CPI CLS Advance Operator's Manual page 52

Troubleshooting
Error code Description/Cause Category
Hopper 6 replied with BUSY Info
0x8667 status code after sending
hopper a command
Lack of change. CLS control Attention
unit wants the hopper 6 to
0x8668
pay out more coins than
available
Hopper reset. Hopper 6 Info
0x8669
detected a power-up
Hopper 6 replied with wrong Info
0x866A
checksum
Enter hopper 6 firmware Info
0x86C8
update mode ACK
Begin hopper 6 firmware Info
0x86C9
update ACK
Upload hopper 6 firmware Info
0x86CA
ACK
Finish hopper 6 firmware Info
0x86CB
update ACK
Hopper 7 firmware bundle Attention
0x8723
version mismatch
Hopper 7 configuration Attention
0x8724
bundle version mismatch
CLS control unit retrying Info
communication after unsuc-
0x8764
cessfully attempting to com-
municate with a hopper 7
Hopper 1 replied with NACK Info
0x8766 status code after sending
hopper a command
Hopper 7 replied with BUSY Info
0x8767 status code after sending
hopper a command
Lack of change. CLS control Attention
unit wants the hopper 7 to
0x8768
pay out more coins than
available
Hopper reset. Hopper 7 Info
0x8769
detected a power-up
Hopper 7 replied with wrong Info
0x876A
checksum
Enter hopper 7 firmware Info
0x87C8
update mode ACK
52
Remedy/hints By whom
Refill hopper Attendant possessing
(cf. Chap. "8.1 Filling the
coin hoppers", p. 31)
the key for the lower
lock
FW file failure, contact service Service
Configuration file failure, contact Service
service
Refill hopper Attendant possessing
(cf. Chap. "8.1 Filling the
coin hoppers", p. 31) the key for the lower
lock
Error code Description/Cause Category
Begin hopper 7 firmware Info
0x87C9
update ACK
Upload hopper 7 firmware Info
0x87CA
ACK
Finish hopper 7 firmware Info
0x87CB
update ACK
Hopper 8 firmware bundle Attention
0x8823
version mismatch
Hopper 8 configuration Attention
0x8824
bundle version mismatch
CLS control unit retrying Info
communication after unsuc-
0x8864
cessfully attempting to com-
municate with a hopper 8
Hopper 8 replied with NACK Info
0x8866 status code after sending
hopper a command
Hopper 8 replied with BUSY Info
0x8867 status code after sending
hopper a command
Lack of change. CLS control Attention
unit wants the hopper 8 to
0x8868
pay out more coins than
available
Hopper reset. Hopper 8 Info
0x8869
detected a power-up
Hopper 8 replied with wrong Info
0x886A
checksum
Enter hopper 8 firmware Info
0x88C8
update mode ACK
Begin hopper 8 firmware Info
0x88C9
update ACK
Upload hopper 8 firmware Info
0x88CA
ACK
Finish hopper 8 firmware Info
0x88CB
update ACK
Coin return tray is full. CLS Attention
0x8901
stops operating
The coin return tray was Info
0x8902 previously full and it went
back to not full condition
CLS Advance
Remedy/hints By whom
FW file failure, contact service Service
Configuration file failure, contact Service
service
Refill hopper Attendant possessing
(cf. Chap. "8.1 Filling the
coin hoppers", p. 31)
the key for the lower
lock
Empty return tray Customer / attendant
OM_CLS_-_EN_2-0