CPI CLS Advance Operator's Manual page 54

Troubleshooting
Error code Description/Cause Category
Coin input funnel master Info
0x8E6C
inhibit set
0x8E6D Coin input funnel was reset Info
Coin(s) detected in coin input Info
0x8E6E
funnel. CLS started operation
Main PCB firmware bundle Attention
0x9123
version mismatch
CLS control unit retrying Info
communication after unsuc-
0x9164
cessfully attempting to com-
municate with Main PCB
Main PCB replied with NACK Info
0x9166 status code after sending
Main PCB a command
Main PCB replied with BUSY Info
0x9167 status code after sending
Main PCB a command
Main PCB replied with wrong Info
0x9168
checksum
Main PCB replied with Info
0x9169
unknown command
Main PCB replied with not Info
0x916A
allowed
Main PCB replied with bad Info
0x916B
parameter
Main PCB is entering boot Info
0x91CC
loader mode
Main PCB is exiting boot Info
0x91CD
loader mode
Main PCB sent ACK for Info
0x91CE command "verify CRC and
set OK"
Main PCB sent ACK for com- Info
0x91CF
mand "write data to buffer"
Main PCB sent ACK for Info
0x91D0 command "compare buffer
with flash"
Main PCB sent ACK for com- Info
0x91D1
mand "prepare sector"
Main PCB sent ACK for com- Info
0x91D2
mand "erase sector"
54
Remedy/hints By whom
FW file failure, contact service Service
Error code Description/Cause Category
Main PCB sent ACK for com- Info
0x91D3
mand "copy buffer to flash"
10.2.2.2 Error codes transmitted by the CLS coin validator
Error code Description/Cause
Coin validator disabled by
0x0001
control software
0x1000 Coin validator was reset
Coin jam in measurement area
or sensors covered
0x2010
Centrifuge blocked and cannot
turn forward or backword
0x2015
Coin transport belt blocked
0x2016
Measurement timeout during
measurement
0x2018
Measurement timeout during
compensation
0x2019
Operating voltage low
0x2020
Operating voltage high
0x2021
Remedy/hints By whom
Category Remedy/hints By whom
Info If unintended, configuration Service
failure, contact service
Info
Attention • Eliminate jam/foreign • Attendant possessing
object the key for the upper/
(cf. Chap. "8.5.1 Elimi-
nating coin jam in acceptance lower lock
unit", p. 38)
• Cleaning, contact service • Service
Attention • Eliminate jam/foreign • Attendant possessing
object the key for the upper
(cf. Chap. "8.5.1 Elimi-
nating coin jam in acceptance lock/lower lock
unit", p. 38)
• Service
• Cleaning, contact service
Attention • Eliminate jam/foreign • Attendant possessing
object the key for the upper
(cf. Chap. "8.5.1 Elimi-
nating coin jam in acceptance lock/lower lock
from belt
unit", p. 38)
• Cleaning, contact service
• Service
Info If necessary, Eliminate jam/ Attendant possessing
foreign object the key for the upper/
(cf. Chap. "8.5.1
Eliminating coin jam in acceptance
lower lock
unit", p. 38)
Info If necessary, Eliminate jam/ Attendant possessing
foreign object the key for the upper/
(cf. Chap. "8.5.1
Eliminating coin jam in acceptance lower lock
unit", p. 38)
Critical • Make sure that CLS is • Attendant
connected correctly
(cf.
Chap. "6.4 Putting the CLS into
service", p. 24)
• Service
• Connection failure, contact
service
Critical • Make sure that CLS is • Attendant
connected correctly
(cf.
Chap. "6.3 Putting the CLS into
service", p. 47)
• Service
• Connection failure, contact
service
)
CLS Advance
OM_CLS_-_EN_2-0