1.16.1
P2 Pin Definitions
Table 1-7 Provides the pin definitions and signal maps for the P2 Military Connector.
P2
Interface
Pin
1
Gigabit Ethernet 1
2
Gigabit Ethernet 1
3
Gigabit Ethernet 1
4
Ground
5
Gigabit Ethernet 1
6
Gigabit Ethernet 1
7
Gigabit Ethernet 1
8
Gigabit Ethernet 1
14
Gigabit Ethernet 1
9
USB 2.0, Port 4
10
USB 2.0, Port 4
11
USB 2.0, Port 4
12
USB 2.0, Port 5
13
USB 2.0, Port 5
27
USB 2.0, Port 5
15
USB 2.0, Port 4
16
USB 2.0, Port 5
17
Serial 4
18
Serial 4
19
Serial 4
20
Serial 4
21
Serial 6
22
Serial 6
23
Serial 6
24
Serial 6
25
Power
26
Power
27
Ground
28
USB 2.0, Port 8
30
USB 2.0, Port 8
31
USB 2.0, Port 8
32
USB 2.0, Port 8
29
Reset Switch
38
Ground
33
Control/Indicator
44
Ground
34
Control/Indicator
44
Ground
35
NC
44
Ground
36
Control/Indicator
37
Control/Indicator
HPERC-IBR-M Setup
Signal
GbE2_MDI0_P
GbE2_MDI1_N
GbE2_MDI1_P
GND
GbE2_MDI2_N
GbE2_MDI2_P
GbE2_MDI3_N
GbE2_MDI0_N
GbE2_MDI3_P
USB_P4
USB_N4
USB_GND4
USB_P5
USB_N5
USB_GND5
P5V_USB4
P5V_USB5
RS422_TX4_N
RS422_TX4_P
RS422_RX4_N
RS422_RX4_P
RS422_RX6_N
RS422_RX6_P
RS422_TX6_N
RS422_TX6_P
P5V
P5V
GND
USB_PWR8
USB_P8
USB_N8
USB_GND8
RESET#_HDR
GND
PWR_LED
GND
PCIe_ETH_2/5_LED1
GND
NC
GND
HPOUT_R
HPOUT_L
Table 1-7: P2 Military Connector Signals
Signal Description
Ethernet1 MDI0 Positive
Ethernet1 MDI1 Negative
Ethernet1 MDI1 Positive
Ground
Ethernet1 MDI2 Negative
Ethernet1 MDI2 Positive
Ethernet1 MDI3 Negative
Ethernet1 MDI0 Negative
Ethernet1 MDI3 Positive
Data Positive
Data Negative
Ground
Data Positive
Data Negative
Ground
+5 Volts Power
+5 Volts Power
Transmit Data Negative
Transmit Data Positive
Receive Data Negative
Receive Data Positive
Receive Data Negative
Receive Data Positive
Transmit Data Negative
Transmit Data Positive
+5 Volts Power
+5 Volts Power
Ground
USB 2.0 +5V Power
USB 2.0 Data Positive
USB 2.0 Data Negative
USB 2.0 Ground
Resets the system
Ground
Power LED (330ohm to +5V)
Ground
Ethernet LED
Ground
Not Connected
Ground
Audio Right
Audio Left
HPERC-IBR-M
15
Need help?
Do you have a question about the HPERC-IBR-MC and is the answer not in the manual?