Seat IBIZA Owner's Manual
  1. Manuals
  2. Brands
  3. Seat Manuals
  4. Automobile
  5. ibiza
  6. Owner's manual

Seat IBIZA Owner's Manual

Hide thumbs Also See for IBIZA:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
auto emoción

Advertisement

Table of Contents
loading

Related Manuals for Seat IBIZA

Summary of Contents for Seat IBIZA

  • Page 1 auto emoción...
  • Page 3 Foreword This owner's manual and the corresponding supplements should be read carefully to familiarise yourself quickly with your vehicle. Also, the regular care and maintenance and correct handling of the vehicle will contribute to the conservation of its value. For safety reasons, note the information concerning accessories, modifications and parts exchange. If selling the vehicle, give all of the onboard documentation to the new owner because as this belongs with the vehicle.

  • Page 5: Table Of Contents

    Tips and Maintenance Seat belts ..........
  • Page 6 Contents Accessories, parts replacement and Petrol engine 1.4 16 V 55 kW (75 CV) ..modifications Petrol engine 1.4 16 V 55 kW (75 CV) Automatic ......Petrol engine 1.4 16 V 74 kW (101 CV) .

  • Page 7: The Structure Of This Manual

    Because this is a general manual for the IBIZA, some of the equipment and functions that are described in this manual are not included in all types or For the sake of the environment variants of the model;...

  • Page 8: Content

    (e.g.“Air conditioning”). The entire manual is divided into five large parts which are: 1. Safety First Information on the vehicle equipment relating to passive safety such as seat belts, airbags, seats, etc. 2. Controls and equipment...

  • Page 9: Safety First

    The This chapter contains important information, advice, suggestions following list includes most of the safety equipment in your SEAT: and warnings that should be read and followed in the interest of •...
  • Page 10 – Adjust front seat, head restraint and mirrors properly for your size. – Observe traffic laws and speed limits. – Ensure that the passenger in the central rear seat always has the – Always reduce your speed as appropriate for road, traffic and head restraint in position.

  • Page 11: Proper Sitting Position For Occupants

    25 cm between the steering wheel and the centre of your chest and relaxed driving. ⇒ fig. – Move the driver's seat forwards or backwards so that you are able to press the accelerator, brake and clutch pedals to the floor with your knees still slightly angled ⇒...
  • Page 12 For detailed information on how to adjust the front passenger's seat, see rest is in an upright position and the driver is wearing his or her seat belt ⇒ page 103.
  • Page 13 • Always keep your feet in the foot well when the vehicle is moving; never rest them on the instrument panel, out the window or on the seat. An WARNING incorrect sitting position exposes you to an increased risk of injury in the •...
  • Page 14 Safe driving Correct adjustment of head restraints Adjust the head restraint properly to achieve maximum protection. Properly adjusted head restraints are an important part of – Adjust the head restraint so that its upper edge is at the same level as the top of your head, or as close as possible to the same occupant protection and can reduce the risk of injuries in level as the top of your head and, at the very least, at eye most accident situations.
  • Page 15 WARNING • never lean against the dash panel, Whenever a passenger is seated in the rear central seat, the head restraint • never lie on the rear bench, should be placed in the position for use •...

  • Page 16: Pedal Area

    • Use only floor mats which leave the pedal area free and can be securely never put your feet on the surface of a seat, fastened in the foot well. • never travel in a foot well, •...

  • Page 17: Stowing Luggage

    Safe driving WARNING WARNING • • If the pedals are obstructed, you could cause an accident. Risk of Loose luggage and other objects in the luggage compartment can serious injuries. cause serious injuries. • • Ensure that the floor mats are always securely attached. Always stow objects in the luggage compartment and secure them on •...
  • Page 18 • Never secure a child seat on the fastening rings. Fastening rings There are four fastening rings in the luggage compartment which can be used to secure luggage and other objects.

  • Page 19: Seat Belts

    WARNING •  Seat belt warning lamp* If the seat belts are worn incorrectly or not at all, the risk of severe inju- ries increases. The warning lamp acts as a reminder to the driver to fasten • Properly worn seat belts can reduce severe injuries in the event of the seat belt.
  • Page 20 In addition, an acoustic signal can also be heard for a couple of seconds.  The warning lamp* does not go out until the driver seat belt is fastened while the ignition is switched on.

  • Page 21: Why Wear Seat Belts

    25 km/h to 50 km/h, for example, the kinetic energy increases by a factor of four. Because the passengers in our example are not restrained by seat belts, the entire amount of kinetic energy has to be absorbed at the point of impact ⇒...
  • Page 22 It is also important for the rear passengers to wear seat belts properly, as they could otherwise be thrown forward violently in an accident. Rear passengers who do not use seat belts endanger not only themselves but also the front ⇒...
  • Page 23 Further, properly worn seat belts improve the protection provided by airbags in the event of an accident. For this reason, wearing a seat belt is required by law in most countries.

  • Page 24: Seat Belts

    • position by a latch. Do not allow the seat belt to be damaged or jammed, or to rub on any sharp edges. • Never wear the seat belt under the arm or in any other incorrect posi- tion.
  • Page 25 • Never put the latch plate in the buckle of another seat. If you do this, the seat belt will not protect you properly and the risk of injury is increased.
  • Page 26 An incorrectly worn seat belt web can cause severe injuries in the event of an accident. • The shoulder part of the seat belt must lie on the centre of the shoulder, never across the neck. The seat belt must lie flat and snugly on the torso ⇒ page 23, fig.
  • Page 27 • WARNING For pregnant women, the lap part of the seat belt must lie as low as possible over the pelvis, never across the stomach, and always lie flat so Never unbuckle a seat belt while the vehicle is in motion. If you do, you that no pressure is exerted on the abdomen.

  • Page 28: Belt Tension Devices

    The seat belts for the front occupants are equipped with belt tension devices. Sensors will trigger the belt tension devices during severe head-on, lateral and rear collisions only if the seat belt is being worn. This retracts and Incorrectly fastened seat belts tightens the seat belts, reducing the forward motion of the occupants.
  • Page 29 The belt tension device and seat belt including its automatic retractor cannot be repaired. • Any work on the belt tension devices and seat belts, including the removal and refitting of system parts in conjunction with other repair work, must be performed by a qualified workshop only.

  • Page 30: Airbag System

    • sustain critical injuries. Therefore, it is essential that all occupants maintain If you are not wearing a seat belt or if you lean forward or to the side or a correct sitting position while travelling. assume an incorrect sitting position, the risk of injury is increased substantially.
  • Page 31 An enabled front airbag on the front passenger side is potentially a major − Follow the installation instructions of the child seat manufacturer danger to a child. The front passenger seat is life threatening to a child if you and absolutely observe the warnings ⇒ page 43, “Child safety”.
  • Page 32 Airbag system Monitoring of airbag and belt tension device system damaged. The consequence may be that, in the event of an accident, the airbag inflates incorrectly or does not inflate at all. The functionality of the airbag and belt tension device system is constantly ...

  • Page 33: Front Airbags

    The airbag system is not a substitute for seat belts, but is an integral part of the vehicle's overall passive safety system. Please bear in mind that the airbag system can only work effectively when the occupants are wearing their seat belts correctly and have adjusted the head restraints properly.
  • Page 34 • or if the vehicle rolls. WARNING • The seat belts and airbags can only provide maximum protection if the occupants are seated correctly ⇒ page 9, “Proper sitting position for occu- pants”. • If a fault should occur in the airbag system, have the system checked immediately by a qualified workshop.
  • Page 35 Airbag system In order to provide the desired extra protection in an accident, the airbags may develop when the airbag deploys. This is normal and is no indication have to deploy extremely rapidly (within fractions of a second). A fine dust that there was a fire in the vehicle.

  • Page 36: Side Airbags

    • If you are not wearing a seat belt or if you lean forward or to the side or assume an incorrect sitting position, the risk of injury is increased substantially. This increased risk of injury will be further increased if you are struck by an inflating airbag.
  • Page 37 Airbag system The airbag system is not a substitute for seat belts, but is an integral part of WARNING (continued) the vehicle's overall passive safety system. Please bear in mind that the • airbag system can only work effectively when the occupants are wearing their Never drive the vehicle if the loudspeakers in the door panels have seat belts.
  • Page 38 Airbag system Function of side airbags The special design of the airbag allows the controlled escape of the propel- lant gas when an occupant puts pressure on the bag. Thus, the head and Inflated airbags can reduce the risk of head or chest injury in chest are surrounded and protected by the airbag.
  • Page 39 Any work on the side airbag system or removal and installation of the If you do not wear a seat belt, if you lean forward, or are not seated airbag components for other repairs (such as removal of the front seat) correctly while the vehicle is in motion, you are at greater risk of injury should only be performed by qualified workshop.

  • Page 40: Curtain Airbags

    (airbags with gas generator) for the driver, front curtain airbag system”. passenger and passengers on the rear seats, • The airbag system is not a substitute for seat belts, but is an integral part of in the dash panel insert ⇒ page 29.  a warning lamp the vehicle's overall passive safety system.
  • Page 41 WARNING • In order for the curtain airbags to provide their maximum protection, the prescribed sitting position must always be maintained with seat belts while travelling. • Fig. 24 Deployed curtain For safety reasons, the head air bag must be disconnected in those airbags vehicles fitted with a passenger compartment separation screen.
  • Page 42 Airbag system WARNING (continued) • There must be no other persons, animals or objects between the occu- pants of the outer seats and the deployment space of the curtain airbags so that the curtain airbag can deploy without restriction and provide the greatest possible protection.

  • Page 43: Deactivating Airbags

    Airbag system Deactivating airbags* Disabling front passenger airbag If you fit a rear-facing child seat to the front passenger seat, the front passenger front and side airbags must be disabled. Fig. 26 Warning lamp for deactivated passenger airbag in centre console When the passenger airbag is deactivated, this means that only the frontal and side airbags are deactivated.
  • Page 44 Risk of potentially fatal inju- ries to the child! However, if it is necessary in exceptional circumstances to transport a child in a rear-facing child seat on the front passenger seat, you must always disable the front passenger airbag.

  • Page 45: Child Safety

    We recommend that children under 12 years of age be transported on the rear seats. Children travelling on the rear seat must use a child restraint system or the seat belts provided, depending on their age, height and weight. For safety reasons, the child restraint system should be installed in the centre of the rear seat or behind the front passenger's seat.
  • Page 46 Never allow a child to be transported in a vehicle without being properly injury in an accident! secured, or to stand up or kneel on a seat while travelling. In an accident, the child could be flung through the vehicle, causing possibly fatal injuries As the driver, you are responsible for any children you transport in to themselves and other occupants.

  • Page 47: Child Seats

    Child seats that have been tested and approved under the ECE R 44 standard Group 0: For babies from about 9 months old and 10 kg in weight the most bear the test mark on the seat (the letter E in a circle with the test number ⇒ fig.
  • Page 48 Children over 7 years of age weighing between 22 and 36 kg but less than child seats ⇒ in “Safety notes on using child seats” on page 44. 1.5 metres tall are best protected by seat cushions with head restraints in ⇒ fig. conjunction with properly worn seat belts...

  • Page 49: Securing Child Seats

    Securing child seats Ways to secure a child seat A child seat can be secured differently on the rear seat and on the front passenger seat. • You can secure a child seat to the rear seat or front passenger seat in the Child seats in groups 0 to 3 can be secured with a seat belt.
  • Page 50 If it is necessary in exceptional cases to transport a child on the front passenger seat, you must always disable the front passenger – Pull on both sides of the child seat to ensure that it is secure. airbag ⇒ page 41, “Deactivating airbags*”.
  • Page 51 Safety First Operating instructions Tips and Maintenance Technical Data...
  • Page 52 Fig. 31 Instrument panel...

  • Page 53: Operating Instructions

    Cockpit Operating instructions Cockpit Overview Radio casing*/Radio navigation system* Passenger airbag* ........Glove box/Stowage compartment .

  • Page 54: Instruments

    Cockpit Instruments Instrument overview The instruments display the vehicle operating status. Fig. 32 Detail of the dash panel: Instruments The layout of the instruments depends upon the model and engine. Digital clock*/Outside temperature display*/Multifunction display ⇒ page 54 Rev counter* ⇒ page 53 Display field for selector lever position ⇒...
  • Page 55 Cockpit  Rev counter Engine coolant temperature display The rev. counter displays the engine speed in revolutions per This gauge shows the engine coolant temperature. minute. ⇒ page 52, fig. 32 The start of the red zone on the dial indicates the maximum engine speed which may be used briefly when the engine is warm and after it has been run in properly.

  • Page 56: Digital Display In The Instrument Panel

    Cockpit ⇒ fig. When the needle reaches the red area of the reserve zone 34, the WARNING warning lamp will light and an acoustic signal will sound reminding the driver to refuel. At this point there are still about 7 litres of fuel in the tank. When working in the engine compartment, always bear in mind the safety warnings ⇒...
  • Page 57 Cockpit Ambient temperature display* Display with multi-function display (MFD)* The outside temperature is displayed when the ignition is The multi-function display (MFD) shows you diverse journey switched on. and consumption data. At temperatures between +6° C to -7°C , in addition to the outside tempera- ture, an ice crystal is displayed and if travel speed is over 10 km/h an acoustic buzzer is heard.
  • Page 58 Cockpit Displays in the multi-function display (MFD)* The multi-function display is equipped with two automatic memo- ries: 1 - Trip memory and 2 - Total journey memory. The selected memory will be shown in the upper right-hand corner of the display. Selecting memory –...
  • Page 59 Cockpit Memory displays Ø litre/100km - Average fuel consumption • ⇒ page 56, fig. 38 Time The average fuel consumption will be shown after a • distance of approximately 100 metres has been travelled. Dashes will appear Journey duration in the display until that time. The display will be updated every 5 seconds •...
  • Page 60 Cockpit Display field for selector lever position* Service interval display When it is time for a service, the lower counter (trip counter) of the speedom- eter displays the symbol of a spanner, followed by one of the following The position of the automatic gearbox selector lever is shown on the display ⇒...
  • Page 61 Cockpit Note • Only the desired service message should be reset in each case. By pressing the reset button it is possible to change from one message to another. • Do not reset the display between two service intervals, otherwise the dispaly will be incorrect.

  • Page 62: Warning Lamps

    Cockpit Warning lamps Overview of the warning lamps The warning lamps indicate a number of different functions and possible faults. Fig. 40 Instrument panel with warning lamps. Some of the warning lamps listed in this section are only fitted on certain models or are optional extras.
  • Page 63  Airbag or belt tension device system fault or airbag disabled ⇒ page 26 ⇒ page 29  ⇒ page 17 Seat belt warning lamp*  ⇒ page 66 Fault in the emission control system Safety First...
  • Page 64 Cockpit Item Symbol Meaning of warning and control lamps Further information  Traction control system (TCS)*/Electronic stabilisation pro- ⇒ page 66 gram (ESP)*  ⇒ page 66 Electronic immobiliser  ⇒ page 67 Engine oil pressure  ⇒ page 67 Trailer turn signals in operation ...
  • Page 65 Cockpit   Electro-hydraulic steering* Glow plug system / Engine fault The warning lamp lights up to show that the glow plugs are The level of steering assistance depends on the vehicle speed and on the preheating. It flashes if there is an engine fault. steering angle.
  • Page 66 Cockpit  Coolant Level* / temperature WARNING (continued) • The warning lamp lights up if the coolant temperature is too Never open the bonnet if you can see or hear steam or coolant escaping high or if the coolant level is too low. from the engine compartment.
  • Page 67 Cockpit  Anti-lock brake system (ABS) WARNING (continued) A warning lamp system monitors the ABS. wheels to lock quickly when you brake. This could cause the rear to break away. Risk of skidding. Drive carefully to the nearest qualified workshop ...
  • Page 68 The immobiliser will be activated again automatically as soon as you pull the key out of the ignition “Brakes” lock. The engine can, however, be started if the appropriate coded SEAT genuine key is used.
  • Page 69 Cockpit Differential lock fault (EDL)* Note EDL operates along with the ABS in vehicles equipped with an The vehicle cannot be operated properly if you do not have a genuine SEAT key. Electronic Stabilisation Program (ESP)*  A malfunction in the EDL is indicated by the ABS warning lamp .

  • Page 70: Audio Control From Controls On The Steering

    Steering wheel controls* Steering wheel controls* Audio control from controls on the steering wheel Fig. 41 Controls on the Fig. 42 Controls on the steering wheel steering wheel Short press Long press Button Radio CD Audio CD mp3 Radio CD Audio CD mp3 Volume up Continue volume up...
  • Page 71 Steering wheel controls* Search down- Search down- Previous track Rewind wards for station wards for station Change source cycle No specified function Silence No specified function Change folder Change CD Next preset No function No specified function Previous folder Previous CD Previous preset No function No specified function...

  • Page 72: Central Locking

    Unlocking and locking Unlocking and locking Central locking Safety system “Safe” This is an anti-theft device consisting of a double lock for the Description door locks and a deactivation function for the boot in order to make forced entry more difficult. The central locking system enables you to lock and unlock all the doors and the tailgate from one point.
  • Page 73 Unlocking and locking Selective unlocking system* When the “Safe” system is deactivated, the doors are locked using the simple locking system, meaning that they may be opened from the interior but not This system allows for unlocking only the driver's door, or all from the exterior.
  • Page 74 Unlocking and locking Locking system for involuntary unlocking WARNING This is an anti-theft system and will avoid situations where When the vehicle is in motion, the internal door release levers should not the vehicle is opened unintentionally be operated, this could cause a door to open. The vehicle will be re-locked automatically, if it is unlocked and neither the boot or any of the doors are opened within 30 seconds.
  • Page 75 Unlocking and locking Locking the vehicle WARNING (continued) ⇒  – Press the button • While the ignition is not activated after unlocking the door lock cylinder with the key. Unlocking the doors  – Press the button Note • ...
  • Page 76 Unlocking and locking Childproof locks This function is independent of the electronic opening and locking systems of the vehicle. It only affects the rear doors. It is only The childproof lock prevents the rear doors being opened possible to activate it and deactivate it manually, as described from the inside.

  • Page 77: Keys

    Unlocking and locking Keys Key set The set of keys includes a remote control, a key without a remote control and a key tab with the number of the key. Fig. 47 Folding key The key set belonging to your vehicle consists of the following items: •...
  • Page 78 Unlocking and locking To fold the key bit, press the button and push with the hand, until it is ⇒ page 75, fig. 47. correctly folded Duplicate keys If you need a replacement key, take your key tab to an Authorised Service Centre.

  • Page 79: Radio Frequency Remote Control

    Unlocking and locking Radio frequency remote control Locking and unlocking the vehicle The remote control key can be used to lock and unlock the vehicle from a distance. Fig. 49 Range of the remote control The following functions can be performed using the remote control and without using the key itself •...
  • Page 80 Unlocking and locking • ⇒ fig. 48   close the vehicle, press the close button briefly . The indica- If the vehicle is unlocked using the button, the vehicle will be tors flash once. locked again automatically if any of the doors or the tailgate are not opened within 30 seconds of unlocking the vehicle.

  • Page 81: Anti-Theft Alarm System

    Unlocking and locking Anti-theft alarm system* – Maximum time allowed for synchronising is 30 seconds. – The normal key is used to activate the ignition, and the key with the remote control is the key to be programmed. Description of anti-theft alarm system* –...
  • Page 82 Unlocking and locking Volumetric sensor* The horn is sounded and the turn signals flash for approx. 30 seconds. How is the alarm switched off? Monitoring or control function incorporated in the anti-theft To deactivate the anti-theft alarm, rotate the key in the opening direction or alarm*, that detects unauthorized vehicle entry using ultra- press the button ...
  • Page 83 Unlocking and locking Note • If, after deactivating the volumetric sensor, the vehicle is locked using the remote control or the key in the door lock in under 30 seconds, the volumetric sensor will remain deactivated. The other functions of the antitheft alarm* will remain activated.

  • Page 84: Tailgate

    Unlocking and locking Tailgate Opening and locking The operation of the tailgate opening system is electric. It is activated by using the handle on the tailgate Fig. 51 Closing the tail- gate Opening the tailgate ⇒ fig. – Pull on the release lever and lift the tailgate 50.

  • Page 85: Windows

    Unlocking and locking Windows If the keyhole is in horizontal position, this implies that the tailgate is locked and can only be opened using the main key. Opening or closing the windows electrically WARNING • The front and rear electric windows can be operated using the Always close the tailgate properly.
  • Page 86 Unlocking and locking Buttons in the driver door WARNING (continued) Button for window in front left door • If necessary, use the safety switch to disable the rear electric windows. Button for window in front right door Make sure that they have been disabled. Buttons for rear windows* Safety switch for deactivating the electric window buttons in the rear Note...
  • Page 87 Unlocking and locking – Use the key to lock the vehicle from outside and hold the key in The one-touch function and roll-back function will not work if there is a malfunction in the electric windows. Contact an Authorised Service Centre. the lock position for at least one second.

  • Page 88: Sliding/Tilting Roof

    Unlocking and locking Sliding/tilting roof* Tilting the sliding/tilting sunroof – Turn the rotary button to position Opening and closing the sliding/tilting roof Always close the sliding/tilting roof fully if you park the vehicle or leave it unattended ⇒ The sliding/tilting sunroof is opened and closed using the rotary button when the ignition is switched on.
  • Page 89 Unlocking and locking Convenience closing* Using the door lock – Hold the key in the door lock of the driver's door in the locking position until the sliding/tilting sunroof is closed. – Release the key to interrupt this function. Note The sliding/tilting sunroof rotary button remains in the last position selected Fig.

  • Page 90: Lights And Visibility

    Lights and visibility Lights and visibility Lights Switching on the fog lights*   – Turn the switch from position to the first stop. The  symbol in the light switch lights up.  Switching lights on and off Switching on the rear fog lights (vehicles with front fog lights) ...
  • Page 91 Lights and visibility • The rear fog light is so bright that it can dazzle drivers behind you. You Headlight range control should use the rear fog light only when visibility is very poor. Using the electrical headlight range control, you can adjust the headlight •...
  • Page 92 Lights and visibility 1. Park your vehicle at a safe distance from moving traffic. For the sake of the environment 2. Press the button to switch on the hazard warning lights ⇒ The rear window heater should be disconnected as soon as the glass is demisted.
  • Page 93 Lights and visibility The turn signal and main beam headlight lever has the following WARNING (continued) functions: • Never park where the catalytic converter could come into contact with Switching on the turn signals inflammable materials under the vehicle, for example dry grass or spilt petrol.

  • Page 94: Interior Lights

    Lights and visibility Interior lights WARNING The main beam can dazzle other drivers. Risk of accident! Never use the Front interior light main beam headlights or the headlight flasher if they could dazzle other drivers. Note • The turn signals only work when the ignition is switched on. The corre- ...

  • Page 95: Visibility

    Lights and visibility Glove box light* Note If not all the vehicle doors are closed, the interior lights will be switched off The light in the glove box on the front passenger side will only light up if the after approx. 10 minutes, providing the key has been removed and the cour- lights are switched on and the glove box is open.

  • Page 96: Windscreen Washers

    Lights and visibility Windscreen washers – Move the control to the left or right to set the length of the intervals. Control to the left - longer wipe pause, control to the right - shorter wipe pauses. Four wiper interval stages can be set ...
  • Page 97 Lights and visibility Rain sensor* WARNING (continued) • The rain sensor controls the frequency of the windscreen Always note the corresponding warnings on ⇒ page 180. wiper intervals, depending on the amount of rain. Caution In icy conditions, always check that the wiper blades are not frozen to the glass before using the wipers for the first time.
  • Page 98 Lights and visibility Switching off the interval wipe function Note – Pull the lever back from position towards the steering wheel. • Do not put stickers on the windscreen in front of the sensor. This may The wiper will continue to function for a short period if you switch cause sensor disruption or faults.

  • Page 99: Mirrors

    Lights and visibility Headlight washer system Automatic anti-dazzle interior mirror* The headlight washers clean the headlight lenses. The automatic anti-dazzle function can be switched on and off as desired. The headlight washers are activated automatically when the windscreen washer is used and the windscreen wiper lever is pulled towards the steering wheel for at least 1.5 seconds –...
  • Page 100 Lights and visibility 2. Turn the rotary knob to position the mirror so that you have a Note good view to the rear of the vehicle. • The automatic anti-dazzle function will only work properly if the sun 3. Turn knob to position R (right exterior mirror). blind* for the rear window is retracted and there are no other objects preventing light from reaching the interior mirror.
  • Page 101 Lights and visibility WARNING • The rear view convex or aspheric mirror increase the field of vision however the objects appear smaller and further away in the mirrors. If you use these mirrors to estimate the distance to vehicles behind you when changing lane, you could make a mistake.

  • Page 102: The Importance Of Correct Seat Adjustment

    Always keep your feet in the foot well when the vehicle is moving; never Proper seat adjustment optimises the level of protection rest them on the dash panel, out of the window or on the seat. This also offered by seat belts and airbags.

  • Page 103: Head Restraints

    Seats and stowage Head restraints Correct adjustment of head restraints Properly adjusted head restraints are an important part of occupant protection and can reduce the risk of injuries in most accident situations. Fig. 70 Viewed from side: Properly adjusted head restraints and proper belt adjustment –...
  • Page 104 The head restraints can be adjusted by moving them up and down. Adjusting height (rear central seat) – Press the button on the side and pull upwards to the desired position. – To lower the head restraint, press the button and push head restraint downwards.

  • Page 105: Electric Front Seats

    Please observe the safety warnings ⇒ page 101, “Correct adjustment of head restraints”. Note • To fit and remove the rear head restraints, gently tilt the seat back forwards. • When fitting the head restraints again, insert the tubes as far as possible into the guides without pressing the button.
  • Page 106 You can push tilted far to the rear. The maximum protection of the seat belt can be the seat forwards at the same time to make entry to the rear seats achieved only when the backrests are in an upright position and the driver easier.

  • Page 107: Rear Seat Bench

    The seat heating is switched off in the 0 position. The seat heating only works when the ignition is switched on. The left thumb wheel controls the left seat and the right thumb wheel the right seat.

  • Page 108: Stowage Compartments

    • After raising the backrest, check it has engaged properly in position . • The three point automatic seat belt only works correctly when the back- Fig. 76 Passenger side: Stowage compartment rest of the central seat is correctly engaged.
  • Page 109 Seats and stowage Object compartment, driver's side Stowage drawer under front right seat* There is an object compartment on the driver's side Fig. 78 Stowage compartment under the front passenger seat Fig. 77 Driver's side compartment To open ⇒ fig. 77.
  • Page 110 Seats and stowage Front cup holder* Rear cup holder* Fig. 79 Front cup holder Fig. 80 Cupholder in the in the centre console centre console To open On the rear part of the centre console, behind the hand brake, there is a ⇒...

  • Page 111: Ashtrays, Cigarette Lighter And Electrical Sockets

    Seats and stowage Ashtrays, cigarette lighter and electrical Closing – Move the ashtray cover towards the gearstick until it engages. sockets WARNING Front ashtray Never put paper in the ashtray. Hot ash could ignite the paper in the ashtray. Cigarette lighter Fig.

  • Page 112: First-Aid Kit, Warning Triangle, Fire Extinguisher

    Seats and stowage First-aid kit, warning triangle, fire WARNING extinguisher • Improper use of the cigarette lighter can lead to serious injuries or start a fire. • Take care when using the cigarette lighter. Carelessness or negligence First aid kit, warning triangle and fire extinguisher when using the cigarette lighter can cause burns, risk of injury.

  • Page 113: Luggage Compartment

    Seats and stowage Luggage compartment Caution Hard objects on the shelf could chafe against the wires of the heating Stowing luggage element in the rear window and cause damage. All luggage must be securely stowed. Note Please observe the following points to ensure the vehicle handles The ventilation slots in front of the rear side windows must not be covered as well at all times: this would prevent stale air being extracted from the vehicle.
  • Page 114 Please observe the following points if you intend to carry loads on the roof: • For safety reasons, only luggage racks and accessories supplied by offi- cial SEAT Service should be used. • It is imperative to precisely follow the fitting instructions included for the...

  • Page 115: Air Conditioning

    Air conditioning Air conditioning Heating output, which is needed to defrost the windows quickly, is only available when the engine has reached its operating temperature. Blower Controls The air flow can be set at four speeds with switch . The blower should always be set at the lowest speed when driving slowly.
  • Page 116 Air conditioning – Set the airflow to the desired direction using air distribution WARNING (continued) control • In air recirculation mode, no ambient air enters the vehicle interior. The – Open the relevant air outlets. windows can quickly fog over if the heating is switched off. Therefore, you should never leave the air recirculation mode switched on for longer Heating the interior periods, as this increases the risk of an accident.
  • Page 117 Air conditioning – Close outlets Heating system Maximum heat output, which is needed to defrost the windows quickly, is – Open and turn outlets towards side windows. only available when the engine has reached its operating temperature. When the windows are demisted and as a preventive measure, the switch Note ...

  • Page 118: Semiautomatic Air Conditioning (Climatic)

    Air conditioning Semiautomatic air conditioning (Climatic) Air distribution Switch on symbol Main air output through outlets: Controls    1, 2, 5  3, 4 The outlets can be closed or opened separately and the air flow directed according to need. Outlet closed: operating lever in vertical position.
  • Page 119 Air conditioning Air distribution control ⇒ page 117 Heating of the vehicle interior ⇒ page 118 Air recirculation button  ⇒ fig. 89 – Disconnect the cooling system using button (the – Coolant on button ⇒ page 117 Button button light goes off). –...
  • Page 120 Air conditioning Cooling system For reasons of safety, air recirculation is not possible when the control for air  distribution is set to the windscreen setting When the cooling system is switched on, not only the temperature, but also the air humidity in the vehicle interior is reduced. This improves comfort for the vehicle occupants and prevents misting of the windows when the outside WARNING air humidity is high.

  • Page 121: Climatronic

    Air conditioning Climatronic Control switches Fig. 90 On the instrument panel: Climatronic controls The air conditioning system only works when the engine is running Air recirculation display: and the blower is switched on. Display for air flow direction Display AUTO (automatic operation) ⇒...
  • Page 122 Air conditioning  Button – Air distribution to footwell A comfortable interior climate is quickly reached when a temperature of +22° C (72° F) is set in automatic mode. It can be changed as necessary to Button  – Air distribution to the upper body. suit individual preferences or particular circumstances.

  • Page 123: General Notes

    Air conditioning If a temperature below 18° C (64° F) is selected, the display switches to LO. In Air recirculation mode prevents strong odours in the ambient air from this setting the system runs at maximum cooling output and the temperature entering the vehicle interior, for example when passing through a tunnel or in is not regulated.
  • Page 124 Air conditioning • For the air conditioning system to work with maximum efficiency, the pollu- At low outside temperatures the compressor switches off automatically. tion filter must be replaced at the intervals specified in the Service Schedule. AUTO button cannot be switched on either. •...

  • Page 125: Steering

    The height and reach of the steering wheel can be freely adjusted to suit the driver. Fig. 92 Proper sitting position for driver – Adjust the driver seat to the correct position. ⇒ fig. 91 down ⇒ – Push the lever under the steering column –...

  • Page 126: Safety

    Driving Safety WARNING (continued) • Adjust the driver seat or steering wheel so that there is a distance of at ⇒ page 123, Electronic stabilisation programme (ESP)* least 25 cm between the steering wheel and your breast bone fig. 92. If you fail to observe the minimum distance, the airbag will not ESP helps make driving safer in certain situations.

  • Page 127: Ignition Lock

    Driving • Ignition lock when rocking the vehicle backwards and forwards to free it from mud, for example. You should press the button to switch the ESP back on when you no longer Position of the ignition key need wheel spin. The TCS and EDL are also switched off if the ESP is switched off.

  • Page 128: Starting And Stopping The Engine

    Wait for the vehicle to come to a standstill before removing the ignition The engine can only be started using a genuine SEAT key with the correct key from the lock. The steering lock could be activated immediately - Risk code.
  • Page 129 10 seconds and try again after about half a minute. If the engine still does not The engine can only be started using a genuine SEAT key with start, the fuel pump fuse should be checked ⇒ page 197, “Fuses”.
  • Page 130 Driving Glow plug system for the diesel engine For the sake of the environment To avoid unnecessary load on the battery, do not use any other major elec- Do not warm-up the engine by running the engine with the vehicle stationary. trical equipment while the glow plugs are pre-heating.

  • Page 131: Manual Gearbox

    Driving – Slide the gearlever to the left, and then into the reverse position Caution shown on the gear lever. If the engine has been driven hard for a long period, the engine could over- heat when it is switched off. Risk of engine damage. For this reason, you Certain versions of the model may include a 6-speed manual gearbox, the should idle the engine for approx.

  • Page 132: Automatic Gearbox

    Driving Automatic gearbox* Note A programme will, depending on the driving resistance, be selected automat- Gearbox programs ically that guarantees more pulling power, thus avoiding having to shift gear constantly. The automatic gearbox has two gearbox programmes. Fig. 96 Section of centre console: selector lever on cars with an automatic gearbox...
  • Page 133 Driving Selector lever lock functions The selector lever lock is released as follows: The selector lever lock in position P or N prevents gears from – Switch on the ignition. being engaged inadvertently, which would cause the vehicle – Press and hold the brake pedal and press the selector lever lock to move.
  • Page 134 Driving N - neutral (idling) Note To take the lever out of position N at speeds of below 5 km/h or when the car The selector lever can be placed in positions 3, 2 and 1 when the change is is at a standstill but the ignition is switched on, depress the brake pedal and made manually, but the automatic gearbox does not change to a lower gear press the lock button on the gearstick knob.
  • Page 135 Driving • If, while driving, the selector lever accidentally moves to position N, first The gearbox does not automatically engage gears. release the accelerator pedal and wait until the engine slows to idling before In this case they can be changed manually. 3rd gear is only available in posi- selecting a forwards gear ⇒...

  • Page 136: Handbrake

    Driving Handbrake Always apply the handbrake firmly. This prevents you driving with the hand- brake applied ⇒  The handbrake warning lamp lights up when the handbrake is applied Using the handbrake and the ignition switched on. The warning lamp goes out when the hand- brake is released.

  • Page 137: Cruise Control System (Ccs)

    Driving Cruise control system (CCS)* – Switch off the engine and remove the key from the ignition lock. Turn the steering wheel slightly to engage the steering lock. – Always take you car keys with you when you leave the vehicle Description ⇒...
  • Page 138 Driving Switching the cruise control system on and off Setting speed* Fig. 100 Turn signal and Fig. 101 Turn signal and main beam lever: switch main beam lever: switch and rocker switch for CCS and rocker switch for CCS ⇒ fig. 101 Switching on the system –...
  • Page 139 Driving Adjusting set speed* When you increase speed with the accelerator and then release the pedal, the system will automatically restore the set speed. This will not be the case, The speed can be altered without touching the accelerator or however, if the vehicle speed is more than 10 km/h higher than the stored speed for longer than 5 minutes.
  • Page 140 Driving • if the clutch pedal is depressed, Vehicles with a manual gearbox • The system is completely turned off by moving the control all the way to if the vehicle is accelerated to over 180 km/h, • the right hand side (OFF engaged), or when the vehicle is stationary, ignition when the lever is moved in the direction of OFF without fully being off.

  • Page 141: Tips And Maintenance

    Intelligent technology Tips and Maintenance Intelligent technology Brakes The brake assist system intervenes here, if you press the brake pedal very quickly, the brake assist system registers an emergency situation. It then very quickly builds up the full brake pressure so that the ABS can be activated Brake servo more quickly and efficiently, thus reducing the braking distance.

  • Page 142: Anti-Lock Brake System And Traction Control Abs

    Intelligent technology Anti-lock brake system and traction control WARNING (continued) • The effectiveness of ABS is also determined by the tyres fitted ⇒ page 185. • If the running gear or brakes are modified, the effectiveness of the ABS Anti-lock brake system (ABS) could be severely limited.

  • Page 143: Electronic Stabilisation Program (Esp)

    Intelligent technology The TCS should be switched on again afterwards as soon as possible. Electronic Stabilising Program (ESP)* ESP reduces the danger of skidding by braking the wheels individually. WARNING The system uses the steering wheel angle and road speed to calculate the •...
  • Page 144 Intelligent technology Anti-lock brake system (ABS) WARNING (continued) • Always adapt your driving style to suit road conditions and the traffic The anti-lock brake system prevents the wheels locking during braking ⇒ page 140. situation. Do not let the extra safety afforded by EDL tempt you into taking any risks when driving, this can cause accidents.

  • Page 145: Driving And The Environment

    Driving and the environment Driving and the environment Running-in Running in tyres and brake pads New tyres should be run-in carefully in the first 500 km. New Running in a new engine brake pads should be run-in carefully in the first 200 km. The engine needs to be run-in over the first 1,500 km.

  • Page 146: Catalytic Converter

    Driving and the environment Authorised Service Centre more frequently than recommended in the Service WARNING (continued) Schedule. • Non-standard or damaged front spoilers could restrict the airflow to the If you drive with wet brakes, for example after driving through water, after brakes and cause them to overheat.

  • Page 147: Driving Abroad

    Centre may only carry out limited repairs. exhaust pipes, catalytic converter or the heat shields on the exhaust SEAT importers and distributors will gladly provide information about the system. These materials could catch fire when the vehicle is driven. technical preparation of your vehicle in addition to necessary maintenance and repair possibilities.
  • Page 148 Driving and the environment Adjusting simple headlights for driving on the left On the left hand side headlight, if you are changing from driving on the left- ⇒ fig. 106. hand side to the right-hand side Covering simple headlights for driving on the right Fig.
  • Page 149 Driving and the environment On the right headlight, if you are changing from driving on the left-hand side to the right-hand side. On the left headlight, if you are changing from driving on the left-hand side to the right-hand side. Covering bifocal headlamps for driving on the left Fig.
  • Page 150 Driving and the environment Covering bifocal headlamps for driving on the right On the left headlight, if you are changing from driving on the left-hand side to ⇒ fig. 112. the right-hand side Covering GDL headlamps for driving on the left Fig.

  • Page 151: Trailer Towing

    Driving and the environment On the right headlight, if you are changing from driving on the right-hand side ⇒ page 148, fig. 113. to the left-hand side On the left headlight, if you are changing from driving on the right-hand side ⇒...
  • Page 152 Driving and the environment Connectors Tyre pressure Your vehicle is fitted with a 12-pin connector for the electrical connection Set tyre pressure to the maximum permissible pressure shown on the sticker between the trailer and the vehicle. on the inside of the fuel tank flap. Set the tyre pressure of the trailer tyres in accordance with the trailer manufacturer's recommendations.

  • Page 153: Driving Economically And With Respect For The Environment

    Driving and the environment Heating WARNING When climbing long hills in hot weather with the engine running fast in a low gear, you should keep an eye on the coolant temperature gauge ⇒ page 51. The towing bracket ball coupling must be stored securely in the luggage compartment to prevent them being flung through the vehicle and causing Electronic Stabilisation Program* injury.
  • Page 154 Driving and the environment Think ahead when driving Avoid short journeys A vehicle uses most fuel when accelerating. If you think ahead when driving, you will need to brake less and thus accelerate less. Wherever possible, let the vehicle roll slowly to a stop, for instance when you can see that the next traffic lights are red.

  • Page 155: Cleaning And Caring For Your Vehicle

    Cleaning and caring for your vehicle Cleaning and caring for your vehicle General notes WARNING (continued) your vehicle. The use of certain products may produce noxious vapours; Regular washing and care help maintain the value of your these should be used in well ventilated areas. vehicle.

  • Page 156: Care Of The Vehicle Exterior

    Cleaning and caring for your vehicle Care of the vehicle exterior – Clean the wheels, sill panels etc. last using a different sponge or glove. – Rinse the vehicle thoroughly with water. Automatic car washes – Dry the surface of the vehicle gently using a chamois leather. The paint is so durable that the car can normally be washed without problems in an automatic car wash.
  • Page 157 Cleaning and caring for your vehicle luggage compartment, or bonnet. This could cause them to freeze. Otherwise WARNING there is a risk of malfunction. • Never wash tyres with a concentrated jet or cylindrical jet (“rotating nozzle”). Even at large spraying distances and short cleaning times, visible For the sake of the environment and invisible damage can occur to the tyres.
  • Page 158 Cleaning and caring for your vehicle Polishing the paintwork Cleaning windows and exterior mirrors Polishing brings back gloss to the paintwork. Cleaning the windows – Moisten the windows with commercially available, alcohol based Polishing is only necessary if the paint has lost its shine, and the gloss cannot be brought back by applying wax.
  • Page 159 Cleaning and caring for your vehicle • Door lock cylinders The heating element for the rear window is located on the inner side of the window. To prevent damage, do not put stickers over the heating elements on The door lock cylinders can freeze up in winter. the inside of the window.
  • Page 160 Cleaning and caring for your vehicle WARNING WARNING • • Never wash tyres with a cylindrical jet. Even at large spraying distances Never wash tyres with a cylindrical jet. Even at large spraying distances and short cleaning times, visible and invisible damage can occur to the and short cleaning times, visible and invisible damage can occur to the tyres.

  • Page 161: Care Of The Vehicle Interior

    Cleaning and caring for your vehicle Cleaning the engine compartment WARNING (continued) • Take special care when cleaning the engine compartment. Moisture, ice and salt on the brakes may affect braking efficiency. Risk of accident. If possible, avoid sudden braking immediately after washing Anti-corrosion treatment the vehicle.
  • Page 162 SEAT does everything possible to preserve the special qualities of leather, as a natural product. Because of the natural properties of the specially selected Cloth seat covers and fabric trim on the doors, headlining etc. can be cleaned hides employed, the finished leather has a certain sensitivity to grease and with a special interior cleanser or with dry foam and a soft brush.
  • Page 163 Keep the seat belts clean and check all seat belts regularly. Cleaning seat belts – Carefully pull the dirty seat belt right out and leave it out. – Clean the dirty seat belts with a gentle soap solution. – Allow the seat belt fabric to dry.

  • Page 164: Accessories, Parts Replacement And Modifications

    Due to the way the electronic components Despite continuous observation of the market, SEAT is not able to assess the are linked together in networks, other systems may be affected by the faults. reliability, safety and suitability of parts not approved by SEAT. For this reason...

  • Page 165: Roof Aerial

    • transmitting power in excess of 10 watts. SEAT has approved your vehicle for use with mobile telephones and two-way radios providing the following conditions are observed: Note • Please observe the operating instructions of your mobile telephone / two-way The correct installation of an external aerial, •...

  • Page 166: Fitting A Towing Bracket

    Accessories, parts replacement and modifications Fitting a towing bracket* It is possible to fit a towing bracket to the rear of the vehicle. Fig. 118 Attachment points for towing bracket...
  • Page 167 Accessories, parts replacement and modifications If a towing bracket is to be fitted after the vehicle is purchased, this must be WARNING (continued) completed according to the instructions of the towing bracket manufacturer. • For your own safety, please observe the instructions provided by the The attachment points for the towing bracket are underneath the vehicle.

  • Page 168: Checking And Refilling Levels

    Checking and refilling levels Checking and refilling levels Refuelling – Turn the key in the lock, without releasing the cap in the clock- ° wise direction 180 The tank flap is released manually. The tank holds approxi- – Remove the key and close the flap until it clicks into place. The mately 45 litres.

  • Page 169: Petrol

    Checking and refilling levels Petrol types are categorised according to their octane number, e. g. 91, 95, WARNING (continued) 98 RON (RON = “research octane number”). You may use petrol with a higher − Insert the fuel nozzle into the mouth of the canister as far as octane number than the one recommended for your engine.

  • Page 170: Diesel

    Checking and refilling levels Diesel Things to note about RME fuel (biodiesel) • The performance of a vehicle using biodiesel maybe somewhat reduced. • Fuel consumption of a vehicle using biodiesel maybe slightly higher. Diesel* • RME fuel can be used in winter at temperatures down to approx. -10°C. •...

  • Page 171: Working In The Engine Compartment

    Do not mix fuel additives (“thinners”, or similar additives) with diesel fuel. All service fluids and consumables, e.g. coolant, engine oil, spark plugs and batteries, are being constantly developed. SEAT provides a constant flow of information to the Authorised Service Centres concerning modifications. For this reason we recommend that you have service fluids and consumables replaced by an Authorised Service Centre.
  • Page 172 Checking and refilling levels WARNING (continued) WARNING • If any work has to be performed when the engine is started or with the All work on the engine or in the engine compartment, e.g. checking and engine running, there is an additional, potentially fatal, safety risk from the refilling fluids, involves the danger of injury and scalding as well as the risk rotating parts, such as the drive belts, alternator, radiator fan, etc., and of accident or fire.
  • Page 173 Checking and refilling levels – Lift the bonnet using the release lever (arrow) and open the For the sake of the environment bonnet. Service fluids leaks are harmful to the environment. For this reason you – Release the bonnet stay and secure it in fixture designed for this should make regular checks on the ground underneath your vehicle.

  • Page 174: Engine Oil

    Checking and refilling levels the different standards for petrol and diesel engines, the oil can be used for WARNING (continued) both types of engines. • After closing the bonnet, always check that it is properly secured. The bonnet must be flush with the surrounding body panels. •...
  • Page 175 Checking and refilling levels Oil properties Viscosity The viscosity class of the oil is selected according to the diagram. When the ambient temperature falls outside the limits of the scale for a short period, an oil change is not required. Fig.
  • Page 176 Checking and refilling levels – Raise the bonnet ⇒ page 171. Note – Pull out the dipstick. Before a long trip, we recommend finding an engine oil that conforms to the corresponding VW specifications and keeping it in the vehicle. This way, the –...
  • Page 177 Checking and refilling levels – To avoid over-filling with engine oil, you should top-up using Caution small quantities, wait a while and check the oil level before If the oil level is above the area do not start the engine. This could result adding any more oil.

  • Page 178: Coolant

    Checking and refilling levels Changing engine oil For the sake of the environment • The engine oil must be changed at the intervals given in the Because of the disposal problems, the necessary special tools and specialist knowledge required, we recommend that you have the engine oil service schedule.
  • Page 179 Checking and refilling levels  Checking the coolant level and topping up WARNING • The correct coolant level is important for fault-free func- The coolant additive is toxic. This represents a toxic danger. Always tioning of the engine cooling system. keep the coolant additive in the original container which should be stored out of the reach of children.
  • Page 180 Checking and refilling levels – If the level is underneath the “MIN” mark, top up with coolant. WARNING (continued) • Topping up coolant When the engine is warm or hot, the cooling system is pressurised! Do not unscrew the cap on the expansion tank when the engine is hot. This is –...

  • Page 181: Washer Fluid And Windscreen Wiper Blades

    Checking and refilling levels Washer fluid and windscreen wiper blades WARNING Any work carried out in the engine compartment or on the engine must be  Topping up washer fluid carried out cautiously. • When working in the engine compartment, always observe the safety The water for cleaning the windscreen should always be warnings ⇒...
  • Page 182 Checking and refilling levels Changing windscreen wiper blades – Make sure that the blade faces down when fitting a blade with integrated deflector blade. If the windscreen wiper blades are in perfect condition, you will benefit from an improved visibility. Damaged wiper If the windscreen wipers rub, they should be replaced if they are damaged, blades should be replaced immediately.
  • Page 183 Checking and refilling levels Changing the rear wiper blade If the windscreen wiper rubs, it should be replaced if it is damaged, or cleaned if it is soiled. A good rear wiper blade is essential for clear rear vision. If this is not sufficient, refer to a qualified workshop. Damaged wiper blades should be replaced immediately.

  • Page 184: Brake Fluid

    It important that you use only use brake fluid compliant with the US standard black and yellow cap. FMVSS 116 DOT 4. We recommend the use of Genuine SEAT brake fluid. The brake fluid level drops slightly when the vehicle is being used as the brake pads are automatically adjusted as they wear.

  • Page 185: Battery

    Checking and refilling levels Battery WARNING (continued) • Before opening the bonnet to check the brake fluid level, read and observe the warnings ⇒ page 169. Warnings on handling the battery • Brake fluid should be stored in the closed original container in a safe place out of reach of children.
  • Page 186 Checking and refilling levels • If the vehicle is left standing in cold conditions for a long period, protect WARNING (continued) the battery from frost. If it “freezes” it will be damaged. charge. Never short the battery terminals. High-energy sparks can cause injury.

  • Page 187: Wheels

    The battery has been developed to suit the conditions of their location and has special safety features. Storing tyres Genuine SEAT batteries fulfil the maintenance, performance and safety spec- – Mark tyres when you remove them to indicate the direction of ifications of your vehicle.
  • Page 188 Checking and refilling levels Checking tyre pressure New tyres New tyres have to be run in ⇒ page 143. The correct tyre pressure can be seen on the sticker on the The tread depth of new tyres may vary, according to the type and make of tyre inside of the tank flap.
  • Page 189 Checking and refilling levels Tyre service life Wear indicators The original tyres on your vehicle have 1.6 mm high “tread wear The service life of tyres is dependent on tyre pressure, driving indicators”⇒ fig. 129 running across the tread. Depending on the make, style and fitting.
  • Page 190 Tyres should be replaced at least in pairs and not individually (i.e. both front approved by SEAT for your model. Failure to do so could impair vehicle tyres or both rear tyres together). A knowledge of tyre designations makes it...
  • Page 191 The prescribed torque for wheel bolts for steel and alloy wheels is 120 Nm. wheels or tyres which have not been approved by SEAT for use with your model may invalidate the vehicle's type approval for use on public roads.
  • Page 192 Checking and refilling levels Snow chains Information on permitted winter tyre sizes can be found in the vehicle's regis- tration documents. Use only radial winter tyres. All tyre sizes listed in the vehicle documentation also apply to winter tyres. Snow chains may be fitted only to the front wheels, and only to certain tyre sizes ⇒...

  • Page 193: If And When

    If and when If and when Vehicle tools, spare wheel WARNING (continued) • The jack supplied by the factory is only designed for changing wheels Vehicle Tools on this model. On no account attempt to use it for lifting heavier vehicles or other loads, risk of injury.
  • Page 194 If and when – Engage the first gear, or put the selector lever to position P for – Take off the wheel and then put on the spare wheel those vehicles with an automatic gearbox. – Lower the vehicle. – If you are towing a trailer, unhitch it from your vehicle. –...
  • Page 195 If and when Wheel trims Wheel covers* The wheel trims must be removed to gain access to the wheel The wheel covers must be removed for access to the wheel bolts. bolts Fig. 131 Changing a wheel: Removing the Fig. 132 Remove the wheel trim wheel cover Removing...
  • Page 196 If and when – An adapter is required to unscrew or tighten the theft inhibiting Loosening the wheel bolts wheel bolts. The wheel bolts must be loosened before raising the vehicle. WARNING Loosen the wheel bolts only about one turn before raising the vehicle with the jack, loosening the wheel bolts more than one turn can result in an acci- dent.
  • Page 197 If and when Raising the vehicle – Locate the jacking point under the door sill closest to the wheel ⇒ fig. 134. being changed The vehicle must be raised with a jack to remove the wheel. – Wind up the jack under the jacking point until the arm of the jack is directly below the vertical rib under the door sill.
  • Page 198 If and when Removing and fitting the wheel The wheel bolts should be clean and turn easily. Before fitting the spare wheel, inspect the condition of the wheel and hub mounting surfaces. These For removal and fitting the wheel, the following tasks must be surfaces must be clean before fitting the wheel.

  • Page 199: Fuses

    If and when Fuses – Insert the adapter onto the wheel bolt and push it on as far as it ⇒ page 196, fig. will go 137. – Fit the box spanner as far as it will go over the adapter. Changing a fuse –...
  • Page 200 If and when steering wheel on the right the fuses are on the right-hand side of the instru- ment panel, behind a cover. The electric windows are protected by circuit breakers. These reset automat- ically after a few seconds when the overload (caused for example by frozen windows) has been corrected.
  • Page 201 If and when Fuses on left side of dash panel Fuses Number Electrical equipment Amperes Secondary water pump 1.8 20 VT (T16) ABS/ESP Vacant Brake light, clutch switch, relay coils Engine control unit (petrol) Right side light Left side light Mirror heating unit Lambda probe Signal“S”...
  • Page 202 If and when Number Electrical equipment Amperes Main beam headlight, left Number plate light/side light indicator Rear windscreen wiper Injectors(fuel) Brake light switch /ESP (Turn sensor) Instrument panel/Diagnosis Unit: glovebox light, boot light, interior light Climatronic Power supply central locking unit Left front window control Vacant Self powered alarm horn...
  • Page 203 If and when Number Electrical equipment Amperes Windscreen wiper unit Heated rear window unit Indicator unit Cigarette lighter Locking unit Radio/CD/GPS/Telephone Horn Dipped headlight (left side) Right rear window control The signal “S”is a system which includes the starter and steering lock and enables, after the ignition is switched off and without removing the key from the steering and starter lock, certain electrical components to be switched on, including for example, the radio, the courtesy light, etc.
  • Page 204 If and when Fuses in engine compartment above battery Fig. 139 Fuse box above battery Metal fuses Number Electrical equipment Amperes Alternator/Starter motor Power supply voltage distributor inside vehicle Power assisted steering pump Spark plug preheating (diesel) Electroblower clima heater/fan ABS unit...
  • Page 205 If and when Non-metal fuses Number Electrical equipment Amperes ABS unit Electroblower clima heater/fan ABS unit Cable control unit Clima fan Vacant Jatco unit for automatic gearbox Vacant Vacant Vacant Position in engine compartment: side box Fuses Number Electrical equipment Amperes Alternator <...

  • Page 206: Lamp Change

    If and when Number Electrical equipment Amperes Multi-terminal voltage supply “30”. Internal fuse box Trailer fuse voltage supply in internal fuse box Vacant Some of the electrical items listed in the table are only fitted on certain Rear lights on tailgate models or are optional extras.
  • Page 207 If and when Main headlight lamps Fog lights* Fog light 12V/55W (H3) Registration plate light Registration plate light - C5W Caution • The halogen lamps (H3, H7, H4...) are pressurised and might explode on changing them. • Therefore protective gloves and glasses should be worn when changing a halogen lamp.
  • Page 208 If and when Side lights Indicator lights Dipped headlight lamp Fig. 143 Dipped head- light lamp – Raise the bonnet. ⇒ fig. 142 – Remove the loops outwards in the direction of the arrow and remove the cover. Fig. 142 Dipped head- ⇒...
  • Page 209 If and when ⇒ fig. 144 Main beam lights – Remove the loops outwards in the direction of the arrow and remove the cover. ⇒ fig. 145. – Remove the lamp cable connector – Undo the retainer spring and remove. –...
  • Page 210 If and when ⇒ fig. 146 Side beam lights – Remove the loops in the direction of the arrow and remove the cover. – Pull on the cables to release the lamp holder from the casing ⇒ fig. 147. – Pull on the lamp and replace. –...
  • Page 211 If and when ⇒ fig. 148 Turn indicator lamps – Remove the loops in the direction of the arrow and remove the cover. – Turn the lamp holder to the left and remove from casing ⇒ fig. 149 – Installation is done in the reverse order. –...
  • Page 212 If and when ⇒ fig. 150 Fog lights – Undo the two fastening screws and when released unplug the connector. – Turn the headlamp cover to the left a quarter turn. – Unplug the lamp cable. – Undo the lamp retainer spring and remove. –...
  • Page 213 If and when Side indicator lamps Rear lights on the tailgate: Access to the light unit Fig. 153 Rear light on tailgate Fig. 152 Side indicators – Press the indicator to the left or to the right to remove the lamp. –...
  • Page 214 If and when ⇒ page 211, fig. 153 – Remove the plastic cover and the ⇒ page 211, fig. 153 plastic caps carefully levering using a screwdriver using the flat part of a screwdriver; avoid damage to the paintwork. ⇒ page 211, fig. 154 –...
  • Page 215 If and when ⇒ fig. 157 Rear lights on frame – Unscrew the bolts with the flat part of the screw- driver. – Move the light unit outwards and pull. – If necessary, unplug the connector. ⇒ fig. – Unscrew the bolt 158.

  • Page 216: Jump-Starting

    If and when Interior light and front reading light – First fit the glass with the fastening tabs over the frame of the switch. Next press the front part until the two long tabs click on the support. Additional brake lights* Given the difficulty involved in the replacement of this light it should be done by the Technical Service.
  • Page 217 If and when Jump lead terminal connections Jump leads – Switch off the ignition on both vehicles ⇒ Jump leads must comply with the standard DIN 72553 (see manufacturer's documentation). The wire cross section must be at least 25 mm for petrol ⇒...
  • Page 218 If and when 10. When the engine is running, disconnect the leads in reverse WARNING (continued) order to the details given above. • Do not bend over the batteries. This could result in chemical burns. Connect the battery clamps so they have good metal-to-metal contact with the battery terminals.

  • Page 219: Towing And Tow-Starting

    If and when Towing and tow-starting Towing eyes Tow-starting* The use of jump leads is preferable to tow-starting. We recommend that you do not tow-start your vehicle. Jump-starting is preferable ⇒ page 214. However, if your vehicle has to be tow-started: –...
  • Page 220 If and when Fitting the front towing eye As the brake servo does not work if the engine is not running, you must apply considerably more pressure to the brake pedal than you normally would. – First remove the right hand cover from the lower part of the bumper.

  • Page 221: Technical Data

    General notes on the technical data Technical Data General notes on the technical data What you should be aware of General notes All data in the official vehicle documents take precedence over this data. All data in these documents are valid for the basic model as offered in Spain. The figures may be different if additional equipment is fitted, for different The vehicle data card included in the inspection and maintenance schedule models, for special vehicles and for other countries.
  • Page 222 General notes on the technical data Vehicle identification data Vehicle identification number The vehicle identification number (chassis number) can be read from outside the vehicle through a viewer in the windscreen. This is located on the left- hand side of the vehicle in the lower area of the windscreen. It is also located on the right hand side of the engine compartment.

  • Page 223: How Are The Figures Measured

    General notes on the technical data How are the figures measured? Fuel consumption Fuel consumption and emission values are determined according to Euro- measuring cycles are carried out on a rolling road test bed. The test criteria pean Commission Directive 99/100/EC. They take the actual kerb weight are as follows: (weight class) into consideration.

  • Page 224: Towing A Trailer

    General notes on the technical data Weights Drawbar load The maximum permitted weight exerted by the trailer drawbar on the ball joint of the towing bracket must not exceed 75 kg. Kerb weight refers to the basic model with a fuel tank filled to 90% capacity and without optional extras.
  • Page 225 General notes on the technical data Snow chains Snow chains may be fitted only to the front wheels. Chains may be used on the following tyres 155/80 R 13; 165/70 R 14 and 185/80 R 14. Consult the chapter “wheels” of this manual. Wheel bolts After the wheels have been changed, the tightening torque of the wheel bolts should be checked as soon as possible with a torque wrench ⇒...

  • Page 226: Technical Data

    Technical Data Technical Data Checking fluid levels Overview Further explanations, instructions and restrictions on the technical data are contained as of ⇒ page 219. From time to time, the levels of the different fluids in the vehicle must be checked. Never fill with incorrect fluids, to do so may cause serious damage to the engine.

  • Page 227: Petrol Engine 1.2 47 Kw (64 Cv)

    Technical Data Petrol engine 1.2 47 kW (64 CV) General engine data Power output in kW (bhp) 47 (64)/ 5000 Maximum torque in Nm at rpm 112/ 3000 No. of cylinders, capacity 3/ 1198 in cm Compression 10.4 Fuel Super 95 RON /Normal 91 RON Research-Octane-Number = Measure of the predetonation power of the petrol.

  • Page 228: Petrol Engine 1.4 16 V 55 Kw (75 Cv)

    Technical Data Gross axle weight, front in kg Gross axle weight, rear in kg Permitted roof load in kg Trailer weights With no brakes, gradients up to 12% With brakes, gradients up to 12% Engine oil capacity Engine oil capacity with oil filter change 3.3 litres Petrol engine 1.4 16 V 55 kW (75 CV) General engine data...
  • Page 229 Technical Data Performance figures Maximum speed in km/h Acceleration from 0-80 km/h in sec. Acceleration from 0-100 km/h in sec. 13.2 Consumption (litres/100 km)/ CO (g/km) 3 door 5 door Urban cycle 8.6/ 206 8.7/209 Extra urban cycle 5.3/ 127 5.4/ 130 Combined 6.5/ 156...

  • Page 230: Petrol Engine 1.4 16 V 55 Kw (75 Cv) Automatic

    Technical Data Petrol engine 1.4 16 V 55 kW (75 CV) Automatic General engine data Power output in kW (bhp) 55 (75)/ 5000 Maximum torque in Nm at rpm 126/ 3800 No. of cylinders, capacity 4/ 1390 in cm Compression 10,5 Fuel Super 95 RON...

  • Page 231: Petrol Engine 1.4 16 V 74 Kw (101 Cv)

    Technical Data Gross axle weight, front in kg Gross axle weight, rear in kg Permitted roof load in kg Trailer weights With no brakes, gradients up to 12% With brakes, gradients up to 12% Engine oil capacity Engine oil capacity with oil filter change 3.5 litres Petrol engine 1.4 16 V 74 kW (101 CV) General engine data...
  • Page 232 Technical Data Performance figures Maximum speed in km/h Acceleration from 0-80 km/h in sec. Acceleration from 0-100 km/h in sec. 11.2 Consumption (litres/100 km)/ CO (g/km) 3 door 5 door Urban cycle 8.9/ 214 9.0/216 Extra urban cycle 5.3/ 127 5.4/ 130 Combined 6.6/ 158...

  • Page 233: Petrol Engine 1.8 20 Vt 110 Kw (150 Cv)

    Technical Data Petrol engine 1.8 20 VT 110 kW (150 CV) General engine data Power output in kW (bhp) 110 (150)/ 5500 Maximum torque in Nm at rpm 220/ 1450-4500 No. of cylinders, capacity 4/ 1781 in cm 9,5 ± 0,5 Compression Fuel Super 95 RON...

  • Page 234: Diesel Engine 1.4L Tdi 51 Kw (70 Bhp)

    Technical Data Gross axle weight, front in kg Gross axle weight, rear in kg Permitted roof load in kg Trailer weights With no brakes, gradients up to 12% With brakes, gradients up to 12% 1200 Engine oil capacity Engine oil capacity with oil filter change 4.3 litres Diesel engine 1.4l TDI 51 kW (70 bhp) General engine data...
  • Page 235 Technical Data Performance figures Maximum speed in km/h Acceleration from 0-80 km/h in sec. Acceleration from 0-100 km/h in sec. 14.8 Consumption (litres/100 km)/ CO (g/km) 3 door 5 door Urban cycle 5.9/159 6.0/162 Extra urban cycle 4.1/111 4.2/113 Combined 4.7/127 4.8/130 Weights...

  • Page 236: Diesel Engine 1.4L Tdi 59 Kw (80 Bhp)

    Technical Data Diesel engine 1.4l TDI 59 kW (80 bhp) General engine data Power output in kW (bhp) 59 (80)/ 4000 Maximum torque in Nm at rpm 195/ 2200 No. of cylinders, capacity 3/ 1492 in cm 19.5 ± 0.5 Compression Fuel Min 49 CN...

  • Page 237: Diesel Engine 1.9 Tdi 74 Kw (101 Cv)

    Technical Data Gross axle weight, front in kg Gross axle weight, rear in kg Permitted roof load in kg Trailer weights With no brakes, gradients up to 12% With brakes, gradients up to 12% 1000 Engine oil capacity Engine oil capacity with oil filter change 3.8 litres Diesel engine 1.9 TDI 74 kW (101 CV) General engine data...
  • Page 238 Technical Data Performance figures Maximum speed in km/h Acceleration from 0-80 km/h in sec. Acceleration from 0-100 km/h in sec. 10.8 Consumption (litres/100 km)/ CO (g/km) 3 door 5 door Urban cycle 6.4/173 6.5/176 Extra urban cycle 4.0/108 4.1/111 Combined 4.9/132 5.0/135 Weights...

  • Page 239: Diesel Engine 1.9L Tdi 96 Kw (131 Bhp)

    Technical Data Diesel engine 1.9l TDI 96 kW (131 bhp) General engine data Power output in kW (bhp) 96(131)/ 4000 Maximum torque in Nm at rpm 310/ 1900 No. of cylinders, capacity 4/ 1896 in cm Compression Fuel Min 49 CN Cetane-Number (cetane index) = Measure of the combustion power of the diesel.
  • Page 240 Technical Data Gross axle weight, front in kg Gross axle weight, rear in kg Permitted roof load in kg Trailer weights With no brakes, gradients up to 12% With brakes, gradients up to 12% 1200 Engine oil capacity Engine oil capacity with oil filter change 4.3 litres...

  • Page 241: Dimensions And Capacities

    Technical Data Dimensions and capacities Dimensions Length, width 3.953 mm/ 1.698 mm Height at kerb weight 1.441 mm Front and rear projection 931 mm/ 662mm Wheelbase 2.460 mm Turning circle 10.54 m Front Rear 1.435 mm 1.424 mm Track width 1.419 mm 1.408 mm Capacities...

  • Page 243: Index

    Warning lamp ......29 Adjusting the seat belt height ....25 Anti-freeze .
  • Page 244 Clock ........54 Child seat ....... 45 Emergency unlocking system .
  • Page 245 Duplicate keys ......76 seat ....... 29 Engine oil .
  • Page 246 Jump-starting: description ....215 Front seat adjustment Headlight flasher ......91 Lumbar support .
  • Page 247 ......88 Demisting the windscreen and side windows . . Rear seat bench ......105 Rear seats, MFD .
  • Page 248 Roof carrier* ......112 Seat belts ....... 17 After the fuel tank has been run dry .
  • Page 249 Traction control system Why wear seat belts? ....17, 19 Car care products ..... 153 warning lamp .
  • Page 250 Index Winter tyres ......189 Wiper/wash automatic function ... . . 94 Working in the engine compartment .
  • Page 251 SEAT S.A. is permanently concerned about continuous development of its types and models. For this reason we ask you to understand, that at any given time, changes regarding shape, equipment and technique may take place on the car delivered. For this reason no right at all may derive based on the data, drawings and descriptions in this current handbook.
  • Page 252 auto emoción...

Table of Contents