Mitsubishi Electric MELSEC L Series User Manual page 175

Error code
Description and cause of error
(decimal)
In the normal
output mode
*1
60
In the wave output
mode
Among CH1 Warning output upper limit value (Un\G86) to CH8
Warning output lower limit value (Un\G101), any of the lower limit
*1
62
value is greater than or equal to the corresponding upper limit value.
 indicates the number of a channel where an error occurs.
In offset/gain setting mode, a value set to Offset/gain adjustment
*1
700
value specification (Un\G24) is outside the range.
A value outside -32000 to 32000 is set to any of CH1 Scaling lower
*1
limit value (Un\G54) to CH8 Scaling upper limit value (Un\G69).
90
 indicates the number of a channel where an error occurs.
Among CH1 Scaling lower limit value (Un\G54) to CH8 Scaling
upper limit value (Un\G69), any of the lower limit value is greater
*1
91
than or equal to the corresponding upper limit value.
 indicates the number of a channel where an error occurs.
*1 This error code can be cleared by setting a value within the setting range and performing either of the following
operations.
• Turning on and off Error clear request (YF)
• Turning on and off Operating condition setting request (Y9)
*2 If an error occurs, D/A conversion performed in all channels will stop.
Therefore, after performing the offset/gain setting again, reconfigure initial settings.
*3 If an error occurs, D/A conversion performed in the error channel will stop.
Therefore, after performing the offset/gain setting again, reconfigure initial settings.
*4 An error code is not stored in Latest error code (Un\G19) but in the completion status of the G(P). OGSTOR instruction
+1.
S
For Switch 1 to 5, refer to the following.
• Intelligent function module switch setting (
A value outside the setting range is set to
CH Digital value (Un\G1 to Un\G8).
 indicates the number of a channel where
an error occurs.
A digital value outside the setting range is set
to a part of areas used for channel wave
output in Wave data registry area (Un\G5000
to Un\G54999).
 indicates the number of a channel where
an error occurs.
CHAPTER 11 TROUBLESHOOTING
Action
Set a value within the following range to CH Digital value (Un\G1
to Un\G8) according to the set output range. The setting range is
shown below.
■For L60DA4
• 0 to 20mA, 4 to 20mA, 0 to 5V, 1 to 5V: 0 to 20000
• -10 to 10V, user range: -20000 to 20000
■For L60DAVL8, L60DAIL8
• 0 to 20mA, 4 to 20mA, 0 to 5V, 1 to 5V: 0 to 8000
• -10 to 10V: -16000 to 16000
• User range: -8000 to 8000
However, when Scaling enable/disable setting (Un\G53) is set to
Enable (0), the setting range is as follows.
• CH Scaling lower limit value (Un\G54, Un\G56, Un\G58,
Un\G60, Un\G62, Un\G64, Un\G66, Un\G68) to CH Scaling
upper limit value (Un\G55, Un\G57, Un\G59, Un\G61, Un\G63,
Un\G65, Un\G67, Un\G69)
Set a value within the following range to the corresponding part of
areas used for the channel in Wave data registry area (Un\G5000
to Un\G54999) according to the set output range. The setting range
is shown below.
■For L60DA4
• 0 to 20mA, 4 to 20mA, 0 to 5V, 1 to 5V: 0 to 20000
• -10 to 10V: -20000 to 20000
■For L60DAVL8, L60DAIL8
• 0 to 20mA, 4 to 20mA, 0 to 5V, 1 to 5V: 0 to 8000
• -10 to 10V: -16000 to 16000
(The error data can be checked in CH1 Wave output digital value
outside the range Address monitor (L) (Un\G1156) to CH8 Wave
output digital value outside the range Address monitor (H)
(Un\G1171).)
Correct the value so that the upper limit value is greater than the
lower limit value.
Set a value within -3000 to 3000 to Offset/gain adjustment value
specification (Un\G24).
Set a value within the range of -32000 to 32000 in CH1 Scaling
lower limit value (Un\G54) to CH8 Scaling upper limit value
(Un\G69).
Correct the value so that the scaling upper limit value is greater
than the scaling lower limit value.
Page 238, Appendix 9.1 (2))
11
173