CPI CLS Advance Operator's Manual page 55

CLS Advance
Error code Description/Cause
Configuration data block check-
sum error
0x2030
Firmware checksum error
0x2031
Coin validator hardware error
0x2032
Coin validator misses coin sig-
nal from coin return conveyor
0x2042
motor
Sorting control sensor blocked
0x2050 (due to coin jam or foreign
object)
Sorting control sensor 1..8
0x2051..8 blocked (due to coin jam or
foreign object)
Could not add coin to event
0x2060
queue
Could not get coin from event
0x2061
queue
0x4y01..8 Coin accepted, detected to be
y = 0..F coin type 0..15 and registered
= Coin in 1..8
Type 0–15
1..8 = Sort-
ing chute
Power lost event
• during reset cycle (no error)
• due to power failure for
instance during operation
0x5000
(error)
Battery low event
0x5001
OM_CLS_-_EN_2-0
Category Remedy/hints By whom
Critical • Configuration failure, • Service
contact service
• Hardware replacement, • Service
contact service
Critical • FW file failure, contact • Service
service
• Hardware replacement, • Service
contact service
Critical Hardware replacement, Service
contact service
Critical • Connection/installation • Service
failure, contact service
• Hardware replacement, • Service
contact service
Critical Eliminate jam/foreign object Attendant possessing
(cf. Chap. "8.5.1 Eliminating coin the key for the upper/
jam in acceptance unit", p. 38)
lower lock
Critical Eliminate jam/foreign object Attendant possessing
(cf. Chap. "8.5.1 Eliminating coin
the key for the upper/
jam in acceptance unit", p. 38)
lower lock
Attention Reset CLS Attendant/service
Attention Reset CLS Attendant/service
Info
Info
• No error
• Open acceptance unit • Attendant possessing
(cf.
Chap. "7.3 Opening and clos- the key for the upper
ing the upper coin acceptance
lock
and return coins
unit", p. 47)
on centrifuge to customer.
Supply CLS with voltage.
Critical Change battery Service
Error code Description/Cause Category
0x7yzz Number of coins [zz] of coin Info
y = 0..F type 0..15 sorted
= Coin
Type 0–15
zz = number
of coins
sorted
0x8y60 Sorting timeout. Coin not Info
y = 0..F sorted within given time period
= Coin
Type 0–15
0x8y61 Acceptance timeout. Coin not Info
y = 0..F accepted within given time
= Coin period
Type 0–15
Unintended coin acceptance. Attention
Coin should have been rejected
0x8y63
but was accepted
y = 0..F
= Coin
Type 0–15
Unintended coin rejection. Coin Attention
should have been accepted but
0x8y64
was rejected
y = 0..F
= Coin
Type 0–15
Sorting error. Coin was sorted Attention
into the wrong hopper
0x8y65
y = 0..F
= Coin
Type 0–15
0x8y80 Coin not accepted as CLS not Info
y = 0..F in acceptance state
= Coin
Type 0–15
0x8y81 Coin not accepted as coin Info
y = 0..F inhibited by control software
= Coin
Type 0–15
Troubleshooting
Remedy/hints By whom
Cleaning, contact service Service
If necessary, contact service Service
for cleaning
• Open lid and upper ac- • Attendant possessing
ceptance unit the key for the upper
(cf. Chap. "7.3
Opening and closing the coin lock
acceptance unit", p. 27)
and free rejector pin
• Cleaning, contact service
• Service
• Open lid and upper ac- • Attendant possessing
ceptance unit the key for the upper
(cf. Chap. "7.3
Opening and closing the upper lock
coin acceptance unit", p. 47)
and free rejector pin
• Cleaning, contact service
• Service
• Eliminate jam/foreign • Attendant possessing
object the key for the upper/
(cf. Chap. "8.5.1 Elimi-
nating coin jam in acceptance lower lock
from sorting
unit", p. 38)
spiral/chutes
• Cleaning, contact service
• Service
If unintended, configuration Service
failure, contact service
If unintended, configuration Service
failure, contact service
55