Chrysler DODGE D150 1993 Service Manual page 708

— 5.9L ENGINE 9 - 103
SPECIFICATIONS—5.9L ENGINE
EmmmE SPECIFICATIONS
Camshaft
Bearing Diameter
N o
i 50.800 - 50.825 mm
" " (2.000 - 2.001 in)
N o
2 50.394-50.419 mm
' (1.984- 1.985 in)
N o
3 50.013 - 50.038 mm
(1.969- 1 970 in)
No 4 49.606 - 49.632 mm
(1.953 - 1.954 in)
No 5 ................ 39.683 -39.713 mm
(1.5625- 1.5635 in)
Diametrical Clearance 0.0254 - 0.0762 mm
(0.001 - 0.003 in)
Max. Allowable . 0.127 mm
(0.005 in)
End p |
a y
0.051 - 0.254 mm
(0.002-0.010 in)
Bearinq Journal Diameter
N o
i
50.749 - 50.775 mm
(1.998- 1.999 in)
No 2 50.343 - 50.368 mm
(1.982- 1.983 in)
No 3 . .............. 49.962 - 49.987 mm
(1.967- 1.968 in)
No 4 . 49.555-49.581 mm
(1.951 - 1 952 in)
No 5 39.637 - 39.662 mm
(1.5605- 1.5615 in)
Connecting Rods
Bearing Clearance 0.0127 - 0.0559 mm
(0.0005 - 0.0022 in)
Piston Pin Bore Diameter 24.966 - 24.978 mm
(0.9829 - 0.9834 in)
Side Clearance (Two Rods) ......................... 0.152 - 0.356 mm
(0.006-0.014 in)
Total Weight (Less Bearing) . ... • 758 grams
(25.74 oz)
Crankshaft
Connecting Rod Journal
Diameter . 53.950 - 53.975 mm
(2.124 - 2.125 in)
Out-of-Round (Max.) 0.0254 mm
(0.001 in)
Taper (Max.) ... 0.0254 mm
(0.001 in)
Diametrical Clearance
No 1 ... ........ 0.0127 - 0.0381 mm
(0.0005-0.0015 in)
Max Allowable (No.l) - 0.0381 mm
(0.0015 in)
Nos.2, 3, 4 and 5 0.0127 - 0.0508 mm
(0.0005 - 0.0020 in)
Max. Allowable (Nos.2, 3, 4 & 5) ...... - 0.0635 mm
(0.0025 in)
End Play 0.051 -0.178 mm
(0.002 - 0.007 in)
Max. Allowable 0.254 mm
(0.010 in)
Main Bearing Journals
Diameter 71.361 - 71.387 mm
(2.8095- 2.8105 in)
Out-of-Round (Max.) 0.0254 mm
(0.001 in)
Taper (Max.) .., 0.0254 mm
(0.001 in)
Cylinder Block
Cylinder Bore
Diameter , 101.60 - 101.65 mm
(4.000 - 4.002 in)
Out-of-Round (Max.) ........... 0.127 mm
(0.005 in)
Taper (Max.) 0.254 mm
(0.010 in)
Distributor Lower Drive Shaft
Bushing (Press Fit in Block) 0.0127 - 0.3556 mm
(0.0005-0.0140 in)
Shaft-to-Bushing Clearance 0.0178 - 0.0686 mm
(0.0007 - 0,0027 in)
Tappet Bore Diameter .............. 22.99 - 23.01 mm
(0.9051 - 0.9059 in)
Cylinder Head
Compression Pressure 689 kPa
(100 psi)
Gasket Thickness (Compressed) 1.2065 mm
(0.0475 In)
Valve Seat
Angle . 44.25° - 44.75°
Runout (Max.) ....................... 0.0762 mm
(0.003 in)
Width (Finish) - Intake 1.016-1.524 mm
(0,040-0.060 in)
Width (Finish) - Exhaust 1.524-2.032 mm
(0.060-0.080 in)
Hydraulic Tappets
Body Diameter 22.949 - 22.962 mm
(0.9035 - 0.9040 in)
Clearance in Block 0.0279 - 0.0610 mm
(0.0011 - 0.0024 in)
Dry Lash . 1.524 - 5.334 mm
( 0 . 0 6 0 - 0 2 1 0 in)
Push Rod Length 190.63 - 191.14mm
(7.505 - 7.525 in)
J9309-102