CPI CLS Advance Operator's Manual page 56

Troubleshooting
Error code Description/Cause
Coin not accepted as normal
0x8y83
coin acceptance band inhibited
y = 0..F
by control software (security
= Coin
level (narrow acceptance band)
Type 0–15
activated)
0x8y90 Hardware error during coin
y = 0..F acceptance
= Coin
Type 0–15
0x8y91 Coin could not be accepted and
y = 0..F was rejected as at least two
= Coin coins entered the measurement
Type 0–15 area at the same time
0x8y93 Coin could not be accepted due
y = 0..F to polling timeout
= Coin
Type 0–15
0x8y94 Coin was rejected as coin ac-
y = 0..F ceptance was not polled
= Coin
Type 0–15
Coin was rejected as coin posi-
0x8y96
tion sensors covered
y = 0..F
= Coin
Type 0–15
0x8y99 Coin was rejected as event
y = 0..F buffer is full
= Coin
Type 0–15
0x8y9B Coin was rejected as previous
y = 0..F coin has not been accepted yet
= Coin
Type 0–15
0x8y9C Coin was rejected as previous
y = 0..F coin has not been rejected yet
= Coin
Type 0–15
0x8y9E Coin was rejected as validator
y = 0..F misses coin to be accepted
= Coin
Type 0–15
0x8y9F Coin was rejected as validator
y = 0..F misses coin to be rejected
= Coin
Type 0–15
56
Category Remedy/hints By whom
Info If unintended, configuration Service
failure, contact service
Info
Info Insert coin(s) again Customer
Info If info comes up repeatedly, Service
configuration failure, contact
service
Info If info comes up repeatedly, Service
configuration failure, contact
service
Attention • Eliminate jam/foreign • Attendant possessing
object the key for the upper/
(cf. Chap. "8.5.1 Elimi-
nating coin jam in acceptance lower lock
unit", p. 38)
• Cleaning, contact service • Service
Info
Info Insert coin again Customer
Info Insert coin again Customer
Info • Insert coin again • Customer
• Cleaning, contact service • Service
Info • Insert coin again • Customer
• Cleaning, contact service • Service
Error code Description/Cause Category
0x8yA0 Accepted coin has not reached Info
y = 0..F hopper yet
= Coin
Type 0–15
0x9yzz Number of coins accepted Info
y = 0..F but not sorted correctly (only
= Coin transmitted if not equal to coins
Type 0–15 sorted and can be compared
zz = number with zz out of 0x7y)
of coins
Coin was rejected as not mea- Info
0xC000 sured within the acceptance
band programmed
Coin was accepted though Info
0xC063 measured beyond the accep-
tance band programmed
Hardware error during coin Info
0xC090
acceptance
Coin could not be accepted and Info
was rejected as at least two
0xC091
coins entered the measurement
area at the same time
Coin could not be accepted due Info
0xC093 to polling timeout
Coin was rejected as coin ac- Info
0xC094 ceptance was not polled
Coin was rejected as coin posi- Attention
tion sensors covered
0xC096
Coin was rejected as event Info
0xC099
buffer is full
Coin was rejected as previous Info
0xC09B
coin has not been accepted yet
Coin was rejected as previous Info
0xC09C
coin has not been rejected yet
Sensor detected unknown Info
0xC09D
object and no coin
Coin was rejected as validator Info
0xC09E
misses coin to be accepted
CLS Advance
Remedy/hints By whom
Insert coin(s) again Customer
If info comes up repeatedly, Service
configuration failure, contact
service
If info comes up repeatedly, Service
configuration failure, contact
service
• Eliminate jam/foreign • Attendant possessing
object the key for the upper/
(cf. Chap. "8.5.1 Elimi-
nating coin jam in acceptance lower lock
unit", p. 38)
• Cleaning, contact service • Service
Insert coin again Customer
Insert coin again Customer
• Insert coin again • Customer
• Cleaning, contact service • Service
OM_CLS_-_EN_2-0