for official the door can only be opened from the outside. approval for use in other countries. Note •...
Page 105  on the remote control. programmed in the key is activated. The driver's seat and exterior mirrors will be automatically adjusted to the positions stored in the memory. – Insert the key into the ignition and switch on the ignition.
Page 106: Anti-Theft Alarm System
Tilt angle (tow-away protection) • Ignition Description • Radio (only with a factory-fitted SEAT radio) • Interior ⇒ page 105 The system triggers an alarm if anyone attempts to break into the vehicle. If any of the named areas are entered, the alarm will be triggered.
Page 107 Unlocking and locking • The alarm is triggered immediately if one of the battery cables is discon- – Then lock the vehicle. nected while the alarm system is enabled. Disabling the tow-away protection  – Open the door and pull out the switch (with the symbol ⇒...
Page 108: Electric Windows
Unlocking and locking Electric windows WARNING (continued) use power-operated equipment (e.g. the electric windows), which could lead to injuries. The window switches are only disabled when the driver's Control switches door or the front passenger's door is opened. • Never close the windows uncarefully or in an uncontrolled manner as this may cause bruising.
Page 109 Unlocking and locking Opening the windows Safety switch ⇒ page 106, fig. 78 The safety switch can deactivate the rear door – Press the switch as far as the first stop and hold it until the switches. The windows can only be operated from the rear when the safety window has moved to the desired position.
Page 110: Sun Roof / Deflector
Unlocking and locking • Opening the windows using the ignition key Release the switch and then lift it again for one second. This will re-enable the automatic function. – unlock the driver's door with the key and hold the key in the unlock position until all the windows are open.
Page 111 Unlocking and locking Sliding/Tilting – With the control in position 0, press the control briefly to make the roof tilt open all the way. The sun roof will create less wind noise if it is opened in the – To open the roof as far as an intermediate setting, press and hold comfort setting.
Page 112 Unlocking and locking Closing the sunroof by overriding the safety cut-out WARNING It is possible to override the safety cut-out to close the Take care when closing the sliding/tilting roof. There is a risk of suffering sunroof. injury. For this reason, always take out the ignition key when leaving the vehicle.
Page 113 Unlocking and locking Closing the sunroof manually – Carefully insert the flat end of a screwdriver (from the car's tool ⇒ fig. kit) at the rear of the glass cover on the interior light The sunroof can be closed by hand if the electrical system –...
Page 114 Lights and visibility Lights and visibility Lights Daytime running lights: In vehicles for countries in which the use of daytime running lights is compulsory, the daytime running light will be enabled or disabled when the engine is started. The headlight flasher is fitted to the ...
Page 115 Lights and visibility Automatic (sensor-controlled) headlights* When you are using the automatic headlights, you can also operate the main beam headlights, however, please note the following: If you enable the main If you set the switch to “AUTO”, the headlights will come on beam headlights while using the automatic headlights function during the day (e.g.
Page 116 Lights and visibility • ⇒ page 112, fig. 83  If you have to attach any type of sticker on the windscreen, do not do so – First turn the light switch to the position   in front of the sensors. Doing so could prevent the automatic headlight or anti-dazzle function from working correctly or even from working at all.
Page 117 Lights and visibility Coming home and leaving home functions* – Press the knob in again to prevent the setting from being changed unintentionally. The coming home and leaving home functions are used to light up the surroundings in the dark. The front fog lights, the The coming home and leaving home functions are controlled by light sensors rear side lights and the number plate light switch on.
Page 118 Lights and visibility – Press the button to increase the brightness. Note • – Press the button to reduce the brightness. If you always wish to use the coming home and leaving home functions, you can leave them permanently switched on. As the system is controlled via a light sensor, it will only work in dark conditions.
Page 119 Lights and visibility ⇒ page 116, fig. 87  Daytime running lights* – Briefly press the knob to release it from its set position. The daytime running lights are enabled automatically when – Turn the knob to the required setting. the ignition is switched on.
Page 120 Lights and visibility – Press the knob in again to prevent the setting from being The cornering light gives better illumination of the side of the road when ⇒ fig. driving around a bend or taking a turn-off 89. The dynamic cornering changed unintentionally.
Page 121 Lights and visibility ⇒ page 118, fig. 90     Indicator and main beam headlight lever – Press the switch to switch the hazard warning lights on or off. The turn signal and main beam headlight lever also operates the parking lights and the headlight flasher.
Page 122: Interior Lights
Lights and visibility  Main beam headlights Caution – Press the lever forward to switch on the main beams. Never use the main beam headlights or the headlight flasher if this would dazzle oncoming traffic. – Pull the lever back towards you to switch the main beam head- lights off again.
Page 123 Lights and visibility Door light position The brightness of the lights is automatically adjusted by a dimmer when they are switched on. – Move switch to the centre position. Interior light switched on Background lighting – Move switch to position I. The background lighting illuminates a number of minor Interior light switched off controls.
Page 124 Lights and visibility Rear reading lights Luggage compartment lighting Fig. 95 Detailed view of the top of the luggage compartment: luggage Fig. 94 Details of head- liner: rear reading lights compartment lighting  The reading lights are switched on and off with the switches The light is in the upper part of the luggage compartment.
Page 125 Lights and visibility Visibility For the sake of the environment Switch of the heated rear window as soon as the rear window has demisted.  Heated rear window By saving electrical power you can also save fuel. The rear window heating clears the rear window of condensa- tion.
Page 126 Lights and visibility Sun blind* Sun blinds (rear side windows) – Pull out the blind and hook it into the hooks at the top of the door Sun blinds are provided for the rear window and the rear side ⇒ fig. frame windows.
Page 127: Windscreen Wipers
Lights and visibility Windscreen wipers – On vehicles equipped with a rain sensor*, you can move the switch up and down to set the sensitivity of the rain sensor.  Windscreen wipers Slow wipe – Move the lever up to position The windscreen wiper lever controls the windscreen wipers and the automatic wash and wipe.
Page 128 Lights and visibility Rain sensor Note The rain sensor* will only function in the intermittent wipe position. The inter- • Check that the washer fluid reservoir is full before starting a long journey. mittent wipe function is enabled automatically when it starts to rain. Fill the reservoir ⇒...
Page 129: Rear-View Mirrors
Lights and visibility Anti-dazzle interior rear-view mirror with automatic Clean off stubborn dirt (insects, etc.) from the lenses at regular intervals, for instance when filling the tank. adjustment* To ensure that the system works properly in winter, keep the nozzle holders The automatic anti-dazzle function can be switched on and off free of snow and remove any ice with a de-icer spray.
Page 130 Lights and visibility • Exterior mirrors the interior lighting is switched on • reverse gear is engaged The exterior mirrors are adjusted electrically. Sensors for automatic headlights* When the light switch is set to the AUTO position, the dipped beam head- lights are switched on and off automatically according to the ambient light level with the aid of the sensors located in the interior rear view mirror ⇒...
Page 131 The mirrors are heated (depending on the outside temperature) when the rear window heater ⇒ page 123 is switched on. Memory for exterior mirrors* On vehicles with memory function for the driver's seat, the setting of the exte- rior mirrors is automatically stored together with the seat position ⇒ page 134.
Page 132: Manual Adjustment Of The Front Seats
WARNING The driver's seat must only be moved forwards and backwards when the vehicle is at a standstill. Failure to do so could result in an accident. Adjusting the seat height* Raising the seat ⇒...
Page 133 Seats and stowage WARNING (continued) • Be careful when adjusting the seat height. Injuries can be caused if the height is adjusted without due care and attention. Adjusting the backrest angle – Lean forwards to take your weight off the backrest.
Page 134: Electric Adjustment Of Front Seats
Fig. 106 Front seat: Seat adjustment switches The adjustment switches for the seat and backrest correspond with the design of the seat. The seats can be adjusted merely by pressing the corresponding switch in the required direction. Moving the seat forwards / backwards Fig.
Page 135: Lumbar Support
To avoid accidental injuries, never leave children unattended in the vehicle. • For safety reasons, the seat must only be adjusted when the vehicle is Lumbar support* at a standstill. Failure to do so could result in an accident.
Page 136: Memory For Driver's Seat
(only STOP visible when the lights are switched on). The stored settings will all remain in the memory. However, the seat and the exterior mirrors can now only be adjusted using the conventional electrical...
Page 137 – Release both buttons. The setting is now stored on the selected The seat adjustment will have to be called up using the memory buttons if the memory button. driver's door is not opened within 10 minutes after unlocking the vehicle with the remote control.
Page 138: Head Restraints
In combination with properly worn seat belts, the head restraints offer effective protection, provided they are prop- Assigning the remote control key to a memory button erly adjusted to suit the height of the occupant.
Page 139 The height of the head restraints is adjustable. They should be set to suit the – Pull up the head restraint as far as it will go. height of the occupant. In combination with the seat belts, the head ⇒ fig. 111 –...
Page 140: Armrests
Seats and stowage Central head restraint of the rear seat When the rear seats are not occupied the head restraints should be moved to the lowest position so that they do not obstruct the driver's field of vision. Armrests The armrest can be adjusted to several positions and incorpo- rates a storage compartment.
Page 141: Luggage Compartment
Seats and stowage Please note that the armrest can restrict the driver's movements when it is – Secure the load with the stretch net* or with non-elastic straps secured to the fastening rings ⇒ page 140. lowered. The armrest should therefore be raised when driving in city traffic. WARNING Luggage compartment •...
Page 142 Seats and stowage Fastening rings Stretch/retaining net* There are four fastening rings in the luggage compartment, The stretch/retaining net can be used to secure and retain which can be used to secure loads. light objects in the luggage compartment. Fig. 115 Location of fastening rings in luggage Fig.
Page 143 Seats and stowage Extending the luggage compartment Stretch net ⇒ page 140, – Secure the stretch net in the four fastening rings The two sections of the backrest can be folded forwards either fig. 116. together or separately to increase the capacity of the luggage compartment.
Page 144 ⇒ page 141, fig. 118 – Press the release lever in the direction When returning the backrest to an upright position, make sure that the seat indicated (arrow). belts for the outer rear seats are in their guides, so that they cannot be caught up and damaged in the catches for the backrest.
Page 145 – Carefully fold away the ski bag. – Close the inside cover of the load-through hatch from the passenger compartment. Fig. 121 Securing the ski bag on the centre seat belt buckle on the rear seat bench Safety First Operating instructions...
Page 146: Roof Carrier
⇒ fig. with arrows on the roof sealing strip 122. The arrows are only visible units from the range of original SEAT accessories. with the doors open. • These carrier units are the basis of a complete roof carrier system. For safety reasons, however, the corresponding additional fastenings must be fitted to carry luggage, bicycles, surfboards, skis and boats.
Page 147: Drink Holders
Seats and stowage Drink holders only be loaded to the maximum weight permitted indicated in the assembly instructions.  Front drink holders WARNING • Loads carried on the roof must be securely attached. Failure to do so could result in an accident. •...
Page 148: Ashtray*, Cigarrette Lighter* And Power Points
Seats and stowage Drink holder in the rear armrest WARNING (continued) • Do not use hard china cups or glasses. These could cause injury in the event of an accident. Ashtray*, cigarrette lighter* and power points Front ashtray* Fig. 124 Drink holder in the rear armrest Opening the drink holder ⇒...
Page 149 Seats and stowage Fitting the ashtray casing Fitting the ashtray casing – Insert the casing and press it into its mountings. – Open the lid on the ashtray and press the casing into the mounting as far as it will go. WARNING WARNING Never put waste paper in the ashtray, as this could cause a fire.
Page 150 Seats and stowage Electrical socket* – Pull out the cigarette lighter immediately. – Use the glowing heater element of the cigarette lighter to light Electrical equipment can be connected to the 12 Volt socket. your cigarette. – Put the cigarette lighter back in its socket. Operating the socket –...
Page 151: Compartments
Seats and stowage Glove compartment Note The glove compartment is equipped with a lock* and a light. The use of electrical appliances with the engine switched off will cause a battery discharge. Compartments Overview There are several storage compartments at various points in the vehicle.
Page 152 Seats and stowage The cool box will only work when the climate control is delivering cooled air. WARNING We recommend you switch off the cool box if the climate control is delivering warm air to heat the interior. For safety reasons, the glove compartment must always be closed when the vehicle is moving.
Page 153 Compartments in the front seats There is a coat hook above each of the rear doors. There is a storage compartment with a lid at the front of each front seat. Opening – Pull the handle to open the compartment.
Page 154: Heating, Ventilation And Air Conditioning
Heating, Ventilation and Air conditioning Heating, Ventilation and Air conditioning 2C-Climatronic If the humidity and temperature outside the vehicle are high, condensation can drip off the evaporator in the air cooling system and form a pool under- neath the vehicle. This is normal and does not indicate a leak. Description If the outside temperature is low, the blower normally only switches to a higher speed once the coolant has warmed up sufficiently (this does not...
Page 155 Heating, Ventilation and Air conditioning Note • Keep the air intake slots in front of the windscreen clear of snow, ice and leaves to ensure unimpaired heating and cooling and to prevent the windows misting over. • The air from the outlets flows through the passenger compartment and out through the slots below the rear window.
Page 156 Heating, Ventilation and Air conditioning Controls This overview will help you become quickly familiar with the controls for the climate control. Fig. 133 Climate control controls The left-hand display shows the temperature selected for the left-hand side Button(s) Meaning and the right-hand display the temperature for the right-hand side. Automatic mode AUTO The functions can be switched on or off by briefly pressing the buttons.
Page 157 Heating, Ventilation and Air conditioning the temperature is not regulated automatically. The temperature is not regu- Button(s) Meaning lated. Adjusts blower speed (centre buttons) Note Air to the windows  By keeping the button on the driver's side pressed for several seconds, AUTO the temperature of the passenger's side can be set to the temperature of the Air from the dashboard outlets...
Page 158 Heating, Ventilation and Air conditioning • Defrosting  When driving through a tunnel or in queues of traffic, to prevent fumes entering the interior of the vehicle. The windscreen and side windows are defrosted or demisted as quickly as possible. WARNING ⇒...
Page 159 Heating, Ventilation and Air conditioning  due to a defect in one of the climate control components. If a malfunction – Press button should occur, please contact a specialist garage. The automatic air recirculation mode should normally be left switched on at all times.
Page 160 Heating, Ventilation and Air conditioning Switching the climate control on/off Blower speed The automatically selected blower speed can be reduced or Switching the climate control off: models with an button increased manually. – Press the button. The climate control is switched off and the supply of air from outside the car is cut off.
Page 161 Heating, Ventilation and Air conditioning Air outlets Fig. 135 Instrument panel: Location of air outlets ⇒ fig. 135 The air outlets can be operated as follows: Note Outlets The cool air provided by the climate control is mainly issued from outlets .
Page 162 Heating, Ventilation and Air conditioning Each of the three buttons has a specific function. The numbers relate to the – If the vehicle has heated up after standing in the sun, open the ⇒ page 159, fig. air outlets 135. windows and doors for a short time to cool the vehicle.
Page 163 1 to 6. Caution To avoid damaging the heating elements of the seat heating, please do not kneel on the seat or apply sharp pressure to a single point. For Nordic countries only.
Page 164: Address
Driving Driving Address WARNING • Never adjust the position of the steering wheel when the vehicle is Adjusting the steering wheel position moving, as this could cause an accident. • For safety reasons, the lever must always be securely engaged when The height and reach of the steering wheel can be adjusted as the vehicle is moving, so that the position of the steering wheel cannot required to suit the driver.
Page 165: Ignition Lock
Driving The Electronic Stabilisation Program (ESP) contains the electronic differential WARNING (continued) lock (EDL) and the traction control system (TCS). The ESP function works • together with the ABS. If a fault in the ABS occurs, both warning lamps light Please refer to the corresponding warning notes on ESP in ⇒...
Page 166: Starting And Stopping The Engine
The engine can only be started with an original SEAT key. Starting the engine The engine is started in this position. Electrical components with a high power consumption are switched off temporarily.
Page 167 Driving • ⇒ page 208, “Refuelling” Vehicles with a diesel engine: – Use the foot brake. WARNING – Manual gearbox: Push the clutch pedal all the way down. Never run the engine in confined spaces, as the exhaust gases are –...
Page 168: Handbrake
Driving Handbrake Caution If the engine has been running hard for a long time, there is a risk of heat Handbrake building up in the engine compartment after the engine has been switched off; this could cause engine damage. Therefore, you should idle the engine The handbrake should be applied firmly to prevent the for approx.
Page 169: Parking Aid
Parking The SEAT parking system gives an acoustic warning if there are any obstacles behind your car ⇒ page 168. The following points will ensure there is no risk of the car rolling away accidentally after it is parked.
Page 170 SEAT parking system plus* The volume of the warning beeps will be gradually reduced after about 4 The SEAT parking system plus is an acoustic parking aid. seconds if the vehicle remains at a constant distance from a detected obstacle (it will not be reduced if the obstacle is closer than 0.30 m).
Page 171 Driving Enabling/Disabling WARNING • The parking aid is not a replacement for driver awareness. The driver is personally responsible for safe parking and other manoeuvres. • The sensors have blind spots in which obstacles are not registered. Always look out for small children and animals because the system will not always detect them.
Page 172: Cruise Control System (Ccs)
There is no distance warning. SEAT parking system plus* WARNING There is no rear distance warning. The system will still give a warning when obstacles are detected while driving forwards.
Page 173 Driving Setting speed Adjusting stored speed The desired cruising speed needs to be stored in the memory. The desired cruising speed can be adjusted up or down as required. Acceleration ⇒ fig. 143 – Move the lever up towards – Release the lever to store the current cruising speed. Decelerating ⇒...
Page 174 Driving Disabling cruise control temporarily WARNING Retrieve the programmed speed only if this is not excessive for the current traffic conditions. Failure to do so could result in an accident. Disabling the cruise control While driving ⇒ page 171, fig. 143 –...
Page 175: Manual Gearbox
Driving Manual gearbox WARNING • When the engine is running, the vehicle will start to move as soon as a Driving a car with a manual gearbox gear is engaged and the clutch released. • Never select the reverse gear when the vehicle is in motion. Risk of acci- dent.
Page 177: Practical Tips
Intelligent technology Practical tips Intelligent technology Electronic stabilisation programme (ESP) The anti-lock brake system (ABS), the electronic differential lock (EDL) and the traction control system (TCS) are all integrated into the electronic stabili- sation programme. General notes How it works The electronic stabilisation programme increases the The ESP control unit processes data from the three integrated systems.
Page 178 Intelligent technology If required, the ESP can also be enabled and disabled manually by briefly How the ABS works ⇒ page 175, fig. pressing the switch 146. The ESP warning lamp lights The system runs an automatic self-check when the car reaches a road speed up when the system is switched off, see ⇒...
Page 179 Intelligent technology the brake assist system automatically boosts the braking force to the other wheels. The systems works up to a speed of approx. 80 km/h. The maximum level, up to the point where the anti-lock brake function (ABS) inter- system will make noises while it is working.
Page 180: Brakes
Intelligent technology (TCS)Traction control system Brakes The traction control system prevents the drive wheels from General notes spinning when the car is accelerating. General notes New brake pads The traction control system (TCS) is one of the functions incorporated in the New brake pads do not provide optimal performance during the first 400 km electronic stabilisation programme (ESP).
Page 181: Power Steering
Intelligent technology Corrosion Note There may be a tendency for dirt to build up on the brake pads and corrosion If you wish to equip the car with accessories such as a front spoiler or wheel to form on the discs if the car is used infrequently, or if you only drive low covers, it is important that the flow of air to the front wheels is not obstructed, mileages without using the brakes very much.
Page 182: Servotronic
Intelligent technology The power steering does not work if the engine is off. In this case the steering If a fault should occur in the servotronic system, the power steering will still wheel is very hard to turn. operate. The degree of power assistance will, however, no longer adapt to different speeds.
Page 183: Driving And The Environment
Driving and the environment Driving and the environment Running-in Braking effect and braking distance The braking effect and braking distance are influenced by Running in a new engine driving situations and road conditions. The engine needs to be run-in over the first 1,500 km. The efficiency of the brakes depends directly on the brake pad wear.
Page 184: Exhaust Gas Purification System
Driving and the environment – Never tow the vehicle to start it, use jump leads if necessary WARNING (continued) ⇒ page 271. your vehicle has automatic transmission). This makes use of engine braking and relieves the brakes. If you notice misfiring, uneven running or loss of power when the vehicle is •...
Page 185: Economical And Environmentally Friendly Driving
Driving and the environment Diesel engine particulate filter* ical driving style and anticipating the traffic situation ahead, you can easily reduce fuel consumption by 10-15%. Some tips on how to help you reduce The diesel engine particulate filter eliminates soot produced pollution while saving money are listed below.
Page 186 Environmental protection is a top priority in the design, choice of materials With the engine cold, fuel consumption is proportionally higher. The engine and production of your new Seat. does not warm up and fuel consumption does not regularise until having Design measures for economical recycling driven some four kilometres.
Page 187: Driving Abroad
Authorised Service Centre may only carry out limited repairs. SEAT importers and distributors will gladly provide information about the technical preparation of your vehicle and also about necessary maintenance and repair possibilities.
Page 188: Trailer Towing
If the trailer has a 7-pole connector you therefore the vehicle's climbing ability are impaired because of the reduced can use an adapter cable. This can be purchased from any SEAT Dealer. air density. The maximum trailer weight has to be reduced accordingly. The...
Page 189 Trailer towing Notes on towing Where possible, operate the trailer with the maximum permitted draw bar weight on the ball joint of the towing bracket, but do not exceed the specified Towing a trailer involves additional attention by the driver. limit.
Page 190 ⇒ WARNING • If you wish to mount equipment which has not been approved by SEAT, please ensure that it is suitable for use on SEAT vehicles. • The use of unsuitable accessory equipment can result in severe damage to the towing bracket, and it could then break while pulling a trailer - Risk Fig.
Page 191: Removable Towing Bracket
To prevent damage to the ball joint from unsuitable equipment, we Introduction recommend that equipment for the towing bracket be purchased through your SEAT Dealer. Also refer to ⇒ page 206. Special care is required when fitting and removing the towing bracket.
Page 192 Trailer towing Fitting the ball joint (step 1) Fitting the ball joint (step 2) Fig. 149 Rear bumper: Fig. 150 Removable Open the cover piece towing bracket: Ball joint ⇒ fig. 149 – Remove the cover piece on the mounting fixture below the bumper as far as it will go.
Page 193 Trailer towing Fitting the ball joint (step 3) Make sure the ball joint is clean and undamaged – Check the locking pin , release pin , shaft section ⇒ page 190, fig. 150 knob on the ball joint to make sure they are clean and undamaged.
Page 194 Trailer towing Fitting the ball joint (step 4) Setting the spring mechanism to the ready position (if required) ⇒ page 191, fig. 152 – Insert the key in the lock on the knob and turn it towards the red marking. –...
Page 195 Trailer towing Removing the ball joint Safety check ⇒ page 192, fig. 154 – Check that the green marking on the knob is inside the black zone marked on the ball joint. – Check that the knob is directly against the ball joint, so that there is no gap between the knob and the ball joint -arrow-.
Page 196 Trailer towing – Take hold of the ball joint and pull out the knob in direction – Keep hold of the knob and turn it as far as it will go in direction – Release the knob. The spring mechanism will remain in the ready position ⇒...
Page 197 Trailer towing Fitting a towing bracket* It is possible to fit a towing bracket to the rear of the vehicle. Fig. 158 Attachment points for towing bracket Safety First Operating instructions Practical tips Technical Data...
Page 198 Trailer towing If a towing bracket is to be fitted after the vehicle is purchased, this must be WARNING (continued) completed according to the instructions of the towing bracket manufacturer. • If the towing bracket is incorrectly installed, there is serious danger of The attachment points for the towing bracket are on the lower part of the accident.
Page 199: Your Vehicle Maintenance And Cleaning
Your vehicle maintenance and cleaning Your vehicle maintenance and cleaning General notes WARNING (continued) your vehicle. The use of certain products may produce noxious vapours; Regular washing and care help maintain the value of your they should be used in well ventilated areas. vehicle.
Page 200: Vehicle Exterior Maintenance
Your vehicle maintenance and cleaning Vehicle exterior maintenance – Clean your vehicle from top to bottom with a soft sponge, a glove or a brush. Use very light pressure. – Rinse the sponge or glove often with clean water. Automatic car wash tunnel –...
Page 201 Your vehicle maintenance and cleaning – Never use concentrated jet nozzles (“rotating jets”) ⇒ Caution • – Directly after washing, avoid sudden and sharp braking. “Dry” Never remove dirt, mud or dust if the vehicle surface is dry. Never use a ⇒...
Page 202 Your vehicle maintenance and cleaning Regular wax applications help to protect the paintwork from environmental contaminants to a great extent ⇒ page 197. It is also effective in protecting Caution • against minor scratches. The use of liquid air freshener directly over the air vents of the vehicle may damage the plastic parts if the liquid is accidentally spilled.
Page 203 Your vehicle maintenance and cleaning to the windscreen washer fluid prevents wiper blades from juddering. Wax The strips on the doors, windows, bonnet and rear lid will remain pliable and deposits are not removed. last longer if they are treated with a suitable care product (for example sili- cone spray).
Page 204 Your vehicle maintenance and cleaning Steel wheel rims Car polish or other abrasive agents should not be used. If the protective coating is damaged, e.g. by stone impact, the damaged area should be repaired immediately. – Clean steel wheel rims regularly using a separate sponge. WARNING Use an industrial cleanser to remove brake dust.
Page 205: Vehicle Interior Maintenance
Your vehicle maintenance and cleaning Cleaning the engine compartment WARNING (continued) • Take special care when cleaning the engine compartment. Never touch the radiator fan. It is temperature-controlled and could start automatically, even when the key is removed from the ignition! Anti-corrosion treatment The engine compartment and the surface of the power unit are given anti- For the sake of the environment...
Page 206 Cloth seat covers and fabric trim on the doors, headlining etc. can be cleaned so a degree of care is required in everyday use and when looking after the with a special interior cleanser or with dry foam and a soft brush.
Page 207 If large stains form on the belts, it will not retract correctly into the automatic belt retractor. WARNING • Do not use chemical cleaning agents on the seat belts, as this can impair the strength of the webbing. Ensure that belts do not come into contact with corrosive fluids. •...
Page 208: Accessories, Parts Replacement And Modifications
Despite a continuous observation of the market, SEAT is not able to assess faults. This can seriously impair safety, lead to excessive wear of compo- the reliability, safety and suitability of those parts SEAT has not approved.
Page 209: Mobile Telephones And Radiotelephones
Accessories, parts replacement and modifications Athermic windscreen* WARNING Incorrectly performed modifications or other kind of work on your vehicle can lead to malfunctions and cause accidents. Mobile telephones and radiotelephones First consult your Authorised Service Centre if you wish to use a mobile tele- phone or a two-way radio with a transmitting power output in excess of 10 watts.
Page 210: Checking And Refilling Levels
Checking and refilling levels Checking and refilling levels Refuelling Closing the tank cap – Screw the tank cap clockwise into the filler opening until it you The tank flap is released manually. The tank holds approxi- hear it click into position. mately 70 litres.
Page 211: Releasing The Tank Flap Manually
Checking and refilling levels Releasing the tank flap manually WARNING (continued) − Insert the fuel nozzle into the mouth of the canister as far as The tank flap can be released manually if the central locking possible. system should fail to operate. −...
Page 212: Petrol
Checking and refilling levels Petrol Petrol additives Petrol additives improve the quality of the petrol. Petrol types The quality of the petrol influences running behaviour, performance and The recommended fuel types are listed on a sticker inside the service life of the engine. For this reason, you should use good quality petrol containing additives.
Page 213 Checking and refilling levels Winter driving Your Authorised Service Centre can also be consulted to know if the vehicle has been prepared for biodiesel use. Diesel can thicken in winter. Things to note about RME fuel (biodiesel) • The performance of a vehicle using biodiesel maybe somewhat reduced. Winter-grade diesel •...
Page 214: The Bonnet
Checking and refilling levels The bonnet Opening the bonnet Releasing the bonnet The bonnet is released from inside the vehicle. Fig. 163 Release catch under the bonnet Fig. 162 Detail of foot- Before opening the bonnet make sure that the windscreen wiper well area on driver's side: arms are not lifted away from the glass.
Page 215 Checking and refilling levels WARNING (continued) WARNING • Never touch the radiator fan while the engine is hot, as the fan could Never open the bonnet if you see steam or drips of coolant being released start up suddenly. from the engine compartment. Failure to comply could result in burns. Wait •...
Page 216: Engine Oil
Checking and refilling levels The correct oil specifications for your engine are listed in the Technical data section ⇒ page 282. Note On right-hand drive vehicles some of the containers/ reservoirs mentioned Check that the specifications quoted (VW standards) appear on the container below are located on the other side of the engine compartment.
Page 217 Checking and refilling levels Oil properties These oils are only useful in a climate that is constantly very cold or very warm. Engine oil additives No type of additive should be mixed with the engine oil. The deterioration caused by these additives is not covered by the warranty. Note Before a long trip, we recommend finding an engine oil that conforms to the corresponding VW specifications and keeping it in the vehicle.
Page 218 Checking and refilling levels  Topping up the engine oil Checking oil level – Park the vehicle in a horizontal position. – Briefly run the engine at idle speed until the service temperature is reached then stop. – Wait two minutes. –...
Page 219: Cooling System
Checking and refilling levels The cooling system is filled at the factory with the correct amount of anti- Caution freeze for the country concerned. • The oil level must never be above area . This could damage the cata- In most cases, the mixture consists of 60% water and 40% anti-freeze. This lytic converter or the engine.
Page 220 Checking and refilling levels tion. The damage caused by the use of these anti-freezes may lead to a loss The liquid coolant level should be checked with the engine switched off. of liquid coolant, causing serious damage to the engine. The liquid coolant level is monitored by a warning lamp in the instrument •...
Page 221 Checking and refilling levels Radiator fan Make sure that the liquid coolant meets the required specifications ⇒ page 217, “Liquid coolant”. Do not use a different type of anti-freeze if The radiator fan can start running spontaneously. anti-freeze G12++ is not available. In this case, use only water and bring the anti-freeze concentration back up to the correct level as soon as possible.
Page 222: Washer Fluid And Windscreen Wiper Blades
Checking and refilling levels Washer fluid and windscreen wiper blades Caution • Never put radiator anti-freeze or other additives into the windscreen Windscreen washer system washer fluid. • Never use washer fluid which contains paint thinners or solvents as it can Plain water on its own is not sufficient for the windscreen damage the paintwork.
Page 223 Checking and refilling levels Changing windscreen wiper blades Removing the wiper blade – Lift the wiper arm away from the windscreen. If the windscreen wiper blades are in perfect condition, you will benefit from an improved visibility. Damaged wiper – Slide the retainer catch on the wiper blade in the direction indi- ⇒...
Page 224: Brake Fluid
Checking and refilling levels Brake fluid WARNING (continued) • To prevent smearing on the windscreen, the wiper blades should be Checking the brake fluid level cleaned regularly using a window cleaner solution. If the wiper blades are very dirty (e.g. insects etc.), they should be cleaned using a sponge or The brake fluid level can be checked at a glance.
Page 225: Battery
Checking and refilling levels Topping up and changing the brake fluid For the sake of the environment It is best to have the brake fluid changed by a professional. If the fluid has to be drained out of the brake system, use an appropriate container to catch the used brake fluid and dispose of it in the proper Brake fluid absorbs damp.
Page 226 Battery acid is very corrosive and caustic. Wear protec- rating. It must also have the same dimensions as the original, factory-fitted tive gloves and eye protection! battery and have sealed caps. The SEAT batteries which have been specially  developed fulfil the maintenance, performance and safety specifications for Fires, sparks, naked lights and smoking are prohibited! your vehicle.
Page 227 Checking and refilling levels Charging the battery WARNING (continued) • A fully-charged battery is important for reliable starting. A highly explosive mixture of gases is released when the battery is under charge. The batteries should be charged in a well-ventilated room –...
Page 228 Checking and refilling levels the appropiate knowledge level. We therefore recommend that this work should only be performed by a specialist garage. A flat battery can freeze at temperatures of around 0°C. The battery must be defrosted before charging ⇒ .
Page 229: Wheels And Tyres
Wheels and tyres Wheels and tyres Wheels Concealed damage Damage to tyres and rims is often not readily visible. If you notice unusual vibrations or the car pulling to one side, this may indicate that one of the tyres General notes is damaged.
Page 230 Wheels and tyres Tyre pressure monitoring 2. The tyre pressures should only be checked when the tyres are cold. The slightly raised pressures of warm tyres must not be The tyre pressure monitoring system constantly checks the reduced. pressure of the tyres. 3.
Page 231 Wheels and tyres Significant tyre pressure loss wheels. If the rolling circumference or frequency characteristic changes on  one or more wheels, the tyre pressure warning lamp will light up. The fault will also be indicated by a warning buzzer. The position of the affected tyre ...
Page 232 Wheels and tyres Tyre service life TMPS (Tyre Pressure Monitoring System). Please contact the nearest specialist garage as soon as possible. The service life of tyres is dependent on tyre pressure, driving  The tyre pressure warning lamp lights up if the tyre pressure on one or style and fitting.
Page 233 Wheels and tyres Wear indicators Wheel balance The original tyres on your vehicle have 1.6 mm high “tread wear indicators” The wheels on new vehicles are balanced. However, various factors encoun- ⇒ page 230, fig. 173, running across the tread. Depending on the make, tered in normal driving can cause them to become unbalanced, which results there will be six to eight of them evenly spaced around the tyre.
Page 234 Wheels and tyres Anti-puncture tyres* necessary. We recommend you contact Technical Service. If more than one tyre is being used under emergency conditions, this reduces the distance Anti-puncture tyres allow you to continue driving even with a which can be travelled. punctured tyre, in the majority of cases.
Page 235 We recommend that you use only wheels and tyres which have been handling ⇒ approved by SEAT for your model. Failure to do so could impair vehicle Tyres should be replaced at least in pairs and not individually (i.e. both front handling.
Page 236 This can also apply to wheels of the same model. The use of • wheels or tyres which have not been approved by SEAT for use with your If the torque of the wheel bolts is too low, they could loosen whilst the model may invalidate the vehicle's type approval for use on public roads.
Page 237 Wheels and tyres Snow chains Winter tyres lose their effectiveness when the tread is worn down to a depth of 4 mm. The speed rating code ⇒ page 233, “New tyres and wheels” determines the Snow chains may be fitted only to the front wheels, and only to certain tyre sizes ⇒...
Page 238: If And When
If and when If and when Tools, tyre repair kit and spare wheel – Take out the tools or jack. – Replace the floor panel before closing the tailgate. Tools The tool kit includes: The tools and jack are stored under the floor panel in the •...
Page 239 If and when Tyre mobility system Spare steel rim wheel The tyre mobility system is stored under the floor panel in the The spare steel rim wheel is carried in the wheel well under luggage compartment. the floor panel in the luggage compartment. It is only intended for temporary use over short distances.
Page 240: Changing A Wheel
If and when Changing a wheel Your vehicle can be equipped with a steel spare wheel at the factory. The spare wheel does not usually meet the same performance standards as the wheels fitted on the vehicle because of the wheel/tyre dimensions, rubber composition, tread pattern, etc.
Page 241 If and when – The inflation pressure of the newly fitted spare tyre must be Note checked as soon as possible. Please observe legal requirements when doing so. – Have the tightening torque of the wheel bolts checked as soon as possible with a torque wrench.
Page 242 If and when Loosening and tightening the wheel bolts WARNING The wheel bolts must be loosened before raising the vehicle. Loosen the wheel bolts only about one turn before raising the vehicle with the jack. Failure to do so could result in an accident. Note •...
Page 243 If and when Raising the vehicle – Position the vehicle jack under the door sill at the jacking point ⇒ fig. 179 closest to the wheel being changed -arrows-. In order to remove the wheel, the vehicle must be raised with –...
Page 244 If and when Removing and fitting the wheel The wheel bolts should be clean and easily screwed. Before fitting the spare wheel, inspect the wheel condition and hub mounting surfaces. These For removal and fitting the wheel, the following tasks must be surfaces must be clean before fitting the wheel.
Page 245: Tyre Repair* (Tyre-Mobility-System)
If and when Tyre repair* (Tyre-Mobility-System) – Insert the adapter onto the wheel bolt and push it on as far as it ⇒ page 242, fig. will go 182. – Fit the box spanner as far as it will go over the adapter. General information and safety notes –...
Page 246 If and when The sealing compound must not be used in the following cases: WARNING (continued) • ⇒ page 243, fig. 183 On cuts and punctures larger than 4 mm • • If you do come into contact with the sealant immediately rinse the eyes if the wheel rim has been damaged or skin affected with clean water.
Page 247 If and when Repairing a tyre – Stick the “max. 80 km/h” adhesive, which is included with the tyre sealant can, onto the instrument panel where the driver will see it. Filling the tyre – Shake the tyre sealant can well. –...
Page 248 If and when – If the tyre pressure remains lower than the value specified above Note drive the vehicle approx. 10 metres forwards or backwards, so • Do not use the compressor for longer than 6 minutes. Otherwise, it might that the sealant can spread evenly in the tyre.
Page 249: Fuses
If and when Fuses – Switch off the ignition and its failed electrical component. ⇒ fig. – Remove the fuse cover using a screwdriver 185. Changing fuses – Identify the fuse for the failed component ⇒ page 248, “Fuse assignment”. If a fuse has blown, it must be replaced.
Page 250 If and when Fuse assignment No. Consumer Amps This list shows the fuses which can be replaced relatively Fog lights easily by the owner. Vacant Vacant No. Consumer Amps Driver's door / front passenger's door Climate control Rear doors Footwell lamps Central electrics unit for convenience equipment Heated washer jets Heater blower...
Page 251: Bulbs
⇒ page 213 ⇒ in “Types of bulbs”. The electric windows and electric seat adjusters are protected by circuit breakers. These reset automatically after a few seconds when the overload (caused for example by frozen windows) has been corrected.
Page 252 If and when vaporise as a result of the heat generated by the bulb, be deposited on the WARNING (continued) reflector and impair its surface. • Bulbs are highly sensitive to pressure. The glass can break when you touch the bulb, causing injury. •...
Page 253 If and when Fitting the air duct Halogen headlight bulbs Once the bulb(s) for the right-side headlight have been changed, the air duct must be re-installed. Fig. 189 Halogen bulbs Fig. 188 Air duct on right Main beam headlights side of vehicle Side lights Dipped headlights –...
Page 254 If and when Changing the turn signal bulb Note ⇒ page 254, The procedure for changing the bulbs on the front Although it is not necessary, previously remove the rigid cover fig. 193 for easier turn signal bulb changes. passenger's side is the same as on the driver's side. Fig.
Page 255 If and when Changing the main headlight bulb – Switch off the ignition and the lights. The procedure for changing the bulbs on the front – Raise the bonnet. passenger's side is the same as on the driver's side. ⇒ fig. 191 –...
Page 256 If and when Changing the dipped beam headlight bulb – Switch off the ignition and the lights. The procedure for changing the bulbs on the front – Raise the bonnet. passenger's side is the same as on the driver's side. ⇒...
Page 257 If and when Changing side light bulb (outside of vehicle) – Switch off the ignition and the lights. The procedure for changing the bulbs on the front – Raise the bonnet. passenger's side is the same as on the driver's side. ⇒...
Page 258: Changing Bulbs. Bi-Xenon Afs Headlights
If and when Changing the side light bulb (inside of vehicle) – Switch off the ignition and the lights. The procedure for changing the bulbs on the front – Raise the bonnet. passenger's side is the same as on the driver's side. ⇒...
Page 259 If and when phenomenon has no influence on the life expectancy of the vehicle lights. If Bulb Type headlamps are switched on, the area where the light shaft is projected, is demisted in little time. However, the edges may be steamed up on the inte- Xenon bulbs 12 V/35 W (D1S) rior.
Page 260 If and when ⇒ page 257, fig. Bi-Xenon AFS headlight bulbs – Unscrew bolts 199. – Detach air duct from guide and take it out. Fitting the air duct Once the bulb(s) for the right-side headlight have been changed, the air duct must be re-installed. Fig.
Page 261 If and when Changing the DRL light bulb (day light) Note ⇒ page 261, The procedure for changing the bulbs on the front Although it is not necessary, previously remove the rigid cover fig. 205 for easier day light bulb changes. passenger's side is the same as on the driver's side.
Page 262 If and when Changing the turn signal bulb – Switch off the ignition and the lights. The procedure for changing the bulbs on the front – Raise the bonnet. passenger's side is the same as on the driver's side. ⇒ fig. 203 –...
Page 263 If and when Changing the side light bulb – Switch off the ignition and the lights. The procedure for changing the bulbs on the front – Raise the bonnet. passenger's side is the same as on the driver's side. ⇒ fig. 205 –...
Page 264: Changing Rear Bulbs (In Side Panel)
If and when Changing rear bulbs (in side panel) Removing rear light To change the bulbs, you must remove the rear light. Overview of rear lights Removing the light requires a certain degree of practical skill. Fig. 208 Luggage compartment: Location of the bolt securing the rear Fig.
Page 265 If and when Removing the bulb holder A special retaining screw is used to secure and guide the rear light. – Check which of the bulbs is defective. When changing a bulb, you must first remove the bulb holder. – Open the tailgate. –...
Page 266 If and when Changing bulbs Position of the bulbs ⇒ fig. 211 Pos. Bulb function All bulbs can be changed easily in the bulb holder. Brake lights and rear lights Rear light Indicator light Fitting the bulb holder The bulb holder is easy to fit. –...
Page 267 If and when ⇒ fig. 212 Fitting the rear light unit – First place the rear light unit in arrow in the housing. The rear light unit is easy to fit. – Gently press the rear light unit against the housing, first in posi- tion and then in position , until that the clips engage firmly...
Page 268: Changing Rear Light Bulbs (In Boot Lid)
If and when Changing rear light bulbs (in boot lid) Removing the bulb holder The tailgate must be open to change the bulbs. Overview of rear lights Fig. 215 Remove the cover in the tailgate Fig. 214 Overview of rear lights Rear lights in the boot lid •...
Page 269 If and when You can access the bulb holder for the inner rear lights via the inside The bulbs are secured with a bayonet fastener. The table below of the tailgate. gives an overview of the bulb positions. – Check which of the bulbs is defective. –...
Page 270: Side Indicators
If and when – Fit the cover back in the interior trim so that it engages. – First place the indicator in the opening in the bodywork, fixing ⇒ fig. the tabs 218, arrow – Put the screwdriver back into the tool kit. ⇒...
Page 271: Luggage Compartment Lights
If and when Luggage compartment lights – Remove the tulip-shaped fitting by pressing on its inside edge using the flat side of a screwdriver. – Remove the protective cover and remove the bulb from the ⇒ fig. housing 220. Fig. 219 Luggage compartment light Fig.
Page 272: Registration Light
If and when ⇒ fig. Registration light – To remove the tulip-shaped fitting, unscrew the bolts 221. – Remove the bulb, moving it in the direction of the arrow and ⇒ fig. outwards 222. – Installation is in the reverse order. Fig.
Page 273: Sunroof Light
If and when Sunroof light – Use a screwdriver to remove the protective cover. – Remove the bulb, moving it in the direction of the arrow and ⇒ fig. outwards 224. Jump-starting Jump leads The jump lead must have a sufficient wire cross section. If the engine fails to start because of a discharged battery, the battery can be Fig.
Page 274 If and when How to jump start: description 4. Connect the other end of the black jump lead to a solid metal component which is bolted on to the engine block, or onto the engine block itself of the vehicle with the flat battery. Do not connect it to a point near the battery ⇒...
Page 275 If and when WARNING • Please note the safety warnings referring to working in the engine compartment ⇒ page 213. • The battery providing assistance must have the same voltage as the flat battery (12V) and approximately the same capacity (see imprint on battery).
Page 276: Towing And Tow-Starting
If and when Towing and tow-starting Comments Please observe the following points if you use a tow-rope: Tow-starting Notes for the driver of the towing vehicle The use of jump leads is preferable to tow-starting. – Drive slowly at first until the tow-rope is taut. Then accelerate We recommend that you do not tow-start your vehicle.
Page 277 If and when Front towing eye Do not pull too hard with the towing vehicle and take care to avoid jerking the tow-rope. When towing on an unpaved road, there is always a risk of over- loading and damaging the anchorage points. The ignition of the vehicle being towed must be switched on to prevent the steering wheel from locking and also to allow the use of the indicators, horn, windscreen wipers and washers.
Page 279: Technical Data
General notes on the technical data Technical Data General notes on the technical data Outstanding information Important considerations All data in the official vehicle documents take precedence over this data. All data provided in this manual are valid for the standard model in Spain. The The figures may be different depending on if additional equipment is fitted, vehicle data card included in the Maintenance Programme or the vehicle for different models, for special vehicles and for other countries.
Page 280 General notes on the technical data Vehicle identification data Vehicle data The data sticker is placed on the inside of the spare wheel recess in the The most important data are given on the type plate and the luggage compartment. vehicle data sticker.
Page 281: Data On Fuel Consumption
General notes on the technical data Data on fuel consumption Fuel consumption The consumption and emission details shown on the vehicle data sticker differ from one vehicle to another. The fuel consumption and CO emissions of the vehicle can be found on the The consumption and emission figures are calculated in accordance with the vehicle data sticker.
Page 282: Towing A Trailer
General notes on the technical data Weights Drawbar load The maximum permitted weight exerted by the trailer drawbar on the ball joint of the towing bracket must not exceed 75 kg. Kerb weight refers to the basic model with a fuel tank filled to 90% capacity and without optional extras.
Page 283 General notes on the technical data Snow chains Snow chains may be fitted only to the front wheels. Consult the chapter “wheels” of this manual. Wheel bolts After the wheels have been changed, the tightening torque of the wheel bolts should be checked as soon as possible with a torque wrench ⇒...
Page 284: Technical Data
Technical Data Technical Data Checking fluid levels Vehicle battery Engine oil filler cap From time to time, the levels of the different fluids in the Brake fluid reservoir vehicle must be checked. Never fill with incorrect fluids, Engine oil dipstick. Coolant expansion tank otherwise serious damage to the engine may be caused.
Page 285: Petrol Engine 1.6L 75 Kw (102 Hp)
Technical Data Petrol engine 1.6l 75 kW (102 HP) General engine data Power output in kW (bhp) 75 (102) / 5600 Maximum torque in Nm at 1/min 148 / 3800 No. of cylinders/ cubic capacity 4 / 1595 in cm Compression 10,3 +/- 0,3 Fuel...
Page 286: Petrol Engine 1.8L 110 Kw (150 Hp)
Technical Data Trailer weights Trailer without brakes Trailer with brakes, gradients up to 8% 1400 Trailer with brakes, gradients up to 12% 1200 Engine oil capacity Approximate engine oil capacity with oil filter change 3.6 litres Petrol engine 1.8l 110 kW (150 HP) General engine data Power output in kW (HP) 110 (150) / 5700...
Page 287: Petrol Engine 2.0L 147 Kw (200 Hp)
Technical Data Weights Gross vehicle weight in kg 1960 Weight in working order (with driver) in kg 1475 Front gross axle weight in kg 1065 Rear gross axle weight in kg 1025 Permitted roof load in kg Trailer weights Trailer without brakes Trailer with brakes, gradients up to 8% 1600 Trailer with brakes, gradients up to 12%...
Page 288 Technical Data Performance figures Maximum speed in km/h Acceleration from 0-80 km/h in sec. Acceleration from 0-100 km/h in sec. Weights Gross vehicle weight in kg 1990 Weight in working order (with driver) in kg 1505 Front gross axle weight in kg 1090 Rear gross axle weight...
Page 289: Diesel Engine 2.0L 105 Kw (143 Hp)
Technical Data Diesel engine 2.0l 105 kW (143 hp) Engine specifications Power output in kW (bhp) 105 (143) / 4200 Maximum torque in Nm at rpm 320 / 1750-2500 No. of cylinders/ cubic capacity 4 / 1968 in cm Compression 16,5 +/- 0,3 Fuel Min.
Page 290: Diesel Engine 2.0L 125 Kw (170 Hp)
Technical Data Trailer weights Trailer without brakes Trailer with brakes, gradients up to 8% 1800 Trailer with brakes, gradients up to 12% 1600 Engine oil capacity Approximate engine oil capacity with oil filter change 4.6 litres Diesel engine 2.0l 125 kW (170 hp) Engine specifications Power output in kW (bhp) 125 (170) / 4200...
Page 291 Technical Data Weights Vehicle maximum gross weight in kg 2015 Weight in working order (with driver) in kg 1530 Front gross axle weight in kg 1115 Rear gross axle weight in kg 1030 Permitted roof load in kg Trailer weights Trailer without brakes Trailer with brakes, gradients up to 8% 1800...
Page 292: Dimensions And Capacities
Technical Data Dimensions and capacities Dimensions Length, width 4,661 mm/ 1,772 mm Height at kerb weight 1,430 mm Front and rear projection 976 mm/ 1,043 mm Wheelbase 2,642 mm Turning circle 11.2 m Front Rear Track width 1,522 mm 1,523 mm Capacities Fuel tank 70 l.
Page 293: Index
Index Index Anti-theft alarm system ....104 Belt tension device Interior monitoring ....105 Disposal .
Page 294 Diesel engine Child seat ....... 48 Clock, setting ......61 Winter driving .
Page 295 Driving time ......84 Assigning the key to the seat ... 136 Disconnecting the battery .
Page 296 Floor mats ......16 Heated seat ......161 Fog lights .
Page 297 Mobile telephones and radiotelephones ..207 Settings for the driver's seat ... . 136 Battery ......223 Luggage compartment .
Page 298 Running in SEAT parking system ....168 Engine ......181 Rear view mirror SEAT parking system plus .
Page 299 Electric windows ..... 106 Seat belts ....... 18 Sitting position, occupants .
Page 300 Products for vehicle maintenance ..197 Why wear seat belts? ....19, 28 Trip recorder ......63 Waxing .
Page 301 Index Winter driving Diesel engine ......211 Winter operations Battery ......224 Winter tyres .
Page 302 SEAT S.A. is permanently concerned about continuous development of its types and models. For this reason we ask you to understand, that at any given time, changes regarding shape, equipment and technique may take place on the car delivered. For this reason no right at all may derive based on the data, drawings and descriptions in this current handbook.

Seat EXEO 2009 Owner's Manual

Quick Links

Related Manuals for Seat EXEO 2009

Summary of Contents for Seat EXEO 2009

Table of Contents